Engineering Commons^™

Evaluation Of A Bulge Reduction Technology For Corrugated Fiberboard Containers Under Static Compression, Daan Peleman, Jay Singh, Koushik Saha, Soma Roy

Industrial Technology and Packaging

This research examines the effect of top-to-bottom static compression load on the bulge of RSC containers. The study compares a control regular slotted container (RSC) constructed with corrugated fiberboard to tape-reinforced designs. The bulge reduction, achieved using various tape placements and conditioning environments, were measured. Currently, no research on the effect of reinforcement tape towards reduction in the out-of-plane displacement (bulging) of the corrugated fiberboard panels has been undertaken. Samples related to four different container designs, varying by presence, quantity and the position of the reinforcement tape on the vertical panels, were tested and analyzed. The study involved the use …

Influence Of Fiberboard Container Design On Compression Bulge Displacement, Koushik Saha, Shane Messner, John Dizon, Nirav Chhajed, Jay Singh

Industrial Technology and Packaging

Bulge effect is the out-of-plane displacement of a panel of a corrugated fiberboard box from its original position. This bulge effect often is the result of excessive weight being placed on a box that rests at the bottom of a palletized load. Panels that are out-of-plane reduce the stacking strength of the box and can result in damage to products inside the containers. This study was designed to find the influence of fiberboard container design on its bulging performance when under compression. The objective of the study was to determine if change in height of a regular slotted container will …

Knee Joint Biomechanics In Transtibial Amputees In Gait, Cycling, And Elliptical Training, Greg Orekhov, A. Matt Robinson, Scott J. Hazelwood, Stephen M. Klisch

Biomedical Engineering

Transtibial amputees may experience decreased quality of life due to increased risk of knee joint osteoarthritis (OA). No prior studies have compared knee joint biomechanics for the same group of transtibial amputees in gait, cycling, and elliptical training. Thus, the goal of this study was to identify preferred exercises for transtibial amputees in the context of reducing risk of knee OA. The hypotheses were: 1) knee biomechanics would differ due to participant status (amputee, control), exercise, and leg type (intact, residual) and 2) gait kinematic parameters would differ due to participant status and leg type. Ten unilateral transtibial amputee and …

2-Axis Electric Off-Road Bucket Seat Bases, Brennan K. Slater, Alexander P. Croteau, Spencer M. Kubik

Mechanical Engineering

Off-road vehicle bucket seats are currently restricted to a single position relative to the floor of the vehicle. Drivers and riders desire the ability to adjust their seat position to increase comfort and allow for a greater size range of riders to fit safely within the cabin or roll cage. To develop a viable solution, the team has gone through an extensive design process and has constructed a functioning prototype. This Final Design Report encapsulates the entire design process and concludes with recommendations for changes we would make looking both back in review as well as moving forward with further …

A Comparison Of The Army Corps Of Engineers Hydrologic Modeling System And Autodesk Storm And Sanitary Analysis For Hydraulic And Hydrologic Analysis And Design, Foster Josef Heifetz Campbell

Master's Theses

Hydrological and hydraulic effects of urban development is one of the key issues of study for improved water management. The addition of impervious surfaces to once pervious land and re-routing open channels and flow paths can cause flooding or declining water levels within a watershed. Many studies of these issues have found that there can be multiple factors causing hydrological and hydraulic impacts, and it can be hard to analyze and develop effective solutions without appropriate drainage software packages. However, there are multiple software packages available for use, and determining the correct one to use for a specific challenge can …

Hybrid Iii 95th Percentile Large Male Finite Element Model Neck Alteration, Eric Riley Day

Master's Theses

The motivation behind the project was to update the Livermore Software Technology Corporation (LSTC) Hybrid III 95th percentile finite element model, such that the neck assembly response under varying simulated loading conditions equals that of the federally regulated Hybrid III 95th percentile anthropomorphic testing device (ATD).

The family of Hybrid III crash test dummies approximate the physical properties and response of the human body in a frontal automotive crash. The Hybrid III is used to assess the effectiveness of vehicle restraint systems. LSTC offers Hybrid III finite element models for use in their Multiphysics simulation software package, LS-DYNA. The Hybrid …

Development Of An Analysis Tool And Weight Estimation Method For Aircraft Wing Structures, Kevin M. Barton

Master's Theses

The goal of this effort was to build an analysis tool for aircraft wings and incorporate it into a program that optimizes the wing structure for the lowest weight for the conceptual design phase. The analysis tool calculates the internal stresses in primary load carrying members using established analysis methods for semimonocoque beams. Via a Graphical User Interface (GUI) built in MATLAB, the user can define the structural layout and material properties of the load carrying members. The program requires a degenerate geometry model built with Vehicle Sketch Pad (OpenVSP) to define the outer mold line (OML) of the wing, …

Design, Modeling And Control Of A Two-Wheel Balancing Robot Driven By Bldc Motors, Charles T. Refvem

Master's Theses

The focus of this document is on the design, modeling, and control of a self-balancing two wheel robot, hereafter referred to as the balance bot, driven by independent brushless DC (BLDC) motors. The balance bot frame is composed of stacked layers allowing a lightweight, modular, and rigid mechanical design. The robot is actuated by a pair of brushless DC motors equipped with Hall effect sensors and encoders allowing determination of the angle and angular velocity of each wheel. Absolute orientation measurement is accomplished using a full 9-axis IMU consisting of a 3-axis gyroscope, a 3-axis accelerometer, and a 3-axis magnetometer. …

Blood Glucose Predictor, Jessica Patterson

Electrical Engineering

For my senior project, I perform data analysis using statistical methods to determine body metrics that correlate with blood glucose levels. Working with Dr. Tina Smilkstein, I take repeat measurements from 6 different volunteers to establish trends in bodily metric data. The data taken includes weight, body fat, pulse rate, VO2, blood glucose, blood pressure, hours slept, and quality of sleep. Using these values, I use the program MiniTab to view results.

A few examples of correlations with blood glucose found in this project are:

• Systolic blood pressure for females had a regression line of 124.0 -0.3366*Blood Pressure. This indicates …

Bitcoin Price Prediction Using Neural Networks, Vladislav Killiakov

Electrical Engineering

In this project, I will investigate the performance of several major neural network architectures for the task of Bitcoin price prediction. Bitcoin is a cryptocurrency that is recently becoming increasingly more popular, and more widely adopted as a financial instrument. As a result, more efforts have been made in the past several years to model and predict its price. However, to this moment a large portion of work on Bitcoin price modeling was done using statistical or classical machine learning techniques. At the same time, other artificial intelligence based prediction techniques, and specifically neural networks, have not been explored to …

Reasoning From Point Clouds, Joey Wilson

Computer Engineering

Over the past two years, 3D object detection has been a major area of focus across industry and academia. This is primarily due to the difficulty of learning data from point clouds. While camera images are fixed size and can therefore be easily trained on using convolution, point clouds are unstructured series of points in three dimensions. Therefore, there is no fixed number of features, or a structure to run convolution on. Instead, researchers have developed many ways of attempting to learn from this data, however there is no clear consensus on what is the best method, as each has …

Mobile Robot Platform, Sukhman S. Marok

Electrical Engineering

The Mobile Robot Platform is a research and development tool designed for researchers working in the field of robotics. The cost of existing mobile robot platforms can easily be in the thousands of dollars, leading many researchers to choose between spending the time to create their own platform or buying an expensive pre-existing solution. The Mobile Robot Platform proposed combines pre-existing open source software and hardware solutions, along with a strong mechanical base that is capable of navigating on flat surfaces. The robot is designed to have many of the necessary components needed for teleoperation as well as autonomous navigation. …

Free Space Optical Communication, Anuj Gohil

Electrical Engineering

Communication is key to day to day activities for all companies and people. Wireless communication has made us expect more from our tools. Radio Frequency has been the preferred medium for a couple decades, but there is a need for faster secure communication. Free Space Optical Communication is an alternate wireless communication system which uses optics to create a link. It utilizes low-power and converts an analog signal into digital pulses which are transmitted across space to a receiver. Its only caveat is its vulnerability under atmospheric obstacles. The goal of this project is to create a free space optical …

Pv Mppt Water Pump Controller, Jacob R. Lamkin

Electrical Engineering

The intention of this project is to create a low cost way to extract the maximum useful power from a PV module to power a water pump. This approach will yield maximum financial and technical accessibility for end users. The project was successful in powering a water pump from a PV module as desired, and the microcontroller driven control circuitry was capable of finding and maintaining operation at the maximum power point of the PV module. Due to the low performance of the buck converter used in this project, this approach was not as efficient as desired and would require …

Waste Gasification, Glyn D. Lewis, Nash Taylor, Nicholas L. Ordonez, David S. Mccallum

Mechanical Engineering

This document summarizes the work the IGT Team has conducted on the topic of waste to energy gasification over the Cal Poly Winter, Spring, and Fall quarters of 2019. The project is being carried out by four Cal Poly Mechanical Engineering students: Nash Taylor, Glyn Lewis, David McCallum, and Nicholas Ordonez and the sponsor of this project is Tod duBois. The team’s original goal was to successfully create a system that compiles residential solid waste on a small scale, gasifies it, and measures the typical syngas outputs, so that the team may assess the viability of gasification of household waste …

Deployable Cover For Cubesat Fuv Imager, Edwin J. Rainville, Patrick J. Rainville, Jeff Wagner

Mechanical Engineering

The goal is to develop a deployable cover for a far ultraviolet imager cube satellite that will be used to map the earth’s auroras in the ionosphere. The deployable cover is used to protect the Far Ultra-Violet (FUV) sensor and lenses, house two mirrors which are used to filter unwanted light and expose optics when deployed. The deployable cover consists of a door, an actuator, a lockout mechanism, and an “open position” indicator. This project also includes designing a fixture for testing the optical alignment of the deployable cover after launch and during orbital conditions. The subassembly is required to …

Model Block Press Design, Ben Todd Van Hamersveld, Chester Wong, Alexander Wing-Jon Giannousis

Mechanical Engineering

This project’s goal is to redesign the Center for Vocational Building Technology (CVBT) BP9 earth block press, which makes 1/3 scale compressed earth blocks to build demonstration model homes in Thailand. The full-scale block press, the BP6, provides a sustainable and affordable technique for constructing habitable homes in Thailand. The BP9 serves as a tool to inform the public of the advantages of human-powered earth block presses through demonstration. The BP9 press design has multiple problems: it is too expensive to manufacture, there is too much friction when used, it has several weak points due to users unintentionally applying excessive …

Tumble Bot, Alena Beyer, Blake Gonzales, Jensen Severance, Liam Chaffey

Mechanical Engineering

Passive locomotion is the ability for an object to move from one place to another by the means of the environment. In nature species such as tumbleweed, fox tails, plankton, and man o’ war jellyfish rely on passive modes of transportation for survival and are able to cross vast distances with little to no expenditure of their own energy. This document seeks to explore the feasibility of building a machine relies on the energy of Mars’ environment to explore the Martian surface.

The “Tensegrity Tumbleweed Locomotion” (nicknamed Tumble Bot) senior project was sponsored by NASA Jet Propulsion Laboratory (JPL). The …

Mad Jack Alpine Touring Model Design, Austin Gasbarra, Gillian Stargensky, Madeleine Mccool, Brannon Smudz

Mechanical Engineering

Skiing is a sport enjoyed by millions of people every year, yet ski boots are very uncomfortable and cost- prohibitive, resulting in a low conversion rate of first-time skiers to lifetime skiers. Additionally, Alpine Touring (AT) is seeing a surge in popularity as ski resorts become more expensive, but few companies are developing affordable products in this realm. Mad Jack Snow Sports has developed a product that they believe addresses some of the main issues associated with skiing, but they want to develop their product line further. The problem statement and scope state that the purpose of this project is …

Critical Radius Of Insulation, Maria N. Ambrose, Samuel J. Sayre, Travis W. Martin, Matt T. Sterling

Mechanical Engineering

The critical radius of insulation is a counterintuitive concept within the study of heat transfer. The theory states that adding insulation to a cylindrical or spherical object will increase the rate of heat loss rather than decrease it, if the radius (thickness) of the insulation is at its “critical” value. The Critical Radius of Insulation Senior Project is designed to demonstrate this phenomenon to Heat Transfer students via a portable apparatus. The concept will be demonstrated with a cylindrical object which is heated by way of a separate voltage source. Thermocouples will display the temperature of the cylinder while insulation …

Resource-Constrained Project Scheduling With Autonomous Learning Effects, Jordan M. Ticktin

Master's Theses

It's commonly assumed that experience leads to efficiency, yet this is largely unaccounted for in resource-constrained project scheduling. This thesis considers the idea that learning effects could allow selected activities to be completed within reduced time, if they're scheduled after activities where workers learn relevant skills. This paper computationally explores the effect of this autonomous, intra-project learning on optimal makespan and problem difficulty. A learning extension is proposed to the standard RCPSP scheduling problem. Multiple parameters are considered, including project size, learning frequency, and learning intensity. A test instance generator is developed to adapt the popular PSPLIB library of scheduling …

Performance Enhancement And Characterization Of An Electromagnetic Railgun, Paul M. Gilles

Master's Theses

Collision with orbital debris poses a serious threat to spacecraft and astronauts. Hypervelocity impacts resulting from collisions mean that objects with a mass less than 1g can cause mission-ending damage to spacecraft. A means of shielding spacecraft against collisions is necessary. A means of testing candidate shielding methods for their efficacy in mitigating hypervelocity impacts is therefore also necessary. Cal Poly’s Electromagnetic Railgun was designed with the goal of creating a laboratory system capable of simulating hypervelocity (≥ 3 km/s) impacts. Due to several factors, the system was not previously capable of high-velocity (≥ 1 km/s) tests. A deficient projectile …

Fiberglass Mat-Roll Carryover, Bryce Youngson, Aaliyah Ramos, Johann Cayaban, Tony Ledesma

Mechanical Engineering

The asphalt shingle is a type of roof shingle that uses asphalt for waterproofing. Its low cost and easy installation make it one of the most common roof covers in North America. General Aniline and Film (GAF) is one of the nation’s largest manufacturers of roofing materials and produces asphalt shingles at their Shafter, California manufacturing facility. To manufacture asphalt shingles, a base material of fiberglass passes through a series of processes that sequentially add asphalt, ceramic-coated mineral granules, and thermoplastic adhesive. The fiberglass base-material arrives at the manufacturing facility in large rolls that workers must periodically splice together in …

Process Improvement And Lift Design For The Installation Of A Metrology Machine Assembly, Dalt J. Lasell, James Mitchell O'Meara, Matthew Steensma

Industrial and Manufacturing Engineering

The objective is to work with Onto Innovations, a leading provider of semiconductor metrology and manufacturing solutions, to develop a system that safely installs a 250lb optics plate into the Atlas III: one of their metrology machines. Based in Milpitas, CA, Onto Innovations utilizes a variety of operations to create different products and assembles each product on site. The 250lb optics plates are WIP that are transferred between fixtures and the Atlas III using a combination of lifts and human workers. The WIP have long lead times, high tolerances, and large costs associated with their manufacturing process.

Onto Innovations identified …

Automation Of Data Analysis In Formula 1, Adam Joseph Mourad, Prescott Jeanne Delzell, Patrick Conner Mccabe

Industrial and Manufacturing Engineering

This paper explores economic solutions for Formula 1 racing companies who are interested in data visualization tools. The research was conducted on the current development of data gathering, data visualization, and data interpretation in Formula 1 racing. It was found that a large chunk of racing companies within the league needs an affordable, effective, and automated visualization tool for data interpretation. As data collection in Formula 1 arises, the need for faster and more powerful software increases. Racing companies profit off-brand exposure and the more a racing team wins, the more exposure they receive. The goal of the paper focuses …

The Impact Of Education On Career Growth In The Construction Industry, Luis F. Rodrigues

Construction Management

A construction management degree and an apprenticeship are the two educational routes for a career in the construction industry. There are divisions within the workforce that reflect these educational pathways. Ideally, an alternative education would allow individuals without access to a university education to develop their career from an entry level position. However, if education has a long-term career impact, then limiting factors on education are consequently limiting on career growth. In examining if there is a ceiling on career growth relative to educational backgrounds, both education and experience were identified as key variables. In the case study presented, the …

Interdisciplinary Studio Pavilion [Isp] 2019, Alex Beaubien

Construction Management

The Interdisciplinary Studio Pavilion 2019 was designed for students within architecture, architectural engineering, and construction management to be placed into eight interdisciplinary teams and design a pavilion that reflected the narrative for the Wine History Project of San Luis Obispo (the “WHP). Its curricula emphasized aesthetics; fabrication methods and techniques; ease of assembly, reassembly and transportability; and function. Deliverables for each team's structure focused on these curricula that required numerous design refinements and construction feasibility studies. This required each team member to contribute their respective knowledge about architecture, structural engineering, and construction to create a pavilion that fulfilled WHP’s goals. …

Interdisciplinary Studio Pavilion [Isp] 2019, Albert J. Gutierrez

Construction Management

Historically Cal Poly’s motto has been ‘Learn by Doing’ and the College of Architecture and Environmental Design (CAED) is one of the leading examples of this. Many students gain valuable hands-on and real-world experience through collaborative projects and assignments. Through this learn by doing philosophy and collaborative learning approach Cal Poly construction management, architecture and architectural engineering students worked together in 8 separate studio teams to design and construct a portable pavilion for the Wine History Project of San Luis Obispo County. Acting as a client they requested that we design a portable pavilion space that will be used to …

The Need For A Real Estate Development Capstone Course, Will Robert Kieckhefer

Construction Management

Cal Poly has extremely well-known programs in Construction Management, Business, Engineering, and Architecture. All of these programs have contributed multiple leaders to the building industry every year yet have neglected to integrate the different disciplines that overlap within the industry. The research the author has collected to support the need for a real estate development capstone course included in-person interviews, online research, personal experience, and team surveys. The research concluded the need for a real estate development capstone course that would integrate students from the school of Business, Architecture, and Construction Management. In order to build a successful project, all …

An Analysis Of Single Family Residences And Townhomes In Los Angeles As An Investment, Maggie Lai

Construction Management

Purchasing a home has long been one of the most important financial decisions and big purchases one makes in their life. However, recently rising market prices and a large influx of people moving to large cities, such as Los Angeles, has driven housing prices far beyond many people’s budgets. In fact, affordability is going down at such a rapid rate that currently only 30% of LA County residents actually own a home. Additionally, Los Angeles is currently ranked as the fourth most difficult market for first-time homebuyers to delve in to. Many LA County residents have decided against ever purchasing …