Engineering Commons^™

Soarnet, Deep Learning Thermal Detection For Free Flight, Jake T. Tallman

Master's Theses

Thermals are regions of rising hot air formed on the ground through the warming of the surface by the sun. Thermals are commonly used by birds and glider pilots to extend flight duration, increase cross-country distance, and conserve energy. This kind of powerless flight using natural sources of lift is called soaring. Once a thermal is encountered, the pilot flies in circles to keep within the thermal, so gaining altitude before flying off to the next thermal and towards the destination. A single thermal can net a pilot thousands of feet of elevation gain, however estimating thermal locations is not …

Reducing Vale's Memory Management Overhead Through Static Analysis, Theodore C. Watkins

Master's Theses

Vale is a multi-purpose programming language that focuses on guaranteeing memory safety with minimal effect on performance. To accomplish this, Vale utilizes a memory management system called Hybrid Generational Memory (HGM). HGM uses generational references to track the state of objects in memory, and static analysis to reduce memory management overhead at runtime. This thesis describes the program that performs static analysis on Vale source code during compilation, and analyzes its effect on the performance of Vale programs.

Design And Characterization Of Standard Cell Library Using Finfets, Phanindra Datta Sadhu

Master's Theses

The processors and digital circuits designed today contain billions of transistors on a small piece of silicon. As devices are becoming smaller, slimmer, faster, and more efficient, the transistors also have to keep up with the demands and needs of the daily user. Unfortunately, the CMOS technology has reached its limit and cannot be used to scale down due to the transistor's breakdown caused by short channel effects. An alternative solution to this is the FinFET transistor technology, where the gate of the transistor is a three dimensional fin that surrounds the transistor and prevents the breakdown caused by scaling …

Microfluidic Electrical Impedance Spectroscopy System Automation And Characterization, Keaton Frahmann

Master's Theses

In this work, a novel microfluidic cell culture platform capable of automated electrical impedance measurements and immunofluorescence and brightfield microscopy was developed for further in-vitro cellular research intended to optimize cell culture conditions. The microfluidic system design, fabrication, automation, and design verification testing are described. Electrical and optical measurements of the 16 parallel cell culture chambers were automated via a custom LabView interface. A proposed design change will enable gas diffusion, removing the need for an environmental enclosure and allow long-term cell culture experiments. This "lab on a chip" system miniaturizes and automates experiments improving testing throughput and accuracy while …

Development Of A Portable Low-Moisture Food Pasteurization Device Using Rf Heating, Eric Jason Ohata

Master's Theses

Bacterial presence in low-moisture foods such as flour, cereals, baby formula, and spices, have become a concern due to sanitizing challenges. The food industry currently focuses on wet food sanitation as opposed to low-moisture foods because of bacteria’s inability to reproduce in low water activity media. Traditionally, food processing RF heating pasteurizes in mass quantities while an equivalent consumer device does not exist the market today. A consumer product would help eliminate food waste by providing an easy way to sanitize food and extend shelf life. The Portable Food Pasteurization (PFP) project is an interdisciplinary project involving the Electrical Engineering, …

Prediction Of In-Plane Stiffnesses And Thermomechanical Stresses In Cylindrical Composite Cross-Sections, Bryson M. Chan

Master's Theses

Accurate mechanical analysis of composite structures is necessary for the prediction of laminate behavior. Cylindrical composite tubes are a mainstay in many structural applications. The fundamental design of circular composite cross-sections necessitates the development of a comprehensive composite lamination theory. A new analytical method is developed to characterize the behavior of thin-walled composite cylindrical tubes using a modified plate theory. A generated numerical solver can predict properties such as axial stiffness, bending stiffness, layer stresses, and layer strains in composite tubes subjected to combined mechanical loading and thermal effects. The model accounts for the curvature by transforming and translating the …

An Artificial Neural Network For Bankruptcy Prediction, Walter D. Magdefrau

Master's Theses

Assessing the financial health of organizations remains a topic of great interest to economists, financial institutions, and invested stakeholders. For more than a century, research into financial distress has focused primarily on traditional applications of statistical analysis; however, modern advances in computational efficiency have created a significant opportunity for more sophisticated approaches. This thesis investigates the application of artificial intelligence on company bankruptcy prediction. The proposed neural network model is evaluated using the Polish Companies Bankruptcy dataset and yields a 5-year prediction accuracy of 96.5% and an AUC (area under receiver operating characteristic curve) measure of 92.4%.

A Power System-Based Iot Network For Remote Sensing Applications, Dominic Gaiero

Master's Theses

Cities around the world are facing increasingly significant challenges, including rapid urbanization, resource management, and environmental threats. In California for example, wildfires present an ever-growing threat that gravely harms people, destroys communities, and causes billions of dollars in damages. The task of addressing these environmental threats and many other challenges is greatly aided with widespread data collection and real-time inference. However, as IoT networks scale and require more energy for near-data analytics, the IoT endpoints require more power and complexity, limiting their deployment. Additionally, deploying endpoints in remote locations creates further challenges with higher reliability and communication constraints. In this …

Analytical, Numerical, And Computational Methods To Analyze The Time To Empty Open, Closed, And Variable-Topped Inverted Bottles, Callen Schwefler

Master's Theses

Recent unexpected experimental observations of the emptying of inverted bottles with perforations has generated interest in modeling and simulation of this phenomenon. It was observed that as a perforation, i.e., a small hole at the "top" of the inverted bottle, is added and enlarged, the overall emptying time first increases to a maximum value and then decreases until it reaches a lower limit. The change in emptying time is associated with a transition from jetting, where only water exits the neck, to glugging, a competition between air and water flows at the neck of the bottle.

This paper develops analytical …

Perishable Food Waste Reduction Through Technological Implementation At The Retail Level Of The Food Supply Chain, Cassandra Harriman

Master's Theses

Food waste has become a disaster of global proportion that the world can no longer turn a blind eye to. This paper aims to reduce food waste at the retail level of the food supply chain by recommending and quantifying the effects of current technology that can be implemented in traditional supermarkets. This research recommends that retailers implement electronic shelf labels in stores and employ dynamic pricing of perishable products, leading to reduction of food waste. No prior research had considered the primary goal of reducing food waste while preserving retailer profit through technological implementation. This paper quantifies the effects …

Dependencyvis: Helping Developers Visualize Software Dependency Information, Nathan Lui

Master's Theses

The use of dependencies have been increasing in popularity over the past decade, especially as package managers such as JavaScript's npm has made getting these packages a simple command to run. However, while incidents such as the left-pad incident has increased awareness of how vulnerable relying on these packages are, there is still some work to be done when it comes to getting developers to take the extra research step to determine if a package is up to standards. Finding metrics of different packages and comparing them is always a difficult and time consuming task, especially since potential vulnerabilities are …

Direct Drive Solar Panel Control Circuit, Marcorios Bekheit

Physics

A control circuit is built for insulated solar electric cookers (ISEC). Power delivery and temperature safety are the focus. Using a maximum power point tracking (MPPT) algorithm, Arduino Nano, voltage and current sensors, and a buck converter, the solar panel’s output power was maximized for a direct load heat resistor with 3.5Ω for a range of solar intensities. Using a resistance temperature detector, a temperature sensor is built for safety shutoff.

Automation, Annunciation, And Emergency Safety Shutdown Of A Laboratory Microgrid Using A Real-Time Automation Controller (Rtac), Do Vo

Master's Theses

Over the last decade, microgrid deployments throughout the world have increased. In 2019, a record number of 546 microgrids were installed in the United States [1]. This trend continues upward to combat extreme weather conditions and power shortages throughout the country. To better equip students with the necessary skillsets and knowledge to advance in the microgrid field, Cal Poly San Luis Obispo's Electrical Engineering Department and the Power Energy Institute have invested resources to develop a laboratory microgrid.

This thesis sets to improve the laboratory microgrid's existing automation using the Schweitzer Engineering Laboratory SEL-3530 Real-time Automation Controller (RTAC). The improved …

Fluid Powered Vehicle Challenge: Team Soulenoid Cycle, Kellen Muir Giuliani, Jordan David Kochavi, Cayla Renee Quinn, Martin Reyes

Mechanical Engineering

The National Fluid Power Association is a trade association that unifies customers and manufacturers within the hydraulics industry. Extending their partnership to universities, the annual Fluid Powered Vehicle Competition challenges college teams to design, build, and test a fluid-powered vehicle with the goal of educating students about the hydraulics industry and building career connections. Soulenoid Cycle produced the next iteration of Cal Poly’s fluid powered vehicle for the 2021 competition.

This report summarizes research, ideation, component selection, initial and final design, manufacturing, and competition results conducted by Soulenoid Cycle. Relevant research includes successful current and past vehicles, the operation of …

Knee Angles After Crosstalk Correction With Principal Component Analysis In Gait And Cycling, Jordan Skaro, Scott J. Hazelwood, Stephen M. Klisch

Biomedical Engineering

Principal component analysis (PCA) has been used as a post-hoc method for reducing knee crosstalk errors during gait analysis. PCA minimizes correlations between flexion–extension (FE), abduction–adduction (AA), and internal–external rotation (IE) angles. However, previous studies have not considered PCA for exercises involving knee flexion angles that are greater than those typically experienced during gait. Thus, the goal of this study was to investigate using PCA to correct for crosstalk during one exercise (i.e., cycling) that involves relatively high flexion angles. Fifteen participants were tested in gait and cycling using a motion analysis system. Uncorrected FE, AA and IE angles were …

Standardizing Patient Generated Sleep And Step Data For Evidation Health, Jade Desmet, Monroe Erle, Jamie Cullen

Industrial and Manufacturing Engineering

Since medical data has gone digital there has been a lack of standardization among wearable devices for managing the data. Evidation Health is a company that collects biometric data from a wide variety of wearable devices through their app, Achievement. Evidation is built upon a foundation of user privacy and control over permissioned health data. This project is in partnership with them, focusing on creating a standard data model and ETL tool for sleep and step data across the wearable devices Fitbit, Apple Watch, and Oura Ring. There is not yet a successful standardization for this health data, and the …

Market Analysis Of Virtual Estimating For Reconstruction, William Robert Spencer

Construction Management

Reconstruction is the sector of construction that focuses on fixing fire, mold, and water damage to properties. Typically these are covered by insurance companies and the cost of these are determined through an insurance estimate using Xactimate. These insurance estimates are typically performed through visiting the site a few times by both the insurance company and the reconstruction company. Each of them will typically put together an estimate based on normal photos and then compare the estimates and then pay out the homeowner. This paper will examine the market interest in California for using virtual tours and expert insurance estimators …

Journeyman International: Canopy Life School, Housing & Training Complex In Kenya, Spencer P. Mishky

Construction Management

The purpose of this project was to provide a master plan for a primary school complex in a rural village in Migori County, Kenya. This facility aims to eliminate any issues for students growing up in the area. The master plan includes a primary school, housing accommodations, a training center, and a dining hall to cultivate success through all stages of these children’s lives. The project is headed by a non-profit organization, Journeyman International in conjunction with Canopy Life International and Take Heart Africa. The project was interdisciplinary involving a construction manager, an architect, and two architectural engineers all working …

International Sustainability Trends In Construction And Potential Applications In The American Market, Dante De Mayo

Construction Management

The construction industry evolves everyday as it attempts to stay up to date on current technologies, meet the needs of consumers, and take action on the ever-pressing topic of sustainability. Sustainability is one of the main ways the industry continues to advance. The United States is one of the world leaders in sustainable construction, however with limited research and restrained interest there is only so much progress that can be made when solely relying on domestic resources. By studying and collaborating with foreign construction institutions, the American construction industry has the potential to improve its sustainability performance significantly. By performing …

Cm Member Of Slocoe Peace Conference Center Feasibility Study, Jackson Reynolds

Construction Management

This paper describes the parking design and estimate portion of a whole feasibility study conducted by an interdisciplinary team. The interdisciplinary team consisted of three senior undergraduate industrial engineering students, and one senior undergraduate construction management student. This feasibility study was conducted for the San Luis Obispo County Office of Education (SLOCOE) to determine if it is feasible to construct a new, 400-person conference center on a site in San Luis Obispo, CA. The complete study includes analyses of the following topics: economic, utilities, traffic/road, approval from Chumash Tribe, social/historical, climate, geological, vegetation and wildlife, noise and pollution, parking, mandatory …

Neural Network For Monitoring Infant Feeding Process In The Smartbottle Device, Jiajun Guan

Master's Theses

To research the relationship between Childhood obesity and infant feeding patterns, the Electrical Engineering Department at California Polytechnic State University has designed a SmartBottle device attaching to the bottom of a baby bottle to monitor the infant feeding process. This project mainly focuses on the software and firmware design, as well as the neural network design of the SmartBottle device. The SmartBottle device is designed to identify infant feeding activities and to record related data for overweight and obesity research on children. This device includes a 6-dimensional inertial sensor that contains a 3-axis digital accelerometer and a 3-axis digital gyroscope. …

Study Of Fragility Functions For Assessing Damage To Water Pipe Networks Caused By Earthquake Loading, Dylan Joseph Merlo

Master's Theses

The performance of water lifelines during seismic events is an area of ongoing research. In this study we evaluate eight (8) different seismic events and the impact that ground shaking and ground deformations had on water pipeline systems. The overall goal of this work is to provide municipalities and utility providers with tools for mitigating the consequences of seismic hazards on water lifeline systems by analyzing the accuracy of damage estimation models. Three (3) different repair rate models are evaluated using data collected from the seismic events and compared to observed repair rate data. Results are analyzed to examine the …

Design Of An Ultra-Wideband Frequency-Modulated Continuous Wave Short Range Radar System For Extending Independent Living, Toai-Chi Nguyen

Master's Theses

Falls in the disabled and elderly people have been a cause of concern as they can be immobilized by the fall and have no way to contact others and seek assistance. The proposed frequency modulated continuous wave (FMCW) short range radar (SRR) system, which uses ultra-wideband (UWB) signals can provide immediate assistance by monitoring and detecting fall events. The unique characteristics of this system allow for a frequency-based modulation system to carry out triangulation and sense the location of the fall through the usage of a continuous chirp signal that linearly sweeps frequency. This project focuses on the development, design …

Field Evaluation Of Non-Contact Flow Measurement Device - Pid, Jack Evans, Stuart Styles

BioResource and Agricultural Engineering

The Irrigation Training and Research Center (ITRC) has analyzed the data from several non-contact volumetric flow meter models under various conditions. This testing was done with support from technical services contracts with the California Department of Water Resources (DWR) and the United States Bureau of Reclamation (USBR).

Field Evaluation Of Non-Contact Flow Measurement Devices - Gcid, Jack Evans, Stuart Styles

BioResource and Agricultural Engineering

The Irrigation Training and Research Center (ITRC) has analyzed the data from several non-contact volumetric flow meter models under various conditions. This testing was done with support from technical services contracts with the California Department of Water Resources (DWR) and the United States Bureau of Reclamation (USBR).

Field Evaluation Of Non-Contact Flow Measurement Device - Bcid, Jack Evans, Stuart Styles

BioResource and Agricultural Engineering

The Irrigation Training and Research Center (ITRC) is currently testing several non-contact volumetric flow meter models under their technical services contracts with the California Department of Water Resources (DWR) and the United States Bureau of Reclamation (USBR). In April 2020, a Sommer RQ-30A non-contact flow meter was installed at Banta Carbona Irrigation Districts (BCID) Main Canal approximately 180 ft downstream of the discharge from Pumping Plant 1. The meter was mounted at midspan along a footbridge that crosses the throat of an ITRC designed subcritical contraction structure (see Figure 1). An existing SonTek Acoustic Doppler Flow Meter (ADFM) was installed …

Pomegranate: Procedural 3d Tree Creation Via User-Defined L-Systems, Jeremy Berchtold

Computer Science and Software Engineering

Pomegranate creates procedural 3D trees based on a user-specified template. The template supports randomness and allows users to generate an entire forest of unique trees from a single template. The output trees are a single closed mesh without intersecting geometry (with the exception of leaves). Additionally, the output contains a skeletal rig used for animating the trees. Pomegranate produces textured trees that can use either a realistic or stylized look, as well as supporting different mesh densities for games or film. Since this project uses a procedural workflow, artists can quickly create and make edits to their trees. This increase …

Half-Barrel Planter Mover, Mihir Shah, Natalie Lewis, Mason James Hughes

Mechanical Engineering

A device for transporting heavy barrel planters is needed. Barrel planters are wooden wine barrels that have been cut in half along the circumference. They are used to store and grow a variety of plants. As such, they can contain more than 300 pounds of soil. The products currently on the market are not designed for such heavy planters, are cost prohibitive, and do not take advantage of the tapered design of a wine barrel half. A solution is needed that is durable, easy to use, and low cost. This final design report will show the steps used to find …

Fsae Chassis Hardpoint Optimization, Christopher Soohoo, Ethan Vallivero, Dwarak Reddy

Mechanical Engineering

Our team has been tasked with optimizing hardpoints for the Cal Poly Racing team. Hardpoints are the locations on the chassis of a car that are designed to carry both internal and external loads, they are the areas where the engine and suspension connect to the chassis. These points are subject to torsion, shear, bending and pull-out loads. Cal Poly Racing needs more thoroughly analyzed individualized hardpoints that are optimized for weight, strength and specific stiffness, so they can reduce the overall weight and improve the race times of the vehicle while maintaining their strength and stiffness standards. Our team …

Controller Modeling And Stability Analysis Of Multiple Input Single Output Dc-Dc Converter, Astha Adhikari

Master's Theses

This thesis entails the stability analysis of the Multiple Input Single Output (MISO) DC-DC converter developed for the DC House Project at Cal Poly. A frequency domain control system model of the MISO converter was designed and constructed using MATLAB Simulink. Transfer functions were derived and modeled for each stage of the converter to best fit the converter circuit system used in the original MISO circuit. Stability metrics such as overshoot, undershoot, rise time, phase margin and gain margin were measured to evaluate and analyze the stability of the converter. These metrics were measured with the original model including the …