Engineering Commons^™

Construction Of Modular Concrete Footings For Use In Cal Poly’S High Bay Laboratory, Tyler W. Giddens

Construction Management

This project-based senior project had the end goal of creating two concrete modular foundations that can be used in the High Bay Laboratory for testing procedures. The concrete modular blocks are 6’ long by 3’ wide, and 1.5’ tall. The foundations each held 100 embeds. Each embed serves as an anchor point for various attachments for testing purposes. This was an interdisciplinary project amongst two CM students and one ARCE student. The ARCE student was responsible for the design of the blocks, encompassing the formwork and the rebar. The CM students were responsible for estimating, scheduling, and the construction of …

Potassium And Sodium Sensing Isfet Device And Array, Liam Stephen Hayes

Electrical Engineering

The use of Ion-Sensitive Field Effect Transistors (ISFETs) as a means of testing a person’s potassium concentration in real-time has broad applications in the consumer space. An avid runner could use such a device to keep track of their hydration and salt levels. A hospital could use it for patients who require around-the-clock remote monitoring, and a variation of ISFETs are currently being used as continuous glucose monitors for diabetes patients. While ISFETs are not a new development in the field of microelectronics, their use as wearable devices has recently become relevant. The goal of this project is primarily to …

An Inexpensive Maximum Power Point Tracking System For An Insulated Solar Electric Cooker Using An Off-The-Shelf Buck Converter, Andrew A. Perez

Physics

A specialized control circuit using an off-the-shelf buck converter is built for an Insulated Solar Electric Cooker (ISEC). Cost and efficient power delivery are the focus. An ISEC is synonymous to a direct load heat resistor, allowing a specific maximum power point tracking (MPPT) algorithm and fewer components. Only a microcontroller, voltage sensor, and digital-to-analog converter are used with the buck converter to maximize the power delivered by a 100W solar panel for the 3.3Ω load.

A Study Of Pressure Probe Response In Steady And Unsteady Flows, Michael T. Charonnat

Master's Theses

The objective of this thesis is two-fold: to analyze the directional calibration of a 3-hole probe in steady flow and to develop a method for the interpretation of measurements recorded with a novel, fast-response Pitot-type probe in unsteady, turbulent flow. Calibration data for the 3-hole probe’s two side ports was taken in the steady, non-turbulent region of a free jet and was evaluated for symmetry. In addition, data that was recorded using one side port in two independent calibration runs was compared to study repeatability. Misalignment was found between the nominally symmetric data sets, which may be the result of …

Analysis Of Current And Future Flood Hazard In The Sacramento-San Joaquin Delta, Nicholas L. Mcguire

Master's Theses

The primary motivation of this study is to estimate the current and future flood hazard throughout the Sacramento-San Joaquin Delta in the context of sea-level rise. I also analyzed the effects of storm surge and river flow on extreme events to better understand how these events originate and vary spatially and in time. To address this goal, I combined digital water level records (primarily 1983-present) with archival data collected by the California Department of Water Resources (1929-1983) to reevaluate flood hazard in the Delta and investigate the possible sensitivity of the region different sea-level rise projections. Available archival records from …

Design And Analysis Of A Discrete, Pcb-Level Low-Power, Microwave Cross-Coupled Differential Lc Voltage-Controlled Oscillator, Pavin Singh Virdee

Master's Theses

Radio Frequency (RF) and Microwave devices are typically implemented in Integrated Circuit (IC) form to minimize parasitics, increase precision and tolerances, and minimize size. Although IC fabrication for students and independent engineers is cost-prohibitive, an abundance of low-cost, easily accessible printed circuit board (PCB) and electronic component manufacturers allows affordable PCB fabrication.

While nearly all microwave voltage-controlled oscillator (VCO) designs are IC-based, this study presents a discrete PCB-level cross-coupled, differential LC VCO to demonstrate this more affordable and accessible approach. This thesis presents a 65 mW, discrete component VCO PCB with industry-comparable RF performance. A phase noise of -103.7 dBc/Hz …

Smart Spine Tape: Active Wearable Posture Monitoring For Prevention Of Low Back Pain And Injury, Samuel J. Borda

Master's Theses

Back pain and injury are a global health issue and are a leading cause of work and activity absence. Prevention would not only save those affected from the burden of pain and discomfort, but would also save people from loss of over 290 million workdays annually and save the healthcare system billions of dollars in expenses per year. Successful research and development of a wearable technology capable of comprehensively monitoring spinal postures that are leading causes of back pain and injury can result in prevention of mild to severe back pain and injury for high-risk people. To accomplish this, the …

Utilizing Prefabrication In Order To Achieve Leed Credits, Phillip E. Waldman

Construction Management

This paper is a dissertation on the concept and benefits of utilizing panelization in construction to achieve LEED credits. Panelization is the process of prefabricating construction framing materials, such as walls, floors, and roof systems, to streamline and improve the construction process. This dissertation aims to examine: (1) how prefabrication can optimize construction through effective waste management (2) how prefabrication manufacturing plants are more efficient, cost-effective, and better for the environment with regard to material use and recycling than traditional construction methods (3) how prefabrication can be used to obtain LEED credit points for the Construction and Demolition Waste Management …

Typical Demolition Waste Of Tenant Improvement Projects: A Case Study, Gregory K. Jameson

Construction Management

Sustainable approaches to the waste generated in construction demolition have been on the rise over the past two decades. In this case study research project, the demolition waste of commercial tenant improvement projects from two separate companies across multiple projects was documented and analyzed. This case study was inspired by a motivation to gain a better understanding of what waste is typical in tenant improvement remodels, what is being done to repurpose this waste and what obstacles currently stand in the way of better waste management practices. After conducting extensive research and analysis of current waste trends in the construction …

Fabrication Of Lab-Scale Polymeric And Silicon Dioxide Nanoparticle-Enabled Thin Film Composite Reverse Osmosis Membranes For Potable Reuse Applications, Timothy J. Dinh

Master's Theses

Reverse osmosis (RO) is widely used for water reclamation and is one of the most feasible technologies for addressing water scarcity around the world. RO membrane fabrication procedures are continually being optimized and modified to enhance the treatment performance and efficacy of the RO process. A review of the existing literature published on membrane fabrication revealed that a detailed and reproducible methodology consistent among prior studies was not available. Therefore, the primary objective of this study was to utilize techniques from prior research to develop a reliable lab-scale membrane fabrication process for studying the potable reuse applications of TFC RO …

Pressure Disturbance Upstream Of The Boundary Layer Data System, Michelle S. Leclere

Master's Theses

The primary objective for this work was to evaluate the reliability of computational fluid dynamics (CFD) tools in the prediction of upstream surface pressure disturbance and pressure drag of various instrument excrescence shapes for a small aircraft flight test device called the Boundary Layer Data System (BLDS). Insights on pressure disturbance will serve as a guide for the placement of BLDS probes/sensors, and pressure drag can be used to ensure sufficient adhesive is used to install BLDS instrumentation. The Mach number for all CFD cases was 0.12 and the Reynolds number based on excrescence height varied from 4 x 10 …

Prefabrication And Modular Construction: Cm 214 Residential Construction Learning Module, Matthew V. Keeth

Construction Management

The residential construction industry in the United States has certainly stuck to the conventional methods of stick-built construction nationwide. What if there was a better way? This project seeks to educate future Construction Management students about a smarter, more efficient, and sustainable method of homebuilding: Modular Construction. Distinguishing the difference between prefabrication and modularization is a necessary standard. Prefabrication is defined as the process of manufacturing the essential structural components of a home at a factory off-site. The large scale structural components of a home are then transported to the jobsite for easy installation. In addition, Modular Construction is defined …

Process Support Building Savannah River Site, Victoria Zawacki

Fire Protection Engineering: Culminating Experience Project Reports

A report on the fire and life safety analysis of the Savannah River Site Process Support Building is required in order to receive a Master of Science in Fire Protection Engineering from the California Polytechnic State University, San Luis Obispo. The Process Support Building is a two-story office building that was first occupied in 2013, with a floor area of approximately 10,000 ft2. The building contains mainly personal offices, but also contains conference and turnover rooms, a Computer Simulation Room, an Observation Room, and a lunch area. The analysis includes both prescriptive and performance-based analysis.

The Process Support Building is …

Fire Protection And Life Safety Analysis Of A University Conference Center, Amanda Beck Larkin

Fire Protection Engineering: Culminating Experience Project Reports

This project report analyzes various aspects of fire protection and life safety design for a University Conference Center, for both prescriptive and performance-based designs. The University Conference Center is a ten-story, high-rise building comprised of various gathering spaces, ranging from small conference rooms to large assembly spaces with auditorium-style seating. The building has a large two-story podium with basement below, with a smaller floor plate, ten-story tower offset to one side.

In the prescriptive analysis, no deficiencies were noted in the water-based suppression or fire resistance analysis. The building construction type, height, area, number of stories, wall and structural ratings, …

Fire Protection Analysis Project – 9220 Zanzibar Lane Maple Grove, Mn, Brian Vandal

Fire Protection Engineering: Culminating Experience Project Reports

This report contains an analysis of the life safety and fire protection features of a four-story apartment building in Maple Grove, Minnesota. The report is a part of the final project intended to meet the requirements for the Culminating Experience of the California Polytechnic Master of Science Fire Protection Engineering Program.

The apartment building chosen for the analysis is a mixed-use four-story wood-framed structure. The first floor of this structure includes office space for building management, a meeting space, and various electrical and mechanical spaces as well as apartments. There are exit stairways on each end of the structure extending …

Warren Baker Center For Science And Mathematics- Fire Protection And Life Safety Analysis, Logan Honeycutt

Fire Protection Engineering: Culminating Experience Project Reports

This report covers an analysis of the fire protection features within the Warren Baker Center for Science and Mathematics Building. This document first discusses the prescriptive requirements for the building as determined by applicable code. The items to be discussed, as they relate to prescriptive requirements, include the means of egress and relatable components, fire resistive construction, fire alarm system, fire sprinkler system, and smoke control system. All components were analyzed and compared to each applicable code to assess whether these specific fire protection systems were designed correctly.

In addition to an analysis of the prescriptive measures in this facility, …

La Universal, Jose Emilio Salgado Florencia

Fire Protection Engineering: Culminating Experience Project Reports

The purpose of this project was to analyze and compare the existing fire protection systems in “LA UNIVERSAL” building to current applicable codes and standards. Both prescriptive based analysis and performance-based analyses were performed.

The prescriptive based analyses included analyzing the structural fire protection, fire suppression, fire alarm, and egress systems. There are many fire protection features that do not meet the requirements established by the NFPA standards. The fire alarm panel does not provide enough address for the required number of devices required in the building. Emergency lights do not provide the minimum illumination established in NFPA 101. The …

Prescriptive And Performance-Based Analysis Of Colorado Liberal Arts College, Victor Wight

Fire Protection Engineering: Culminating Experience Project Reports

This project consists of a prescriptive and performance-based analysis of an existing two-story college building. The building is located in downtown Colorado Springs, Colorado. Colorado Liberal Arts College is used for general education courses with the focus on creative fields such as dance, graphic design, and art. The building consists of classrooms, offices, an art gallery, dance studio, and a bookstore.

A prescriptive based design was completed using the code requirements laid out in the International Building Code (IBC) 2015 Edition and applicable National Fire Protection Association (NFPA) Codes. The prescriptive based analysis consisted of analyzing life safety and egress, …

Two-Storey Office Building, Colin Mallett

Fire Protection Engineering: Culminating Experience Project Reports

This FPE 596 culminating project report was developed to meet the requirements for completion of the Fire Protection Master’s Program at Cal Poly. The report is intended to provide a detailed understanding of fire and building code requirements as well as describe both prescriptive and performance based approaches to human behavior in fire scenarios, building evacuation strategies, egress design and tenability analysis. An overall determination will be made to evaluate if the building provides the expected levels of safety for building occupants from fire.

The office building #211 was designed and constructed to be compliant with the International Building Code …

Mount Sac Gym & Aquatics Center: Fire & Life Safety Report, Alex Hoeft

Fire Protection Engineering: Culminating Experience Project Reports

This report has been prepared to review and analyze the Fire and Life Safety status of the proposed Gym & Aquatics building at Mt. San Antonio College. This was done using two methods: prescriptive and performance based. The prescriptive section examines the explicitly code-mandated requirements for the building and the performance-based section examines implicit requirements for the building based on the goals presented in the Life Safety Code, NFPA 101.

The subject building is a 147,000 square foot, two-story, steel-framed athletics complex occupied primarily for assembly and business uses. The structure has an indoor and outdoor component with two gymnasiums …

Existing Multipurpose Assembly Building, Garrett Mitchell Pelton

Fire Protection Engineering: Culminating Experience Project Reports

This report contains the compliance and life safety review of a multi-purpose assembly use building located in Denver, Colorado. The analysis contained within analyzes the prescriptive requirements of the structure as it stands today and then later reviews an alternative approach utilizing a performance based analysis. Due to this determination the building is evaluated as is and it is noted there are particular features that as a newly constructed building would require a different compliance approach.

This building was originally constructed in 1965 and has undergone two major additions. The East addition added the entire lower level in 1978 and …

Grange Insurance Audubon Center-Fire Protection Life Safety Report, Gabriel Levy

Fire Protection Engineering: Culminating Experience Project Reports

This technical approach narrative presents the intent and methodology of the Fire Protection and Life Safety systems for the Grange Insurance Audubon Center located at 505 W Whittier St. Columbus OH 43215. The primary goal of the structure is to provide life and property protection in a fire scenario while taking into account the costs of implementing the criterion and risks associated with the facility. This will be achieved through the appropriate application of requirements listed in the 2015 International Building Code (IBC) and the International Fire Code (IFC) as adopted by the City of Columbus, Ohio, and any reference …

Jack E Brown Chemical Engineering Building At Texas A&M University, Daniel Higdon

Fire Protection Engineering: Culminating Experience Project Reports

The Jack E Brown Chemical Engineering building at Texas A&M is located in College Station, TX. While this building is dedicated to chemical engineering, it serves many different departments as they use the lecture halls on the first floor. It was built and opened in 2004 and has 206,500 square feet with 7 stories. The building consists of multiple labs as well as study hall rooms, computer labs, offices, and the normal MEP/storage rooms. Jack E Brown building is one of the foremost buildings of the Texas A&M engineering quadrant and is further proof that Texas A&M desires to keep …

Solid Thermal Storage As An Energy Storage Device In Insulated Solar Electric Cookers: Thermal Modeling And Experiment, Michael Antonio Fernandez

Physics

The use of solid thermal storage (STS) as an energy storage device in insulated solar electric cookers (ISEC) was explored using a thermal simulation before retrofitting an existing cooker without energy storage and testing it under several conditions. STS sizing, material selection, and geometry were examined from both theoretical and practical perspectives and re-examined following experimental results. Characterization of the system’s thermal interfaces and methods to improve their thermal conductivities were investigated resulting in several performance enhancements to the system.

Barrier Knockdown Test Control System For The Cal Poly Kinesiology Department, Regina M. Chapuis

Computer Engineering

The goal of this project is to design and implement a new control system for the LEDs and buttons on an existing Barrier Knockdown setup in the Cal Poly Kinesiology department. The Barrier Knockdown test is a testing apparatus in which subjects knock down a series of mechanical barriers in one of three patterns. The computer system times their reaction and movement time, and the test as a whole provides students with data to study the phenomenon of Contextual Interference. This system was previously controlled by an old computer setup that ultimately crashed. This project recreates the logic and user …

The Poly Rover Project, Eric Lei, Alla Alamsi, Neil Patel, Diego Ramos

Computer Engineering

The Polyver Project is an idea born from the curiosity of a few students who wondered what the interaction between a physical person and a rover as the host of random internet users would look like. It is also an experiment to enhance the exploration of real world sites in real time while also having the power of interaction.

The goal of the Polyver Project is to build the foundation for a system that can serve as the interface between the internet and a fleet of rovers. Each rover is equipped with at least a camera, microphone, and a speaker …

Moon Rocker: Eva Sample Bag And Dispenser, Birk D. Smith, Albert J. Kasinski, Christian Clephan

Mechanical Engineering

NASA’s next mission to the moon (Artemis) requires a device to dispense bags for holding and collecting rock samples on the lunar surface. The device must be lightweight, easy to use with an astronaut suit, and capable of withstanding the moon’s harsh environment. Our team has designed and revised several prototype dispensers to accomplish this challenge. Through testing and observations made while building our structural prototype, changes were made to build a more durable and usable dispenser. This led to our verification prototype, which was constructed with a carbon fiber frame and aluminum, or 3D printed smaller components. After manufacturing …

Sunsation’S Solar Powered Picnic Table, Michelle M. Barnett, Christopher Barber, Casey Durham, David Mason

Mechanical Engineering

Team SunSation is an interdisciplinary senior design project group that was tasked with developing a semi-permanent seating area for Cal Poly's electrical engineering courtyard. The EE courtyard is populated with plastic folding tables and chairs that are slowly falling apart. Dale Dolan, the head of the EE department, requested that a table design be developed that incorporates the use of solar panels. The addition of the solar panels to the table would help promote clean renewable energy as well as provide shade to those sitting in the courtyard.

The solution that SunSation arrived at is broken up into mechanical/structural, electrical, …

8 Dof Quadrupedal Hopping Robot, Clayton T. Elwell, John Bennett, Tyler Mccue, Daniel Munic

Mechanical Engineering

The goal of our senior project was to fabricate an eight degree of freedom (DOF) prototypical quadrupedal robot, develop a controller than commands the quadruped to repeatedly jump 10 cm in the air, and fabricate a modular test stand to safely deploy our controller on the quadruped. The creation of a functional quadruped will bring attention to Dr. Siyuan Xing and Charlie Refvem’s research group, Cal Poly Legged Robots, and will give future Cal Poly undergraduate and graduate students a learning tool to explore dynamic control of biomimetic robotic systems.

Over the course of our senior project, we successfully manufactured …

Coil Quick (Rv Sewer Hose Compressor) Device, Arturo Guijosa-Ruiz, David M. Bourgoin

Mechanical Engineering

The purpose of this design project is to design, build, and test an RV sewer hose compactor device that can be used by the project sponsor and marketed to other RV owners. The goal of the RV sewer hose compactor device is to mechanically compress an RV sewer hose from its fully extended length to its fully compressed and storable state. Since a prototype device has already been developed, this project will aim to improve the prototype design to make it smaller, quicker, quieter, and more durable. Additionally, we improved the device to make it more user friendly and have …