Engineering Commons^™

Representativeness And Sensitivity Analysis Of Accident Tolerant Fuel Cladding Behavior In Reactivity-Initiated Accidents, Melissa Andrea Moreno

Nuclear Engineering ETDs

Accident Tolerant Fuels (ATFs) such as FeCrAl are being developed to enhance safety margins in light water reactors during transients like Reactivity Initiated Accidents (RIAs). This dissertation evaluates the accuracy and representativeness of TRACE thermal hydraulic models for predicting FeCrAl C36M cladding behavior under steady state and transient flow boiling conditions. Benchmarking against University of New Mexico separate effects experiments shows that TRACE reproduces key thermal trends but underpredicts cladding temperatures near CHF by approximately 25 to 30%. A calibrated uncertainty and global sensitivity analysis, using Sobol indices, demonstrates that CHF and cladding temperature variability are dominated by mass flux, …

Kinetic Study Of Oil–Water Separation In A Dual Port Inlet Cyclone Separator, Ikhwanul Qiram, Agung Nugroho

Journal of Mechanical Engineering Science and Technology (JMEST)

In this study, a Computational Fluid Dynamics method is used to investigate the oil–water separation kinetics in a dual-port inlet cyclone separator. This was achieved using the Reynolds Stress Model coupled to an Eulerian multiphase framework. Three Reynolds numbers were studied (Re = 1.41×10⁵, 1.94×10⁵ and 2.52×10⁵) to analyse the flow; axial velocity distribution, vortex stability, radial migration velocity and separation efficiency were examined individually. Results indicate that both the radial migration velocity (vᵣ) and separation probability (p_remove) grow with Reynolds number, especially for larger oil droplets (10–100 µm). The best condition concerned is that …

Statistical And Spectral Theory For Spatially Correlated Random Aperiodic Antenna Arrays, Thomas Edward Christian Jr

Electrical and Computer Engineering ETDs

Aperiodic phased arrays enable beam steering, interference suppression, and spectrum efficiency for 6G, radar, biomedical imaging, and distributed sensing. Minimum inter-element spacing and keep out zones induce spatial correlation, violating the i.i.d. element-position assumption behind classical probabilistic random array theory. This dissertation develops a unified probabilistic spectral framework for correlated (non-i.i.d.) arrays. Second moment power pattern analysis incorporates the pair-correlation function  and structure factor , recovering the i.i.d. limit when  and accommodating unequal excitations. Side lobe and main lobe fields deviate from Rayleigh/Exponential and are modeled by weighted Nakagami and Gamma-mixture distributions, parameterized via Monte Carlo. The blue noise spectral …

Millimeter-Wave Antenna Gain Enhancement Through Stacked Planar Substrates, Zachary Bergstedt

Electrical and Computer Engineering ETDs

This work presents a new wideband millimeter-wave (mmWave) and sub-terahertz antenna design with flexible directivity through the integration of stepped horn antennas and transverse substrate integrated waveguide (SIW) slots for radar and communication applications. The work gives a theoretical and analytical basis for this filter-inspired approach to improving bandwidth and directivity, and presents design and results for a standalone stepped horn, a Ka-band antenna with a solid stepped horn and SIW feed, and W-band antennas with empty SIW feeds and stepped horns manufactured out of multiple planar layers. The realized antennas show bandwidth up to 40% and gain up to …

Calibration Methodology, Diagnostic Performance, And Redesign Of The Current Monitors On The Z Machine At Sandia National Laboratories, Stacie Hernandez

Electrical and Computer Engineering ETDs

A proper evaluation of the current diagnostics fielded in the inner-MITL region of the Z facility in 3D simulation models had not been performed until now. The evaluation of the current monitors has brought insight to their performance in a new view that has led to discoveries. The B-dot probe was the current diagnostic-of-choice since before the refurbishment of the Z facility [1] and until the development of the Inductively Driven Transmission Line (IDTL) current diagnostic [2]. Experimental data has shown that the IDTL can produce cleaner signals and it is more robust than conventional B-dots. Simulation (modeled using COMSOL …

Hierarchical Safe Reinforcement-Learning Framework For Mission-Aware, Edge-Enabled Multi-Uav Iot Networks, Abee F. Alazzwi

Electrical and Computer Engineering ETDs

This Ph.D. dissertation presents a unified Hierarchical Safe Reinforcement Learning (HSRL) framework for mission-aware, edge-enabled multi-UAV Internet of Things (IoT) networks. The work addresses the need for autonomous aerial infrastructures capable of delivering low-latency communication, scalable edge computation, and provably safe operation in dynamic environments. The dissertation develops three primary contributions. First, it formulates longhorizon drone base station placement and load balancing as a strategic actor–critic learning problem, enabling proactive adaptation to spatiotemporal demand variations. Second, it introduces a mission-aware multi-agent reinforcement learning controller for coordinated mobility, sensing, and computation offloading under latency and energy constraints. Third, it integrates a …

Nuclear Deterrence: Enhancing The Mission Through Smart Factory Predictive Solutions, Jarrod Matthew Ronquillo

Chemical and Biological Engineering ETDs

To meet the stewardship and modernization initiatives set by the Department of Energy new technologies must enter the manufacturing facilities within the nuclear deterrent complex. Predictive solutions begin with collecting data. An equipment health monitoring device was created to streamline data collection and organization for equipment and processes. A predictive and process performance dashboard was developed for a deionized water system. The dashboard used Western Electric statistical process rules and a machine learning regression algorithm to predict when the resistivity would fall out of specification. Lastly, a remaining useful life calculation was developed for all equipment related to nuclear deterrent …

Technical Advancements In Single-Molecule Spectroscopy For High-Throughput Measurement Of Long-Time Dynamics, Quyen B. Le

Chemical and Biological Engineering ETDs

Single-molecule fluorescence spectroscopy is a powerful technique for resolving transient biomolecular dynamics and quantifying free energy landscapes, kinetics, and binding interactions. However, two fundamental limitations restrict its broader application: slow, labor-intensive data acquisition and the limited observation time imposed by fluorophore photobleaching. These limitations hinder its use in drug discovery and biomedical engineering applications that require both high-throughput and access to long-time dynamics. In this work, both challenges are addressed through technical advancements. First, a simple, generalizable approach is introduced to automate data acquisition, eliminating manual intervention during experiments. This increases the acquisition rate by more than an order of …

Classification Of Hif Detection In Nev Profile Using Wavelet Transform And Convolution Neural Network, Abdul Hafiz Kassim, Mohd Abdul Talib Mat Yusoh, Aster Smith Valentinie Wilson Nottelmarc, Ahmad Farid Abidin, Sim Sy Yi, Daw Saleh Sasi Mohammed

Turkish Journal of Electrical Engineering and Computer Sciences

High impedance faults (HIFs) present a critical challenge in power systems due to their subtle signal characteristics, which often remain undetected by conventional protection methods. These faults typically do not produce significant phase disturbances, making reliable detection difficult. However, analysis of the neutral-to-earth voltage (NEV) profile under fault conditions provides a promising alternative for fault identification. Existing approaches for detecting and classifying HIFs using NEV signals remain limited and may result in inaccurate maintenance decisions. This paper proposes a fault classification framework for multiple fault types, including HIF, three-phase fault, three-phase fault to ground, double line, double line to ground, …

Complex-Valued Convolutional Neural Network With Time-Frequency Representation For Electrocardiogram-Based Arrhythmia Detection, Kajeeth Kumar Gurusamy, Muthurajkumar Sannasy

Turkish Journal of Electrical Engineering and Computer Sciences

This research proposes an end-to-end procedure for arrhythmia detection based on electrocardiogram (ECG) signals using complex-valued convolutional neural network (CVCNN) incorporated with time-frequency representation. The proposed model leverages complex numbers to capture amplitude and phase information that enhances the ability of the model for detecting time-frequency variation in cardiac signals. First, signal preprocessing techniques---including normalization, wavelet denoising, and R-peak detection---are applied. Subsequently, the model extracts complex features from raw ECG data by employing the Hilbert transform to derive the analytic signal and the short-time Fourier transform (STFT) to generate a time–frequency representation. The proposed CVCNN framework effectively learns spatial-temporal features …

Accurate Diagnosis Of Diseases By A Novel Ai Pipeline Based On Feature Extraction, Feature Ranking, And Feature Selection From Medical Images, Tuğba Nur Bozkurt, Mehmet Emi̇n Yüksel

Turkish Journal of Electrical Engineering and Computer Sciences

The rapid growth of the global population has led to a substantial increase in the number of patients, while the availability of healthcare professionals has not expanded at a comparable rate. This imbalance highlights the urgent need for efficient and reliable computer-aided decision support systems that can reduce clinical workload while maintaining high diagnostic accuracy. In this study, a novel and systematically integrated artificial intelligence-based pipeline is proposed for medical image classification, combining statistical significance-driven feature ranking with evolutionary feature selection in a unified framework. The proposed pipeline consists of four sequential stages: feature extraction, ranking, selection, and classification. Features …

Adapting Independent Large-Scale Pretrained Models For Human Action Recognition, Selen Pehli̇van

Turkish Journal of Electrical Engineering and Computer Sciences

Transferring knowledge from large-scale, independently pretrained image and text models to video understanding requires addressing several challenges, including maintaining generalization capabilities of models, integrating them into multimodal architectures, and fine-tuning with temporal dynamics. This study evaluates the effectiveness of parameter-efficient fine-tuning (PEFT) techniques in transferring pretrained knowledge from two independent models for video action recognition within a simple, streamlined multimodal fusion pipeline. Specifically, we adapt CLIP as the text branch and DINOv2 as the image branch, keeping both backbones frozen to preserve their pretrained robustness, while introducing lightweight, task-specific modules to adapt and fuse the branches with temporal dynamics. A …

Adaptive Backstepping Nonsingular Fast Terminal Sliding Mode Control For Robotic Manipulators Based On Disturbance Observer, Xin Zhang, Xu Wang

Turkish Journal of Electrical Engineering and Computer Sciences

This paper presents an adaptive backstepping nonsingular fast terminal sliding mode controller integrated with a nonlinear disturbance observer to achieve precise trajectory tracking of robotic manipulators subject to model uncertainties and unknown time-varying disturbances. A dead-zone–based adaptive gain mechanism is introduced to dynamically adjust the control gain according to the deviation of the sliding surface, thereby enhancing robustness and reducing chattering. The proposed reaching law ensures fast, nonsingular, and adaptive convergence, suppressing high-frequency oscillations without compromising stability and the nonlinear disturbance observer enables real-time estimation and compensation of modeling errors, friction, and external disturbances for superior rejection. The semiglobal uniform …

Chaotic Artificial Bee Colony-Optimized Stacking Ensemble For Robust Multifault Diagnosis Of Wind Turbines, Veilraj Revathi, Solaimalai Jeyadevi, Madasamy Sudalaimani

Turkish Journal of Electrical Engineering and Computer Sciences

The complex electromechanical structure of wind turbines, along with harsh operating conditions, poses significant challenges for precise and robust fault diagnosis. To address this challenge, an ensemble multifault diagnostic framework based on an adaptive chaotic artificial bee colony (C-ABC)-optimized support vector machine (SVM) and gradient boosting machine (GBM) is proposed. In the proposed framework, data redundancy and overfitting are reduced through a two-stage hybrid filter-transformer-based feature reduction approach using ReliefF, followed by Principal Component Analysis. The chaos function of the proposed C-ABC maintains an adaptive balance between the exploration and exploitation phases, thereby preventing premature convergence, which is a common …

Liquid-Phase Chemical Melting Deposition For Anchored Nanoparticle–Nanofiber Architectures, Hiep Pham, Kiernan O'Boyle, Gracie Boyer, Jonghyun Park

Mechanical and Aerospace Engineering Faculty Research & Creative Works

We report chemical melting deposition (CMD), a manufacturing strategy designed to overcome the low mass loading and weak interfacial bonding inherent to vapor-based synthesis. Unlike conventional vapor routes, CMD leverages a transient liquid-phase transfer (TLPT) mechanism driven by the differential thermal degradation of carrier fibers to transfer and anchor nanoparticles directly onto target fibers. This process thermodynamically drives the wetting and interfacial fusion of nanoparticles, establishing a liquid-phase contact pathway that enables markedly higher active material loading. To validate the structural resilience of this fused architecture against extreme volumetric stress, we utilized lead oxide (PbO) as a model system, which …

Harmonic Response Analysis Of Asymmetric Double-Wishbone Suspension Systems For Amphibious Vehicle Stability, Harper K. Mccraw

Theses and Dissertations

Amphibious vehicles in the surf zone face severe hydrodynamic forcing, yet their internal suspension dynamics remain under-characterized. This research quantifies the non-linear dynamic response of an asymmetric double-wishbone suspension under regular wave impact. Using a physical model in a wave flume and a Qualisys motion-capture system, global rigid-body roll angles were processed through a decoupled kinematic numerical framework to isolate time-domain strut displacements. To evaluate stability, the data was transformed into the frequency domain to calculate Total Harmonic Distortion (THD). Results indicate that all test configurations exhibited significant non-linearity, primarily driven by mechanical clipping as struts reached their physical travel …

Exploring Ai-Driven Scaffolding For Critical Questioning In Argument Evaluation, Ebenezer A. Belete

UNLV Theses, Dissertations, Professional Papers, and Capstones

The fast-paced changes caused by generative AI (GenAI) innovations call for exploring the potential benefits of GenAI in empowering 21st-century pedagogical strategies. Previous studies in the field of argumentation have shown how students can benefit from using critical questions. However, scaffolding argument evaluation through custom GenAI using critical questions has not been systematically investigated. This study involved two components: (1) designing and determining the usability of a GPT-powered conversational assistant (CQMAA Conversational Assistant) and (2) testing its impact on participants' efficacy for argument evaluation and their acceptance of GenAI as a learning tool through a pretest–posttest experiment. A convergent mixed-methods …

A Near Linear-Phase Analog Frequency Sampling Filter Design Framework Using A Second-Order Trust-Region Optimization Technique, Edreese Basharyar

UNLV Theses, Dissertations, Professional Papers, and Capstones

Analog frequency sampling filters (FSFs) provide an efficient means of realizing finite impulse response (FIR)-like behavior in continuous-time systems, but their practical implementation is constrained by the requirement for perfect pole-zero cancellation along the imaginary axis. Because exact cancellation is physically unattainable due to component variations, ideal linear-phase Type 1 analog FSFs exhibit uncancelled poles that result in system instability. To address this limitation, this thesis introduces a near-linear-phase design framework for Type 1 analog FSFs that achieves both stability and design flexibility through the inclusion of a damping constant, ρ, which shifts the poles into the left half of …

Criticality Safety Evaluation To Address Potential Over Conservative Restrictions In 49 Cfr Fissile Materials – Exceptions, Avian Blumhorst

UNLV Theses, Dissertations, Professional Papers, and Capstones

The U. S. Department of Transportation’s (DOT) 49 CFR 173.453 Fissile Exceptions provide a regulatory classification that helps eliminate burdensome regulatory requirements. The current fissile exceptions are based on past technical basis reviews. These reviews may be overly conservative, and the final ruling potentially applied significant administrative over-conservatism. This thesis reviewed and presents several recommendations to the fissile exception criteria, as well as 49 CFR 173.453 section’s additions.

Using Monte Carlo N-Particle (MCNP) code version 6.3.0, several infinite sea mixtures and array systems were modeled for fissile isotopes 233U and 235U. The research demonstrated that for fissile exception (a) there …

An Optimization Method For Near-Linear Phase Analog Frequency Sampling Filter Design, Leonardo Ledesma

UNLV Theses, Dissertations, Professional Papers, and Capstones

Analog frequency sampling filters (FSFs) realize a desired frequency response by interpolating a frequency response through a set of harmonically related frequency samples from the filter’s frequency response and are magnitude and phase coefficients used in the filters transfer function. FSFs can be designed to have exact linear phase which makes the FSF attractive for many applications. A FSF’s system transfer function (STF) shows that the filter can be implemented by a series connection of a comb filter and a parallel array of resonators. However, the FSF requires that the zeros created by the comb filter cancel the imaginary axis …

Visual Interpretability Of Multimodal Tissue Perfusion Classification Using Grad-Cam And Saliency Maps, Metehan Zorluoglu

UNLV Theses, Dissertations, Professional Papers, and Capstones

Accurate identification of the tissue perfusion phase from hand images can aid doctors in decision-making with non-invasive techniques. The present study proposes a multimodal deep learning model for classifying the tissue perfusion phase using infrared, thermal, and visible spectrum images of the human hand. The proposed model consists of various preprocessing techniques such as manipulation, homography alignments, and masking. The significant contribution of this thesis is the interpretability analysis of deep learning models, achieved through the analysis of saliency maps and the Gradient-weighted Class Activation Mapping (Grad-CAM) methods. The purpose of this method is to find out how the convolutional …

Vegetated Canopy Heterogeneity Footprints In The Roughness Sublayer, Giulia Salmaso, Raul Bayoan Cal, Marc Calaf

Mechanical and Materials Engineering Faculty Publications and Presentations

Turbulent flows over horizontally homogeneous rough surfaces are categorized as rough‐wall boundary layer flows, while flows over homogeneous vegetated canopies are better described through a mixing‐layer analogy. At present, numerous studies have investigated canopy density as a transition mechanism between rough‐wall and mixing‐layer‐type flows. Yet, most considered canopies have been spatially homogeneous, with few exceptions investigating agricultural arrangements. However, most vegetated canopies are not homogeneously distributed, but instead contain gaps and spatial heterogeneities of different scales. In these cases, it remains unclear which are the dominant flow traits, and how spatial heterogeneity affects them. To help overcome these knowledge gaps, …

A Descriptive Analysis Of Plant Leaf Disease Detection Using Machine Learning And Deep Learning Models: A Systematic Review, Arzoo Chamoli, Anuj Kumar

Turkish Journal of Electrical Engineering and Computer Sciences

Plant leaf disease detection (PLDD) is a growing active research area with burgeoning practical applications across various sectors such as agricultural monitoring, food security, and environmental conservation. Accurate segmentation and classification of plant leaf diseases remains a key challenge in the field of plant leaf disease prediction. The challenge demands automated methods for the plant disease identification because it needs to develop better crop management systems, which will boost agricultural production. In this article, we provide a systematic review of various machine learning (ML) and deep learning (DL) methods extensively used for PLDD. The review strategy follows a formal protocol, …

Multiobjective Optimization Framework For Renewable Energy Iot Networks Balancing Security, Energy Efficiency, And Communication Reliability, Muhammad Hjouj Btoush, Ashraf S. Mashaleh, Amjad Gawanmeh

Turkish Journal of Electrical Engineering and Computer Sciences

The deployment of Internet of things (IoT) networks powered by renewable energy sources presents unique challenges in balancing security requirements, energy efficiency, and communication reliability. This paper presents a comprehensive multiobjective optimization framework for secure renewable energy IoT nodes that addresses fundamental trade-offs between these competing objectives. We develop a mathematical model incorporating energy harvesting dynamics, security protocols, and communication performance metrics across various environmental scenarios. The proposed framework employs a modified NSGA-II algorithm to identify Pareto-optimal configurations for different deployment contexts. Through extensive simulation analysis, we demonstrate that hybrid energy sources (solar-wind combinations) with lightweight security protocols achieve optimal …

Predictive Current Control Approach For Grid-Integrated Multifunctional Converter Under Source And Load Disturbances, Ravi Kumar Majji, Tirumalasetty Chiranjeevi, Chilukoti Varaha Narasimha Raja, Nagulapati Kiran

Turkish Journal of Electrical Engineering and Computer Sciences

This paper discusses and presents a model predictive control (MPC)-based predictive current control technique for a solar photovoltaic (PV)-integrated grid system during dynamic operation. This control technique employs extension pq (EPQ) theory to estimate reference currents and utilizes an MPC framework for tracking reference currents. Various MATLAB/Simulink simulations were conducted for solar PV generation (source disturbances) and dynamic loading. The results of the OPAL-RT OP4510 real-time simulation are also presented. A multifunctional grid-integrated converter (MFGC) integrates solar active power into the utility grid while achieving unity power factor, reactive power compensation, current balancing, and harmonic suppression. EPQ optimizes mathematical calculations, …

Cortical Bone Density And Thickness Assessment Of Intraradicular Sites In Adolescent Patients Using Cbct Imaging, Sara Endo

UNLV Theses, Dissertations, Professional Papers, and Capstones

Background: The indications for the use of cone beam computed tomography (CBCT) in orthodontics has grown since it was first introduced and dentists are discovering new ways that 3D images enhance diagnosis and treatment planning. Evaluating bone quality and quantity can be measured as bone density and thickness in CBCT imaging and is helpful for temporary anchorage device (TAD) placement in orthodontic treatment. TADs rely on primary stability and are commonly used in orthodontic treatment to increase anchorage and expand the limit that nonsurgical orthodontics can provide.

Objectives: This study aims to assess the bone thickness and density at different …

Machine Learning Assisted Development Of Al0.2cufemnni High Entropy Alloy Through Selective Laser Melting, Hareharen K Mr

Theses and Dissertations

High Entropy Alloys (HEAs) are an emerging class of advanced materials that have gained significant attention due to their exceptional mechanical strength, thermal stability, and structural performance. Unlike conventional alloys based on a single principal element, HEAs are composed of multiple elements in a near-equiatomic ratio. Despite these advantages, designing HEAs with tailored properties is difficult because of the enormous number of possible combinations and the limitations of traditional trial-and-error methods. To overcome these challenges, this study presents a machine learning (ML) based approach to accelerate the design and development of an HEA.

In this work, a newly designed composition, …

Machine Learning Approaches For Predicting Biochemical Oxygen Demand And Ammonium Nitrogen: A Decade-Long Weekly Field Study At A Full-Scale Water Resource Recovery Facility, Hoda Khoshvaght, Ratish Ramyad Permala, Amir Razmjou, Mehdi Khiadani

Research outputs 2022 to 2026

Unlike previous studies that rely on high-frequency (15-min or hourly) datasets, this study is among the first to use low-frequency (weekly) data to evaluate the performance of linear and nonlinear machine learning (ML) algorithms for predicting biochemical oxygen demand (BOD) and ammonium nitrogen (NH4⁺-N) in the primary and secondary treatment effluents from the Subiaco Water Resource Recovery Facility (WRRF) in Western Australia. Various feature selection methods, including filters, wrappers, and embedded methods, were employed to identify the most effective approach that achieves the highest model performance while enhancing computational efficiency. The results demonstrate that a reduced set of …

Model Based Control And Hil Verification Of An Integrated Battery Management System, Catalin Sabou

UNLV Theses, Dissertations, Professional Papers, and Capstones

The rapid advancement of electric vehicle technologies necessitates highly reliable Battery Management Systems (BMS); however, validating embedded supervisory logic presents a notable challenge. While physical pack testing is accurate, it is costly and hazardous for early stage software evaluation. This thesis presents the design, implementation, and rigorous validation of an integrated BMS developed for the Battery Workforce Challenge, bridging the gap between model based design and safe hardware execution. The core of this work is a model based supervisory controller, developed in MATLAB/Simulink and executed on an STM32G4 embedded target. To facilitate embedded validation while preserving a representative battery environment, …

Design And Uncertainty Methodology In High Efficiency Filtration Media Testing, Jeremy Andrei Adriano

Theses and Dissertations

Electrospun nanofiber media are being developed as potential alternatives to conventional HEPA filtration materials due to their small fiber diameters and tunable microstructures. To support future testing of these materials, the Small-Scale Test Stand (SSTS) at the Institute for Clean Energy Technology (ICET) requires modifications to ensure accurate and repeatable aerosol filtration measurements. Electrospun filters introduce challenges including fragile media structures and uncertain filtration efficiencies that may allow particle penetration to downstream instrumentation. This work evaluates adaptations to the SSTS design to support testing of electrospun filtration media. In addition, an uncertainty framework for aerosol measurements obtained using a Scanning …