Engineering Commons^™

Skip The Grid: Powering The Navajo And Hopi Reservations, Casey A. Nuti

Construction Management

Skip the Grid is an interdisciplinary service project targeted at providing essential off-grid power to families of the Navajo and surrounding sovereign nations. This year a group of twenty-three students and four faculty from California Polytechnic State University (Cal Poly) helped plan and execute the insulation of solar power and other essential amenities on the Navajo and Hopi reservations. Many families that live on the reservation are below the U.S. poverty  line and obtaining grid power can be extremely difficult given the rigorous permitting requirements as well as the remote location of many of their homes. This service project is …

Solar Charging Station For Construction Gang Boxes​, Scott J. Burfield

Construction Management

This senior project explores the feasibility of a solar-powered charging system that attaches to the top of a construction gang box or knack box. The purpose of the project is to provide a cleaner and more convenient way to charge tool batteries and small devices on construction sites. Adding on, it will reduce reliance on generators, extension cords, and temporary power setups by being supplemental support. Research included interviews with construction electricians, product selection, cost estimating, energy calculations, and an evaluation of constructability and project risks. The proposed design uses a 100-watt solar panel, a portable power station, and a …

Construction Of Lightly Reinforced Concrete Walls And Foundations For Fiber Reinforced Polymer Testing, Aidan D. Seed, Coulter Langmaid, Ryan R. Bousfield, Bennett B. Steiger

Construction Management

This paper details the construction of two cast-in-place concrete walls with attached footings, built to continue ongoing research into Fiber Reinforced Polymer (FRP) retrofitting conducted by California Polytechnic State University, San Luis Obispo, Architectural Engineering (ARCE) department. The project was located inside the College of Architecture and Environmental Design (CAED) High Bay testing facility and is part of a multi-year effort to evaluate FRP wrap as a seismic retrofitting option for lightly reinforced concrete walls dating to the pre-1980s. Formwork from the previous year's senior project was reused for this effort, and a two-phase pour was utilized and executed by …

Greek Row At Cal Poly: Addressing Student Housing, Neighborhood Conflict, And Town-Gown Relations, Christopher Linn Green

Construction Management

This study evaluates whether centralized Greek housing near Cal Poly could serve as a long-term planning solution for reducing neighborhood conflict, improving student housing opportunities, and creating a more organized environment for fraternity and sorority life. The research was developed in response to ongoing concerns in San Luis Obispo involving student housing pressure, fraternity activity in residential neighborhoods, and code enforcement challenges. Two surveys were used to gather stakeholder perspectives. One survey of Cal Poly students and one survey of individuals who work in San Luis Obispo. Student responses showed strong support for a centralized Greek Row, with most respondents …

U.S. Army Corps Of Engineers Information Session At California Polytechnic State University, Jack Durham Abernathy

Construction Management

This paper presents a detailed analysis of an information session coordinated by Jack Abernathy with the United States Army Corps of Engineers (USACE) on May 14, 2026, at California Polytechnic State University San Luis Obispo. An Army Corps of Engineers info session creates a critical step for undergraduates where they have a professional environment to network with industry professionals and explore unique career paths that may have not been previously considered. The presentation exposed attendees to the history of the Corps of Engineers, employee occupations, and USACE’s varying mission sets. A representative from the USACE Sacramento District brought forward professional …

Self-Healing Concrete In Compression With Crystalline Admixtures, Nathaniel Paul Warfield

Construction Management

The construction industry is steadily pursuing sustainable and regenerative materials that extend service life and reduce maintenance requirements. Self-healing concrete containing crystalline admixtures represents one such technology. This study evaluated the compressive strength performance of a commercially available high-strength concrete with and without a crystalline self-healing admixture. Three 6-inch by 12-inch cylinders were cast using Quikrete High Strength Concrete. One cylinder served as the control specimen, while two cylinders contained Penetron Admix at approximately 1% of cement weight. One admixture cylinder was intentionally cracked after 14 days to allow time for healing before testing. All specimens were tested in compression …

Understanding Cmu Construction Sequencing Through Scheduling Application, Tristan J. Roberson

Construction Management

Concrete Masonry Unit (CMU) wall systems are used very often in all types of construction including commercial and residential. With this said, the scheduling logic behind their installation can often be unclear for students and people new to the industry. The purpose of this project is to analyze CMU construction sequencing and demonstrate how it integrates within an overall project schedule. This study was conducted using interviews with industry professionals, review of CMU manufacturing processes, and development of a simplified Critical Path Method schedule in Microsoft Project. Information from CMU professionals regarding manufacturing processes and lead times were incorporated based …

Improving The California Boulevard Railroad Underpass: A Feasibility Study Of Persistent Barriers And Practical Improvement Strategies, Jacee D. Carpenter

Construction Management

The California Boulevard railroad underpass in San Luis Obispo has served as an informal pedestrian route for Cal Poly students since pedestrian access across the adjacent railroad tracks was restricted in 2009. Despite its frequent use, the underpass presents challenges related to lighting, drainage, surface conditions, and seasonal flooding that affect safety and accessibility. Previous studies documented these concerns and proposed improvement concepts; however, no significant physical improvements have been implemented. This project evaluates the factors contributing to the lack of improvements and examines practical strategies for enhancing the underpass within existing regulatory, environmental, and jurisdictional constraints. Methods included a …

Developing A Preparation Manual For The Asc Region 6 & 7 Reno Competition, Addyson Mae Demasters

Construction Management

The Associated Schools of Construction (ASC) Region 6 & 7 Competition is one of the most prestigious student construction management competitions in the United States. Success in the competition requires technical knowledge, effective communication, time management, and strategic preparation. The purpose of this senior project was to develop a comprehensive Competition Preparation Manual for future Cal Poly Construction Management students competing in the ASC Reno Competition. The manual was created through the collection and analysis of information from previous competitors, team captains, competition retrospectives, and the author's personal experience participating in ASC Reno competitions. Surveys were sent to students in …

Small-Scale Rainwater Harvesting: A Sustainable Practice For Single-Family Homes In Southern California, Azzah R. Bensrhir

Construction Management

Southern California is prone to drought and struggles with low water supplies. Los Angeles and San Diego County have enacted outdoor water regulations that aim to reduce the overall reliance on municipal and groundwater supplies. Rainwater harvesting (RWH) is a feasible way for single-family homeowners in Southern California to contribute to water conservation efforts. To determine the feasibility of installing, maintaining, and understanding overall challenges and costs of small-scale rainwater harvesting systems, four interviews were conducted with residents of Los Angeles and San Diego County who have owned and operated a RWH system for more than five years. The results …

Multiplexed Fabry-Pérot High-Temperature Sensing Based On Dispersive Microwave-Photonic Frequency-Time Domain Analysis, Ruimin Jie, Chen Zhu, Bohong Zhang, Koustav Dey, Jie Huang

Electrical and Computer Engineering Faculty Research & Creative Works

We propose and experimentally demonstrate a multiplexed high-temperature Fabry-Pérot (FP) fiber sensing system interrogated by dispersive microwave-photonic frequency-time domain analysis (DM-FTDA). In the proposed architecture, incoherent broadband probing light is modulated by radio-frequency (RF) signals and then reflected by a parallel network of hollow-core photonic crystal fiber FP (HCPCF-FP) sensors. A chirped fiber Bragg grating provides strong dispersion to map the composite FP spectral response into a well-defined microwave transfer function. Unlike conventional optical Fourier-domain multiplexing that requires deliberate cavity-length allocation, the proposed approach achieves multiplexing via delay-dominated discrimination. Distinct delay fibers are assigned to each sensor branch, and an …

Quantum And Conventional Informatics Studies Of Synthesis Energetics And Defect Formation In Nitride Crystal Epitaxy, Andrew Steven Messecar

Dissertations

Machine learning is a valuable approach for the processing and analysis of complex information. By estimating relationships from recorded data, machine learning methodologies can be effective strategies for pattern recognition, enabling investigations and technological applications based thereon. The potential for improved understanding of high-dimensional data has drawn interest towards machine learning from across the sciences, including the research and development of new and improved material systems. In the context of experimental materials research, much of the reported efforts to incorporate machine learning into conventional practice have been primarily focused on either the enhanced analysis of characterization experiment data or the …

Building Services Engineering May/June 2026

Building Services Engineering

No abstract provided.

Can Generative Ai Make Farming Decisions? Current Status And Future Pathways: A Case Study In Row Crop Production With Chatgpt, Nipuna Chamara, Yufeng Ge, Joe Luck, Yu Pan, Saleh Taghvaeian, Cory Walters, Christopher Proctor, Daran Rudnick, Daren Redfearn

Department of Agricultural and Biological Systems Engineering: Faculty Publications

The agricultural decision-making process is experience-based, knowledge-dependent, time-sensitive, complex, and driven by historical data. Planting, fertilization, irrigation, and chemigation are key categories in farm decision-making, and currently there is no one-shot decision-support tool that covers all these activities. Generative Artificial Intelligence (AI) models are more advanced than traditional machine learning and deep learning models. These models have been trained on vast amounts of data from the internet, allowing them to accept unstructured data in various forms and generate human-like text, solutions to problems, and scenario predictions. Given this capability, we became interested in exploring the potential of generative AI in …

Foundation For A Digital Beamforming System Using Software Defined Radio, Daniel Cruz Guerrero, Shiron Bendrihem, Benjamin Tucker

Electrical Engineering

This report demonstrates a basis for the foundation of a software-defined radio (SDR)-based digital beam forming system. Specifically, a discussion of time, frequency, and phase synchronization is had in the absence of costly hardware like an OctoClock. Furthermore, this report digs deep into the design process and device characterization of a 4-way Wilkinson Power Divider, which is a necessary hardware component for phase calibration. SDR synchronization and calibration are critical in any digital beamforming system.

Design And Characterization Of A Pulsed Electric Field Chamber For Microalgae Lysis, Connor Strutin

Electrical Engineering

Microalgae are a promising renewable source of biofuel due to their high lipid content and rapid growth rates; however, algae cells must be electroporated (lysed) to release these lipids. The system developed in this project applies short (40 μs–10 ms), high-intensity (up to 33 kV/cm) pulsed electric fields (PEF) across cell membranes to enable electroporation.

Our lab-scale PEF chamber generates uniform, high-intensity electric fields using parallel-plate electrodes with sub-millimeter spacing. The system is designed to efficiently lyse microalgae cells for lipid extraction and biofuel production.

Maximum Power Point Tracking For Photovoltaic Cells, Rodrigo Menchaca-Ramirez, Jesus Martinez, Steven Rodriguez

Electrical Engineering

Unlike an ideal DC Power Supply, a solar panel does not operate with linear I-V Characteristics. The voltage and current characteristics of a solar panel change based on irradiance, temperature, weather conditions, and load demand. Because of these factors, solar panels do not always operate at their Maximum Power Point, which can lead to significant power losses. Maximum Power Point Tracking is used to adjust the panel operating point so that more usable power can be delivered to the load.This project developed a Maximum Power Point Tracking system using an STM32 Nucleo-L4A6ZG microcontroller and an LT8705A DC-DC converter stage. The …

Design, Build, Fly 2026, Unique Barnes, Dante Black, Kyle Greiner, Gabriel Kern, Justin Mayer, Charles Olsen, Jack Quinn, Ben Randall, Tate Schurman, Mark Williams, Brendan Yarusso

Mechanical Engineering Senior Theses

This thesis follows the design, manufacturing, and testing of Santa Clara's 2026 AIM Design, Build, Fly Team. The project is built on one main system with multiple subsystems related to the payload and integration of payload. The main system is the Wings of Theseus which is a 5 ft span electric remote controlled plane designed to complete 4 four missions: rapid loading and unloading of payload, airworthiness, internal payload flight, and towed payload flight. Each of these missions is directly related to the aforementioned subsystems. The Wings of Theseus incorporated a rectangular wing with geometric twist as well as a …

Short Arc Angles-Only Initial Orbit Determination For Reliable Reacquisition Of Low Earth Orbit Objects, Isabella Rackemann

Master's Theses

Low Earth orbit (LEO) is becoming increasingly congested, furthering the need for accurate tracking and catalog maintenance. Initial orbit determination (IOD) is the first step in this process, providing a preliminary estimate of an object’s state given observations. When it comes to LEO optical observations, a large portion of them are inherently short in duration. Angles-only IOD methods struggle with this data, often producing highly inaccurate solutions that limit reacquisition capabilities. This study expands on prior short arc IOD research, testing seven classical and assumed circular orbit (ACO)-modified angles-only IOD algorithms on real LEO observational data spanning 0-4 degrees of …

Kinetic Sculpture For The San Luis Obispo Botanical Garden, Yotam Barr, Reynaldo Farias, Natalie Krueger, Priscilla Puei Ci Lam

General Engineering

Flower Power designed, fabricated, tested, and installed a wind-driven metal lavender and bee sculpture for the San Luis Obispo Botanical Garden Children's Garden. The project provides a colorful kinetic installation that complements the existing poppy sculpture while remaining child-safe, durable outdoors, manufacturable with campus resources, and low cost to the sponsor. The final sculpture consists of a steel main stem installed in a sleeve-style concrete foundation, three green branch clusters, independently rotating purple lavender bud assemblies, decorative leaves, and a bee. The sculpture was fabricated from steel tube, sheet metal, bearings, printed ASA components, paint, and foundation materials. The installed …

Mars Mini Rover Sample Retrieval Robotic Claw, Cami Chambers, Ani Lachikian, Alexa Ramirez, Alex Power

Mechanical Engineering

This project involves several key stakeholders, including the Poly1 Rover Club, Professor Rich Murray, and NASA’s Jet Propulsion Laboratory (JPL). The primary objective is to develop an improved robotic claw capable of retrieving sample tubes left by the Perseverance Rover on the Martian surface. In tackling this challenge, the design must account for the harsh Mars climate while integrating cameras and electrical components, durable structure, and a rotational component to the Mini-Rover claw without incorporating an additional motor, sample storage unit, structural aspects or unnecessary weight. The current Mini-Rover consists of a four-degree-of-freedom robotic arm with joints often referred to …

Sensory, Light, And Sound Box, Galilea Andrea Portillo, Hannah Elizabeth Henderson, Marcus Kiyoshi Kanenaga

Mechanical Engineering

The Sensory, Light, and Sound Box senior project outlined an adaptable, mobile sensory environment designed to improve cognitive and visual processing skills for students with Cerebral Visual Impairment (CVI) at the Oceano Education Center. Currently, the market lacks accessible solutions tailored to these non-verbal, low-mobility students, making traditional classrooms overwhelming. This project outlines the modification of an existing static layout into a functional, three-sided wooden over-bed frame that accommodates a standard hospital bed. Our team manufactured a structurally stable verification prototype under a $500 budget, integrating slow-closing outward-hinged walls for safety, dual Bluetooth speakers, and a synchronized LED projector that …

Cathy’S Catcher, Marlee Scott, Regen Worsley, Alessandra Valenzano, Aviv Ben Zeev

Mechanical Engineering

Deep-sea fishing presents significant challenges for individuals with upper-limb differences, particularly when using prosthetic devices that are not designed for recreational fishing activities. This project developed a custom prosthetic fishing rod attachment for a user who had lost her forearm and desired a safe, comfortable, and independent method of fishing. Through interviews with the sponsor and an iterative design process, a lightweight aluminum attachment was created to interface directly with the user's existing prosthetic quick-connect system.

The design process included concept generation, CAD modeling, rapid prototyping with 3D-printed models, manufacturing, and user-centered refinement. The final design consists of a welded …

Elevate Grill, Tanner Bachmann, Lance Anderson, Caden Huang, Jonathan Li, Brady Alexander

Mechanical Engineering

Santa Maria-style grills are a defining cooking tool of California’s Central Coast and are valued for their open fire cooking method and adjustable grate height. While this design provides direct control over cooking conditions, maintaining a consistent cooking temperature requires frequent manual adjustment of the grate position. This process relies heavily on operator experience and continuous attention, making temperature consistency difficult to maintain in a commercial kitchen environment. The Elevate Grill project was developed for Mike Ahrens and Wren Provisions to address this challenge while preserving the traditional Santa Maria grilling experience. The system uses temperature feedback from multiple thermocouples …

Stakblocks, Micah Satoshi Inoshita, Ava Rose Doerschlag, Cody J. Ellis, Zach M. Lawton, Fernando M. Nalin, Nicholas Humphrey, Aiden Reed Anderson, Sara Maya Suratkal

Mechanical Engineering

Researchers developing sustainable building materials from agricultural waste need a faster way to prototype and evaluate small-scale samples under controlled temperature and pressure before scaling to production. Sponsored by Professor Pete Schwartz of Cal Poly San Luis Obispo, whose work focuses on sustainable technology for developing communities, this project aims to create a prototype testing device for researchers studying agricultural-waste bricks, with the University of Malawi as a potential future testing partner. The final product is intended to inform improved future designs rather than serve as a production-ready device, ultimately supporting the development of affordable, sustainable building materials for communities …

Toro Cover For Bob Packer, Bailey Smolinski, Brandon Petty, Arturo Ramirez, Kathryn Proctor

Mechanical Engineering

Small pools, spas, and hot tubs are common in residential homes, yet small pool owners face persistent tradeoffs between critical features such as weight, ease of use, and appearance in pool covers currently available on the market. Most products optimize a single attribute at the expense of others. For example, solar covers are energy efficient but structurally weak, safety meshes are cost-saving but intensive to install, and retractable covers are automated but expensive. Beyond these tradeoffs, existing solutions often demand multiple people to install, take time and effort, occupy valuable deck space, and sacrifice the surrounding aesthetic. Therefore, small pool …

Foldable Transfer Platform, Toby Sagi, Ashton Heiati, Triton Johnson, Zachary Denis

Mechanical Engineering

The report details the design and results of a Hoyer lift to transfer patients between wheelchairs and our sponsor's, Beacon VTC Santa Maria, vans. The lift disassembles into 3 main pieces, allowing the lift to be stored in the back of the van. The lift uses a hydraulic actuator to rotate the boom. We handed over our project to Beacon VTC Santa Maria for use in their facility!

Package Access Platform, Tyler Connor Moyers, Austin Sien, Brooke Almaraz, Aiden Montano

Mechanical Engineering

This Final Design Review (FDR) presents the completed package access platform project following fabrication, assembly, and verification testing of the final prototype. The project focused on the development of an adjustable and modular access platform capable of adapting to varying workspace requirements while maintaining operator safety and structural stability. The finalized design incorporates adjustable platform dimensions, modular frame expansion, integrated OSHA-compliant handrailing, and adjustable support legs to accommodate uneven surfaces and changing operational needs.

Water Turbine Dynamometer For Low-Power Turbomachinery Testing, Carmen Alaichamy, Yosef Huynh Torres, Michael Duperly, Michael Thomas Duff

Mechanical Engineering

Students in ME 443: Introduction to Turbomachinery compete to design and build efficient small impulse turbines. The course lacks a standardized method to experimentally calculate turbine power output and mechanical efficiency from accurate measurements of torque and speed, for example. To support the learning goals of ME 443, a dedicated water-turbine dynamometer is needed to provide controlled hydraulic power, accurate mechanical and electrical measurements, and clear data for performance evaluation.

Our proposed system delivers a safe, repeatable, and educational testing environment that can be integrated into the Fluids Lab or used as a standalone instructional tool. Key stakeholders include Professor …

Me443 Turbine Timing System, Jacky Liang, Michael Ayman Habib, Julio Cesar Gutierrez Jr., Eric Tran

Mechanical Engineering

No abstract provided.