Engineering Commons^™

A Simple Design Algorithm For Synthesis Of Multilevel Combinational Networks, James H. Tracey

Electrical and Computer Engineering Faculty Research & Creative Works

An algorithm is presented for the synthesis of combinational networks with a constrained arrangement of ANDS, ORS, NANDS, NORS, and inverters. The algorithm is easily presented to students in an introductory logic design course and has considerable application in modern practical logic design. Many texts available for a first course in logic design give very limited practical guidance for synthesis of networks under constraints outlined here. It is suggested that the algorithm presented here be furnished as supplementary material in the introductory course. Copyright © 1968 by The Institute of Electrical and Electronics Engineers, Inc.

Recombination Statistics For Neutron Bombarded Silicon Transistors, M. C. Chow, J. L. Azarewiczt, C. A. Goben

Electrical and Computer Engineering Faculty Research & Creative Works

This paper presents a recombination statistical model for the neutron-induced base current component reported previously. The derivation was based on the following: 1) the current equation for the induced current component developed previously; 2) the Shockley-Read-Hall statistics for holes and electrons; and 3) the recombination statistics derived by Sah, Noyce and Shockley for sites in the bulk space-charge region. The recombination statistics model depends on the diffusion potential, the junction voltage, the activation energy, temperature, and the ratio of capture cross-sections for holes and electrons. The utility of such a recombination statistical model is illustrated by using measured parameters to …

Radiation And Annealing Characteristics Of Neutron Bombarded Silicon Transistors, L. S. Su, G. E. Gassner, C. A. Goben

Electrical and Computer Engineering Faculty Research & Creative Works

Operating a silicon planar epitaxial transistor in the inverse configuration allows one to demonstrate clearly the importance of the neutron-induced base current component and its degradation of the emitter efficiency, and, because of the much larger depletion layer, to compute a volume dependent damage constant applicable to all silicon p-n junctions. The importance of minimizing the absolute change versus relative change in radiation hardening studies is clearly illustrated. Surface effects were found to be significant for transistors mounted in gas-filled cans. The diffusion potential was predicted, on theoretical grounds, to vary with neutron fluence, and the theory was experimentally confirmed. …

Design Of Truncated Sequential Tests For Rapidly Fading Radar Targets, Norval D. Wallace

Electrical and Computer Engineering Faculty Research & Creative Works

Curves and equations are presented from which the exact performance of truncated sequential tests can be determined for one important case: the biased square-law detector for the detection of rapidly fading targets. The method of generating functions is used to derive probability distributions for sample size. It is shown how these probability distributions can be used to determine truncation errors and the effects of multiple-resolution elements. Sample calculations are performed to determine the effects of a particular truncation procedure. Copyright © 1968 by The Institute of Electrical and Electronics Engineers, Inc.

Electric Field Investigations And A Model For Electrical Liquid Spraying, Wallace E. Deshon, Ralph S. Carson

Electrical and Computer Engineering Faculty Research & Creative Works

The equation generally used for determining the electric field at the liquid tip in electrical spraying of liquids was originally derived for determining the electric field around a metal tip in the extraction of electrons from metals. In the present paper experimental data were taken at the instant of spraying to determine the validity of using this equation for liquid tips. the results indicate that the value of electric field given by this equation needs to be increased by about 20% in the normal range of operation. A model for the spraying mechanism of the liquid is also presented. © …

Transport Of ⁸⁵Sr And ¹³⁷Cs Under Induced Clay Suspensions, Purush Terkonda

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

“The purpose of this study was to evaluate the effect of induced clay suspensions on the transport of ⁸⁵Sr and ¹³⁷Cs in an aqueous environment.

An instrumented flume was used as a model river to simulate an environment typical of a slow-moving, unpolluted, turbid stream. Modified longitudinal dispersion relationships were used to describe the transport of radionuclides in turbid streams. Data were derived from instantaneous release of ⁸⁵Sr and ¹³⁷Cs with suspended Attapulgite and Kaolinite clays. Continuous release of ¹³⁷Cs with an Attapulgite clay suspension helped to establish uptake and transport characteristics for one environmental …

Australian Tractor Test Report No. 49 : Mccormick International 624, G H. Vasey, W. F. Baillie

Journal of the Department of Agriculture, Western Australia, Series 4

AUSTRALIAN TRACTOR TEST REPORT

No. 49 - McCORMICK INTERNATIONAL 624

A Novel Method For Solving The Uniform Distributed Network Analysis Problem, Robert C. Peirson, Edward C. Bertnolli

Electrical and Computer Engineering Faculty Research & Creative Works

An application of the Laplace transform method of Ogata to the solution of the uniform distributed network analysis problem is described. Copyright © 1968 by The Institute of Electrical and Electronics Engineers, Inc.

Fracture Of Hardened Cement Paste, Steven John Hanna

JTRP Technical Reports

No abstract provided.

A Simplified Procedure For Major Thoroughfares Planning In Small Urban Areas : Progress Report, David Kent French

JTRP Technical Reports

No abstract provided.

Scattering Parameter Measurements And Amplifier Design, Thomas J. Herrick

Masters Theses

"The scattering parameter formulation in describing the small-signal operation of an active two-port device is developed. The inherent advantages of measuring the scattering parameters at UHF frequencies and the clear insight into the design problem are demonstrated. Some of the practical difficulties in a typical design problem are also considered"--Abstract, page ii.

Engineering Properties Of Bloomington-Normal Subsoils, Rohn Dunseth Abbott

Masters Theses

"The glacial subsoils of the Bloomington-Normal, Illinois area have been analyzed with regard to their engineering properties. Several boring logs are included to illustrate the horizontal and vertical variability in soil units encountered and in the engineering properties of these soil units. The engineering properties of the two most common foundation soils, the Bloomington and Normal tills are compared and special consideration is given to evaluating the compressibility of these materials. Evidence is presented that indicates that the circumferential trimming of a highly preconsolidated soil containing stones can cause significant sample disturbance. Special sampling techniques which eliminate circumferential trimming yield …

The Design Of A Hybrid Computer System, James Joseph Becker

Masters Theses

"Three typical hybrid computers in industry and educational institutions are presented. The hybrid computer designed and built at the University of Missouri at Rolla consists of an SCC-650 digital computer, a TR-48 analog computer, and a hybrid interface. The interface permits the digital computer to control the modes of operation on the analog computer. There are also 9 multiple-pole relays on the interface that can be controlled by the digital computer. A 320 hold removable patchboard is included in the interface. There are 40 trunks lines from the analog computer that are present on the patchboard. The 4 digital-to-analog channels …

The Design Of A Tape Deck Controller, Frederick Harold Keeve

Masters Theses

"A controller was built to interface the SCC-650 general purpose digital computer and the Kennedy Model 1400R incremental write/continuous read tape unit. All logic design information, signal lists, and tape deck instructions are included"--Abstract, page ii.

Construction Time And Cost Control Using The Ibm Project Management System/360, James Donald Bailey

Masters Theses

"The object of this investigation was to determine the advantages or disadvantages involved in the use of the IBM Project Management system/360 as a time and cost control tool as compared to the methods presently used by construction contractors in the small to medium size range.

The methods used by three construction contractors were investigated in order to acquire a sample of methods presently used.

It was determined from the investigation that a number of advantages could be obtained which would provide better control of a construction project.

It was also decided that a detailed investigation concerning the cost of …

A Numerical (Matrix) Solution For The Vibration Frequencies And Modes Of A Nonuniform Rectangular Plate With Arbitrary Edge Conditions, F. David Utterback

Masters Theses

"The material presented in this thesis is designed to provide the practicing engineer with a practical, approximate method of solution for the increasingly important problem of plate vibrations. The technique presented herein is basically an application of the use of generalized coordinates to describe the elastic and inertial properties of a finite element representation of a nonuniform rectangular plate. The plate will be idealized by utilizing a modification of the grid work technique developed by Hrennifkoff as a lattice work of interconnecting beams. By employing the elastic displacements as generalized coordinates, the only required compatibility conditions are that the displacements …

The Numerical Solution Of Two-Dimensional Fluid Flow Problems, E. David Spong

Masters Theses

"A numerical solution method is developed for the solution of two-dimensional, irrotational and compressible fluid flow problems. The partial differential equation, in terms of the velocity potential, describing the flow is replaced by finite difference equations and the resulting matrix is solved by Gaussian elimination. The method is successfully applied to two subsonic flow problems: a 7.5⁰ wedge and a 6⁰ wedge inlet. The method becomes invalid, as expected, with the appearance of sonic velocity in the flow field. An investigation of the definition of the singularities is made. This indicates that the best agreement with the experimental results for …

Sufficiency Conditions For Constrained Optima, Cheng-Chun Huang

Masters Theses

"The sufficiency conditions for constrained optimization problems are derived through the use of Lagrangian functions and through the introduction of the new concept of "constrained total derivatives." The relations can be used with equality and/or inequality constraints. The sufficiency conditions derived earlier by Phipps were corrected in this work--Abstract, page ii.

Distillation Column Simulation And Control, Hsian T. Chao

Masters Theses

"A 5-component, 10-stage distillation column was simulated by PACTOLUS by use of the hybrid technique. It was found that the digital-analog simulator is completely satisfactory for solving unsteady-state multicomponent distillation problems. A feedforward controller for a distillation column was designed and tested. The effects of feedforward and feedback control on binary system distillation columns were compared by PACTOLUS. It was found that the liquid flow rates, the holdups as well as the number of stages are important factors in the design of a feedforward controller"--Abstract, page ii.

A Study Of Swirling Air Flow In A Converging Nozzle, Charles William Lineberry

Masters Theses

"A study was conducted to determine the behavior of swirling air flow in a converging nozzle. Special instrumentation was constructed to obtain radial traverses of the flow at four axial positions. the data collected consisted of velocity, static pressure, and stagnation temperature. The flow pattern demonstrated the Ranque-Hilsh effect and reversed axial flow in the core region. As the flow entered the nozzle, it had the characteristics of a free vortex. At the exit plane the characteristics were those of a forced vortex. The converging nozzle caused an increase in the magnitude of the axial velocity component"--Abstract, page ii.

An Experimental Method Of Determining The Thermal Accommodation Coefficients Of Metallic Surfaces, Raymond John Dethorne

Masters Theses

"In the free molecule regime, Knudsen number greater than 10, heat is transferred from a solid by radiation and conduction. The ability of a surface to emit radiant energy is governed by a surface property called emittance while the surface property which apparently regulates the amount of heat transferred by conduction is called the thermal accommodation coefficient. This thesis presents the results of an experimental investigation to determine a relationship between these two properties, emittance and thermal accommodation coefficient. A test apparatus was constructed to measure both the radiation and conduction contributions between two concentric cylinders. cylinders of aluminum and …

Compressive Creep Of Basic Refractories, Maurice E. Green

Masters Theses

"The microstructure and mineralogical composition of direct bonded, 50 wt.% magnesia - 50 wt.% chrome ore refractory compositions containing controlled additions of silica were correlated with their compressive creep behavior in the temperature range 1450⁰ to 1550⁰C under stresses of 100 to 175 psi. Steady state creep rates were determined from the linear regression of the steady state regions of deformation on time. Apparent activation energies and deformation flow characteristics were determined from the temperature and stress dependence of the steady state creep rates. Silica contents up to 3.5 wt.% increased the amount of direct intergranular bonding which decreased the …

Spacing Of Explosive Charges, Calvin J. Konya

Masters Theses

"It is generally believed that the spacing of simultaneously initiated collar primed multiple charges is not dependent on the charge length. The stresses generated by explosive charges have been assumed to propagate through a material in a cylindrical manner. this assumption implied that the stress generated in any plane along the charge diameter would have been uniform in magnitude and direction. A finite explosive velocity along with a conical stress wave causes the stresses near the collar to differ from those farther down the column. for this reason, the spacing of charges would be dependent on charge length. An experimental …

Thermal Runaway In Power Transistors, Jerry H. Lee

Masters Theses

"Considerable work has been done on the theory of thermal runaway and the relationship between transistor junction temperature and collector power dissipation. The first part of this thesis is a review of literature. An equation for the normalized junction temperature and its peak value is developed. From this equation, the junction temperature at the thermal runaway point for a given maximum power dissipation could be determined. The second part of this thesis is experimental. The author examined the thermal runaway points for eight different transistors in the basic common emitter class A circuit which operated under no signal DC conditions"--Abstract, …

Radiation And Annealing Characteristics In Neutron Bombarded Transistors Operated In The Inverse Configuration, Lo-Soun Su

Masters Theses

"When operating a silicon planar epitaxial transistor in the inverse configuration (i.e., with the emitter functioning as a collector and the collector functioning an emitter) the bulk space-charge volume of the new "emitter-base" junction is increased by a factor of 26.5 times that of the normal emitter-base junction. The carrier concentration in the new "emitter" is decreased by five orders of magnitude from that of the normal emitter, thus making it easier to investigate the effects of neutron radiation on the space-charge region and at the surface. Experiments using biasing of the new "emitter-base" junction during neutron radiation to change …

An Intragastric Ph And Motility Monitoring And Automatic Titration System, Barry Foster Maycock

Masters Theses

"Knowledge of the effects of prolonged states of weightlessness on the physiological activities of gastric motility and acid secretion will aid in the planning of future space flights, since aberrations in these activities could affect the performance of astronauts. Investigation of these activities requires monitoring of the pressure and pH in the stomach and titration of the gastric contents. Since previous methods and equipment used for performing these functions are inadequate for this investigation, the equipment whose design and operation are discussed in this thesis was developed. This equipment includes an ingestible sensor capsule which is tethered in the stomach, …

The Decomposition Of 5-Hydroxymethyl-2-Furaldehyde Under Gamma Irradiation, William George Bowles

Masters Theses

"An investigation into the effects of gamma irradiation decomposition of 5-hydroxymethyl-2-furaldehyde (HMF) revealed HMF to be resistant to radiation catalyzed decomposition. A 1.0 normal solution of HMF was irradiated at a dose rate of 4.1 x 10⁵ Rads/hr to a total dose of 8.2 x 10⁶ Rads from a 5000 Curie ⁶⁰Co source. a total of 31 per cent of the HMF decomposed in a zero order reaction, although it was found the HMF decomposed completely under cadmium shielded irradiation in a nuclear reactor with some neutrons present. The reaction rate constant was found to be 4.8 x 10⁻³ moles …

Fast Neutron Induced Resistivity Changes In Order-Disorder Fe₃Al, Bruce A. Betts

Masters Theses

"Resistivity measurements were made of ordered, disordered and intermediate states of order-disordered specimens of Fe₃Al while being irradiated by neutrons. All the specimens were irradiated at ambient temperature, approximately 35°C in a modified Bulk Shielding Swimming Pool type reactor. The ordered and near ordered specimens increased in resistivity indicating disordering whereas the disordered and near disordered specimens decreased in resistivity indicating an ordering process was occuring [sic]. By extrapolation, an equilibrium condition was determined and estimated at 130-135 micro-ohms-cm resistivity that would remain constant during irradiation because the ordering and disordering affects of neutron irradiation would be in equilibrium"--Abstract, page …

Instrumentation Of A Shock Tube Facility, James Everett West

Masters Theses

"The theory of schlieren and interferometer systems was described and related to studies of shock waves in a shock tube. An interferometer was procured and a schlieren system was modified for use with the UMR shock tube facility. The design and construction of a base for the systems and window assemblies for the shock tube comprised the major portion of the work on this project. A short series of tests were run to ascertain the compatibility of the instrumentation to the UMR shock tube facility. While no schlieren photograph of the shock wave was obtained, the system was shown to …

The Effect Of Prior Cold Work On The Pressure Welding Of Ferritic Nodular Iron, Ronald Morris Ledbetter

Masters Theses

"The purpose of this investigation was to determine the effect of prior cold work by swaging on the pressure welding of ferritic nodular iron. Test pressure welds were produced from continuously cast ferritic nodular iron in the as cast condition and with prior cold work of 20, 30, 40, and 50 per cent reductions in area. Welding pressures of 23,500 psi, 35,300 psi, and 47,100 psi were employed. All welds were made at interface temperatures of 2000°F. Welds made with the as cast material at high welding pressures possessed relatively low tensile strengths due to the creation of planes of …