Engineering Commons^™

A Study On The Lateral Placement Of Automobiles Due To Restrictions On Two-Lane Rural Highways, Warren Chip Woods

Masters Theses

"The driver of an isolated vehicle on a given section of highway, whether it is urban or rural, will choose a path on the pavement that offers the least resistance to driver effort and which to him seems safest. Lateral obstructions, such as retaining walls, trees, bridge abutments, ect., which may cause him to deviate from the desired path represent some degree of hazard to the driver and should be removed, if practicle. The purpose of this investigation was to determine any change in the lateral placement of automobiles due to side restrictions on rural two-way, two-lane highways. Phase one …

Measurement Of Turbulence In An Annular Jet, George Philip

Masters Theses

"An experimental investigation was conducted for an annular jet which consisted of a circular jet and a concentric wake. The annular air jet mixed with quiescent atmospheric air. The jet velocity was kept constant at 137.0 feet per second which corresponds to a Reynolds Number of 73,200. Using the technique of hot-wire anemometry, mean velocities, turbulence intensities and Reynolds stresses were measured in the longitudinal and lateral directions. Two distinct flow regimes, the free stream jet regime and the diffusing jet regime, are observed. In the free stream jet regime, higher turbulence intensity and shear stress occur in the inner …

An Analysis Of Single Wire Earth Return (Swer) System For Rural Electrification, Balwinder Singh Samra

Masters Theses

"The primary objective of this investigation was to determine the general applicability of Single Phase Earth Return(SWER) system for rural electrification where the load density is low, for example electrification of farms and small villages in emerging nations. The limitations of SWER system of distribution are many and it is necessary to make judicious use of such transmission. In this investigation the construction costs of transmission and distribution by SWER system is compared with single phase and three phase systems for loads of 25KVA and 50KVA. Phase converters are required to operate a three phase motor on a single phase …

Design And Test An Operational Amplifier Speed Transducer, Tung-Ming Huang

Masters Theses

"This thesis describes the design of an angular speed transducer. The purpose of this device is to provide a D.C. voltage which is proportional to the angular speed of a rotating shaft at any instant. The speed of the shaft is defined from a magnetic pickup monitoring a gear or similar device attached to the end of the shaft of a piece of rotating equipment. The signal from the magnetic pickup is modified and compared to a frequency generated in the feedback loop of the speed transducer and the error is sent to an integral type controller. The output of …

Analysis Of A Substitute For The Impact Damper To Damp Near-Resonant Mechanical Vibrations, Nguyen Khanh Van

Masters Theses

"This report investigates a substitute for the impact damper which, although highly effective in reducing vibration amplitudes of near-resonant mechanical systems, in operation causes often unacceptable intensive noise. The present damper consists of a piston free to move in a cylinder, at either end of which is a ball valve set to open at a preset pressure, and in the middle along its length an intake port. An approximate analytical study is made to determine the conditions for the existence of "noiseless periodic operation" of the damper, periodic operation without the occurence of impacts. This approach is based on the …

Structural Test And Analysis Of A Vierendeel Steel And Concrete Composite Girder, Melvin Crews Oestreich

Masters Theses

"The results of the structural load testing of a unique type of steel and concrete composite girder are described. The structural system, referred to as a composite Vierendeel girder, is a hybrid type which incorporates features of a castellated beam and a Vierendeel truss. The performance of the composite girder agreed reasonably well with calculated values based on section properties for a prismatic beam. Observations indicated web stiffeners were required on the stub beams to prevent premature failure of the system. Failure of the girder was due to concrete crushing over a stub web beam. Design considerations for a structural …

Development Of A Sampling System And Characterization Of Stormwater Runoff From A Small Urban Area, William Clark Ford

Masters Theses

"Increasing urbanization and the demand for high quality water have directed attention to the problem of combined sewer overflows, while recent research has demonstrated that stormwater alone, without the influence of sanitary sewage, carries a significant pollutional load. The purpose of this investigation was to determine the quality and pollutional contribution of stormwater runoff from a small urban area, with specific emphasis on the development of a suitable sampling and flow recording system, the characterization of runoff and the correlation of runoff quality with local environmental factors and storm characteristics. The system developed consisted of an automatic sampler capable of …

Characterization And Staged Lagoon Treatment Of Swine Feedlot Waste, Abraham H. Loudermilk Jr.

Masters Theses

"Feedlot pollution is developing into a serious problem because of the trend toward intensive farming techniques and the increasing number of animals in confinement feeding operations. The purpose of this study was to characterize swine waste collected under a slotted feeding floor using a water-carriage system, and to evaluate the treatment of this waste in a staged lagoon system consisting of an anaerobic, a dual anaerobic-aerobic, and an aerobic lagoon. A small feeding floor unit capable of maintaining 3 separate groups of animals, and a pilot 3-lagoon system were designed, constructed, and operated for a period of approximately 4 months. …

A Tensi-Volumetric Apparatus: Theory, Calibration, And Use In An Investigation Of The Oxygen Non-Stoichiometry Of Pure Batio₃, Glenn Jon Conger

Masters Theses

"The development of the tensi-volumetric apparatus has been traced to its current position of significance in studies relating to oxide non-stoichiometry. Components of the tensi-volumetric apparatus, especially the capacitance membrane manometer, were examined in detail as were the parameters affecting the performance of such an apparatus. Based on a careful consideration of components and performance, a tensi-volumetric apparatus has been designed, built, and its operation theoretically justified for its particular physical configuration. Results of existing studies of the oxygen non-stoichiometry of barium titanate have been used to predict its behavior during a tensi-volumetric study. Specific analytical procedures developed for use …

Managerial Appraisals - A Systems View, James Thomas Hatlan

Masters Theses

"In the past decade much has been written concerning the performance appraisal which can be defined as the systematic analysis of the individual with respect to his performance on the job. The appraisal's importance lies in the fact that its impact is felt in the areas of control, promotion, and managerial development all of which are essential for the progressive firm. This study is an attempt to offer something new and something different. The author offers a systematic study of industry in general with specific help from key corporations and utilities. His investigations encompass the three elements of appraising and …

Decimal-Base Binary Logic (Dbbl) Adders And Registers, James Oliver Bondi

Masters Theses

"This paper discusses a new type of base n adder and storage register. This new type of logic is called "n-base binary logic", or NBBL. The NBBL system is compared and contrasted with the Post base n system (a type of n-valued logic), the binary-coded base n system, and the straight binary system. The main purpose of this paper is to show that a decimal, or base 10, system can have some important inherent advantages over a binary system, such as greater daily operational efficiency. Furthermore, it is shown that a "decimal-base binary logic" system, or DBBL system, has inherent …

Experimental Studies Of Supporting Wire Disturbances In The Near Viscous Wakes Of Slender Supersonic Bodies, Kenneth Anthony Mirly

Masters Theses

"Wires have often been used as a means of mechanically supporting a model so that its wake will be relatively free of support interference. Such support systems have many advantages over stings and are less costly than magnetic suspension systems. Investigations into the disturbances caused by these supporting wires have been carried out with the use of a two-dimensional flat plate and a wire supported slender cone. The tests were conducted in the University of Missouri-Rolla axisymmetric, supersonic wind tunnel at Mach 3.15, and at a Reynolds number of 2.14 X 10⁶ per inch. Schlieren photography, pitot and static pressure …

High Pressure Water Jet Cutting Of Rock, Richard Lee Henry

Masters Theses

"Three experiments are described that investigate the impingement of high pressure water jets on rock. The effect of jet pressure, stand-off distance, and time of impact on penetration and specific energy of rock removal are determined on Berea sandstone, Georgia marble, and Missouri granite. Pressures range from 5,000 psi to 25,000 psi, stand-off distances from 2.0 inches to 4.0 inches and time from 0.1 seconds to 5.0 seconds. The nozzle diameter used was 0.023 inches. The effect of nozzle speed and number of passes over the same area on depth of cut and specific energy are investigated on the above …

Design Of A Torsional Vibration Machine, Prafulchandra Pragjibhai Desai

Masters Theses

"In this thesis the design of the major components of a torsional vibration machine is presented. The machine is a torsional vibration actuator which will deliver a mean output angular velocity with a superimposed harmonic component. This type of motion can be used to study the torsional vibration characteristics of models representing crankshafts, gear trains, torsional dampers, and other systems. The primary machine elements of the actuator are a power source, flywheel, and a Hooke's joint. The power source consists of a D.C. shunt motor and a drive transmission using 3 V-belts. Through the use of a Hooke's joint, approximate …

Equilibria Between Moo₂ And Liquid Molybdenum Oxide, Prakash Bakhru

Masters Theses

"The oxygen pressure over solid molybdenum dioxide in equilibrium with liquid molybdenum oxide was determined by transpiration and solid electrolytic galvanic cell methods at 950ºC and 900º, 950º and 1000ºC respectively. The results were compared to those expected from thermodynamic data on the Mo-O system. Possible reactions between MoO₂ and SiO₂ were studied at different oxygen pressures up to 1550ºC. No compound formation or solid solution between MoO₂ and SiO₂ was detected by x-ray diffraction techniques. The phase boundary between MoO₂ and liquid molybdenum oxide was checked by microscopic examination of quenched samples. Equilibration runs were carried out in silica …

Reconstruction Of Finite Duration Signals, John A. Stuller

Electrical and Computer Engineering Faculty Research & Creative Works

The Problem of Reconstructing a Finite-Duration Finite- Energy Signal that Has Been Band Limited and Sampled is Considered. an Interpolation Formula is Derived that, in Principle, Permits Perfect Signal Reconstruction in the Noiseless Case Provided Only that the Sampling Frequency Exceeds the Cutoff Frequency of the Band-Limiting Filter. the Degradation Introduced by Measurement Noise on the Samples is Evaluated. © 1972, IEEE. All Rights Reserved.

An Experimental And Numerical Study Of Elastic Strain Waves On The Center Line Of A 6061-T6 Aluminum Bar, J. L. Habberstad, K. G. Hoge, J. Earl Foster

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The elastic strain waves resulting from the impact of two 3/4-in-dia 6061-T6 aluminum bars are studied experimentally and analytically. Experimental data are obtained from strain gages on the center line and outer surface of the bar, located at various distances from the impact end of the bar. Experimental data are compared to numerical results obtained from integrating the exact equations of two-dimensional motion. In general, agreement between the numerical and experimental results is very good. © 1972 by ASME.

An Application Of Bubble Shape Theory To The Determination Of Air Transfer Through Adsorbed Surface Films, Robert A. Medrow

Mechanical and Aerospace Engineering Faculty Research & Creative Works

No abstract provided.

Magnetohydrodynamic Stability Of The Developing Laminar Flow In A Parallel-Plate Channel, T. S. Chen, T. E. Eaton

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Linear stability of the developing laminar flow of an electrically conducting, incompressible fluid in a parallel-plate channel under a transverse magnetic field is investigated. The case of small magnetic Reynolds numbers is treated. The developing flows whose stability characteristics are studied correspond to those induced by a uniform and a parabolic velocity distribution at the channel inlet. The stability of the fully developed Hartmann flow is also reexamined. Neutral stability curves and axial variations of the critical Reynolds number are presented for a range of Hartmann numbers between 0 and 4. It is found that for Hartmann numbers larger than …

Forming Of 7075-T6 Aluminum In High Pressure Environments, Richard L. Pendleton, Robert L. Davis

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Plates of 7075-T6 Aluminum have been folded along a major axis in pressure environments of atmospheric, 20,000 psi, and 40,000 psi. A finite element computer program is used to determine the stress state in the plates at various loads. Tension and compression tests conducted in pressure environments up to 70,000 psi were used to construct models using effective stress, effective strain, and pressure as parameters to predict the behavior of the material under various stress conditions. A prediction of the occurrence of fracture in the folded plate was possible using the computer results and the pressure dependent model. As better …

A Strain Energy Comparison Of Discrete Modeling For Vibrating Continuous Systems, S. K. Tolani, Richard Dale Rocke

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Lumped parameter models commonly used to describe continuous one-dimensional and Bernoulli-Elder beam vibration problems have been compared on the basis of maximum system, strain energy. The consistent mass matrix approach has been included in the comparison. Standard matrix techniques have been employed to mathematically obtain desired solutions. Closed form solutions and solutions via the models to Ike system strain energy were obtained for all systems in three dynamic states: Free vibrations, constant base acceleration, and half sine base acceleration. Behavior of the strain energy errors, in general, were found to be similar to those of the frequency root errors. © …

A State-Space Approach To Rlct Two-Port Transfer-Function Synthesis, Eddie R. Fowler, Rao Yarlagadda

Electrical and Computer Engineering Faculty Research & Creative Works

This paper presents an interesting procedure for the synthesis of an RLCT two-part transfer function. An RLC ladder, consisting of n reactive elements and two resistors, is derived by using a tridiagonal matrix developed by Navot. The entries in this matrix are expressed in terms of the element values of the ladder network. Two voltage drivers are introduced into the ladder network to obtain a desired short-circuit transfer-admittance function numerator degree, using the classical theorems on transmission zeros. If the numerator degree of the transfer function is i (i < n), then, in general, (i) ladder networks need to be derived. The final network, corresponding to this transfer function, is obtained by paralleling the ladder networks (with transformers if necessary). Extensions to general short-circuit transfer admittance, open-circuit transfer impedance, and voltage transfer functions are briefly discussed. © 1972, IEEE. All rights reserved.

Dissolution Potentials And Activation Energies Of Insb Single Crystals, Martin E. Straumanis, Lih Da Hu

Materials Science and Engineering Faculty Research & Creative Works

The rest (or corrosion) and dissolution potentials of InSb single crystals in HC1 were determined. There is no potential difference (within error limits) between the inverse {111} faces in pure HC1. A difference of up to 44 mV and more develops as soon as the InSb electrode is anodically dissolved. The potential becomes less noble in the sequence In{111}, {100}, {110}, Sb{111}. The Tafel relationship is observed over three decades of current density. With additions of FeCl3, FeCl2, K3Fe(CN)6, K4Fe(CN)6, H2C4H4O6 to 2N HC1, the anodic potentials of both inverse {111} faces are shifted to more active values; the e'H …

Comment On The Nature Of The Disaccommodation In Hcp Co-C Alloys, J. Keiser, Manfred Wuttig

Materials Science and Engineering Faculty Research & Creative Works

No abstract provided.

Pbo Transformation Induced By Water, Charles A. Sorrell

Materials Science and Engineering Faculty Research & Creative Works

No abstract provided.

Thermal Expansion Behavior Of Silicon At Low Temperatures, Jayant S. Shah, Martin E. Straumanis

Materials Science and Engineering Faculty Research & Creative Works

Lattice parameters, thermal expansion coefficients and Grüneisen parameters of silicon are determined by an X-Ray diffraction method in the temperature range of 180-40 K without the use of liquid gases. Thermal expansion of silicon becomes negative below 120 K which is discussed in terms of its lattice vibrations and crystal structure. © 1972.

Deformation And Fracture Of Concrete Under Uniaxial Impact Loading, Esteban Eulogio Miranda

Doctoral Dissertations

"Stress wave propagation and interaction in plain concrete leading up to spall fracture was investigated experimentally with a computer numerical analysis of the bar-geometry axial-impact loading. The critical normal fracture strain energy U and mechanical energy W criteria are proposed for the spatial and time dependence explanation of spallation in concrete. The energy criteria are special cases of a more generalized cumulative damage model of the form:....

Finite-difference analyses of the wave propagation and interactions in the split Hopkinson bar showed that early failure in brittle materials limits the application of the conventional method of analysis because equilibrium in the …

The Application Of Impact Dampers To Continuous Systems, Ranjit Kumar Roy

Doctoral Dissertations

"A study has been made of the application of impact dampers to two types of continuous systems, a simply supported and a clamped beam. Previous efforts have included the effect of impact dampers on single degree of freedom and other systems with finite numbers of degrees of freedom.

Experimental models were tested in the laboratory and finite element computer programs were developed to calculate response. Results from calculations agree favorably with experimental tests. Further, results from the first few natural modes also compare reasonably with data published on systems with finite number of degrees of freedom.

Curves are presented which …

Modal Truncation Of Substructures Used In Vibration Analysis, Suresh Kumar Tolani

Doctoral Dissertations

"The objective of this study is to describe in a unified manner a group of structural dynamics analyses using the substructures technique. An additional effort is to provide a consistent basis for the selection of substructure principal modes as required by this method. Substructure principal mode frequency roots and strain energy are two criteria evaluated for the selection of substructure principal modes. System eigenvalues and system strain energy are investigated for the comparison of results in the principal modes. System strain energy should provide more rational results since it is proportional to the stress times the strain in the system …

A Method For Generating Uts Assignments With An Iterative State Transition Algorithm, Dattatraya Govind Raj-Karne

Doctoral Dissertations

"There is a lack of systematic procedures that can be used to find uni-code totally sequential (UTS) assignments from a flow table description of an asynchronous sequential circuit. Presented here is an iterative internal state assignment method. This method consists of three algorithms. The first generates a minimum variable initial assignment from a flow table description. The second tests the validity of this assignment by constructing minimum length transition paths without crossover and the third augments this assignment by adding an internal state variable in the event that all transition paths cannot be constructed without crossover. The second and the …