Engineering Commons^™

Film Boiling Of Freon 113, Normal Pentane, Cyclopentane And Benzene From Cylindrical Surfaces At Moderate Pressures, G. J. Capone, Efton Park

Chemical and Biochemical Engineering Faculty Research & Creative Works

An investigation of film boiling heat transfer in saturated pools of liquid Freon 113, normal pentane, cyclopentane and benzene was conducted. The fluids were boiled from copper, cylindrical heat transfer surfaces 0.0762m (3 in) long, and 0.01397,0.01905 and 0.0254m (0.55,0.75 and 1.0 in) in diameter. The data covers a moderate range of pressures up to 1.67 (10)6 N/m2 (242.5 psia). The experimental data are compared with existing film boiling correlations. The existing film boiling correlations were found to be inadequate in predicting heat-transfer coefficients for the conditions of this investigation. © 1979.

Load And Resistance Factor Design Of Cold Formed Steel-Calibration Of The Design Provisions On Connections And Axially Loaded Compression Members, Wei-Wen Yu, Trinh-Ngoc Rang, Theodore V. Galambos

CCFSS Library (1939 - present)

No abstract provided.

Plasma Polymerization Of Tetrafluoroethylene. I. Inductive Radio Frequency Discharge, H. Yasuda, N. Morosoff, E. S. Brandt, C. N. Reilley

Chemistry Faculty Research & Creative Works

The plasma polymerization of tetrafluoroethylene in an inductively coupled radio frequency glow discharge, using a flow system, was studied. A simple long tube reactor, with the coupling coil placed at the middle of the tube and gas entrance and exit at the respective ends, was used. Deposition rates and the chemical nature of the polymer (as revealed by ESCA spectra and surface energy studies) are obtained as a function of location in the reactor tube with respect to the coupling coil and of applied energy per unit mass of tetrafluoroethylene (W/FM). It was found that a fluorine poor polymer, containing …

Load And Resistance Factor Design Of Cold-Formed Steel Study Of Design Formats And Safety Index Combined With Calibration Of The Aisi Formulas For Cold Work And Effective Design Width, Trinh-Ngoc Rang, Wei-Wen Yu, Theodore V. Galambos

CCFSS Library (1939 - present)

INTRODUCTION In the design of steel buildings, the "Allowable Stress Criteria" have long been used for the design of cold-formed steel structural members in the United States (1), Canada (2) and other countries (3). Even though the theoretical concepts of risk and reliability analyses have been available for some time (8-10) and the slgnlflcance of such concepts in structural safety and design is well recognized, the probabilistic method has not been explicitly adopted as a basis for the American design standard for steel structures. In view of the fact that the mathematical theory of probability, which has been so successfully …

Phase 1 Inspection Report: National Dam Safety Program. Missouri - Kansas City Basin. Binder Lake Dam, Cole County, Missouri, Hoskins-Western-Sonderegger, Inc. Consulting Engineers, Lincoln, Nebraska

Missouri Dam Safety Inspection Reports

This report presents the results of field inspection and evaluation of the Binder Lake Dam.

It was prepared under the National Program of Inspection of Non-Federal Dams.

This dam has been classified as unsafe, non-emergency by the St. Louis District as a result of the application of the following criteria:
1) Spillway will not pass the Probable Maximum Flood.
2) Overtopping could result in dam failure.
3) Dam failure significantly increases the hazard to loss of life downstream.

Load And Resistance Factor Design Of Cold Formed Steel-Calibrations Of The Design Provisions On Laterally Unbraced Beams And Beam-Columns, Wei-Wen Yu, Trinh-Ngoc Rang, Theodore V. Galambos

CCFSS Library (1939 - present)

No abstract provided.

Phase Equilibria In Aqueous Magnesium Chloride, Sulfate, Chromate And Phosphate Systems, Ladawan Urwongse

Doctoral Dissertations

"In the first part of the present study, which is presented in Paper I, solubility of MgO in aqueous HCl solutions at 23° ± 3°C was measured and combined with analyses of neat magnesium oxychloride cements to construct an equilibrium phase diagram for the system MgO-MgCl₂-H₂O. Invariant liquids in equilibrium with Mg(OH)₂ and 5Mg(OH)₂·MgCl₂·8H₂O (5.1.8), with 5·1·8 and 3Mg(OH)₂·MgCl₂·8H₂O (3·1·8), and with 3·1·8 and MgCl₂·6H₂O were located at 0.8 ± 0.2 MgO, 17.0 ±0.5 MgCl₂; at 1.0 …

Stress-Strain Properties Of Compacted Modified Memphis Loess, Danny Lloyd Kerns

Masters Theses

"A study was made of the stress-strain characteristics of compacted samples of a modified loessial soil obtained near Memphis, Tennessee. The study consisted of compacting samples at a constant water content and at unit weights of 92, 96 and 100 pounds per cubic foot (1470, 1540 and 1600 kg/m³). Triaxial tests were performed on unsaturated compacted specimens to obtain stress-strain-volume change data. These data were used to determine stress-dependent functions for tangent modulus and Poisson's ratio"--Abstract, page ii.

A Planning System For Research Management In A University Environment, Russell Lee Goldammer

Masters Theses

"The research project director at a college or university has few, if any, of the traditional management tools that are available for other forms of management, especially in performing the early, crucial stages of planning. This is particularly distressing since managing a program in this type of environment can be very difficult, due to bureaucratic red tape and interdepartmental concerns. The purpose here is to develop an aid for managers with these problems, for more effective research management in a university environment.

After developing a general model for a typical research project at a university, the Gasification Research On Wood …

Development Of Impervious Low Thermal Expansion Petalite Bodies, Suchinda Chotipanich

Masters Theses

"Impervious petalite bodies were formulated from petalite, lithium aluminosilicate frit and kaolin. Thermal expansion coefficients for selected bodies were less than 2 x 10⁻⁶ /°C(20 - 600 °C). Mineralogy and the reactions in systems containing petalite, lithium aluminosilicate frit and kaolin were observed. Silica-poor high quartz solid solution was found to be the reaction product formed from the reaction between frit and kaolin before conversion to ß-spodumene solid solution at higher temperatures. The crystallization of the ß-spodumene solid solution phases in this system did not occur at the same temperature resulting in variation in the size of the crystallites. The …

The Effects Of A Kinesthetic Training Program On The Acquisition Of Industrial Skills Among University Students, John V. Mockler

Dissertations and Theses @ UNI

Training workers for specific jobs is receiving much attention in industry. The demand for skilled workers is increasing constantly and as this happens newer and more efficient methods of training are sought In the psychomotor/sensory area. skills that appear to offer a wide amount of transferability are those dealing with fine sensitivity, manual dexterity, and coordination. Even though these skills lend themselves well to training, this area is somewhat deficient in current educational and training programs (Sjogren, 1977, p.23). Presently, on-the-job training is widely used for training workers in the actual tasks they will perform during their job.

The process …

Performance Theorems For The Resource Scheduling Functions Of A Multiprocessing System, George Arthur Nicol

Dissertations and Theses

In this dissertation, a multiprocess scheduling model is developed and a set of performance theorems is constructed for the set of scheduling functions associated with the model. Each theorem describes the conditions under which a scheduling function exhibits a particular type of performance.

A Study Of The Effect Of Vibration On The Residual Stresses In A Welded Fabricated Tube, Shantini Ratnathicam

Dissertations and Theses

In many instances the predominant factor contributing to structural failure in welded parts is the residual stress which exists before the part is put into service. In this investigation an attempt is made to study the changes in residual stresses caused by vibrational stress relief (VSR). VSR is a fairly new idea in stress relief and there is no substantial evidence of its success in reducing residual stresses. This thesis documents the residual stress distributions found in 5/16 inch thick, 22 inch diameter welded fabricated tubes after VSR.

An Instrument For Determination Of The Polarization Of Fluorescence, George Irwin Johnston

Dissertations and Theses

This thesis is concerned with the development of a compact, sensitive and reliable instrument for determination of the polarization of fluorescence of fluorescein tagged molecules in solution. The instrument as designed and constructed differs from others (2,3,4,5,6,8,9). The difference is that all of its optical system is aligned on a single axis. This was accomplished by the use of an ellipsoidal mirror positioned between the excitation source and the phototube fluorescence signal receiver. In addition, the excitation source, a 45 watt tungsten-iodide light was electronically regulated to control the intensity.

Two types of determinations were made to verify the performance …

Complete Elastic-Plastic Solution Around A Tensile Crack In Strain-Hardening Materials, Clancy Hatleberg

Mechanical Engineering ETDs

A complete elastic-plastic solution for both small and large scale yielding is found for the total stress field surrounding a tensile crack in an infinite sheet of strain-hardening materials under conditions of plane stress. The solution is based on the deformation theory of plasticity in conjunction with strain-hardening stress-strain relations, and is found by using the minimum of a modified complimentary energy principle coupled with a modified Ritz method. Numerical results are obtained for two approximate constitutive laws; a Ramberg-Osgood stress-strain relation and a modified Ramberg-Osgood stress-strain relation. Results indicate that the total stresses are discontinuous as the crack tip …

The Effect Of Volatile Fission Products On Fuel Motion In Nuclear Fuel Elements, Paul Sasa

Nuclear Engineering ETDs

Stringent licensing procedures for commercial nuclear reactor operation require an in-depth analysis of the phenomena associated with postulated reactor core overheating accidents. One aspect of nuclear reactor safety assessment is a prediction of fuel behavior associated with such postulated overheating events, which includes an assessment of the role of fission product inventory contained within irradiated fuel elements on fuel relocation potential. In general the gaseous fission product, such as Xenon and Krypton, have been considered the most likely candidates for fuel relocation due to gas dissolution from the fuel matrix and bubble expansion during fuel overheating; thus, such gaseous fission …

Real-Time Estimation Of Aerodynamic Coefficients By Means Of An Extended Kalman Filter, James Robert Kelsey

Electrical and Computer Engineering ETDs

A technique for estimation of the aerodynamic parameters of a flight vehicle from onboard measurements is presented.

An extended Kalman filter is used to extract the parameters in the presence of measurement noise and initial uncertainty of the parameter values. Computer generated data were used for the measurement information in lieu of actual flight data.

Several state models of varying complexity are studied in an attempt to find a model which yields adequate estimates while minimizing the required computation time.

Acuta Enews December 1978, Vol. 7, No. 12

ACUTA Newsletters

In This Issue

PRESIDENT'S MESSAGE

POTPOURRI

1979 ACUTA CONFERENCE ACTIVITIES QUESTIONNAIRE

MOUTH OF THE SOUTH

PARTY LINE

MOTOROLA

Ole Miss Engineer 1978

Ole Miss Engineer

No abstract provided.

Bulletin - December, 1978, Civil Aviation Medical Association

Browse all Civil Aviation Medical Association Newsletters

A six page newsletter of the Civil Aviation Medical Association. The newsletter provided news about civil aviation medicine and information related to the organization.

Energy Fact Sheet: Residential Solar Heating, Blaine F. Parker, Larry W. Turner

Agricultural Engineering Energy Series

Heating a residence and the domestic water supply with solar energy is technically feasible in Kentucky. However, it is not feasible to provide 100 percent of the heat requirements. Some backup system is needed for continuous heat during cloudy weather and the cold part of winter. Both passive and active solar heating systems are technically feasible.

The Evaluation Of Corrosion Inhibitors For Controlling Corrosion In Closed Paper Mill White Water Systems, Ifeanyi E. C. Okeke

Masters Theses

No abstract provided.

Low-Void Concrete Mixtures, Assaf S. Rahal, James H. Havens

Kentucky Transportation Center Research Report

The purpose of this study was to modify concrete mix-design formulas to supplant all water over and above that needed for hydration with a non-evaporable liquid material and(or) a super-water-reducer or plasticizer -- thus producing a low-void concrete. A water-cement ratio of 0.244 - 0.30 was presumed minimal for hydration of the cement. Several polymeric materials, asphalts, oils, and superplasticizers were used. Success was achieved with two latexes, one epoxy, and several superplasticizers. The use of these materials in concrete resulted in improved strength, reduction of air voids and permeability, and enhancement of resistance to corrosive chloride salts.

Principal Angle, Principal Azimuth, And Principal-Angle Ellipsometry Of Film-Substrate Systems, R. M.A. Azzam, A.-R. M. Zaghloul

Electrical Engineering Faculty Publications

When the film thickness is considered as a parameter, a system composed of a transparent film on an absorbing substrate (in a transparent ambient) is characterized by a range of principal angle ø¯_min ≤ ø¯ ≤ ø¯_max over which the associated principal azimuth ψ¯ varies between 0° and 90° (i.e., 0° ≤ ψ¯ ≤ 90°) and the reflection phase difference Δ assumes either one of the two values: +π/2 or −π/2. We determine the principal angle ø¯(d) and principal azimuth ψ¯(d) as functions of film thickness d for the vacuum-SiO₂-Si system at …

Propagation Of Partially Polarized Light Through Anisotropic Media With Or Without Depolarization: A Differential 4 × 4 Matrix Calculus, R. M.A. Azzam

Electrical Engineering Faculty Publications

We extend the scope of the Mueller calculus to parallel that established by Jones for his calculus. We find that the Stokes vector S of a light beam that propagates through a linear depolarizing anisotropic medium obeys the first-order linear differential equation dS/dz = mS, where z is the distance traveled along the direction of propagation and m is a 4 × 4 real matrix that summarizes the optical properties of the medium which influence the Stokes vector. We determine the differential matrix m for eight basic types of optical behavior, find its form for the most general anisotropic nondepolarizing …

A Study Of A Wind Tunnel Measurement System For Unsteady Pressures Using Pneumatic Transmission Lines, Mohammed Javed Khan

Theses and Dissertations

The application of pneumatic transmission lines theory to a tube-scanning valve system for unsteady pressure measurements in the AFIT 5-foot wind tunnel is investigated. Transfer gains of various tube-scanning valve configurations were experimentally measured and the validity of a theoretical model verified for a frequency range of 20 Hz to 140 Hz. The selected system having a 0.0625-in. ID flexible tube of 84 in. length connected to a scanning valve was installed in the wind tunnel. Unsteady pressures introduced over an 18 percent airfoil at zero angle of attack were measured with this system. Data were collected for 0, 40, …

Acoustic Emission Monitoring Of Weldments, Theodore Hopwood Ii, James H. Havens

Kentucky Transportation Center Research Report

Weld tests were performed on low-carbon and high-strength, low-alloy steel weldments. The weldments were monitored with an acoustic emission detector during both the 'in-process' and the 'in-cooling' phases of the welding operation. Artificial defects were induced in several of the welds to promote cracking. Some high-strength weldments were designed to produce welds subject to high restraint.

Nondestructive and destructive evaluation of the completed weldments revealed that high acoustic emission activity 'in-cooling' could be correlated with embedded defects and cold-cracking. Copious emission activity was also detected from unflawed weldments. Acoustic emissions were detected in high-strength steel weldments for periods up to …

Deck-Reinforced Slab Systems, Max L. Porter, C. E. Ekberg Jr.

CCFSS Library (1939 - present)

No abstract provided.

Large Cylindrical Bale Transporter, Larry G. Wells

Biosystems and Agricultural Engineering Faculty Patents

The present application is directed to a transporter for transporting large cylindrical bales which includes a mast assembly adapted to be directly attached to a standard three-point hitch of a tractor. The transporter unit includes a two-wheel type trailer and a bale engaging assembly which is rotatably mounted upon the axle of the wheel assembly so that a load positioned on the bale engaging means may be rotated upwardly to support the load directly on the wheels of the transporter. By pivotally attaching the transporter to the mast assembly, the present invention may readily support the entire transporter above the …

Test 1297: Case 2290 Powershift Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …