Engineering Commons^™

The Effect Of Anode Thickness In Sofcs With Anode Supported Ysz Film, Yi-Huang Zhang, Yi Jiang, Zi-Gui Lu, Yong-Lai Dong, Jing-Wang Yan

Journal of Electrochemistry

Solid oxide fuel cells with supported yttria stabilized zirconia electrolyte films on anode substrates of various thickness have been fabricated. The electrochemical performances of the SOFCs have been examined. The results showed that the cell performance was limited by the anodic overpotential, which is caused mainly by a concentration polarization when the anode substrate is thick. The anodic overpotential was reduced obviously as the thickness of anode substrate was decreased. As a result, the performance of the SOFC cell was improved. With a 0.5 mm anode substrate, a SOFC cell produced a power density about 0.19 W/cm² at 800 …

A New Method For The Preparation Of The Electrodes With Very Low Platinum Loading Used In Proton Exchange Membrane Fuel Cell, Zhi-Gang Shao, Bao-Lian Yi, Ming Han, Ya-Guang Qiao, Hao Liu, Jing-Rong Yu

Journal of Electrochemistry

Research and development on low platinum loading electrode is very important in reducing the cost of proton exchange membrane fuel cell(PEMFC) stack. This paper has put forward a new method to prepare the electrode of PEMFC. The pore forming substances were used in this methd. The low platinum loading electrodes (0.02 mg_Pt⋅cm^-2) have already been prepared with the method. Compared with the traditional method, the new method is simple, cheep, and easy to scale up. The superior composition of the electrodes is catalyst: pore forming substance: Nafion= 3:3:1. The performance of a single cell using this …

The Electrochemical Polymerization Of Erythrosin And The Fluorescence Spectra Of Polyerythrosin, Hong-Ping Zhu, Shao-Lin Mu

Journal of Electrochemistry

The solution used for the electrolysis consisted of 0.03 mol·dm^-3 erythrosin, 0.05 mol·dm^-3 sodium tetraborate and 0.5 mol·dm^-3 KCl with pH 8.50. Polyerythrosin film with red color has been electrochemically synthesized using repeated potential cycling between -0.20 and 1.10 V (vs.SCE). The film growth and the electrochemical property of polyerythrosin are affected by electrolytic conditions. Two main absorption peaks of polyerythrosin at 326 nm and 370 nm appear in the UV-visible spectrum, which are different from that of the monomer. Polyerythrosin in dimethyl sulfoxide or dimethylformamide has a strong fluorescence intensity and the fluorescence intensity of polyerythrosin …

Cathodic Indirect Oxidation Of Organic Compounds(Ⅱ)——Cathodic Indirect Epoxidation Of Olefine, Xue-Ying Zhang, Bao-Qiu Cui, Deng-Ping Gu, Wei Li

Journal of Electrochemistry

We described a novel cathodic indirect epoxidation system in which O₂ was first cathodically reduced to H₂O₂. Then VO(acac)₂ was oxidized by H₂O₂ homogeneously to VO(acac)₂OOH which was used to epoxidize some olefine such as maleic, fumaric and crotonic acids. Many affecting factors on the current efficiency were optimized. The research will contribute to the developments of organic electrosynthesis.

The Study On Lithiated Titanium Composite Oxides As Negative Electrode For Lithium-Ion Battery, Xiao-Yan Yang, Shou-Nan Hua, Shu-Yong Zhang

Journal of Electrochemistry

Lithiated titanium composite oxides Li₄Ti₅O₁₂ were prepared from Li₂CO₃ and TiO₂. The XRD results of this composite oxides indicated that the compound had a spinel structure. The electrochemical behavior of lithiated titanium composite oxides was examined. The results showed that this material had an excellent cyclic capability and reversibility for lithium insertion, and had high specific capacity: the initial discharge capacity was 300 mAh·g^-1 , and the reversible capacity was 100 mAh·g^-1 . The discharge plateau (about 1.5 V) and the charge plateau (about 1.6 V) were very …

Studies Of The LialYNi1-YO2 As Cathode Materials For Rechargeable Lithium Ion Batteries, Xiao-Gan Li, Wei-Hua Qiu, Chuan-Gang Lin, Qing-Guo Liu

Journal of Electrochemistry

In this paper, we have synthesized series of single-phase LiAl_yNi_1-yO₂ (differentive in value-y) by solid reaction. Through examining their electrothemical properties, found that, under a proper sintering condition, Li_xAl_0.25Ni_0.75O₂ solution for cathode materials of rechargeable lithium ion batteries showed more pleasing properties in overcharge-resist and cycling life (vs LiNiO₂). When x>1, the capacity can be kept 125mAh/g after 30 cycles under higher charged/discharged voltages ranging from 3.0 V to 4.8 V, whereas that of pure LiNiO₂ has only 61 nAh/g after 25 cycles. The …

Corrosion Behavior Of Reinforcing Steel In Concrete, Rong-Gui Du, Rong-Gang Hu, Zu-De Feng, Jiang-Guang Tan, Chang-Jian Lin

Journal of Electrochemistry

The corrosion behavior of reinforcing steel in concrete in chloride free and chloride contaminated simulated concrete solutions was studied by electrochemical technique. The results showed that the reinforcing steel exhitibted different corrosion characteristics in the different solutons. In general, the steel in concrete was protected in the test solutions with no salt or the lower concentration of NaCl. When the concentration of NaCl is larger than 70%, however, the corrosion behavior of the steel varied considerably, and the corrosion rate increased as pH fell and the concentration of Cl^- increased.

A Study On The Cylindrical Zinc-Air Battery, Sheng-Sian Li, Gui-Mao Zhou, Xin-Ping Ai, Han-Xi Yang

Journal of Electrochemistry

The zinc air battery has advantages of high specific energies and low cost, therefore attracts much interests. However, its application is limited only in prismatic and button type.This paper reported a novel design of cylindrical zinc air batteries and the performances of the batteries tested at various conditions. The results showed that when discharged at the current of 40 mA at 20 °C, the capacity of AA size and AAA size batteries reached 4000mAh and 1400mAh respectively, corresponding to the energy densities 280 Wh/kg and 200 Wh/kg. The effects of the discharge current, temperature and humidity on the performances of …

Synthesis Of Li1+XMn2O4 Cathode Material For Lithium-Ion Batteries With Solution Method, Pei-Song Liu, Sing-Quarn Liu, Qing Li, Zhao-Yong Chen, Bai-Lan Zhang, Zuo-Long Yu

Journal of Electrochemistry

The cathode materials Li_1+xMn₂O₄ were prepared with citric acid complexing and solution impregnating methods. Structure characterization and specific surface area test were performed by means of XRD, BET methods, the influences of calcination temperature, Li/Mn molar ratio and raw materials on the structure and electrochemical capacity of samples have beem examined. The results showed that the Li/Mn molar ratio and calcimation temperature were the key factors affecting the electrochemical capacity of cathode materias. The optimum conditions for synthesis of  Li_1+xMn₂O₄ cathode material were 0≤x≤0.05 and calcined at 750°C. The initial …

High Efficiency Separation Of Microbial Aggregates Using Capillary Electrophoresis, J. M. Schneiderheinze, Daniel W. Armstrong, G. Schulte, David J. Westenberg

Chemistry Faculty Research & Creative Works

Recent advances in the technique of capillary electrophoresis have demonstrated fast, highly efficient separation of mixtures of intact microbes. This paper describes the application of this technique for the separation of microbial aggregates of Micrococcus luteus, Saccharomyces cerevisiae, or Alcaligenes faecalis. The aggregates of these microbes were resolved into several highly efficient peaks with analysis times under 10 min and efficiencies approaching 1 000 000 plates m-1 in some cases. A reproducible relationship was found between the electrophoretic mobility and the aggregation number or size of the cluster under a given set of experimental conditions. Often, cellular aggregation was reversible …

42nd Rocky Mountain Conference On Analytical Chemistry

Rocky Mountain Conference on Magnetic Resonance

Abstracts from the 42nd annual meeting of the Rocky Mountain Conference on Analytical Chemistry, co-sponsored by the Colorado Section of the American Chemical Society and the Rocky Mountain Section of the Society for Applied Spectroscopy. Held in Broomfield, Colorado, July 30 - August 3, 2000.

Santa Clara Magazine, Volume 42 Number 1, Summer 2000, Santa Clara University

Santa Clara Magazine

8 - ATTACK OF THE KILLER TOMATOES? By Miriam Schulman. Beyond the hype of the headlines, there are no simple answers to the ethical questions raised by genetically modified food.

14 - BRAVE NEW WORLD By Tamara Straus. Now the lawyers want inside your head as they struggle to answer, "Who owns an idea?" Just the mere question is changing the face of legal education.

18 - THE GREAT GRADE GIVEAWAY By Jeff Zorn. Today's grades don't mean jack. So says one Santa Clara professor in this memoir and commentary on the evils of modern day grade inflation.

22 - …

Fluid Flow In Micro-Channels: A Stochastic Approach, Hilda Marino Black

Doctoral Dissertations

In this study free molecular flow in a micro-channel was modeled using a stochastic approach, namely the Kolmogorov forward equation in three dimensions. Model equations were discretized using Central Difference and Backward Difference methods and solved using the Jacobi method. Parameters were used that reflect the characteristic geometry of experimental work performed at the Louisiana Tech University Institute for Micromanufacturing.

The solution to the model equations provided the probability density function of the distance traveled by a particle in the micro-channel. From this distribution we obtained the distribution of the residence time of a particle in the micro-channel. Knowledge of …

Routing Optimization Through Computer-Aided Simulation, Madhusudhan Akundi

Electrical & Computer Engineering Theses & Dissertations

Routing has always been a challenging field, and the various techniques of mathematics and operations research have been developed. For commercial organizations, routing has begun to receive extensive attention because of the savings gained in terms of time, money, personnel, and the transportation fleet by developing optimized routing networks. Until recently, it was difficult to develop optimized networks due to the computational difficulties of the problem. However, with the advancement in computer technology and processing speeds, it has become possible to simulate a large number of routing scenarios and determine optimal solutions for a given set of constraints. Not only …

A Flowchart Structure For Modification Of A Modsim Process Model, Murali K. Adatrao

Electrical & Computer Engineering Theses & Dissertations

There are many software processes and software development models that support the development of a software model prior to implementation. However, more often than not, these practices are not followed resulting in a lack of documentation of the intended functionality of the software. As a result, software often becomes a black box for later developers. Even a simple bug fix can turn into an exhaustive task for the developers, as they must attempt to infer the intended system behavior. New designers cannot make any changes to the software or extend the software behavior, as the underlying model within the software …

Advanced Atmospheric Water Vapor Dial Detection System, Tamer Refaat

Electrical & Computer Engineering Theses & Dissertations

Measurement of atmospheric water vapor is very important for understanding the Earth's climate and water cycle. The remote sensing Differential Absorption Lidar (DIAL) technique is a powerful method to perform such measurement from aircraft and space. This thesis describes a new advanced detection system, which incorporates major improvements regarding sensitivity and size. These improvements include a low noise advanced avalanche photodiode detector, a custom analog circuit, a 14-bit digitizer, a microcontroller for on board averaging and finally a fast computer interface.

This thesis describes the design and validation of this new water vapor DIAL detection system which was integrated onto …

Design Of Adaptive Sliding Mode Fuzzy Control For Robot Manipulator Based On Extended Kalman Filter, Abdelrahman Aledhaibi

Mechanical & Aerospace Engineering Theses & Dissertations

In this work, a new adaptive motion control scheme for robust performance control of robot manipulators is presented. The proposed scheme is designed by combining the fuzzy logic control with the sliding mode control based on extended Kalman filter. Fuzzy logic controllers have been used successfully in many applications and were shown to be superior to the classical controllers for some nonlinear systems. Sliding mode control is a powerful approach for controlling nonlinear and uncertain systems. It is a robust control method and can be applied in the presence of model uncertainties and parameter disturbances, provided that the bounds of …

Resolution Of Overlapping Spectra By Wavelength Modulation Spectroscopy, Audra Michiele Bullock

Electrical & Computer Engineering Theses & Dissertations

Wavelength modulation absorption spectroscopy is a highly sensitive, non-intrusive technique for probing gaseous species, which employs the well-known principles of modulation spectroscopy in a novel way. With this technique, parameters such as velocity, density, and temperature can be measured with a high degree of precision. The research presented here shows that wavelength modulation is a convenient means of increasing the sensitivity of an absorption spectroscopy measurement because it allows for harmonic detection. The focus of the dissertation is resolution of overlapping spectra by harmonic detection and the advantages gained by performing detection at the higher harmonics, e.g., sixth and eighth. …

Thermal Lattice Boltzmann Simulation For Multispecies Fluid Equilibration, Linda L. Vahala, Darren Wah, George Vahala, Jonathan Carter, Pavol Pavlo

Electrical & Computer Engineering Faculty Publications

The equilibration rate for multispecies fluids is examined using thermal lattice Boltzmann simulations. Two-dimensional free-decay simulations are performed for effects of velocity shear layer turbulence on sharp temperature profiles. In particular, parameters are so chosen that the lighter species is turbulent while the heavier species is laminar-and so its vorticity layers would simply decay and diffuse in time. With species coupling, however, there is velocity equilibration followed by the final relaxation to one large co- and one large counter-rotating vortex. The temperature equilibration proceeds on a slower time scale and is in good agreement with the theoretical order of magnitude …

Aspects Of Information Flow, Andrew P. Black, Jonathan Walpole

Computer Science Faculty Publications and Presentations

Along with our colleagues at the Oregon Graduate Institute and Georgia Institute of Technology, we have recently been experimenting with real-rate systems, that is, systems that are required to move data from one place to another at defined rates, such as 30 items per second. Audio conferencing or streaming video systems are typical: they are required to deliver video or audio frames from a source (a server or file system) in one place to a sink (a display or a sound generator) in another; the frames must arrive periodically, with constrained latency and jitter. We have successfully built such systems …

Calibration Of Optical Digital Fragmentation Measuring Systems, Norbert H. Maerz, Wei Zhou

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

Optical granulometry systems like WipFrag are required to measure fragments in situ. That is to say, the fragments are in piles where sorting takes place, where fragments are partially overlapped, and where fines may not be seen because they fall in and behind the coarser fragments, or where the fines are simply too small to be seen. As a result, optical systems tend typically to overestimate the size of the distribution, and underestimate the variability of the distribution. The wider the size distribution being measured, the more severe the problem is. This paper presents the results of a study that …

Wright State University College Of Engineering And Computer Science Bits And Pcs Newsletter, Volume 16, Number 6, June 2000, College Of Engineering And Computer Science, Wright State University

BITs and PCs Newsletter

A fourteen page newsletter created by the Wright State University College of Engineering and Computer Science that addresses the current affairs of the college.

Effects Of Ozone/Hydrogen Peroxide Pretreatment On Aerobic Biodegradability Of Nonionic Surfactants And Polypropylene Glycol, Mehmet Kitis, Craig D. Adams, John Kuzhikannil, Glen T. Daigger

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Studies were conducted which used the ozone/hydrogen peroxide (O₃/H₂O₂) advanced oxidation process to pretreat three classes of compounds prior to aerobic biological treatment. The study compounds included ethylene oxide/propylene oxide (EO/PO) block copolymers, polypropylene glycols (PPGs), linear secondary alcoholethoxylates (LSAES), and alkylphenolethoxylates (APEs). After preoxidation with ozone and hydrogen peroxide (added at their stoichiometric ratio), 300 mg/L as COD samples were bioassayed in aerobic batch bioassays with a mixed liquor suspended solids concentration of 1500 mg/L. It was found that unoxidized polypropylated compounds (EO/PO block copolymers and PPGs) and LSAEs tended to be biorecalcitrant, …

Environmental Guidelines For New And Existing Piggeries, A Latto, John Noonan, R. J. Taylor

Bulletins 4000 -

These guidelines apply to the management of Western Australia piggeries in Western Australia, including intensive Growing pigs under intensive conditions where the and extensive operations, straw-based housing and animals spend their entire life cycle indoors, is an combinations of these (otherwise referred to as semi- important part of the Western Australian and intensive housing).

Electrocrystallization Mechanism And Grain Sizes Of Ni-W-B Alloy Eletrodeposits, Fang-Zu Yang, Gang-Min Cao, Xiao Hu, Shu-Kai Xu, Shao-Min Zhou

Journal of Electrochemistry

The electrodeposition characteristics and grain sizes of Ni-W-B alloy have been studied by cyclic voltammetry, potentiostatic step and X-ray diffraction (XRD). The results showed that Ni-W-B alloy electrodeposit obtained from the solution containing ammonium citrate as a complexing agent was presented in the lower electrochemical activity compared with Ni-W alloy. Based upon the i～t curves of potentiostatic step, it was revealed that electrocrystallization of Ni-W-B alloy on glassy carbon followed the mechanism of instantaneous nucleation and three dimensional growth with diffusion controlled. The crystal nucleus number on the surface of electrode was raised by the increase of overpotential. According to …

Study On The Effect Of Sodium Ion On Cycle Performance Of Lithium/Improved Graphite Lithium Ion Cell, Wen-Huang Huang, Yu-Shun Yan, Chun-Rong Wan, Chang-Yin Jiang

Journal of Electrochemistry

The different concentration of Na⁺ was introduced into the non-aqueous eletrolyte system EC/DEC/LiClO 4 with 4A molecular sieve and lithiated 4A molecular sieve, by which the trace amount of water was removed. The concentrations of Na⁺ and Li⁺ were determined by atomic adsorption spectrometry. The cycle performance of lithium/improved graphite cells was then examined by charging and discharging under the constant electric current. The results demonstrated that the cycle performance of the cells was destroyed by the high concentration of Na⁺ under the small electric current. With the increase of electric current the cell became less …

The Studies On Nanosized Materials For Lithium Ion Batteries, Hong Li, Jing-Ze Li, Li-Hong Shi, Guang-Yan Zhu, Qing Chen, Wei Lu, Xue-Jie Huang, Li-Quan Chen

Journal of Electrochemistry

Our recent works about nanosized materials for lithium ion batteries are reported, including the synthesis of nanosized Sb, SnSb, CuSn_x, Si and CuS, their electrochemical performance as anode or cathode active materials, the variation of crystal structure and morphology during discharge and charge cycling. In addition, the self-plasticization of lithium salt with nanosized anion ion in polymer electrolyte, the influence of the electrochemical Li-doping on the Raman spectra and photoluminescence of nano-Si are also introduced. Furthermore, the relationship between intrinsic properties of nanosized materials and their electrochemical behaviors are discussed. The prospect of nanosized materials for lithium ion …

Determination Of Kinetic Parameters Of Enzyme-Immunoelectrode For Sec Assay, Sa-Ying Dong, Xin-Miao Liu, Yuan-Zhi Wang, Guang-Zhang Chen, Ming-Xiang Lv, Bo-Yi Tian

Journal of Electrochemistry

Reaction mechanism of enzyme immunoelectrode is studied by potentiostatic. Rotating disk electrode is used to determine the controlling step of bioelectrode. Under different potentials and different modifying conditions, kinetic parameters of bioelectrodes were measured on the base of electrochemical impendance spectra. At the same time, these parameters are compared and discussed.

The Influence Of Surface Diffusion Of Adsorbed Intermediate On Hydrogen Evolution Reaction At Pt/Nafion Composite Electrodes, Wei-Yi Tu, Lei Su, Wen-Jun Liu, Bing-Liang Wu

Journal of Electrochemistry

The decrease of over-potential of hydrogen evolution reaction at Pt black powder/Nafion microelectrode, comparing that of the Pt microdisk/Nafion electrode, was evident from the polarization curves of the Pt microdisk/Nafion electrode, platinized Pt micrdisk/Nafion electrode and Pt black powder/Nafion microelectrode. It is also evidenced by a plane Pt electrode with an additional free Pt surface. The surface diffusion and the surface recombination reaction of the adsorbed intermediate at the free surface of the Pt particles were supposed. It is an additional reaction path that induced the decrease of the concentration of the adsorbed intermediate. Thereby, the over-potential decreased.

Powder Microelectrode Modified With Nafion-Os(Bpy)3Â 2+ And Pvp Composite And Its Catalysis For No2- Reduction, Pei-Fang Liu, Jia-Wei Yan

Journal of Electrochemistry

The modified powder microelectrode was prepared by etching a Pt (0.1 mm diameter) disk microelectrode and filling in thus formed cavity with Nation-Os(bpy)₃²⁺/PVP composite modified carbon powder. The composite modified powder microelectrode showed cyclic voltammetric behaviors changing with the mole ratio (denoted X) of SO₃^- to Os(bpy)₃²⁺ in Nafion. When X=3, a single pair of current peaks appeared near 0.6V (vs. SCE) due to Os(bpy)₃^2+/3+ redox couple. In contrast, for X=20, a pair of additional current peaks occurred near 0.4V. Both X=3 and X=20 modified powder microelectrodes strongly catalyzed the first …