Engineering Commons^™

Nebraska Summary 545: Massey Ferguson 8450 Diesel Dyna-Step Transmission, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA

The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data.

EXPLANATION OF THE TEST PROCEDURES

Purpose

The purpose of …

Nebraska Summary: S549 Challenger Mt555b, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S530 Case-Ih Jx1090u, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S550 Challenger Mt565b, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S519 Challenger Mt565b, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Pattern Recognition Via Machine Learning With Genetic Decision-Programming, Carl C. Hoff

Browse all Theses and Dissertations

In the intersection of pattern recognition, machine learning, and evolutionary computation is a new search technique by which computers might program themselves. That technique is called genetic decision-programming. A computer can gain the ability to distinguish among the things that it needs to recognize by using genetic decision-programming for pattern discovery and concept learning. Those patterns and concepts can be easily encoded in the spines of a decision program (tree or diagram). A spine consists of two parts: (1) the test-outcome pairs along a path from the program's root to any of its leaves and (2) the conclusion in that …

Investigation Of Ferroelectricity In Newly Synthesized Nitrile Polymer Systems, Matt Poulsen, Stephen Ducharme, Alexander V. Sorokin, Sahadeva Reddy, James M. Takacs, Y. Wen, Jihee Kim, Shireen Adenwalla

Stephen Ducharme Publications

The ferroelectric and piezoelectric properties of newly synthesized polymer systems have been studied. To date PVDF and its copolymers P(VDF-TrFE) have provided the bulk of the knowledge pertaining to ferroelectricity in polymers. Recently, ultrathin ferroelectric films of P(VDF-TrFE) 70:30 have been fabricated using the Langmuir-Blodgett technique [4]. In this study, various new polymers have been synthesized by chemically altering the PVDF structure. This alteration was performed in order to enhance the amphiphilic nature of the polymer and thus improve the LB film quality and control. Various chemical groups have been used to replace the electropositive hydrogen and electronegative fluorine found …

Boron-Rich Semiconducting Boron Carbide Neutron Detector, Andrew D. Harken, Ellen E. Day, Brian W. Robertson, Shireen Adenwalla

Shireen Adenwalla Papers

Data on the neutron detection capabilities of a variety of boron carbide/Si heterojunction diodes is presented. The pulse height spectra are compared with previously measured conversion layer devices and the variations in shape and position of the peaks are discussed.

A Multi-Agent Approach For Solving Optimization Problems Involving Expensive Resources, Hoong Chuin Lau, H. Wang

Research Collection School Of Computing and Information Systems

In this paper, we propose a multi-agent approach for solving a class of optimization problems involving expensive resources, where monolithic local search schemes perform miserably. More specifically, we study the class of bin-packing problems. Under our proposed Fine-Grained Agent System scheme, rational agents work both collaboratively and selfishly based on local search and mimic physics-motivated systems. We apply our approach to a generalization of bin-packing - the Inventory Routing Problem with Time Windows - which is an important logistics problem, and demonstrate the efficiency and effectiveness of our approach.

Robust Temporal Constraint Networks, Hoong Chuin Lau, Thomas Ou, Melvyn Sim

Research Collection School Of Computing and Information Systems

In this paper, we propose the Robust Temporal Constraint Network (RTCN) model for simple temporal constraint networks where activity durations are bounded by random variables. The problem is to determine whether such temporal network can be executed with failure probability less than a given 0 ≤ E ≤ 1 for each possible instantiation of the random variables, and if so. how one might find a feasible schedule with each given instantiation. The advantage of our model is that one can vary the value of ∊ to control the level of conservativeness of the solution. We present a computationally tractable and …

Application Of Meshless Methods For Thermal Analysis, Darrell Pepper, Bozidar Sarler

Mechanical Engineering Faculty Research

Many numerical and analytical schemes exist for solving heat transfer problems. The meshless method is a particularly attractive method that is receiving attention in the engineering and scientific modeling communities. The meshless method is simple, accurate, and requires no polygonalisation. In this study, we focus on the application of meshless methods using radial basis functions (RBFs) — which are simple to implement — for thermal problems. Radial basis functions are the natural generalization of univariate polynomial splines to a multivariate setting that work for arbitrary geometry with high dimensions. RBF functions depend only on the distance from some center point. …

University Of Nevada, Las Vegas Transmutation Research Program: Annual Report Academic Year 2004-2005, Anthony Hechanova, Kathy Lauckner

Transmutation Research Program Reports (TRP)

It is my pleasure to present the UNLV Transmutation Research Program’s fourth annual report that highlights the academic year 2004 – 2005. Supporting this document are the many technical reports and scientific papers that have been generated over the past three years.

In the fourth year of our program, we added 11 new research tasks and saw the conclusion of 8 of the initial 16 independent student research tasks started in 2001 and 2002. In all, the program has sponsored to their conclusion 28 M.S. and 2 Ph.D. degrees. The program supported 58 graduate students and 13 undergraduates in 6 …

Corrosion Of Steel By Lead Bismuth Eutectic, John Farley, Allen L. Johnson, Dale L. Perry

Transmutation Sciences Materials (TRP)

There is an active international interest in lead-bismuth eutectic and similar liquid lead systems because of the relevance to the transmutation of nuclear waste, fast reactors, and spallation neutron sources.

Materials in these systems must be able to tolerate high neutron fluxes, high temperatures, and chemical corrosion. For lead bismuth eutectic (LBE) systems, there is an additional challenge because the corrosive behaviors of materials in LBE are not well understood. Most of the available information on LBE systems has come from the Russians, who have over 80 reactor-years experience with LBE coolant in their Alpha-class submarine reactors. The Russians found …

Environment-Induced Degradation And Crack-Growth Studies Of Candidate Target Materials, Ajit K. Roy

Transmutation Sciences Materials (TRP)

The primary objective of this task was to evaluate the effects of environmental and mechanical parameters on environment induced degradations of candidate target structural materials for applications in spallation-neutron-target systems. The materials selected for evaluation and characterization were martensitic stainless steels including Alloys HT-9, EP-823, and 422.

Accelerator-driven transmutation systems involve bombarding a target material such as molten lead-bismuth-eutectic (LBE) by a proton beam, thereby producing neutrons. The molten LBE target will be contained in a subsystem structural container made of a suitable material such as Alloys HT-9, EP-823, and 422. During the transmutation process, the target structural material may …

Modeling Corrosion In Oxygen Controlled Lbe Systems With Coupling Of Chemical Kinetics And Hydrodynamics, Samir Moujaes, Yitung Chen

Transmutation Sciences Materials (TRP)

The corrosion of structural materials is a major concern for the use of lead-bismuth eutectic (LBE) systems for nuclear applications such as in transmuter targets or fast reactors. Corrosion in liquid metal systems can occur through various processes, including, for example, dissolution, formation of inter-metallic compounds at the interface, and penetration of liquid metal along grain boundaries. Predicting the rate of these processes depends on numerous system operational factors: temperature, system geometry, thermal gradients, solid and liquid compositions, and velocity of the liquid metal, to name a few. Corrosion, along with mechanical and/or hydraulic factors, often contributes to component failure. …

Development Of A Mechanistic Understanding Of High-Temperature Deformation Of Alloy Ep-823, Ajit K. Roy, Brendan O'Toole

Transmutation Sciences Materials (TRP)

During the transmutation process, a significant amount of heat can be generated in a molten lead-bismuth-eutectic (LBE) target, which will be contained in a subsystem structural container made of a suitable martensitic iron-chromium-molbdenum (Fe-Cr-Mo) stainless steel such as Alloys EP-823, HT-9 and 422. These materials will be subjected to high tensile stresses while they are in contact with the molten LBE at temperatures ranging between 400 and 600^oC. Therefore, a research program was conducted to evaluate the deformation characteristics of all three alloys in properly heat-treated conditions at temperatures relevant to the operating conditions.

Developing A Sensing System For The Measurement Of Oxygen Concentration In Liquid Pb-Bi Eutectic, Yingtao Jiang, Bingmei Fu

Transmutation Sciences Materials (TRP)

Although liquid lead-bismuth eutectic (LBE) is a good candidate for the coolant that can be employed in a subcritical transmutation blanket, it is known to be very corrosive to stainless steel, the material used in the containment structure. To mitigate this problem, trace levels of oxygen can be introduced into the system, causing the formation of a protective oxide layer at the interface between the LBE and steel. The proper formation of this oxide layer largely depends on the accurate measurement and subsequent control of the oxygen concentration in liquid LBE.

Yttria Stabilized Zirconia (YSZ) oxygen sensors, using molten bismuth …

Use Of Positron Annihilation Spectroscopy For Stress-Strain Measurements, Ajit K. Roy

Transmutation Sciences Materials (TRP)

Engineering metals and alloys, when subjected to tensile loading beyond a limiting value, undergo plastic deformation resulting in lattice defects such as voids and dislocations. These imperfections interact with the crystal lattice, producing a higher state of internal stress, also known as residual stress, which can be associated with reduced ductility. Residual stresses are also generated in welded structures due to rapid solidification and resultant dissimilar metallurgical microstructures between the weld and the base metals. Development of these internal stresses is often influenced by incompatible permanent strain resulting from thermal and mechanical operations associated with welding and plastic deformation. These …

Fundamental And Applied Experimental Investigations Of Corrosion Of Steel By Lbe Under Controlled Conditions: Kinetics, Chemistry Morphology, And Surface Preparation, John Farley, Allen L. Johnson, Dale L. Perry

Transmutation Sciences Materials (TRP)

Advanced nuclear processes such the transmutation of nuclear waste, fast reactors, and spallation neutron sources require advanced materials systems to contain them. In particular, a successful program in nuclear waste processing that includes transmutation in accelerator-driven systems and fast reactors requires structural materials that are stable in the presence of non-moderating coolants. A prime candidate for such a coolant is Lead Bismuth Eutectic (LBE).

Materials in these systems must be able to tolerate high neutron fluxes, high temperatures, and chemical corrosion. For LBE systems, there is an additional challenge because the corrosive behaviors of materials in lead bismuth are not …

Effect Of Silicon Content On The Corrosion Resistance And Radiation- Induced Embrittlement Of Materials For Advanced Heavy Liquid Metal Nuclear Systems, Ajit K. Roy

Transmutation Sciences Materials (TRP)

This task is focused on the evaluation of the effect of Si content on the corrosion behavior and radiation-induced embrittlement of martensitic steels having chemical compositions similar to that of modified 9Cr-1Mo steel. Numerous state-of-the-art experimental techniques are currently being planned to be employed to achieve the desired research goal.

Theoretical Modeling Of Protective Oxide Layer Growth In Non-Isothermal Lead Alloy Coolant Systems, Yitung Chen, Jinsuo Zhang, Huajun Chen, Jichun Li

Transmutation Sciences Materials (TRP)

In advanced nuclear energy systems, lead-alloys (e.g., lead, lead bismuth eutectic) emerge as strong candidates for transmutation and advanced reactor systems as nuclear coolants and high-power spallation neutron targets. However, it is widely recognized that corrosion of materials caused by lead-alloys presents a critical barrier to their industrial use. A few experimental research and development projects have been set up by different groups such as LANL to study the corrosion phenomena in their test facilities and to develop mitigation techniques and materials.

The goal of the proposed research project is to provide basic understanding of the protective oxide layer behaviors …

Corrosion Barrier Development For Lbe Corrosion Resistance, Biswajit Das

Transmutation Sciences Materials (TRP)

In the last quarter, a specialized sample holder was developed for the anodization of alumina on steel. In addition, it was determined that oxalic acid was the most appropriate acid for the anodization of these structures. The steel samples obtained from LANL were first cut into a number of pieces, each measuring 11mm x 8mm x 1.6mm, to allow multiple experiments. Special care was taken to ensure that the cutting process did not damage the samples. After investigation of several techniques, including laser cutting, the samples were cut using EDM wires. The cut steel pieces did not show any damage …

Corrosion Barrier Development For Lbe Corrosion Resistance: Quaterly Report, Biswajit Das

Transmutation Sciences Materials (TRP)

With the demonstration of formation of nanoporous alumina on steel and its good adhesion to substrate under thermal cycling, the next project task was to synthesize Chromium nanowires inside the alumina pores. During the previous quarter, a specialized sample holder was developed towards this goal. Various techniques for the deposition of Chromium were investigated and electro-deposition was determined to be the most suitable approach due to the large aspect ratio of the pores. A challenge in using electro-deposition for porous alumina is the potential sealing of the pores in aqueous solutions at higher temperatures. To avoid this problem, a search …

Development Of Nanostructure Based Corrosion-Barrier Coatings On Steel For Transmutation Applications, Biswajit Das

Transmutation Sciences Materials (TRP)

Advanced transmutation systems require structural materials that are able to withstand high neutron fluxes, high thermal cycling, and high resistance to chemical corrosion. The current candidate materials for such structures are ferritic and ferritic-martensitic steels due to their strong resistance to swelling, good microstructural stability under irradiation, and the retention of adequate ductility at typical reactor operating temperatures.

In parallel, lead bismuth eutectic (LBE) has emerged as a potential spallation target material for efficient production of neutrons, as well as a coolant in the accelerator system. While LBE has excellent properties as a nuclear coolant, it is also highly corrosive …

Neutron Multiplicity Measurements Of Target/Blanket Materials, Denis Beller

Transmutation Sciences Physics (TRP)

To optimize the performance of accelerator-driven sub-critical (ADS) transmutation systems, engineers will need to design the system to operate with a neutron multiplication factor just less than that of a critical, or self-sustaining, system. This design criterion requires particle transport codes that instill the highest level of confidence with minimal uncertainty, because larger uncertainties in the codes require larger safety margins in the design and result in a lower efficiency of the ADS transmuter. For current design efforts in the U.S., a Monte Carlo particle transport code MCNPX is used to model neutron production and transport for spallation neutron systems. …

Reactor Physics Studies For The Afci Reactor-Accelerator Coupling Experiments (Race) Project, Denis Beller

Transmutation Sciences Physics (TRP)

The specific research objective of this three-year project is to design and conduct an accelerator driven experiment at one of the Texas universities. This experiment will help demonstrate in the U.S. the ability to design, compute, and conduct ADSS experiments; and to predict and measure source importance, coupling efficiency, sub-critical reactor kinetics and source-driven transients. In addition, both steady state and transient ADSS benchmarks will be created for the nuclear community to develop and test new computational codes and methods, and the importance of a driving neutron source in various regions of different subcritical assemblies will be mapped. Experiments will …

Development Of A Systems Engineering Model Of The Chemical Separations Process, Yitung Chen, Darrell Pepper, Sean Hsieh

Separations Campaign (TRP)

The chemical processing of used nuclear fuel is an integral component of any strategy for the transmutation of nuclear waste. Due to the large volume of material that must be handled in this first step of the transmutation process, the efficiency of the separations process is a key factor in the potential economic viability of transmutation strategies. The ability to optimize the chemical separation systems is vital to ensure the feasibility of the transmutation program.

Systems analysis, or total systems modeling, is one of the strongest tools available to researchers for understanding and optimizing complex systems such as chemical separations …

Nuclear Criticality, Shielding, And Thermal Analyses Of Separations Processes For The Transmutation Fuel Cycle, William Culbreth, Denis Beller

Separations Campaign (TRP)

The first step in any transmutation strategy is the separation of radionuclides in used nuclear fuel. The current separation strategy supporting the Advanced Fuel Cycle Initiative (AFCI) program is based on the use of a solvent extraction separation process to separate the actinides, fission products, and uranium from used commercial nuclear fuel, and on the use of pyrochemical separation technologies to process used transmuter fuels. To separate the fission products and transuranic elements from the uranium in used fuel, the national program is developing a new solvent extraction process, the Uranium Extraction Plus, or UREX+, process based on the traditional …

Development, Fabrication And Study Of Fullerene-Containing Carbon Material (Fcc) For Immobilization Of Iodine: Progress Report #1-4, Michael Savopulo, Boris E. Burakov

Separations Campaign (TRP)

During current reporting period the experiments on synthesis of ceramic-like material by conversion of iodine-doped FCC and activated carbon to Si_xC_y have been completed. Cold pressed granules of FCC and activated carbon were rinsed in water-ethanol solution of tetraethoxysilane (TEOS), Si(OC₂H₅)₄, and then used for further synthesis. All new samples obtained have been studied using precise powder XRD analysis.

Development Of Integrated Process Simulation System Model For Spent Fuel Treatment Facility (Sftf) Design, Yitung Chen, Sean Hsieh

Separations Campaign (TRP)

The major objective is to create a framework that combines all the strengths of AMUSE’s complicated calculations, well established commercial system process package such as ASPENPLUS, HYSYS and PRO/II and TRPSEMPro’s flexible parameter optimization modules. Development of the process simulation code can be done using the solvent extraction process experience at Argonne National Laboratory and in collaboration with the NCACM.

The major activities of the task are the following:

• Develop a framework for simulating the SFTF process using AMUSE code, commercial process package, such as ASPEN- PLUS, and system engineering model.
• Develop a middleware package that can communicate between the …