Engineering Commons^™

Interaction Between Metal Fission Products And Triso Coating Materials, Clemens Heske

Fuels Campaign (TRP)

This project focuses on the chemical bonding and interface formation of metal fission products with the coating materials used in tri-isotropic (TRISO) fuel particles for gas-cooled reactors. By combining surface- and bulk-sensitive spectroscopic and microscopic methods, intermediate chemical phases at the interface, intermixing/diffusion behavior, and the electronic interface structure for different coating materials and metals are examined.

In detail, the project studies the interface formation of Pd, Cs, and Ag with SiC and pyrolytic carbon. Using SiC single crystals and highly-ordered pyrolytic carbon (HOPG) as substrates, interfaces are prepared under controlled conditions in an ultra-high vacuum environment and are studied …

Design Concepts And Process Analysis For Transmuter Fuel Manufacturing, Georg F. Mauer

Fuels Campaign (TRP)

The safe and effective manufacturing of actinide-bearing fuels for any transmutation strategy requires that the entire manufacturing process be contained within a shielded hot cell environment. To ensure that the fabrication process is feasible, the entire process must be designed for remote operation. The equipment must be reliable enough to perform over several decades, and also easy to maintain or repair remotely. The facility must also be designed to facilitate its own decontamination and decommissioning. In addition to these design factors, the potential viability of any fuel fabrication process will also be impacted by a number of variables, such as …

Dissolution, Reactor, And Environmental Behavior Of Zro2-Mgo Inert Fuel Matrix, Kenneth Czerwinski

Fuels Campaign (TRP)

This project will examine inert fuels containing ZrO₂ and MgO as the inert matrix. Ceramics with this inert matrix, Ce, U and eventually Pu will be synthesized and examined. While the Advanced Fuel Cycle Initiative focus is on inert fuels with Pu as the fissile component, this task will perform initial laboratory experiments with Ce and U. The initial work with Ce will be performed early in the project with results used as a basis for U studies. Reactor physics calculations will be used to examine suitable quantities of burnable poisons from the candidate elements Gd, Er, or Hf. …

Impact Of The Synthesis Process On Structure Properties For Afci Fuel Candidates, Kenneth Czerwinski

Fuels Campaign (TRP)

The research objectives are:

• To explore a low-temperature fluoride route to synthesize actinide nitrides. • To characterize actinide nitrides structurally and thermally.

• To use high resolution TEM techniques to explore the microstructure of the radioactive samples.

Solution-Based Synthesis Of Nitride Fuels, Kenneth Czerwinski, Tyler A. Sullens

Fuels Campaign (TRP)

One of the original synthetic routes devised for the synthesis of U (III)N involved the entire reaction taking place in liquid ammonia. Several experimental reactions were conducted in an attempt to synthesize the UI₃(NH₃)_x and U(NH₂)₃(NH₃)_x precursors of U(III) N. Each attempt involved cleaning of the uranium metal to remove the oxide coating of the metal reagent with 3 washes of concentrated nitric acid, each followed by a rinse with liquid ammonia. Success of this cleaning procedure was varied, with a majority of cleaned metal oxidizing rapidly once …

Improved High-Temperature Stability And Sun-Light-Driven Photocatalytic Activity Of Sulfur-Doped Anatase Tio2, Suresh Pillai, Declan Mccormack, Pradeepan Periyat, John Colreavy, Steve Hinder

Articles

No abstract provided.

Functorial Coalgebraic Logic: The Case Of Many-Sorted Varieties, Alexander Kurz, Daniela Petrişan

Engineering Faculty Articles and Research

Following earlier work, a modal logic for T-coalgebras is a functor L on a suitable variety. Syntax and proof system of the logic are given by presentations of the functor. This paper makes two contributions. First, a previous result characterizing those functors that have presentations is generalized from endofunctors on one-sorted varieties to functors between many-sorted varieties. This yields an equational logic for the presheaf semantics of higher-order abstract syntax. As another application, we show how the move to functors between many-sorted varieties allows to modularly combine syntax and proof systems of different logics. Second, we show how to associate …

Carbon Permits, Jun-Ki Choi, Bhavik R. Bakshi

Mechanical and Aerospace Engineering Faculty Publications

The Encyclopedia of Global Warming and Climate Change helps readers learn about the astonishingly intricate processes that make ours the only planet known to be habitable. These three volumes include more than 750 articles that explore major topics related to global warming and climate change—ranging geographically from the North Pole to the South Pole, and thematically from social effects to scientific causes.

Volcanic Activity: Processing Of Observation And Remote Sensing Data (Vapor), Mark Wylie

Reports

The World Bank makes a very clear distinction between disasters and natural phenomena. Natural phenomena are events like volcanic eruptions. A disaster only occurs when the ability of the community to cope with natural phenomenon has been surpassed, causing widespread human, material, economic or environmental losses. By these definitions, volcanic eruptions do not have to lead to disasters. On November 13, 1985, the second most deadly eruption of the twentieth century occurred in Colombia. Within a few hours of the eruption of the Nevado del Ruiz volcano, 23,000 people were dead because no infrastructure existed to respond to such an …

Generation Of High-Repetition-Rate Pulses Utilizing Cascaded Single Mode Fiber And Semiconductor Optical Amplifier, Jianwei Wu, Hai-Bo Bao

Turkish Journal of Electrical Engineering and Computer Sciences

To generate high-repetition-rate optical pulses, a novel and simple device is demonstrated, in which the cascaded single mode fiber (SMF) with negative third order dispersion and semiconductor optical amplifier (SOA) are adopted. Numerical research results show that let an optical pulse with center wavelength in zero dispersion wavelength of optical fiber transit in SMF for generating an oscillation pulse. Subsequently, the followed SOA is provided for amplification. As a consequence, the high-repetition-rate optical pulses can be obtained.

A Study On The Reliability Of Polyester Insulators Blended With Borax, Aysel Ersoy, Yasi̇n Özcelep, Ayten Kuntman

Turkish Journal of Electrical Engineering and Computer Sciences

Tracking is the main factor which limits the safe working electric stress of insulation in power system applications. Polymer samples have been tested in laboratory conditions according to ASTM D2303 on accelerated inclined plane tracking test. In this paper, a model based on improved Weibull statistics is proposed for estimating the breakdown time of polymeric insulating materials with borax. The confidence intervals of the Weibull shape parameter and the Weibull scale parameter are determined for the borax concentration values using the Weibull 7++ program.

Tractor Test 1918: New Holland Tt 50a, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 1938: New Holland T2330, New Holland Tc50, New Holland Boomer 3050, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 1928: Challenger Mt945b Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S645 Challenger Mt535b, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S621a Case-Ih Magnum 180, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S671 Case-Ih Puma 140, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S656 Challenger Mt645c Scr, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S726 New Holland T4050, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S723 New Holland T4040, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S719 New Holland T4020, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Recent Advances In Perfectly Matched Layers In Finite Element Applications, Özlem Özgün, Mustafa Kuzuoğlu

Turkish Journal of Electrical Engineering and Computer Sciences

We present a comparative evaluation of two novel and practical perfectly matched layer (PML) implementations to the problem of mesh truncation in the finite element method (FEM): locally-conformal PML, and multi-center PML techniques. The most distinguished feature of these methods is the simplicity and flexibility to design conformal PMLs over challenging geometries, especially those with curvature discontinuities, in a straightforward way without using artificial absorbers. These methods are based on specially- and locally-defined complex coordinate transformations inside the PML region. They can easily be implemented in a conventional FEM by just replacing the nodal coordinates inside the PML region by …

Nebraska Tractor Test 1932: Agco Lt95a, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

New Method For Approximating Vague Sets To Fuzzy Sets Based On Voting Model, Jian Liu, Zhizhan Liu, Shunxiang Wu, Yongjian Zhang

Electrical and Computer Engineering Faculty Research & Creative Works

By analyzing Vague Sets voting model, we bring forth a new method for approximating Vague Sets to Fuzzy Sets, and its general process is presented in the article. In a voting model, firstly, we suppose that the abstainers must vote for once more, and the results are close studied. Then the randomicity, uncertainty, and conformity of voting are found. As we know, an abstainer may favor somebody, oppose somebody, or just abstain. In this article, we suppose the distribution of results is consistent with a normal distribution. So, we advance the new approximation method based on Gauss Distribution. © 2008 …

My Collaboration With Raj Mittra: Contributions To The Theory Of Perfectly Matched Layers, Mustafa Kuzuoğlu

Turkish Journal of Electrical Engineering and Computer Sciences

No abstract provided.

Use Of Characteristic Basis Function Method For Scattering From Terrain Profiles, Atacan Yağbasan, Celal Alp Tunç, Vakur B. Ertürk, Ayhan Altintas, Raj Mittra

Turkish Journal of Electrical Engineering and Computer Sciences

An integral equation (IE) based solution procedure is presented for the rigorous analysis of scattering from terrain profiles. The procedure uses characteristic basis function method (CBFM), which is hybridized with the forward-backward method (FBM), to reduce the storage requirements of the resultant Method of Moments (MoM) impedance matrix, as well as to accelerate the solution procedure. Numerical results in the form of induced current and scattered field are presented to assess the accuracy and efficiency of the solution procedure.

The Characteristic Basis Function Method (Cbfm): A Numerically Efficient Strategy For Solving Large Electromagnetic Scattering Problems, Eugenio Lucente, Gianluigi Tiberi, Agostino Monorchio, Giuliano Manara, Raj Mittra

Turkish Journal of Electrical Engineering and Computer Sciences

The objective of this paper is to describe a numerically efficient strategy for solving large electromagnetic scattering problems. This novel approach, termed as the Characteristic Basis Function Method (CBFM), is based on utilizing Characteristic Basic Functions (CBFs)-special functions defined on macro domains (blocks)-that include a relatively large number of conventional sub-domains discretized by using triangular or rectangular patches. The CBFs can be derived either analytically (from PO solutions), or by applying the conventional MoM. Use of these basis functions leads to a significant reduction in the number of unknowns, and results in a substantial size reduction of the MoM matrix. …

Analysis And Optimization Of Mobile Phone Antenna Radiation Performance In The Presence Of Head And Hand Phantoms, Erdem Ofli, Chung-Huan Li, Nicolas Chavannes, Niels Kuster

Turkish Journal of Electrical Engineering and Computer Sciences

A commercial clam shell phone CAD model is used to numerically investigate the effect of a hand phantom on mobile phone antenna radiation performance. The simulation results show that the grip of the hand phantom is the most important parameter to antenna performance. The antenna is converted into a parameterized form, then optimized to achieve the targeted multi-band performance in real-usage conditions.

Dual-Band Split-Ring Antenna Design For Wlan Applications, S. Cumhur Başaran, Yunus E. Erdemli̇

Turkish Journal of Electrical Engineering and Computer Sciences

A dual-band microstrip antenna based on split-ring elements is introduced for WLAN (2.4/5.2 GHz) applications. The proposed split-ring antenna (SRA) has a compact novel design which provides about 2% impedance-bandwidth without a need for additional matching network. Analysis and design of the proposed microstrip antenna is carried out by means of full-wave simulators based on the finite-element method.

Comparison Of Rectangular And Cylindrical Fdtd Representations On A Ring Resonator Problem, Funda Akleman, Levent Sevgi̇

Turkish Journal of Electrical Engineering and Computer Sciences

The aim of this paper is to discuss rectangular and cylindrical representations of finite-difference time-domain (FDTD) method over characteristic tests and comparisons. A ring resonator is chosen as a canonical structure and modeled with both rectangular- and cylindrical-FDTD packages. Calibration against analytical exact solution derived in terms of cylindrical Bessel functions is also performed. It is shown that rectangular-FDTD with periodic boundary condition, where the computation domain is reduced, can also be applied in modeling circular structures.