Engineering Commons^™

Characterizing Indoor Surface Voc Contamination After The 2025 Los Angeles Fires, Brett W. Stinson, Emily Lei, Elliott T. Gall

Mechanical and Materials Engineering Faculty Publications and Presentations

We quantify volatile organic compound (VOC) emissions from indoor surface swabs and portable air cleaner (PAC) filters collected in a home 30 days after the 2025 Los Angeles wildland-urban interface (WUI) fires. We calculate emissions for 17 fire-relevant compounds. Surface emissions exceeded those of clean controls, and emissions from a windowsill in a room without a PAC were ∼15× and ∼2× higher for benzene and toluene, respectively, than rates reported in the literature for comparable materials unaffected by smoke/soot. Particle filters installed in PACs at the start of the fire emitted aromatics at rates comparable to those reported in a …

Contrasting Coastal Dune Environments In Chile, Aurora Christianson

Student Research Symposium (SRS)

Emerging coastalization and urbanization threats to the prehistoric Concón Dunes and Humedal de Mantagua coastal area of Chile is being investigated by researchers via uncrewed aircraft systems (UAS). Four UAS were utilized: Anzu Raptor T, DJI Mavic 3E, DJI Mavic 3M, and DJI Air 3 to collect various images of the coastal dunes. Multispectral and RGB cameras gather images by photogrammetry to create orthomosaics and monitor vegetation indexes in Pix4Dmapper. Thermal cameras provided images in rainbow, white hot infrared, and black hot infrared schemes to monitor wildlife and vegetation. The normalized difference vegetation index (NDVI) was calculated to visualize overall …

Uav-Deployable Open-Source Sensor Nodes For Spatial And Temporal In Situ Water Quality Monitoring And Mapping, Matthew Burnett, Mohamed Abdelwahab, Joud N. Satme, Austin Downey, Gabriel Barahona Smith, Antonio Fonce, Jasim Imran

Faculty Publications

Cost efficient, spatially resolved water quality monitoring is essential for managing pollution and protecting aquatic ecosystems. This study presents a low-cost (approximately USD 200), open-source, unmanned aerial vehicle (UAV)-deployable in situ sensor node for real-time assessment of surface-water conditions. The system integrates sensors for pH, turbidity, temperature, and total dissolved solids (TDSs), with onboard data logging and real-time clock (RTC) synchronization. Bench validation of the sensor package yielded mean absolute percentage errors of 1.34% for pH, 5.23% for TDS, and 0.81% for temperature, and the device operated continuously for 42 h. Field deployment demonstrated its ability to resolve spatial gradients, …

An Autonomous Robotic System For Object Retrieval And Delivery: Enhancing Independence For Users Living With Disability And Older Adults, Jincheng Li, Chenghao Lin, Amna Mazen, Youssef A. Bazzi

Michigan Tech Publications

As the global population ages, there is a growing need for assistive technologies to help older adults maintain their independence. This work presents a cost-effective autonomous socially assistive robot designed for object retrieval and delivery, enhancing accessibility in home environments. The system is built on the Robot Operating System (ROS) framework and integrates three key components: the Pioneer P3-DX mobile robot for autonomous navigation, the ReactorX-200 robotic arm for pick-and-place operations, and the Kinect v2 RGB-D camera for object detection and localization. Users interact with the robot through natural language processing by issuing voice commands to retrieve various objects. Microsoft …

Developments Of New Metal-Free Batteries And Self-Charging Batteries For Sustainability, Abhishek Paudel

LSU Doctoral Dissertations

The growing concerns over the limitations and environmental impact of conventional lithium-ion batteries (LIBs) have driven the search for more sustainable energy storage solutions. Metal-free batteries, such as those utilizing ammonium ions (NH₄⁺), offer a compelling alternative due to their non-toxic nature, abundant availability, and unique electrochemical properties. The NH₄⁺ ion's lower molar mass and distinct tetrahedral structure enable efficient charge transfer and intercalation, distinguishing it from traditional metal ions and potentially improving battery performance. Self-charging batteries, which integrate piezoelectric materials to harvest ambient mechanical energy, present a significant advancement in energy storage technology. By capturing and converting mechanical energy …

Striation Characteristics In Atmospheric Pressure Ac-Driven Glow Discharge Operating In Monoatomic Gas, Ayuob K. Alwahaibi, Sang Hee Won, Tanvir Farouk

Faculty Publications

Striation in an atmospheric pressure AC-driven helium glow discharge operating at 25 kHz is experimentally characterized. Striation behavior is characterized by the visualization of discharges and voltage–current measurements over a range of plasma power. Voltage–current characteris tics reveal that striations form in the “normal” glow regime of operation, with a higher number of strata at low current, diminishing as dis charge current increases. The relative differences and similarities in the striation patterns during the positive and negative cycles are identified. High-speed imaging shows the striations to be traveling in time—“moving striations.” The spatial luminosity of the striations is tracked over …

Artificial Intelligence And Additive Manufacturing As A Coupled Design System: Rethinking Inference, Manufacturability, And Design Education, Charul Chadha, Garth Crosby, Sabit Ekin, Mohamed Gharib, Eman Hammad, Congrui Jin, Ali Ahmad Malik, Noemi Mendoza Diaz, Calahan Mollan, Monsuru Ramoni

Manufacturing & Industrial Engineering Faculty Publications

Artificial intelligence (AI) is becoming deeply integrated into additive manufacturing (AM) workflows, reshaping how designers approach geometry, materials, and process constraints. AI holds significant potential by accelerating design exploration, revealing complex patterns in AM behavior, and supporting earlier assessment of manufacturability. At the same time, it introduces new risks related to model transparency, data quality, physical validity, and the potential for overreliance by students and practitioners. This perspective examines these issues through four guiding questions that address the role of AI in AM-enabled design, the gaps that limit or enable AI contribution, the implications for engineering education, and the responsibilities …

Bulk Absorber Acoustic Characterization Via The Two-Cavity Impedance Tube Methoda), Anthony Ciletti, Janith Godakawela, Martha Brown, Bhisham Sharma

Michigan Tech Publications

The primary goal of this study is to investigate and refine the two-cavity impedance tube method for acoustic characterization of bulk porous materials, specifically addressing previously unexplained inaccuracies in the prediction of surface impedance and absorption coefficients. Unlike the conventional two-thickness approach, the two-cavity method requires only one sample thickness and involves conducting measurements at various air cavity depths behind the sample. The initial analyses revealed previously unidentified numerical instabilities, resulting in anomalous predictions of sound absorption at specific frequencies. Through systematic investigation and use of calculated data, the numerical origins of these anomalies are uncovered and a practical solution, …

Patient‐Specific Computational Flow Simulation Reveals Adverse Hemodynamic Factors Associated With Occlusion Of Directional Branches After Fenestrated‐Branched Endovascular Aneurysm Repair, Kenneth Tran, Jesse Chait, Emmanuel Tenorio, Weiguang Yang, Alison Marsden, Bernardo Mendes, Jason T. Lee, Gustavo S. Oderich

Mechanical Engineering Faculty Publications

Background: Fenestrated and branched endovascular aneurysm repair can be complicated by branch vessel occlusion in the absence of structural stenosis. We hypothesized that computational flow simulation could identify adverse hemodynamic features associated with postfenestrated and branched endovascular aneurysm repair branch occlusion.

Methods: Patients undergoing 4-vessel fenestrated and branched endovascular aneurysm repair for Extent II to IV thoracoabdominal aortic aneurysms were retrospectively reviewed. Branches that occluded without identifiable kinking or stenosis on computed tomography were included, along with an equal cohort of anatomy-matched patent controls. Patient-specific pulsatile rigid-wall simulations were performed using SimVascular with individualized geometries and boundary conditions. Abnormal time-averaged …

High-Throughput Computational Framework For High-Order Anharmonic Thermal Transport In Cubic And Tetragonal Crystals, Zhi Li, Huiju Lee, Chris Wolverton, Yi Xia

Mechanical and Materials Engineering Faculty Publications and Presentations

Accurate first-principles prediction of lattice thermal conductivity (κ L) remains challenging in identifying materials with extreme thermal behavior. While the harmonic approximation with three-phonon scattering (HA + 3ph) is now routine, reliable κ L prediction often requires higher-order anharmonic effects, including self-consistent phonon renormalization, three- and four-phonon scattering, and off-diagonal heat flux (SCPH + 3, 4ph + OD). We present a state-of-the-art high-throughput workflow that unifies these effects and apply it to 773 cubic and tetragonal crystals spanning diverse chemistries and structures. From 562 dynamically stable compounds, we assess the hierarchical impacts of higher-order anharmonicity. For around 60% of materials, …

Generative Artificial Intelligence In Aircraft Design Optimization, Xiaosong Du

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Aircraft design optimization is essential for improving aircraft performance (such as reduced fuel consumption and lowered noise), which leads to more efficient, sustainable, and affordable aircraft. Conventional aircraft design adopts physics-based simulation models, but iteratively evaluating simulation models is computationally intensive, or even practically impossible. Meanwhile, artificial intelligence (AI) emerges as a revolutionary game changer in the modern engineering industry, including aircraft design optimization. Generative AI (genAI), one of the groundbreaking AI methods, has been advancing aircraft design optimization from various aspects, including intelligent parameterization, predictive modeling, training facilitation, and constraints handling. However, there is a lack of a review …

Manufacturing And Material Property Verification Of Short Fiber Particle Reinforced Composites, Megan Elise Howell

Graduate Theses - Mechanical Engineering

This thesis investigates the manufacturing, testing, and material property verification of short fiber and particle reinforced polymer composites intended for use in flywheel energy storage systems. Composite tensile specimens were fabricated using controlled mold geometries and autoclave-assisted curing to improve consolidation quality and reduce void content. Short carbon fibers and particulate reinforcements were selected to balance mechanical performance, manufacturability, and isotropy for high-speed rotor applications. Tensile testing was performed using a tensile testing machine, and machine compliance effects were quantified and removed to obtain accurate elastic moduli. Experimental results were compared against analytical micromechanics predictions to evaluate stiffness trends and …

Coe Annual Technical Review 2025, Jianshun Zhang, Bing Dong

SyracuseCoE

No abstract provided.

Hybrid Sensing For Near-Earth Space Domain Awareness: Leveraging Space-Based Assets For Augmenting Optical Ground Observations, Smriti Nandan Paul, Hang Woon Lee

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Because of recent advancements in space technologies, easier and more economical access to space, and an increase in commercial interests, the near-Earth space environment has witnessed an exploding number of objects being put into orbit. In particular, the low Earth orbit (LEO) region is at an increased risk of orbital collisions from large satellite constellation projects. Thus, monitoring LEO objects for space domain awareness and space traffic management has become increasingly imperative. In this paper, we use the concept of limited-CDF (cumulative distribution function) surface and mutual information for designing sensor tasking algorithms focusing on regular observation of known catalog …

Three-Dimensional Topographical Effects On The Generation Of Internal Lee Waves, Haosen H.A. Xu, Xiaowei Zhu, Kaiwen Zheng

Mechanical and Materials Engineering Faculty Publications and Presentations

Internal lee waves generated by the interaction between geostrophic flows and ocean-floor topography are recognized as an important pathway for transferring energy from large-scale circulation to small-scale mixing in the deep ocean; however, energy fluxes inferred from field observations often fall well below estimates based on classical linear theory. Here, we use direct numerical simulations to examine how three-dimensional (3D) topographic structure alters the generation and energy pathways of internal lee waves. We simulated idealized stratified flows impinging on twodimensional (2D) and 3D sinusoidal topography in a radiating regime. We used Reynolds decomposition based on spatial averaging to isolate wave-induced …

Influence Of Superhydrophobic Surface Microstructure On Transient Jet Impingement Cooling, D. Jacob Butterfield, Brian D. Iverson, Daniel Maynes, Julie Crockett

Faculty Publications

Water jet impingement is an effective method of rapidly cooling a surface, but heat transfer from the surface is highly dependent on the surface condition and properties. Here, the impact of a superhydrophobic (SH) surface on heat transfer to an impinging, axisymmetric, room-temperature water jet with Re=6 x 10³to 18 x 103 is explored. SH surfaces are created by etching thin silicon wafers to form different micropatterns (posts or holes). Surfaces are heated to between 200 and 320°C, and the local surface temperature is measured with a thermal camera. The time resolved heat transfer from the surface and …

A Virtual-Reality-Based Dental Simulator For Endodontics With Automated Formative Feedback, Yousef Salah Abo El Ela

Theses and Dissertations

Advancements in virtual reality (VR) and haptic technology are transforming the landscape of medical and dental education, offering new avenues for safe, immersive, and repeatable training experiences. Within dentistry, endodontics presents unique challenges for preclinical education due to anatomical complexity, limited access to extracted teeth, ethical concerns, and the shortcomings of conventional plastic models. Despite endodontics specific plastic teeth being available, they fall short of replicating the hardness of real extracted teeth, are relatively costly compared to generic plastic teeth, and are ultimately a disposable item which makes them inadequate as a sustainable long-term solution. Extracted teeth do a much …

Mechanical Characterization And Modeling Of Rat Myocardia Under The Influence Of Epirubicin, Abdallah Mahmoud Alkhaiyat

Theses and Dissertations

Cancer remains a predominant health challenge that is responsible for a significant portion of global morbidity and mortality. Epirubicin (EPI), a chemotherapeutic anti-cancer drug, has shown remarkable efficacy in combating various malignancies. However, it is known to have undesirable side effects on the heart, collectively referred to as cardiotoxicity. This research investigates the adverse effects of chemotherapy on cardiac contractility through an in vitro examination of the mechanics of healthy and infarcted animal heart tissues. Electrically stimulated slices of rat ventricular tissue were tested using an isometric force measurement tissue bath. The tissue slices were subjected to uniaxial stretching, allowing …

Harnessing Ml And Iiot For Traceability In Continuous Production Systems: A Conceptual Framework, Kholoud M. Abdelaal

Theses and Dissertations

In the era of rapid technological advancement, the manufacturing sector faces increasing pressure to leverage emerging technologies to enhance operational efficiency and minimize waste. In this context, traceability plays a pivotal role, as it provides complete visibility of processes and products throughout manufacturing systems, enabling them to identify areas for improvement and take corrective actions accordingly. Additionally, traceability ensures compliance, supports product recalls, provides a clear understanding of the system’s performance, and enables fact-driven decision-making in multiple aspects of the manufacturing system. Although the broad spectrum of traceability applications in batch production-based plants, traceability remains challenging to achieve in continuous …

An Improved United-Atom Potential For Molecular Dynamics Simulation Of Saturated Properties Of N-Alkanes, Wazih Tausif, Jordan Hartfield, Alex George, Zhi Liang

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Multiple united-atom (UA) potential models have been developed in the literature to reproduce experimental saturated properties of n-alkanes using Monte Carlo simulations. When these UA potentials are employed in molecular dynamics (MD) simulations, MD simulations often give relatively poor predictions of saturated properties of n-alkanes, particularly the saturated vapor densities, due to the challenges in accurate calculation of long-range intermolecular forces beyond the cutoff distance in an inhomogeneous system. In this work, a new set of UA Lennard-Jones (LJ) interaction parameters for n-alkanes is proposed to reproduce the saturated properties, including saturated liquid and vapor densities (ρ_f and ρ …

Performance, Economic And Environmental Evaluation Of A Solar-Assisted Vacuum Deaeration Heating System., Liew Shan Kun

Student Works (2020-2029)

This research evaluates the performance of a solar-assisted heating (SAH) system for makeup water in a vacuum deaeration process. The system integrates solar energy into the heating process, with parametric analysis conducted across varying configuration of total solar radiation and water flow rates. The total solar radiation at the experimental site in Kuala Kangsar, Perak, Malaysia, characterized by tropical weather, fell within the range between 414W/m2 to 568W/m2. Performance analysis showed that a flow rate of 0.4 LPM achieved the target temperature of 61°C required for the deaeration process. Thermal efficiency peaked at 62.60% under a solar radiation of 900 …

Aerodynamic Forces In Water And Air With Changing Wing Geometry, Michael Anthony, Carson Running

Mechanical Engineering Student Publications

This paper is an exploration of how the effects of wing geometry on the lift and drag in both air and water. The purpose of these findings is to understand if there exists a foil geometry that would offer the best lift-drag ratio in both fluids. To find the answer, chamber, chord, span, and aspect ratio were adjusted in an attempt to maximize lift and drag. The calculations were done through Matlab and the results are shown through Matlab figures. The Matlab code created shows that symmetric airfoils have the greatest lift to drag ratios due to their lower drag …

V-22 Osprey Proprotor, Derek Krieger, Carson Running

Mechanical Engineering Student Publications

This paper covers an aerodynamic analysis of the Boeing Bell V-22 Osprey proprotor blade by utilizing thin-airfoil theory (TAT) and lifting-line theory (LLT). The primary focus is how the coefficient of lift and induced drag respond to changes in the angle of attack of the proprotor blades. The proprotor blade is modeled as a finite wing based on the NACA 63-212 airfoil. The wing has a geometric twist of -35 degrees from root to tip. The theories used to evaluate the blade design are limited by the assumption of incompressible, inviscid flow. The results of the analysis indicate that lift …

Aerodynamic Analysis Of The Constrained Naca 8412 Airfoil For Formula Sae Application Using Thin-Airfoil And Lifting-Line Theories, Trevor Fried, Carson Running

Mechanical Engineering Student Publications

This project applies Thin-Airfoil Theory (TAT) and Lifting-Line Theory (LLT) to evaluate the aerodynamic characteristics of the inverted NACA 8412 airfoil as a single-element rear wing for Formula SAE. The 2D analysis was validated against XFOIL (Re = 480,000), confirming a zero- lift angle of αL=0 = -8.326° and establishing a viscous limit of cl,max ≈ 1.90 at αstall ≈ 13.0°. The 3D LLT model quantified the induced drag (CD,i), demonstrating that the wing's low aspect ratio and rectangular planform reduce efficiency compared to elliptic loading, with the induced drag being the dominant total drag component at high angles of …

Reinforced Scan: A Reinforcement Learning Enabled Optimal Laser Scan Path Planning In Laser Powder Bed Fusion Additive Manufacturing, Chaoran Dou, Jihoon Chung, Raghav Gnanasambandam, Yuhao Wu, Jianzhi Li, Zhenyu James Kong

Manufacturing & Industrial Engineering Faculty Publications

Additive Manufacturing is an innovative technology that fabricates parts layer by layer. However, in Laser Powder Bed Fusion (LPBF), printed metal parts often exhibit residual stresses, deformations, and other defects due to non-uniform temperature distribution during the printing process. To mitigate these issues, an optimized scan sequence within each layer can improve thermal uniformity. Traditional optimization methods, which rely on domain knowledge and employ trial-and-error or heuristic approaches, often fail to achieve optimal solutions due to the complex nature of the problem. One major challenge in improving scan strategies lies in the vast search space required to optimize the scan …

In Situ And Operando Microscopy Studies On Lithium Metal Anodes: A Review, Ian Lindsey, Cameron Mondl, Xiangbo Meng

Mechanical Engineering Faculty Publications and Presentations

Lithium metal is regarded as an ultimate anode for rechargeable batteries, ascribed to its extremely high capacity. Its implementation can remarkably boost the energy density of the resultant lithium metal batteries. However, it is very challenging to commercialize lithium metal anodes, primarily due to the intertwined nature of the formation of a solid electrolyte interphase (SEI) and the growth of lithium dendrites. To understand these issues and therefore develop technical solutions, various instrumental techniques have been employed. This review highlights the most recent advancements of in situ and operando microscopy studies that are critical for investigating and addressing the issues …

Crystal Structures, Optical Behavior, And Magnetic Properties In Hydrated Lanthanide Iron Sulfates, Chole Jones, Silu Huang, Tyler L. Spano, Eric A. Gabilondo, Mohammed Al-Fahdi, Kara Trim, Mary Douglas, Rongying Jin, Andrew Miskowiec, P. Shiv Halasyamani, Ming Hu, Jie Ling

Faculty Publications

Single crystals of LnFe(SO₄)₃(H₂O)₂ (Ln = La, Ce, Pr, Nd, Sm, Eu, Gd, Dy, Ho, Er, Tm; compounds 1–11) and LnFe(SO₄)₃(H₂O) (Ln = Tm, Yb, Lu; compounds 12–14) were synthesized under hydrothermal conditions. Single-crystal X-ray diffraction (SCXRD) analysis revealed that the dihydrated compounds (1–11) crystallize in centrosymmetric (CS) structures, with the lanthanide ions adopting eight-coordinate geometries. In contrast, the monohydrated compounds (12–14) exhibit noncentrosymmetric (NCS) structures, where the lanthanide ions are seven-coordinated. Vibrating sample magnetometry (VSM) confirmed that compounds 2, …

Fatigue Crack Length Estimation Using Acoustic Emissions Technique-Based Convolutional Neural Networks, Asaad Migot, Ahmed Saaudi, Roshan Joseph, Victor Giurgiutiu

Faculty Publications

Fatigue crack propagation is a critical failure mechanism in engineering structures, requiring meticulous monitoring for timely maintenance. This research introduces a deep learning framework for estimating fatigue fracture length in metallic plates through acoustic emission (AE) signals. AE waveforms recorded during crack growth are transformed into time-frequency images using the Choi–Williams distribution. First, a clustering system is developed to analyze the distribution of the AE image-based dataset. This system employs a CNN-based model to extract features from the input images. The AE dataset is then divided into three categories according to fatigue lengths using the K-means algorithm. Principal Component Analysis …

Improved Performance Of Wave Energy Converters And Arrays For Wave-To-Onshore Power Grid Integration, Madelyn Veurink, David Wilson, Rush Robinett, Wayne Weaver

Michigan Tech Publications

This paper focuses on power grid integration of wave energy converter (WEC) arrays that minimize added energy storage for maximizing power capture as well as smoothing the oscillatory power inputs into the grid. In particular, a linear right circular cylinder WEC array that implements complex conjugate control is compared and contrasted to a nonlinear WEC array that implements an hourglass buoy shape while both are integrated into the grid utilizing phase control (i.e., relative spacing of the WEC array) on the input powers to the grid. The Hamiltonians of the two WEC systems are derived, enabling a direct comparison of …

Spectroscopic Investigations On Polyvinylidene Fluoride Nanofibers, Parinaz Amaniabdolmalaki, Jui Vitthal Kharade, Alexandro Trevino, Lydia Morales, Karen Lozano, Victoria Padilla, Karen S. Martirosyan, Horacio Vasquez, Mircea Chipara

Physics & Astronomy Faculty Publications

The production of polyvinylidene fluoride nanofibers by force-spinning from polymer solutions was confirmed by electron microscopy. The structural and phase characteristics of the resulting nanofiber mats were examined using Fourier Transform Infrared Spectroscopy in Attenuated Total Reflectance mode, Raman spectroscopy, and X-ray Diffraction. Results from all these techniques consistently indicated that both the powder and the mats of polyvinylidene fluoride predominantly contain the α phase, with a small admixture of the β phase. Within experimental errors, no other phases were noticed both in the powder and in the as-obtained mats. The ratios of the areas of the Raman lines at …