Engineering Commons^™

Temperature Distribution And Thermal Stresses In Radiation-Cooled Circular Cylinders, William E. Putman Jr.

Mechanical Engineering ETDs

This study involves the determination of the transient temperature distribution and thermal stresses in a solid circular cylinder cooled by thermal radiation. The analytical solutions are presented in dimensionless form. Theoretical results are shown for temperature distribution and thermal stresses in the nondimensional form. Certain of these results are given in the dimensional form for the model cylinder used in this investigation.

The uranium-zirconium prototype element was thought to be undesirable for this investigation. Therefore, similitude was used to select a model which could be used for the experimental work. A solid, cylindrical, epoxy model was constructed, and thermocouples were …

Generalized Programs For Heat Transfer Analysis., Ceylung Chu

Masters Theses

"This report presents numerical methods for calculating temperature distributions in any physical system in which heat transfer is taking place. The syste.11 may be at either a steadystate condition or a transient condition. The temperature distribution may itself be or primary interest, or it may be used further to calculate the flow or heat or thermal stress.

The system under investigation is divided into a certain number of subdivisions, or so-called "regions". A reference point (node point) will be taken as representative for the region which includes that point. The temperature at the "node point11 is taken to be the …

Experimental Evaluation Of Thermal Stresses On The Outer Surface Of A Thick-Walled Tube., Vinodray T. Patel

Masters Theses

"In this investigation an attempt has been made to measure thermal stresses on the outer surface of a thick- walled tube. The inside surface was heated by steam passing through the tube while the outer surface was cooled by water. Two temperature compensated strain gages were used to measure strains in the tangential and axial directions respectively. The advantage of using this type of strain gage is to avoid the use of a dummy gage to compensate for the temperature effect.

The analytical solution to the problem was derived and the values of thermal stresses were calculated theoretically and compared …

A Simplified Mulesing Crush, G T. Halpin

Journal of the Department of Agriculture, Western Australia, Series 4

DURING the last two years Mr. Tom Flanigan, a mulesing contractor in a large area centred at Katanning, has performed the mules-tailstrip operation on many thousands of lambs and sheep.

Opposed Disc Plough Furrows Hard Kimberley Soils, Department Of Agriculture, Western Australia

Journal of the Department of Agriculture, Western Australia, Series 4

THE work of reclaiming the eroded areas of the Ord River catchment has posed special problems for field staff of the Department of Agriculture engaged on this large scale project.

Thousands of miles of furrows must be contour-ploughed and seeded in extremely hard ground over big areas of eroded country.

The Effects Of Granular Size On The Thermal Conductivity Of Sand, Kanubhai M. Patel

Masters Theses

"The thermal conductivity of granular materials can be determined by the Thomas method. This method was used here to determine the effects of granular size on the thermal conductivity of sand. A river sand was secured and screened. The sand retained between the Tyler Standard Screen Scale, mesh 10 and 14, 14 and 28, 28 and 40, 40 and 48, 48 and 60, and below mesh 60, was used for tests.

The thermal conductivity for the above six samples obtained by the author coincide fairly well with published data.

It is reported in the International Critical Tables that the thermal …

A Determination Of The Theoretical Stresses In A Deep Beam., James William Tritz

Masters Theses

"This paper presents an analytical solution of the stress distribution in a deep beam of finite length. The beam being considered is analyzed as one of plane stress. The method employed superimposes two stress functions each of which is a trigonometric series. The first stress function satisfies all boundary conditions except that of zero stress on the vertical faces. The second function is found, so that, when combined with the first function, all boundary conditions are satisfied. The IBM 1620 digital computer is then used to find the stresses for a particular beam. The results of this analysis are then …

Test 864: Wagner Fwd Wa4 (Diesel), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 862: Minneapolis-Moline U302 (Gasoline), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 867: Zetor 4011 (Diesel), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 865: Case 750 (Diesel), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

The Importance Of Radiation As A Means Of Controlling Surface And Internal Temperatures Of A Semi-Infinite Solid, Kenneth C. Woodruff Jr.

Masters Theses

"This problem is concerned with the temperature history of a semi-infinite solid bounded by one flat surface.

Heat was applied by convection from a hot fluid to the flat surface of the solid which was originally at a uniform temperature. Heat was radiated from the flat surface to black space and conducted into the solid according to Fourier's law. The temperature at the surface, and at several points beneath the surface, was determined as a function of time.

A method for solution of such a problem is demonstrated here by the use of numerical analysis and the Royal McBee LGP …

Test 868: Case 1200 (Diesel), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 873: Oliver 1650 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 874: Oliver 1650, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 875: Oliver 1850, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 869: Oliver 1850 Diesel 4wd, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 871: Oliver 1950 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Influence Of The Heat Release On Thermodynamic Characteristics Of Diesel Engines., Shirish Amritlal Desai

Masters Theses

"A Diesel. engine is an internal. combustion engine in which the fuel. is ignited by the heat of compression. Thus, the Diesel. engines are known as compression-ignition (C.I.) engines. The engine received its name: from its inventor, Dr. Rudolf Diesel., who in 1893 published a book under the title, '' Theory and Construction 0£ Rational. Diesel Engine". The first successf'u1 Diesel. engines, using liquid: fuel., which was injected into the cylinder by a blast of high-pressure air, were manufactured by the M.A.N. Company of Germany in 1895"-- Introduction, p. 1

Test 863: Minneapolis-Moline U302 (Lpg), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 866: Zetor 2011 (Diesel), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 870: Oliver 1850 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 872: Oliver 1950 Diesel 4wd, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 876: Oliver 1850 4wd, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Thermal Resistance Of Bonds And Contacts, David Marion Lewis

Masters Theses

"The adhesive and sealant Industry has more than kept pace with our rapidly expanding technology of today. This growth has left the standardization of data on adhesives far behind and lack of this data is obvious. Of the many applications, particularly as related to space technology and energy conversion, the resistance to the flow of heat offered by the bond layer is of considerable importance.

Little information is available on the effect of adhesives on heat transfer. In connection with their work on honeycomb panels, Rankle, Gier, and Bevans (7) determined the thermal resistance of the particular type of adhesives …

Forced Convection Heat Transfer Coefficients And Induction Heating, Max Edwin Light

Masters Theses

“The purpose of this study was to design and build an apparatus to experimentally determine the convective heat transfer coefficients for water flowing in a horizontal tube at turbulent flow. Also it was planned to use the apparatus to investigate the spatial dependence of energy deposition by induction heating.

An instrument and measuring techniques were developed that gave reasonable correlations between experimentally determined heat transfer coefficients and values calculated from generally accepted heat transfer relationships developed by other experimenters. Most of the calculated values were within ± 10% of the experimental values for a wide range of flow rates.

It …

The Design, Construction, And Evaluation Of A Vortex Stabilized Plasma Generator, Ronald Ray Williams

Masters Theses

“This report presents the design, construction, and evaluation of a vortex stabilized arc plasma generation facility operating on argon.

The facility consisted of five basic systems; the plasma genera- tor, the electrical power system, the argon flow system, the cooling system, and instrumentation.

The facility was designed to meet four general requirements; stable arc operation, low electrode deterioration, low cost of construction, and provisions for determination of the operating characteristics and thermal properties of the plasma.

Experimental results obtained in the laboratory agreed well with the design conditions. The rate of energy dissipated in the electric arc varied from 7. …

The Design, Construction, And Calibration Of An Angular Accelerameter., Walter Earl Palm

Masters Theses

"The purpose of this work was to design, construct, and calibrate an angular accelerometer for continuous operation. The design uses four symmetrically placed springs connecting a ring and hub. Strain gages are mounted on the springs in a Wheatstone bridge arrangement. When the entire unit is subjected to an angular acceleration, the ring deflects causing an output voltage. This voltage is proportional to the deflection which is shown to be a function of the angular acceleration. The accelerometer was constructed to operate at frequencies up to 120 cps. The calibration was accomplished by using a simple harmonic motion input"-- Abstract, …

Theoretical Investigation Of Steam Jet Cleaning, Jaswant T. Lotwala

Masters Theses

"Steam cleaning methods are used by industries to remove mass of dirt and grease deposits from machine parts and other surfaces. It is necessary to know the rate at which this mass can be removed from a surface. The present investigation was made to determine this rate of mass removal. The mass transfer rate is influenced by two phenomena; namely, heat transfer and momentum transfer. Both of these were discussed and the results obtained from the analysis were used in determining the total mass transfer rate. The effects of various parameters, such as density and velocity of the cleaning fluid, …

The Effect Of An Induction Field On Transducers., Ratilal S. Patel

Masters Theses

"This report presents the results of an experimental investigation on the effect of an induction field on transducer output. Various types of transducers; strain gages, thermocouples, and thermistors, were used. The changes in the output of these transducers were measured for various induction field conditions.

Measurements must often be made where strong electrical fields are present. Strain gages are used to measure the stresses in electrical machinery. Thermocouples and thermistors used for measuring the temperature of materials undergoing heat treatment with an induction heater are also subjected to an induction field.

The general experimental procedure was the same throughout the …