Engineering Commons^™

Test 887: Allis-Chalmers 190 Xt (Diesel), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 889: Ford 3000 4-Speed (Gasoline), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 893: Ford 4000 8-Speed (Diesel), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 900: Massey-Ferguson Mf 180 (Diesel), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 929: Allis-Chalmers 190 Xt (Gasoline), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT

GENERAL CONDITIONS

East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers.

PREPARATION FOR PERFORMANCE RUNS

The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 894: Ford 2000 8-Speed (Gasoline), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

The Eccentric Orifice As A Flow Measuring Device In Small Diameter Pipes, James E. Casale

Masters Theses

"This thesis reports and evaluates the use of an eccentrically placed orifice as a flow measuring device in small pipe sizes. The orifice is placed in a concentric location and moved to increasingly eccentric locations until full eccentricity is reached. At full eccentricity the circumference of the orifice is tangent to the circumference of the pipe. The effects of increasing eccentricity are evaluated for four orifices...Flow coefficients for the orifices in different locations are plotted against Reynolds numbers. The eccentric orifice is a reliable, accurate flow measuring device for metering or controlling the flow of fluids. Design criteria can be …

Analysis Of The Flow Characteristics Through A Water Pressure Regulator, Anthony Lee Jatcko

Masters Theses

"This thesis presents an analysis of the flow characteristics through a water pressure regulator. Characteristic curves of the relationship between pressure drop through the regulator and flow through the regulator are developed. To further analyze these relationships, a least squares computer analysis was used to develop equations to fit these curves. An investigation into the modes of dissipating pressure energy in this type of regulator tends to indicate that a significant portion of the energy is lost through viscous shearing action in the area of high turbulence. The aforementioned characteristic curves also showed definite critical pressure points in the form …

Application Of The Photoelastic Coating Method To Evaluate The Stress Distribution On The External Surface Of The Cap Of An Electrical Insulator, Harijeetsinh Jagtiani

Masters Theses

"The Photoelastic Coating Method was applied to find the surface stresses on the cap of an electrical insulator. The strain distribution was observed and photographed. This color photograph indicated a visible geography of the maximum shear strain distribution in the region of the insulator where the birefringent plastic was bonded with a reflective cement. The Oblique Incidence technique was used to determine the principal stresses from the maximum shear strain (or the principal strain difference) readings, obtained from Normal Incidence. The critical cross-section of the insulator head was optically located, giving an initiative for the re-design of the insulator cap. …

A Study Of The Non-Newtonian Turbulent Fluid Flow Through An Annulus, Yogesh R. Parikh

Masters Theses

"This investigation is concerned with the study of non-Newtonian flow through an annulus. The experimental analysis of incompressible non-Newtonian fluids in a long cylindrical annulus of radius ratio 0.375 was studied in the turbulent region. Different types of non-Newtonian fluids were used to procure flow behaviour for the annulus.
The effect of increasing flow rate of the non-Newtonian fluids was evaluated by gathering pressure drop data across the annulus using a differential manometer. The power-law model is used in this study to characterize the non-Newtonian flow. The parameters of the power-law model were evaluated by gathering viscometric data on a …

Optimization Of Flywheel Design For Internal Combustion Engines, Dady Jal Patel

Masters Theses

"A new approach to the problem of flywheel design has been developed, thus eliminating some of the problems of conventional design. The term flywheel design, in this thesis, refers to the determination of the flywheel inertia (mass moment of inertia) only. Two versatile computer programs were set up to obtain the flywheel inertia and the turning moment diagram for a large variety of internal combustion engines, and use was made of these programs to optimize the inertia of the flywheel with respect to speed. As an illustration the data of a 1960 Corvair engine were selected, and the results obtained …

Instrumentation Of A Diesel Engine For Measuring Cylinder Head Temperature, And Pressure At Various Crank Angles, Raman A. Patel

Masters Theses

"In this investigation, an attempt has been made to measure the instantaneous pressures in the cylinder and the transient temperatures of cylinder head versus crank angle in a Diesel engine. A strain-gage pressure transducer and a sensitive surface thermocouple were used. The pressure transducer was practically free from temperature influence and strain effects caused by installation. It had a greatly reduced sensitivity to vibrations compared with other available types of pressure transducers. The thermocouple had a very short response time. A device enabling very accurate measurement of crank-angle was constructed. Appropriate quantities were displayed on the screen of an oscilloscope …

A Study Of Radiation Heat Transfer In Rectangular Ducts And Enclosures, Jenn-Wuu Ou

Masters Theses

"The purpose of this study is to determine the radiant heat transfer in rectangular configurations and construct a general computer program. Two specific cases are studied in this work. The first case is a rectangular duct with openings at each end. The duct is separated into two sections which are called the source and the sink respectively. A linear temperature profile is imposed on the source section. The energy loss of both the source and the sink is investigated. The second case is a complete rectangular enclosure. The two end plates are called the source and the sink respectively. A …

Free Convection Heat Transfer From An Inclined Heated Flat Plate In Air, Shu Chien Yung

Masters Theses

"An experimental investigation has been performed to determine the free convection heat transfer from a heated flat plate in air moved from the vertical position through three inclined positions to the horizontal position. The hot surface of the plate was facing downward for the horizontal and three inclined positions. Tests were performed at plate surface temperatures from 120°F up to 404°F. Data for the plate surface temperature at about 165°F with the plate in the vertical position agrees very well with previous experimental work. This same data was used to determine a new parameter, introduced into the Pholhausen free convection …

An Apparatus To Measure Capillary Jet Thrusts And The Evaluation Of Normal Stresses In Fluids, Charles Donald Green

Masters Theses

"The purpose of this work was to design, construct and calibrate simple, inexpensive apparatus which could be used to measure the normal stresses and tangential shear stresses of a fluid. For normal stress measurements, the capillary jet thrust principle was selected. A standard analytical balance was modified so that capillary tubes could be fitted on it horizontally. It was designed so that the thrust produced by a jet of fluid from the tube caused a deviation from the zero balance position. The weights needed to rezero the balance gave a measure of the thrust"--Summary, page 1.

Temperature Distribution In Thermal Boundary Layers (In Free Convection) Using A Modified Schlieren Method, Philip Ling Chen

Masters Theses

"A simple optical apparatus, the Schlieren interferometer, was constructed for the quantitative investigation of free convection heat transfer from solid bodies. The photographic results, checked by using thermocouples, were used in evaluating the temperature distribution, the key to the solution of these problems. Interpretation of the photographic results was made using the simple calculation for the conventional interferogram and the Dale-Gladstone law. Although the experiments were limited to a heated flat plate and a heated wire, two dimensional test pieces of irregular configuration can be investigated by the same apparatus with simple modifications. The photographs of the conventional Schlieren, the …

The Development And Evaluation Of An Experimental Technique To Determine Stress Distribution In Uniformly Loaded Flat Plates, James William Walker

Masters Theses

"This thesis reports and evaluates an experimental technique that was developed to determine and monitor the stresses in a simply supported, uniformly loaded circular plate. Deflections are less than half the thickness of the plate. The application of the developed technique to plates whose integrity has been compromised with holes in various locations is discussed.

Resistance strain gages were used to determine experimentally the stresses in a simply supported, uniformly loaded circular plate with and without a concentric hole. The accuracy of the experimental results was established to be within approximately six percent of theoretical.

Proper application of the experimental …

Determination Of The Temperature Distribution Of The Ionized Portion Of The Jet From A Vortex Stabilized Plasma Generator Operating On Argon, G. Douglas Schellman

Masters Theses

"The interim thesis deals with the determination of the temperature distribution of a plasma jet operating on argon. It is the purpose of this thesis to present in detail the experimental process used and make a correlation of the experimental and theoretical results.

A copper enclosure was placed around the protruding flame, and the embedded thermocouple readings were taken and recorded. A stagnation temperature probe was inserted in the enclosure and moved both axially and transversely toward the flame taking readings at each pre-chosen interval. The exit temperature of the jet was obtained from a total energy balance.

From the …

The Design And Construction Of A Shock Tube Facility, William Adolph Crede

Masters Theses

"It is the object of this thesis to give an account of the considerations necessary to design, construct, and operate a shock tube facility.

The primary purpose of the facility was to provide a means to study high strength shock waves in physics, chemistry, and aerodynamic applications.

Preliminary designs were undertaken to determine the basic dimensions and related capabilities. Final design, construction and testing of the tube itself was performed by Nooter Corporation in St. Louis, Missouri. Preliminary designs agreed rather closely with final construction.

Experimental testing was confined to the successful operation of all the various components of the …

Turbulence In Journal Bearings, Kashyap R. Mehta

Masters Theses

"In this investigation, an experimental study was performed on a journal bearing under laminar and turbulent flow conditions. Using relationships for friction factor developed previously by other investigators a comparison was made with results of this present investigation. Since the flow changes from laminar to turbulent with a change in speed of rotation, curves for friction factor as a function of speed were plotted. Various attempts to make the recording and measuring systems more sensitive were also made and are discussed in this thesis"--Abstract, page ii.

Heat Transfer Coefficients Across Bonds And Contacts, Eugene Charles Fadler

Masters Theses

"The purpose of this investigation was to experimentally determine heat transfer coefficients across interfaces, including the effects of the thermal conductivity of the adherends, the hardness of the adherends, the bond thickness, and the type of adhesive.

Aluminum alloy, steel, copper, and extruded nylon rods were used as adherends; all 1.875 inches diameter and 8 inches long. Each was cut radially at its midpoint and faced off to the desired surface finish. Bare interface tests were conducted before the adherends were bonded together. The adhesives used were high grade silica refractory cement, two-part epoxy resin adhesive, and thermosetting synthetic rubber-phenolic …

A Photoelastic Study Of The Effect Of Certain Geometric Variables On The Plane Stress Distribution In An Electrical Insulator Body, Richard L. Pendleton

Masters Theses

"Photoelastic models were used to indicate stress patterns in various geometrically designed shapes. Each model represented a two-dimensional cross-section of the interior portion of an axially symmetrical porcelain electrical insulator. Five different loading pins were combined with three loading heads to produce eleven models. The maximum stress in each model was determined using a photoelastic method of stress analysis. An attempt was made to select the best structural design to be used in an electrical insulator. The test results indicate that the most desirable stress distribution is obtained using a single step loading pin and that the loading head angle …

The Design And Construction Of An Instrument For Calibrating Accelerometers, Richard Rabenau

Masters Theses

"The purpose of this work was to design and construct a facility to calibrate accelerometers. A ceramic piezoelectric shaker and modified Michelson interferometer together with necessary electronic equipment were used. The system produced accurate and stable acceleration at five discrete points from 1,000 to 5,000 cycles per second. the maximum calibration levels were approximately 50 g's"--Abstract, page ii.

Test 877: Ford Commander 6000 (Gasoline), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 896: Massey-Ferguson Mf 165 (Diesel) (Also Mf 165 8-Speed Diesel), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 899: Massey-Ferguson Mf 135 (Gasoline), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Stresses In Thick Slabs Subjected To Thermal Loadings., Robert I. Brasier

Mechanical Engineering ETDs

The use of thick, reinforced concrete components in nuclear reactor constructions where they serve as both structural and shielding components has become commonplace. In use, the concrete ls subjected to mechanical loads due to the weight of various reactor components and thermal loads due to tempera­ture gradients and internal heating due to absorbed radiation. Since these components are required to maintain their structural integrity for long period of time under fluctuating temperature gradients their stress analysis is a vital problem. Typical components range from thick slab shields to complete reinforced con­crete pressure vessels. It is felt that current criteria for …

Simultaneous Development Of Velocity And Temperature Profiles In The Annulus With Laminar Flow And Both Walls At Constant Temperatures, Stephen Lothair Ritchie

Theses and Dissertations

Forced convection heat transfer in the entrance region of tubes and ducts has been studied extensively since the pioneering work of Graetz. Most of the published solutions for axial flow heat transfer are based on the idealization of either fully established or uniform velocity profiles with developing temperature.

Analysis And Discussion Of The Effect Of Heat Loss From The "Insulated" Face Of Thin Foil Heat Flux Meters, Mont Johnson Stevens

Theses and Dissertations

The object of this work was to investigate the effect that heat losses from the "insulated" face of thin foil heat flux meters has upon the sensitivity of heat flux meters. In the past it has been characteristic of any analysis done on heat flux meters to assume that the insulation on the back face of the foil was a perfect insulator and thereby neglect the effects of heat losses from this "insulated" face. It is hoped that the information given in this thesis will be of value in determining how the geometric and heat transfer parameters affect the operation …

Investigation Of Aerodynamic Hysteresis, Gerald Heber Peterson

Theses and Dissertations

The word hysteresis is derived from a Greek word meaning "to lag 'behind". As specifically applied to fluid flow around bodies with transient angles of attack in and near the stall region, "aerodynamic hysteresis" is used to describe the effect of delay in boundary layer separation and reattachment upon the lift, drag and pitching moment. Experimental work done on airfoils by H. Studer showed that for increasing angles of attack flow "separation is delayed to an angle of attack appreciably greater than that for a stationary airfoil. On the return movement, re-establishment of a smooth flow is also delayed." [1]* …