Engineering Commons^™

Deposition Of Suspensions In Laminar Flow In The Entrance Region Ofa Channel And In A Diffuser, Shawki Mahmoud Eldighidy

Dissertations

In this investigation, the deposition of suspensions in laminar flow in the entrance region of a channel and a diffuser was considered.

The particulate phase was considered to he under the action of the electric field force clue to electrostatic charges. In addition, a lift force acting on each particle at the wall arising from the fluid shear near the wall and an adhesive force between each particle and the wall due to the difference of the material properties for both particle and walls were considered as surface forces.

The suspension flow was assumed to be incompressible, laminar, dilute, and …

Waviness Distortion In Mechanical Face Seals, Joseph J. Roesch

Mechanical Engineering ETDs

In this thesis the phenomenon of waviness distortion in mechanical face seal washers is investigated. Waviness in face seals leads to leakage in some applications. When leakage becomes significant, the seal must be replaced. If the distortion causing mechanism can be described, improvement in seal performance and behavior may be possible.

The components and function of the mechanical face seal are first discussed. It is seen that only one component of the seal unit shows significant deterioration over a period of time. It is also seen that this component, the face washer, wears in a characteristic manner. The characteristics of …

Steady State Fluidics: The Static Matching Of Fluidic Amplifiers And Loads, Frank J. Redd

Theses and Dissertations

"Fluidics" is the title applied to a relatively new technology which is concerned with the control of fluid power and the processing of information through the use of the fluid mechanical properties of the fluid medium itself. The absence of moving parts and the relatively low sensitivity to enviromental conditions suggest the probability that fluidic systems will prove to be faster and more reliable than the mechanically controlled (valves, diaphragms, springs, etc.) fluid systems which they are designed to replace.

Ua64/3 Readout, Wku Industrial Education & Technology

WKU Administration Documents

Newsletter includes articles:

• New Departmental Programs
• Crisp, Jeff. Vocational-Industrial & Technical Teacher Education CBTE Project
• Lyons, Jerry. Not a Dirty Word, re productivity
• Conley, Frank. Comment, re: scholarships
• Dye, Wandel. Airbrush Rendering
• Student Chapter of SME Formed
• New Equipment Inventory
• Nalbach Demonstration Highlights Semester
• Environmental Science & Technology Building
• Industrial Technology Lecture Series

Ole Miss Engineer 1975

Ole Miss Engineer

No abstract provided.

Analysis Of Spread Multi-Jet Vtol Aircraft In Hover, Leroy F. Albang

Mechanical & Aerospace Engineering Theses & Dissertations

An investigation of VTOL aircraft lift losses in hover has been conducted to evaluate a method for a simplified test technique. Three flat plate models were tested to determine their usefulness in predicting hover characteristics by comparing results between plate and three­ dimensional models. Attempts to correlate the out of ground effect results for the plate models with the empirical expression for calculating jet-induced loads were successful for the models which used engine simulators producing efflux characteristics similar to the three­ dimensional model engines. Data for the model using engine simulators with characteristics unlike those of the three-dimensional model simulators …

A Method For Improving The Accuracy In Phase Change Heat Transfer Data Through Increased Precision In Thermophysical Property Determinations, John Philip Drummond

Mechanical & Aerospace Engineering Theses & Dissertations

Wind tunnel model materials typically have thermophysical properties that vary with both position and temperature. A numerical study using a finite difference representation of the heat conduction equation has been performed on several of these model materials to determine their thermal response under a specified heat loading. This study has confirmed the feasibility of using an effective thermophysical property to account for the existence of variable thermal properties when a model undergoes aero­ dynamic heating. The effective property, when used in the reduction of phase-change heat transfer data, forced agreement of the actual transient behavior of a model with the …

Effect Of Rod Gap Spacing On A Suction Panel For Laminar Flow And Noise Control In Supersonic Wind Tunnels, William D. Harvey

Mechanical & Aerospace Engineering Theses & Dissertations

It has been well established that the test section flow of conventional supersonic and hypersonic wind tunnels contains significant levels of disturbances. These disturbances are mainly caused by the radiation of aerodynamic noise from the turbulent boundary layer on the nozzle walls. This noise level has been shown to have an important effect on boundary layer transition measured on models in tunnels. The purpose of this thesis is to present results of a coordinated experimental and theoretical study of a sound shield concept which aims to provide a means of noise reduction in .the test section of supersonic wind tunnels …

An Experimental Investigation Of A Cold Jet With Solid Centerbody Emitting From A Flat Plate Into A Subsonic Free Stream, Danny K. Livingston

Mechanical & Aerospace Engineering Theses & Dissertations

A study of the influence of a solid center body on lift loss and pitching moment has been conducted. It has been well established that a round free jet emitted from a flat plate at right angles to a cross flow causes an induced pressure distribution on the plate which adversely affects the lift and pitching stability of the flat plate.

This investigation has employed a 2.58 - cm diameter round jet with a 1.91 - cm diameter solid rounded core in order to modify the induced flow field and attempt to reduce the lift loss and pitching moment. Preliminary …

Alcohol Assisted Hydrocarbon Fuels: A Comparison Of Exhaust Emissions, Power Output And Fuel Consumption Using Static And Dynamic Engine Test Facilities, Dwight J. Bushnell

Theses and Dissertations

America’s energy crunch— something new for a country that has been used to great affluence. America’s smog— an eye stinging, lung burning situation which the Environmental Protection Agency has "promised" to rectify. These are two outstanding problems that face the engineer and scientist of today. The end of the era of cheap gasoline has brought the beginnings of a quiet revolution to Detroit: an improvement in the efficiency, economy and emission level of the American automobile. Word has penetrated to the automotive engineers that the emissions level, fuel economy and automobile safety are the prime design considerations for the automobile …

Computer Aided Structural Analysis: The Finite Element Method, Richard T. Ryner

Graduate Research Papers

The design process is a complex and tedious one. Within it, the task of design verification appears to require the lion's share of time, effort, and money involved.

The design formulation activity requires creative people, placed in an environment where they are able to formulate ideas which eventually become the manufactured products of an organization. This task takes up comparatively little of the time and effort of the design cycle. Therefore, it would appear that the greatest savings could be made in the design analysis task. Further, if these savings can be made earlier in the design cycle, in the …

Determination Of The Most Economically Feasible Method For High Volume Machining Of A Discharge Port In A Powder-Metal Compressor Cylinder, Perry W. Carter

Theses and Dissertations

The purpose of this study was to ascertain the most economically feasible method for high volume machining of a discharge hole in a power metal compressor cylinder.

Stresses At The Tips Of Cracks Emanating From The Loaded Fastener Hole, Venkataraman Shivakumar

Mechanical Engineering ETDs

Stress-intensity factors, K, are obtained at the tips of radial cracks emanating from the boundary of an internal circular fastener hole in a plate loaded by a pin or rivet that just fills the hole and is pulled in the negative y-direction, in the plane of the plate. Solutions are obtained in a conformally mapped region in the form of series for different crack lengths and are based on the Muskhelishvili formulation in the two-dimensional theory of elasticity. The method presents a general technique for determining K for k symmetrically located radial cracks of equal length for a wide variety …

Wave Induced Pressures On Submerged Plates, William W. Durgin, Jong C. Shiau

Office of the Provost Scholarship

The prediction of forces, or more precisely, the pressure distributions, experienced by submerged structures due to the passage of gravity waves has become important with the advent of large offshore structures. If the size of a structure is small compared to the wavelength then the forces can be evaluated by the assignment of suitable drag and inertia coefficients using an approach similar to that of Morison (6) in which case it is necessary to determine the coefficients experimentally for any given geometry (2). If the size of the structure is a significant fraction of the wavelength, the preceding method is …

Energy Efficiency And Conservation Of Building Hvac Systems Using The Axcess Energy Analysis Computer Program, Ronald H. Howell, Harry J. Sauer Jr.

UMR-MEC Conference on Energy / UMR-DNR Conference on Energy

This paper discusses the use of the AXCESS-UMR energy analysis computer program applied to two different buildings. The monthly and yearly energy requirements of many of the commonly used HVAC systems for a single-story multi-zone building are found and compared. Energy conservation techniques are also evaluated for a two-story St. Louis office building.

Creating The Electric Energy Economy, L. G. Hauser

UMR-MEC Conference on Energy / UMR-DNR Conference on Energy

My remarks will be directed to four points:

First, that energy is the life blood of our economy, and that its use or conservation is far from a simple matter of personal habits of waste or frugality. In other words, the vital role energy plays in the production of goods and services should be distinguished from its use in their consumption.

Second, that our excessive dependence on our two scarcest energy resources -- oil and natural gas -- is the core of the energy problem, both U.S. and worldwide.

Third, that limiting our time horizon to this winter, next summer, …

Control By Code Of Energy Usage In Building Systems, Harry J. Sauer Jr., Ronald H. Howell

UMR-MEC Conference on Energy / UMR-DNR Conference on Energy

Space heating, air-conditioning and refrigeration accounts for over 30% of the total energy use in the U.S. ASHRAE Standard 90P, ENERGY CONSERVATION IN NEW BUILDING DESIGN, sets forth requirements for the design of all types of new buildings, covering their exterior envelopes and selection of their HVAC, service water heating, electrical distribution and illuminating systems and equipment for efficient use of energy. This paper reviews the current status, content, and implications of the proposed energy standard and reports some experience with its use.

Centralized Solar Wind Home Heating, Russell Peterson, Duane Cromack

UMR-MEC Conference on Energy / UMR-DNR Conference on Energy

In the immediacy of national goals for energy independence, the need emerges to use dialectic methods to diminish the energy consumptive characteristics of the typical home.

At the cutting edge of resourceful progress are the residential developments which embrace alternative and conservative energy techniques. In conjunction with such a planned, low impact community, this paper proposes a cluster-centralized system which utilizes wind energy in combination with solar thermal energy for space and domestic water heating.

A description of the random solar-wind resource embodies a matching problem that in turn reveals the benefits of the combined mode of energy collection. Though …

Energy And Transportation Policy, James S. Sagner

UMR-MEC Conference on Energy / UMR-DNR Conference on Energy

Energy shortages of recent years suggest a re-examination of national transportation policy. The lack of a coordinated approach to the solution of urban cogestion inhibits potential short-run responses to gasoline shortfalls. Longer-range policy, particularly in the context of severe financial constraints, must be carefully integrated with demonstrated patterns of urban travel and population and employment densities. Given these considerations, metropolitan areas now planning or constructing rapid rail facilities may be selecting inappropriate responses to the problem of urban access.

Energy, Environment And Incremental Decision Making, Jeff V. Conopask, Robert R. Reynolds Jr.

UMR-MEC Conference on Energy / UMR-DNR Conference on Energy

During the late 1960's and early 70's a variety of environmental/energy oriented legislation was enacted by the Congress. The most important of these acts, the National Environmental Protection Act (NEPA), required that environmental impact statements be filed when various private and public activities have a potential for impacting man and his environment. (17) Impact statement requirements go beyond the currently practiced cost/benefit analysis, which is often just a production (direct) impact assessment. Heretofore, indirect or second round economic and social effects of consequence affecting other national goals were seldom counted.

The Design And Performance Of A Distributed Flow Water-Cooled Solar Collector, Donald L. Spencer, Theodore F. Smith, Herbert R. Flindt

UMR-MEC Conference on Energy / UMR-DNR Conference on Energy

Design of a flat plate collector which reduces the temperature differential between the absorber plate and the fluid is described. The reduced temperature differences are shown to yield increase collector performance. Flow characteristics of the collector are examined. Collector thermal performance is illustrated for typical operating and environmental conditions. A cost analysis is presented to demonstrate that material and assembly costs are substantially lower than for any collector presently on the market.

Status Report On The Callaway Nuclear Power Plant, A. E. Bolan, D. F. Schnell

UMR-MEC Conference on Energy / UMR-DNR Conference on Energy

The progress to date of the first nuclear-powered, electric generating plant proposed to be constructed in the state of Missouri is described.

Direct Ac Generation From Solar Cell Arrays, Fernando L. Alvarado, Adel H. Eltimsahy

UMR-MEC Conference on Energy / UMR-DNR Conference on Energy

Results of the investigation of the performance of solar cells when directly coupled to a conventional three-phase power network are presented. This approach dissociates the electricity production problem from the electric energy storage problem. Extensive studies of the required power inverter are performed. Preliminary simulation results indicate that ac power outputs of better than 90% of the optimum cell power output can be easily achieved by means of a suitably controlled inverter, thereby justifying the elimination of dc loads or local dc electric energy storage devices. It is also shown that the controlling policy for the inverter must depend on …

Dynamic Simulation For Regional Energy Studies, B. W. Jones, P. M. Moretti, J. H. Mize

UMR-MEC Conference on Energy / UMR-DNR Conference on Energy

A series of models has been developed for regional studies of energy supply- demand systems. The models are based on dynamic simulation of components of the system using equations derived from the technical details of the system. The models contain sufficient detail to make in-depth studies and specific recommendations. The final goal is to include all aspects of regional energy systems from native supplies of energy resources to the economic activities of the region.

To develop a comprehensive model, the system has been partitioned into subsystems, so that a detailed model can be made for each subsystem. The detailed model …

How Might Synthetic Fuels From Coal Affect Natural Resources And Environment?, H. J. Plass Jr.

UMR-MEC Conference on Energy / UMR-DNR Conference on Energy

Energy self-sufficiency for the U. S. requires substantially increased use of coal. Direct combustion of coal without adequate environmental controls, as would occur if coal were used as a fuel for homes and offices throughout the country, would result in severe air pollution problems„ Synthetic fuels from coal such as methane, low BTU gas, or hydrogen, when utilized by the homes and businesses as gas or as electricity from gas, will contribute a much smaller amount of air pollution. However, to make these synthetic fuels available, it is necessary to mine more coal than would have to be mined for …

Test 1185: S.A.M.E. Panter 4wd Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Alcohol Assisted Hydrocarbon Fuels: A Comparison Of Exhaust Emissions And Fuel Consumption Using Steady-State And Dynamic Engine Test Facilities, D. J. Bushnell, J. M. Simonsen

UMR-MEC Conference on Energy / UMR-DNR Conference on Energy

This paper presents experimental data which exemplifies the differences in emission level testing on internal combustion engines when dynamic engine tests are used instead of steady-state engine tests. A comparison of the two test methods is made using hydrocarbon fuels with varying amounts of methanol. Emissions measured include the nitric oxides, unburned hydrocarbons and carbon monoxide. Emission levels and fuel consumption are reported for the various volumetric percentages of methanol in the fuel.

Of special significance are the different trends the emission levels establish when subjected to a dynamic engine test as compared to the results for the steady-state tests. …

Test 1195: Allis-Chalmers 7000 Ps Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS Each tractor is a production model equipped for common usage. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operator station. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures must conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crankcase is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The fuel …

Test 1173: Massey-Ferguson 1805 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT

GENERAL CONDITIONS

East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers.

PREPARATION FOR PERFORMANCE RUNS

The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Growing Sunflowers In South-Western Australia, M L. Poole

Journal of the Department of Agriculture, Western Australia, Series 4

The oil produced from sunflowers falls into the "polyunsaturated" group and usually commands a premium price on world markets.

Some Western Australian farmers seeking to diversify their cropping programmes in the face of marketing difficulties for many agricultural products are trying sunflowers, although commercial production has not yet been achieved.

This article sets out some basic information for farmers wishing to try sunflowers.