Engineering Commons^™

Ole Miss Engineer 1986

Ole Miss Engineer

No abstract provided.

An Analytical And Experimental Study Of Clearance And Bearing-Bypass Load Effects In Composite Bolted Joints, Rajiv Vikas Arun Naik

Mechanical & Aerospace Engineering Theses & Dissertations

A combined analytical and experimental study is conducted to determine the effects of clearance and bearing-bypass loading for mechanically fastened joints in composites. A simple method of analysis is developed to account for the nonlinear effects of bolt-hole clearance. The nonlinear load-contact variations for clearance-fit fasteners are also measured using specially instrumented fasteners. For a quasi-isotropic graphite/epoxy laminate, results show that the contact arc as well as the peak stresses around the hole and their locations are strongly influenced by the clearance. After a slight initial nonlinearity, the peak stresses vary linearly with applied load. The typical clearance levels are …

An Experimental And Analytical Investigation Of Incompressible Fluid Flow Through A Distensible Tube System, Steven C. Wells

Mechanical & Aerospace Engineering Theses & Dissertations

An analysis was made of pressure and flow in a novel elastic tube system which has been used to theorize certain aspects of renal hemodynamic cs. Validation of the theory could alter the treatment of certain heart and kidney disorders. In an attempt to better understand a system flow anomaly under steady driving head conditions, experiments were performed, and a mathematical model was developed. The development of the model incorporated a set of nonlinear differential and algebraic equations. Using a finite-difference analysis as the method for obtaining a numerical solution, various pressures and flows were obtained. Results for the steady-state …

Three-Dimensional Elastic-Plastic Finite Element Analysis Of Fatique Crack Growth And Closure, Rahmatollah G. Chermahini

Mechanical & Aerospace Engineering Theses & Dissertations

The purpose of this study was to develop a three-dimensional, elastic-plastic, finite element analysis to investigate crack extension and closure under cyclic loading. The initial study concentrated on the behavior of a straight through crack in a finite-thickness plate subjected to tensile loading (middle-crack tension specimen). The finite element model was composed of 8-noded (linear-strain) isoparametric elements. In the analysis, the material was assumed to be elastic-perfectly plastic. Zienkiewicz's "initial-stress" method, von Mises' yield criterion, and Drucker's normality condition, under small-strain assumptions, were used to account for plasticity. The three-dimensional analysis is capable of extending the crack and changing boundary …

Test 1600: Valmet 148 4wd Turbo Diesel 12-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1599: Valmet 980 4wd Turbo Diesel 8-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1598: Kubota M8030dt And M8030 Diesel 16-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Column Froth Flotation, David C. Yang

Michigan Tech Patents

The froth flotation device includes a flotation column partially filled with a packing which defines a large number of small flow passages extending in a circuitous pattern between the upper and lower portions of the column. A conditioned aqueous pulp of a mineral ore, such as iron ore, is introduced into the midzone of the column. A pressurized inert gas, such as air, is introduced into the bottom of the column and is forced upwardly through the flow passages in the packing. As the air flows upwardly through these flow passages, it is broken into fine bubbles which intimately contact …

Test 1597: Kubota M7030dt And M7030 Diesel 16-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Modal Analysis Of A Cantilever Plate, Ohseop Song

Theses

This thesis discusses the vibration of a thin, flat cantilever aluminum plate. Results are based on both an analytical finite element method using the ANSYS program and an experimental analysis using a digital Fast Fourier Transform (FFT) analyzer. The FFT analyzer permits extraction of modal parameters (natural frequency, damping, mode shape) for the plate.

Introductory Guide To Bridgeport Series I Cnc Milling, Drilling And Boring Machine, Apurva Vinodchandra Doshi

Theses

This thesis is intended to serve as an easy introductory guide on how to work with Bridgeport Series I CNC Milling, Drilling and Boring machine. An attempt has been made to make the subject matter simpler to give the reader a good start in programming and operating this machine

The spectrum of technological implementation of CNC machine tools is extremely broad,. Companies utilizing advanced technologies such as computer graphics, DNC and Group Technology are in this field for some time. Even small shops are getting equipped with CNC machine tools. The present CNC systems, which are less costly, more reliable …

Thermal Energy Storage Using Phase Change Material With Multi - Melting Temperatures, Christakis Christodoulou

Theses

Three different models are developed in this investigation, for the study of thermal energy storage, using a phase change material with multi-melting temperatures. Using Model B as the basis, the developed partial differential equations are numerically solved by a finite difference method. Two computer programs were written based on that solution, one for the charging mode and one for discharging. Finally, using the computer programs, a set of results was obtained for both charging and discharging, utilizing calcium chloride hexahydrate as the phase change material with constant and multi-melting temperatures.

Isoparametric Finite Elements For Axisymmetric Solids, Ramanand R. Shetty

Theses

The finite element formulation of axisymmetric plane stress analysis is used to develop a computer program for numerical implementation. The basic relations used to derive the finite element equations for a solid continum are reviewed in the thesis. The programming organization is summarized and program list is given in Appendix.

The program portion for isoparametric elements are borrowed from Numerical Methods in Finite Element Analysis by K. J. Bathe and E. L. Wilson, and various other subroutines are used from Mr. Huang's thesis on Micropolar elasticity analysis. Mr. Huang's computer program is based on the work done by Dr. Nakamura …

On Radial And Rotational Spring Constants Of Piping With Square Tubing Attachment, Hson-Chih Sun

Theses

Numerical values and analytical expressions for spring constant in the radial direction, and rotational spring constants in the circumferential and longitudinal directions of piping with square structural tubing attachment are presented.

Following Bijlaard's approach, the double Fourier series solution for the thin shell equation are used to express these spring constants as a function of internal pressure, q, and pipe-structural tubing parameters, such as alpha (piping length/radius), beta (tube size/pipe dia.), gamma (pipe radius/thickness) and thickness of the structural tubing. Numerical results of these spring constants are presented in tabulated form. These Tables include a set of eight standard square …

Plate Stress Analysis By The Finite Element Method, Wen-Jung Chuang

Theses

The finite element formulation of plate elasticity is presented and is employed in the development of the formulation of element stiffness equations. The programming structures are also summarized.

The finite element program PLATE cited from Prof. J. N. Reddy's " An Introduction to the Finite Element Method " has been used to solve the plate bending problems with quadrilateral elements. The problems solved are:

(1) deflections and stresses in a circular plate with all edges simply supported under uniform load.

(2) deflections and stresses in a circular plate with all edges clamped under uniform load.

each case including four different …

Laminar Flow In A Porous Pipe With One Plugged End, Pyne-Hwa Ku

Theses

A steady laminar flow through a co-cylinder porous pipe with one plugged end was investigated theoretically to obtain velocity, pressure and shear stress distributions.

An integral momentum equation and the Darcy's law for flow through the porous wall were solved numerically by the Runge-kutta method.

As the fluid is injected from the outer wall into the porous tube, the fluid in the inner tube is accelerated from rest at the plugged end to a fully-developed velocity profile at the exit of the porous tube. It was found that the coefficient of the wall shear stress and the dimensionless pressure drop …

Stress Analysis Of A Pressure Vessel By The Finite Element Method, Hsin-Te Liao

Theses

The objective of this paper is to take a finite element program, called ANSYS, to analyze the surface stress distribution of a thin-wall pressure vessel with a spherical head.

The computer program ANSYS, which primarily applies the principle of virtual work in solid continuum, has been used to solve shell problems with quadrilateral element. Problems solved are: <1> hoop stress <2> meridional stress (<)3) maximum shear stress.

In this paper, the theoretical finite element formulation of axisymmetric elasticity of the ANSYS program is presented.

Finally, some numerical examples of shells with spherical heads of various radius are given. The solution obtained from ANSYS is very …

Discontinuity Stresses Analysis In Pressure Vessel, Jan-Joo Liu

Theses

In this paper, the ANSYS general purpose finite element computer aided design program was used to perform a series of stress analyses for shells with heads of various shapes.

The analysis included maximum discontinuity stresses, stress contours and displacements induced in axisymmetrical shells subjected to internal pressure loading; especially at the junction of the cylinder and heads of various shapes.

CONICAL SHELL finite elements and TWO-DIMENSIONAL ISOPARAMETRIC finite elements were used in the analysis. The results of the analyses compared very favorably with solutions derived from membrane and bending theory solutions for pressure vessels.

The effect of longitudinal and hoop …

Implementation Of Finite Element Method On A Microcomputer, Chi-Yuang Huang

Theses

A finite-element program FEM2D has been implemented on a PHILIPS microcomputer. The program has a generation preprocessor and thus makes finite-element analysis on a microcomputer considerably easier than before, since it allows models to be created and edited much faster than by manual method. The interactive program FEM2D prompts the user to input data directly from the screen. It is convenient for the user, both in teaching and learning.

The FEM2D is a two-dimensional finite-element program capable of solving two-dimensional problems, such as plane elasticity, heat transfer and imcompressible fluid flow problems. It is developed with a formulation of a …

An Analysis Of Different Desalination Processes, Vahe Garabed Hovsepian

Theses

The object of this thesis is to study the various modes of desalination and analyze the energy and economic requirements. The desalination methods discussed are, single stage desalination, Long tube vertical Evaporator, Multistage Flash distillation, Solar Energy method, Freezing method, Reverse osmosis & Electrodialysis.

It was found that for vapor reheat process at 350°F input 639 ft-lbs/lb product required 2.01 kw-hr/100gal. product and the total cost 51.6c/1000gal.

Not one process is best for everyone. In countries close to the equator, the solar energy method is the best. Most other countries depend on flash distillation process, etc. So we can't draw …

Substructuring Analysis For Impact Dynamics Using Ansys Finite Element Package, Chang Ho Cho

Theses

This thesis is intended to serve as an introductory guide to ANSYS finite element package for the analysis of impact dynamics. Substructuring technique has been used to reduce the degrees of freedom.

Finite element method is essentially a numerical technique to calculate elastic deformations. However, by introducing some techniques like gap element, the technique can be easily extended to rigid body dynamic analysis. To solve the equation of motion both for rigid body and elastic deformations, direct integration technique is used in this thesis, i.e., Houbolt method.

ANSYS is a large scale general purpose computer program for finite element analysis. …

Circular Plate Analysis Using Finite Element Method, Shyh-Rong Chiu

Theses

The ANSYS computer program is the application of finite element methods to large-scale engineering problems. In this work the ANSYS program has been employed to solve the circular plate under uniformly loaded with various boundary conditions as follows: (1) clamped along entire edge, (2) simply supported along entire edge, (3) clamped at several points along the boundary, (4) simply supported at several points along the boundary, and (5) simply supported 36 points with 4 points clamped..

The results obtained from the ANSYS program illustrated that the finite element method has no boundary conditions constraints and presents good approximations to the …

A Closed Form Image Force Function For Deposition Of Particles In A Cylindrical Tube, Hsi-Chung Chiou

Theses

This study investigated the behavior of charged particles suspended in a laminar steady incompressible flow in a cylindrical tube under the influences of image , inertia , viscous and gravitational forces. A new expression for the image force was obtained by introducing an approximate potential energy function. The velocity profiles employed in the analysis were uniform and parabolic.

The governing equations derived were based on Newton's second law of motion and were solved by a Runge-Kutta numerical method. The results were obtained for different values of Q, a dimensionless inertia-charge parameter. For a value of Q equal to zero the …

On Torsional Spring Constants At The Juncture Of Piping-Nozzle, Shean-Juinn Chiou

Theses

Numerical results of torsional spring constants at the juncture of piping-nozzle are studied in this thesis by using the "ANSYS" program and run on VAX computer. These results are presented in tabulated form for a piping-nozzle vessel with constant thickness of 0.375 in. Plot for the torsional spring constants in terms of beta (nozzle radius/pipe radius), gamma (pipe radius/thickness) and alpha (pipe length/radius) are also presented in this thesis. These data are under zero piping internal pressure with beta ranging from 0.1 to 0.8, and gamma ranging from 10 to 150. A numerical example with verification is also given.

The Stress Distribution Of The Frp Pressure Vessel By Using Ansys Program, Lung-John Tsai

Theses

The objective of this paper is to take advantage of a general purpose finite element computer program, called ANSYS, to analyze the surface stress distribution of a fiber reinforced plastic (FRP) laminated composite pressure vessel. The vessel is subjected to internal pressure, which is assumed to be constant over the interior surfaces.

In this paper, the material is assumed to be orthotropic, and the stress-strain relationship linear.

A FRP pressure vessel subjected to an Internal pressure, 6.895 MPa (1000 psi), is taken as an example. The results show that this approach compares well with a theoretical solution.

Chebyshev Approximate Solution For Stiff Problems, Kwo-En Hoh

Theses

Chebyshev polynomial and collocation methods are adapted to solve general ordinary differential equations ( initial-value problems and boundary-value problems ). Approximate solutions of initial-value problems are obtained in step-by-step fasion. the solutions have minimax absolute error in the interval and correct values at the end points. The approximate solutions of boundary-value problem will be continuous on the whole domain and have piecewise Chebyshev approximation characteristics in each subinterval of the chosen partition.

Computational Method For Robot Manipulator Dynamics Based On The Gibbs-Appell Equations, Kwang Bok Kim

Theses

Industrial robots are open-loop multi-degree of freedom mechanisms whose dynamic characteristics are described by nonlinear differential equations. The computations of forces and torques required at each joint of robot manipulator are crucial step for real time control of robot manipulators.

Vukobratovic developed a new computational method for rigid body articulated open-loop mechanisms based on the Gibbs -Appell equations to generate differential equations of motion for spatial open - chain mechanisms. To solve these equations, he introduced the recursive kinematic transformation matrices that represent the motion of each linkage with respect to the base linkage.

Computer programs are developed in this …

Pressure Drop In A Strainer Element By The Finite Element Method, Wei-Long Chen

Theses

The pressure drop in a strainer element which consists of a channel and a diffuser has been investigated by the finite element method and the semi-empirical analysis.

An existing finite element program, FEM2D using the penalty parameter model, was employed. It was found that the range of Reynolds numbers in the strainer element was 0.193 to 4.824. For the pressure drop in the channel, the finite element method is in agreement with the analytical solution. For flow in the diffuser, the finite element method failed to give satisfactory results due to flow separation.

Test 1596: Kubota M6030dt And M6030 Diesel 16-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1595: Kubota M5030dt And M5030 Diesel 16-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …