Engineering Commons^™

Nebraska Summary: S045 Massey Ferguson 3630, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S044 Case-Ih 9180, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S037-S038 Massey Ferguson 399, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Effect Of Material Parameters On The Initiation And Growth Of Adiabatic Shear Bands, R. C. Batra

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The thermomechanical problem involving simple shearing of a finite slab made of an isotropic and viscoplastic material is studied with the objective of finding the effect of the strain hardening parameter, strain-rate hardening parameters, thermal softening coefficient and thermal conductivity on the initiation and growth of adiabatic shear bands. The body is placed in a hard loading device, i.e., the velocity is prescribed at its top and bottom surfaces. A shear band is presumed to have formed if the addition of a perturbation in the temperature at the onset of plastic flow results in a localization of the shear strain. …

Energy Transmission Into The Human Hand From Vibrating Tools, Douglas D. Reynolds

Mechanical Engineering Faculty Research

A method for calculating power transmitted to the hands of operators who use vibrating hand tools is presented. Results that relate to a comprehensive multidiscipline NIOSH field study of several hundred chipper and grinder workers who used pneumatic hand tools are discussed. These results indicated that the total power in the frequency range of 6.3 to 1000 Hz transmitted to the hand ranged from 1080 to 7230 J/s for the chisel and from 0.852 to 157 J/s the handle of chipping hammers. For pneumatic grinders the power transmitted to the hands of the tool operators was in the range of …

Coupled Bending-Torsion Steady-State Response Of Pretwisted, Nonuniform Rotating Beams Using A Transfer-Matrix Method, Carl E. Gray Jr.

Mechanical & Aerospace Engineering Theses & Dissertations

Using the Newtonian method, the equations of motion are developed for the coupled bending-torsion steady-state response of beams rotating at constant angular velocity in a fixed plane. The resulting equations are valid to first order strain-displacement relationships for a long beam with all other nonlinear terms retained. In addition, the equations are valid for beams with the mass centroidal axis offset (eccentric) from the elastic axis, nonuniform mass and section properties, and variable twist. The solution of these coupled, nonlinear, nonhomogeneous, differential equations is obtained by modifying a Hunter linear second-order transfer-matrix solution procedure to solve the nonlinear differential equations …

A Transient Electromagnetic Flowmeter, Paul J. Lefebvre, William W. Durgin

Office of the Provost Scholarship

An electromagnetic flowmeter was developed to measure transient flows with a frequency response of 60 Hz. The approach taken was to develop suitable electronics to replace the electronics of a commercially available electromagnetic flowmeter normally used for steady-state operation. Use of the commercially available flowmeter body, which includes the magnetic coils, core, and signal electrodes, provided a relatively economical means of fabricating the transient flowmeter. A transient flow calibration facility consisting of a free-falling water column was also designed and built. Results of the calibrations are presented and show that the flowmeter can accurately measure transient flows up to the …

Radiant Energy Transfer And Radiant Barrier Systems In Buildings, Florida Solar Energy Center, Philip W. Fairey

FSEC Energy Research Center®

In Florida and other southern climates we depend on a number of strategies to keep heat out of buildings. Mostly, these affect heat gains by conduction or convection. In the average house, insulating walls and ceilings primarily restricts conduction. Double-glazed windows restrict both conductive and convective heat gain. We have largely ignored radiation - the third means of heat transfer - except in using window treatments and coatings that reflect, absorb or shade from solar energy. But research points to exciting potential for reducing heat gain in buildings by controlling radiation transfer in walls and ceilings through the use of …

Techniques For Shading Residential Walls And Windows, Florida Solar Energy Center, Philip W. Fairey

FSEC Energy Research Center®

Solar radiation is a major heat source in buildings - welcome in cold weather but a summertime problem. Florida's long cooling season and short heating season increase the importance of protecting windows, walls and sliding glass doors during hot weather, while still permitting solar heat to enter a building during cold weather. cooling and heating energy savings of 10% - 20% are possible through good shading strategies. Properly designed roof overhangs can provide adequate sun protection, especially for south-facing surfaces. Vertical shading devices such as trees, trellises, trellised vines, shutters, shading screens awnings and exterior roll blinds are also effective. …

Solar Water Heater Troubleshooting Checklist, Florida Solar Energy Center

FSEC Energy Research Center®

Lists the Symptom, Component, Possible Cause, and Remedy/Check of possible solar hot water heater problems.

Solar Ovens And Cookers, Florida Solar Energy Center

FSEC Energy Research Center®

Solar ovens work much like solar collectors used in domestic water heating systems. Both collect solar radiation, convert it to heat and transfer it to another substance. Solar ovens, however, focus the sun's rays with reflective surfaces on one point. The object of the sun's energy in the solar oven is the food.

Recipes For Solar Cooking, Florida Solar Energy Center, Jo Townsend

FSEC Energy Research Center®

As energy extension agent for the University of Florida Extension Service, Jo Townsend serves as the energy educator to small businesses in central Florida. She conducts employee programs on energy conservation in the workplace. She received her B.S. in home economics from Florida State University and her M.E. from the University of Central Florida. Formerly a home economist for the Florida cooperative Extension Service, Townsend researched and tested recipes for use in microwaves when they first gained popularity. She has been a consultant to Southern Living magazine and to Florida's seafood industry. For the last year, she has tested recipes …

Electric Power Transmission & Purchases : Report Of A Study By The Joint Standing Committee On Utilities, 112th Maine Legislature, Maine. Legislature. Joint Standing Committee On Utilities

Maine Collection

Electric Power Transmission & Purchases : Report Of a Study By the Joint Standing Committee on Utilities, 112th Maine Legislature

Maine Legislature. Joint Standing Committee on Utilities.

Augusta, Maine (December 2, 1986).

Contents: Introduction / Issues & Recommendations / Review of 1986 Legislation / Maine's Electric Power Picture / Technical Analysis of Transmission & Wheeling / Economic Implications of Transmission & Wheeling /. Legals Analysis of Transmission & Wheeling / Proposed Legislation / Appendices / Tables & Figures

Shear Layer Coupling With Side-Branch Resonators, D. D. Erickson, William W. Durgin, C. F. Maguire Iii, M. J. Moeller

Office of the Provost Scholarship

High velocity flow past the junction of a side branch with a pipe can result in the excitation of depth-mode standing waves in the branch. The shear layer separating the main stream flow and the cavity provides coupling between the driving and the driven flow. Photographic evidence indicates that large scale vortex structures develop at the shear layer. The vortex formation process involves strongly non-linear instability of the shear layer and may be characterized as a non-linear fluid mechanical oscillator. The standing wave system formed in the cavity is essentially an acoustic wave system of nearly linear character. The principle …

Cooling With Ventilation, Florida Solar Energy Center, Subrato Chandra

FSEC Energy Research Center®

In keeping with the national energy policy goal of fostering an adequate supply of energy at a reasonable cost, the United States Department of Energy (DOE) supports a variety of programs to promote a balanced and mixed energy resource system. The mission of the DOE Solar Building Research and Development Program is to support this goal by providing for the development of solar technology alternatives for the buildings sector. It is the goal of the Program to establish a proven technology base to allow industry to develop solar products and designs for buildings that are economically competitive and can contribute …

Test 1606: John Deere 2955 Diesel 16 And 8-Speed (Tss Transmission), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1605: John Deere 2755 Diesel 16-Speed Also 8-Speed (Tss Transmission), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1604: Case International 685 Diesel (Chassis S/N B51023b018001-And Higher) Also Case International 695 And 4210 Diesel 8 And 16-Speeds, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1603: Hesston 160-90 Turbo Powershift Fiat Diesel 16-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Calibration Of Old Dominion University Low-Speed Wind Tunnel, Nicolaos P. Sargianos

Mechanical & Aerospace Engineering Theses & Dissertations

No Abstract.

Chemoviscosity Modeling Of Thermosetting Resins, Jia-Mo Bai

Mechanical & Aerospace Engineering Theses & Dissertations

A new analytical model for simulating chemoviscosity of thermosetting resin has been formulated. The model is developed by modifying the well-established Williams-Landel-Ferry (WLF) theory in polymer rheology for thermoplastic materials. By introducing a relationship between the glass transition temperature Tg (t) and the degree of cure a(t) of the resin system under cure, the WLF theory can be modified to account for the factor of reaction time. Temperature-dependent functions of the modified WLF theory constants C₁(T) and C₂(T) were determined from the isothermal cure data. Theoretical predictions of the model for the resin under dynamic …

Test 1601: Zetor 6245, 6211, 4320 And 4340 Diesel 10-Speeds, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1602: Zetor 7745, 7711, 6320 And 6340 Diesel 10-Speeds, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Effect Of Center Of Gravity Location On Optimum Performance Of Random Vibratory Vehicle Suspension, Daniel Mahar

Theses

This study provides the analysis for the optimal design of a conventional vehicle suspension system, consisting of a sprung mass (vehicle body) and two unsprung masses (wheel frame), accentuated by the implementation of a damped absorber to the unsprung masses. Further, the effect of the c.g. (center of gravity) location of the vehicle body is investigated. A two dimensional, four degrees of freedom linear model is chosen. Randomly profiled terrain is assumed to impart hyperbolically distributed stationary vertical random displacements to the front and rear wheels. For generalization, nondimensional design parameters are selected. Criteria for optimization include the tire-terrain normal …

A Method For Determining What Effect Cad Has On Productivity In Gage Design Of The Process And Tool Department At The John Deere Component Works, Dan Rae Teel

Graduate Research Papers

The purpose of this study was to develop a method for determining what effect CAD has on productivity in the Gage Design area of the Process and Tool Department of the John Deere Component Works.

The Mechanics Of Flycasting: The Flyline, Graig A. Spolek

Mechanical and Materials Engineering Faculty Publications and Presentations

In order to propel a fishing fly through the air toward the distant quarry, a rather massive line, to which the fly is attached, is cast. As the cast line rolls out, the fly actually accelerates horizontally and seems to defy physical law. The phenomenon is modeled simplistically to determine the magnitude of this effect. In the absence of air drag, the fly can accelerate to increase its velocity by an order of magnitude. Air friction dramatically decreases the effect, but some fly accelerationis still predicted. By tapering the flyline in various ways, the fly velocity history can be significantly …

Analyze3d, A Structural Analysis Program Employing Membrane And Solid Finite Elements, James Mendham Gathercole

Theses

The purpose of this thesis is to describe the addition of an 8 and 20-node isoparametric brick element to the finite element program ANALYZE, permitting three-dimensional analysis. The reason for the addition is that even though Analyze is a relatively simple program, its simplicity makes it a good educational tool for finite element courses. The added brick element expands the use of the program for educational purposes.

In its original form, Analyze is a finite element package for static structural analysis developed at Wright Patterson Air Force Base. The program consists of four finite elements: (1) bar, (2) membrane triangle, …

A Tracheoesophageal Puncture Voice Prosthesis, Georghios Makris

Theses

A voice prosthesis was developed that allows verbal communication of laryngectomised patients. The prosthesis requires a superiorly directed tracheoesophageal puncture in which the periscope mounted on the tracheal stoma vent is introduced. The prosthesis is operated by air injection through the periscope. Air injection is achieved by pulmonary pressure after the occlusion of the stoma vent. Stoma vent occlusion can be achieved either by the patient's finger or by the designed cover valve mounted on the prosthesis. The cover valve allows free breathing, hand-free prosthesis use, and it can release excess pressure during coughing. Periscope valve air resistance tests have …

Theoretical Investigation Of Submerged Turbulent Jet, Talal N. Hindi

Theses

A theoretical investigation concerning the flow characteristics velocity distribution of a circular submerged turbulent axisymetricic water jet impinging on a flat plate was carried out. Starting with the use of the available data and equations obtained by previous investigators and found room for improvement. By solving these equations for the velocity distribution and comparing them to the experimental results is was found out where improvements of the analysis were were necessary. Then taking Tollwien's solution for the velocity distribution and changing the reference axis to see whether or not the equations would give better results for velocity calculations. With certain …

Interpretation Of Venous Occlusion Plethysmography Using A Nonlinear Model, F. A. Anderson, Jr., William W. Durgin, H. Brownell Wheeler

Office of the Provost Scholarship

Venous occlusion plethysmography (VOP) is a noninvasive technique widely employed for the detection of deep-vein thrombosis. Previous reports that VOP outflow curves are closely fit by a first-order exponential suggest that venous compliance and resistance are nearly constant. Typically, however, the venous compliance function has a sigmoid shape; in addition, the resistance in a collapsing tube must increase. This paradox was resolved by the surprising finding that for realistic nonlinear compliance and resistance these nonlinearities cancel, producing a quasilinear venous outflow that approximates a simple exponential.