Engineering Commons^™

Compliant Pliers, Ashok Midha, S. C. Visser

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The pliers include an endless loop, a top jaw appended to the endless loop, and a bottom jaw appended to the endless loop. The endless loop includes in series a top grip handle, a spring segment, a bottom grip handle and a compliant strip interconnecting the top and bottom grip handles. A rolling surface on the top grip handle rolls on a contact portion of the bottom grip handle. The rolling action causes the compliant strip to flex which causes the top and bottom jaws to move toward one another. The endless loop provides a built-in automatic spring and enhances …

Application Of Reanalysis Techniques For Pattern Design Of Spot Welds, Young San Kim

Mechanical & Aerospace Engineering Theses & Dissertations

Extensive benchmarking on competitive cars has shown that the durability of vehicles, assembly-induced variations, and assembly cost are directly related to the quality and number of spot welds. On most luxury cars, approximately 4,500 to 5,000 spot welds are found. On less expensive cars, the range is from 3,500 to 4,500. These cars usually inherit more noise, rattles, squeaks, and other quality-related problems. These problems have motivated the search for a new capability to systematically place welds in the most critical areas, with a minimum number of welds for car bodies, while satisfying all performance requirements (e.g., stiffness, stress distribution, …

Numerical Simulation Of Complex, Three-Dimensional, Turbulent-Free Jets, Robert V. Wilson

Mechanical & Aerospace Engineering Theses & Dissertations

Three-dimensional, incompressible turbulent jets with rectangular and elliptical cross-section are simulated with a finite-difference numerical method. The full Navier-Stokes equations are solved at low Reynoids numbers, whereas at high Reynolds numbers filtered forms of the equations are solved along with a sub-grid scale model to approximate the effects of the unresolved scales. A 2-N storage, third-order Runge-Kutta scheme is used for temporal discretization and a fourth-order compact scheme is used for spatial discretization. Although such methods are widely used in the simulation of compressible flows, the lack of an evolution equation for pressure or density presents particular difficulty in incompressible …

Gas And Liquid Phase Transport In Pulsed Fuel Sprays, Pete D. Jennings, James A. Drallmeier

Mechanical and Aerospace Engineering Faculty Research & Creative Works

An infrared extinction technique was used to characterize spatially and temporally the vapor phase of a transient fuel spray. Optical extinction data were taken at two laser wavelengths and compared to obtain fuel vapor partial pressure values averaged over the line-of-sight through the spray. A transient fuel injector spray was characterized at several axial positions with a spatial resolution of 0.125 cm and a temporal resolution of 0.2 ms. With the knowledge of an axisymmetric spray pulse, the line-of-sight averaged results were deconvoluted to obtain spatially resolved vapor pressure data. The same spray was also characterized using phase/doppler interferometry to …

A Class Of Modified Hopfield Networks For Aircraft Identification And Control, Jie Shen, S. N. Balakrishnan

Mechanical and Aerospace Engineering Faculty Research & Creative Works

This paper presents a class of modified Hopfield neural networks and their use in solving aircraft optimal control and identification problems. This class of networks consists of parallel recurrent networks which have variable dimensions that can be changed to fit the problems under consideration. It has a structure to implement an inverse transformation that is essential for embedding optimal control gain sequences. Equilibrium solutions are discussed. Energy minimization of the networks leads to identification of the system parameters. Numerical results are provided to identify the dynamics of an aircraft, and the corresponding optimal control is calculated online. Comparison of the …

Effect Of Inflow Pressure And Wall Heat Transfer On Shock-Induced Combustion/Detonation, B. S. Green, Harlan F. Nelson

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Oblique detonation waves are possible ignition mechanisms for scramjet engines. Results from a numerical study of the effects of changing the inflow pressure on oblique detonation wave structure for supersonic flow of a stoichiometric hydrogen-air mixture over a flat plate followed by a ramp are presented. Viscous effects and finite-rate chemistry are considered. Inflow pressure is varied from 0.1 to 1 atmosphere for Mach 4 inflow over a 30-degree ramp. Also, the effect of wall heat transfer rate is examined by comparing adiabatic wall, and constant temperature wall solutions. A separation bubble forms at the intersection of the flat plate …

A Finite Element Model Of Thermoacoustic Oscillations In Rayleigh Flow, Carlos A. Gutierrez, Walter Eversman

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The work reported here describes a portion of the development of a finite element model of thermoacoustic oscillations in ducted flows, including three dimensional geometries and nonuniform mean flows with steady heat addition. The thermoacoustic problem is not modeled by a form of the convected wave equation but instead by the conservation equations in primitive form. In this paper the three-dimensional model is reduced to one dimension, applicable to a uniform geometry, but allowing an axially nonuniform flow with sharp gradients in temperature, density, and Mach number. The steady mean flow is computed as a Rayleigh flow. Calculations are shown …

Target Profile Estimation Using Haar Functions, William R. Bockman, S. N. Balakrishnan, Christopher D'Souza, James Cloutier

Mechanical and Aerospace Engineering Faculty Research & Creative Works

An approach to estimating the target acceleration in a maneuvering target model using Haar function partial summations to model the target acceleration is developed. A kinematic constraint is applied to the maneuvering target model and the effects of the use of this constraint are reviewed.

Radiative Heating In Scramjet Combustors, Harlan F. Nelson

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Currently, there is considerable interest in scramjet engines for hypersonic aircraft and missiles. This paper presents preliminary calculations of the radiative heating of the walls of scramjet combustion chambers. The analysis assumes isothermal, constant property flow fields which are representative of actual combustor flow fields. The fuel is H2 and N2 is taken as inert. Temperature in the combustor is on the order of 2000 to 3000 K and pressure is of the order of 5 atm. The combustion products consist mainly of H2O and OH. These gases are strong radiators in the infrared. Radiation heating can be significant because …

Global Characteristics And Structure Of Hydrogen-Air Counterflow Diffusion Flames, J. Zhao, Kakkattukuzhy M. Isaac, G. L. Pellett

Mechanical and Aerospace Engineering Faculty Research & Creative Works

A model based on similarity transformation, for the nitrogen-diluted, H2-air opposed-jet laminar counterflow diffusion flame (CFDF), was developed independently of earlier models, and numerically solved to study flame location and flame structure and extinction limits. Numerical stiffness is handled by a special treatment of the species production term. Flame location with respect to the stagnation plane is identified as an important parameter that governs H2-air diffusion flames, and physical explanations are given to show how flame location is affected by fuel dilution, strain rate, and Lewis number. Results show very good agreement with experimental extinction conditions. The effect of thermal …

Test 1649/1: Buhler Versatile 2145 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 1648/1: Buhler Versatile 2160 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 1646/1: Buhler Versatile 2210 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 1618: Valmet 8150 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 1633: Valmet 8550 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 941: John Deere 3020 Syncro-Range Gas, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 1709: Case Ih 7220 Diesel 18-Speed (Chassis S/N Jja0065000 And Higher) Also Case Ih 8920 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE

General

Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure.

The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1714: Case Ih 9380 Diesel 12-Speed (Chassis S/N Jee0036501 And Higher), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

System Identification Methods For Dynamic Testing Of Fluid-Film Bearings, Jerzy T. Sawicki, M. L. Adams, R. J. Capaldi

Mechanical Engineering Faculty Publications

There are various system identification approaches typically used to extract the rotordynamic coefficients from simultaneously measured dynamic force and motion signals. Since the coefficient values extracted can vary significantly as a function of the system identification approach used, more attention is needed to treat this issue than is typically included in the rotor dynamics literature. This paper describes system identification and data reduction methods used for extracting rotordynamic coefficients of fluid-film journal bearings. Data is used from a test apparatus incorporating a double-spoolshaft spindle which permits independent control over the journal spin speed and the frequency of an adjustable-magnitude circular …

Nebraska Summary: S218 New Holland 8670, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 1711: Case Ih 7240 Diesel 18-Speed (Chassis S/N Jja 0065000 And Higher), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE

General

Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure.

The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1710: Case Ih 7230 Diesel 18-Speed (Chassis S/N Jja0065000 And Higher), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE

General

Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure.

The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Plastic Fiber Rolling For Concrete Reinforcement, Jeffery S. Thomas

Masters Theses

"Fiber reinforced concrete is gaining in acceptance and usage as its strength and toughness benefits are realized. Polypropylene fibers are currently the most commonly used fibers. However, the cost of virgin plastics limits the percent content that can be economically added to concrete. One would first believe that recycled plastics could offer a viable alternative to virgin-plastic fibers, but at present time extra selection and cleaning steps required to reprocess the recycled plastic into fibers makes it more expensive than virgin-plastic fibers. A fiber rolling process conceived and developed at the University of Missouri-Rolla has the potential of making recycled …

Hamiltonian Based Adaptive Critics For Missile Guidance, S. N. Balakrishnan, Jie Shen

Mechanical and Aerospace Engineering Faculty Research & Creative Works

A Hamiltonian based adaptive critic structure is proposed for solving missile guidance problems. This structure consists of a supervisor neural network called 'critic' and a controller network called 'action'. Together they are used to solve model-based guidance problems. The advantage of this approach is that: i) the training data for each network is created by the other network, ii) the converged solutions yield near optimal guidance over the entire span of the training range, and iii) they can be used as feedback controllers though trained off-line. A main contribution is that we establish a direct link between traditional optimal control …

Non-Axisymmetric Matrix Cracking And Interface Debonding With Friction In Ceramic Composites, F. S. Ji, Lokeswarappa R. Dharani

Mechanical and Aerospace Engineering Faculty Research & Creative Works

An three-dimensional analytical model based on the principle of minimum potential energy is developed and applied to determine the stress state in a discrete fiber/matrix composite cylinder subjected to axial tensile loading in the fiber direction and containing a non-symmetric transverse matrix crack and an interface debond. The friction over the debonded interface is incorporated into the analysis. The strain energy release rates associated with the matrix crack and the interface debonding under the combination of the applied load and the interface frictional force are computed. The strain energy release rate criterion has been employed to evaluate the critical applied …

An Interdisciplinary Solar Energy Project, William J. Hutzel

School of Engineering Technology Faculty Publications

An HVAC course, previously offered to students in Mechanical Engineering Technology (MET), has been re-structured to include students in Building Construction Management (BCM). A large project is always an integral part of this course, creating a unique opportunity for collaboration between two distinctly different groups of Technology students. This cooperation is particularly beneficial because MET and BCM graduates frequently cross paths during their professional careers. Many MET graduates operate and service heating, ventilating, and air conditioning equipment that was originally specified and installed by BCM graduates. This paper discusses and evaluates student interactions during a solar …

On The Effectiveness Of Dry Film Lubricant Coatings In Reducing Automotive Valve Train Wear, Evan Benstead, Martin L. Smith, Joseph Foyos, Omar S. Es-Said

Mechanical Engineering Faculty Works

The effect of three dry lubricants on automotive valve train wear resistance was studied experimentally. Scuffing wear occurs as the cam slides across the lifter face where the rotating motion of the camshaft is converted into the linear motion necessary to drive the cylinder head valves. This scuffing is caused by localized microscopic bonding between the skidding surfaces. It can be minimized by using dry film lubricant coatings to increase the boundary lubrication depth adjacent to the contact area. To compare valve train wear resistance in the laboratory, rotating cam lobes coated with dry lubricants--parkerization, spray-applied graphite coating, and brush-applied …

An Investigation Of Diameter Measurement Repeatability Using A Coordinate Measuring Machine And A Multi-Baseline Repeatability Assessment Methodology, Bruce Marsh

Dissertations and Theses @ UNI

The need for reliable and consistent measurement has become more acute with the use of statistical process control (SPC), gage repeatability and reproducibility (Gage R&R) assessment, and high precision, computer-controlled gaging systems. Although it is often overlooked, the inspection methodology under which various features are inspected has an impact on Gage R&R results. This notion was confirmed when a 1993 thesis study substantiated inspection methodology as a source of measurement variability in direct computer-controlled, coordinate measuring machines (DCC/CMMs). Although this study explored a methodology to bring measurement variability under statistical control, the tested assessment methodology--single baseline repeatability assessment--was not validated. …

Experiments In The Coordinated Control Of An Underwater Arm/Vehicle System, Timothy W. Mclain, Stephen M. Rock, Michael J. Lee

Faculty Publications

The addition of manipulators to small autonomous underwater vehicles (AUVs) can pose significant control challenges due to hydrodynamic interactions between the arm and the vehicle. Experiments conducted at the monterey Bay Aquarium Research Institute (MBARI) using the OTTER vehicle have shown that dynamical interactions between an arm and a vehicle can be very significant. For the experiments reported in this paper, a single-link "arm" was mounted on OTTER. Tests showed that for 90-degree, two-second repetitive slews of the arm, the vehicle would move as much as 18 degrees in roll and 14 degrees in yaw when no vehicle control was …

A Dual Neural Network Architecture For Linear And Nonlinear Control Of Inverted Pendulum On A Cart, S. N. Balakrishnan, Victor Biega

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The use of a self-contained dual neural network architecture for the solution of nonlinear optimal control problems is investigated in this study. The network structure solves the dynamic programming equations in stages and at the convergence, one network provides the optimal control and the second network provides a fault tolerance to the control system. We detail the steps in design and solve a linearized and a nonlinear, unstable, four-dimensional inverted pendulum on a cart problem. Numerical results are presented and compared with linearized optimal control. Unlike the previously published neural network solutions, this methodology does not need any external training, …