Engineering Commons^™

Development And Application Of A New Modeling Technique For Production Control Schemes In Manufacturing Systems, Bashar Hafez Sader

Theses and Dissertations

This dissertation presents dynamic system models of continuous manufacturing systems based on analogies with electrical systems. The developed modeling technique has the capability to explicitly specify production control schemes including control points, material and information flow paths, and logical operations. The model provides standard graphical representations and governing equations to describe both the steady state and transient responses of continuous manufacturing systems. For deterministic systems, these equations can be solved to get closed-form solutions. For stochastic systems, numerical solutions can be obtained for any probabilistic distribution. The electrical analogs provide an excellent tool to model control signals and logical operations. …

Determination Of Dynamic Delamination Toughness Of A Graphite-Fiber/Epoxy Composite Using Hopkinson Pressure Bar, Xiangfa Wu, Yuris A. Dzenis

Department of Engineering Mechanics: Faculty Publications

Modified dynamic three-point-bending and compact shearing test configurations based on Hopkinson pressure bar (HPB) and crack detection gage (CDG) (Vishay Intertechnology, Inc) were used for the determination of the dynamic mode I and mode II delamination-initiation toughness of a unidirectional graphite-fiber/epoxy composite made of P7051S-20Q-1000 prepregs (Toray Composites America). The transient loading history was recorded precisely by the HPB installed with a highresolution digital oscilloscope, and the crack initiation and delay time were captured using the CDG. By means of dynamic finite-element analysis (FEA) of the impact processes with the loading history and crack initiation time as input, the critical …

Development Of A Linear Control Model For A Camless Valvetrain, Domenic R. Albert

Electronic Dissertations and Theses

The disciplines of mechanical and electrical engineering have been merging slowly over the last few decades. More specifically, the automotive industry has reaped the benefits of using electronics to improve upon the economics and ergonomics of business well as product. Although electronic systems have proved to be useful throughout consumer vehicles, the engine is arguably the area that benefits the most. Essentially, efficiency and power output of an internal combustion engine can be improved by optimizing the airflow of the cylinders. Since this airflow is controlled by the valve train, their manipulation affects the overall performance of an engine. Additionally, …

Design And Development Of A Mems-Based Capacitive Bending Strain Sensor And A Biocompatible Housing For A Telemetric Strain Monitoring System., Julia Marie Weyer Aebersold 1969-

Electronic Theses and Dissertations

Lumbar arthrodesis or spinal fusion is usually performed to relieve back pain and regain functionality from ruptured discs, disc degenerative disease, trauma and scoliosis. Metal rods are often fixed to the spine with screws or hooks, while fusion develops on the affected vertebrae. Fusion is determined by visual examination of radiographic images (X-ray), computed tomography (CT) scans or magnetic resonance imaging (MRI), yet these inspection procedures are subjective methods of review. They do not objectively confirm the presence of spinal fusion, which can lead to exploratory surgery to determine if fusion has occurred. Therefore, a need has arisen to develop …

A Case Study On Implementation Of Quality Function Deployment Into The Design Process Of A Small Job Shop, Benjamin A. Thomson

All-Inclusive List of Electronic Theses and Dissertations

The majority of research involving Quality Function Deployment (QFD) was focused on large consumer based companies and not small job shop business-to-business companies. This case study involved the implementation of QFD into the design process at Reynolds & Co., a small job shop in Terre Haute, IN. The specific objectives of the research were to find the QFD concepts that apply to the improvement of Reynolds & Co.'s (small job shop) design process. The next objective was to reduce the average design time associated with Reynolds & Co.'s design process. The final objective of this case study was to reduce …

Nanocharacterization Of Bio-Silica Using Atomic Force And Ultrasonic Force Microscopy, Vinaypreet S. Gill, Kevin P. Hallinan, N. S. Brar

Mechanical and Aerospace Engineering Faculty Publications

Nanotechnology has become central to our research efforts to fabricate relatively smaller size devices, which are more versatile than their older and larger predecessors. Silica is a very important material in this regard. Recently, a new biomimetically inspired path to silica production has been demonstrated. This processing technique was inspired from biological organisms, such as marine diatoms, which produce silica at ambient conditions and almost neutral ph with beautiful control over location and structure. Recently, several researchers have demonstrated that positional control of silica formed could be achieved by application of an electric field to locate charged enzymes responsible for …

Extension Of Stereolithography Mold Life Using Gas-Assisted Injection Molding, Dilip Bose Ramalingam Nagarajan

Theses and Dissertations - UTB/UTPA

Stereolithography (SL) molds show great promise for injection molding of limited number of parts, greatly reducing the time to product and production cost. However, they present challenges to designers because of their strength, thermal characteristics and shorter lifetimes compared to metal molds. Gas-assisted injection molding (GAIM) has been used to alleviate the problems of distortion and thermal damage. The use of GAIM makes it possible to produce a large number of parts compared to conventional injection molding in epoxy molds with higher quality. In this research solid models of the mold with different part geometry were created using CAD and …

The Use Of Confidence Intervals For The Control Limits Of X¯ And S Control Charts, Daniel A. Lopez

Theses and Dissertations - UTB/UTPA

This research focuses on the variation observed on the control limits of X¯ and S control charts, due to the sampling schemes. In previous studies it has been shown that the estimated control limits derived by a small number of subgroups does not help in setting up reliable control limits. It has also been shown that estimating control limits from a large number of subgroups is not a feasible option. In this research quantile tables will be derived by sampling from the standard normal distribution and used to explain the effects of sampling on the control limits. The tables will …

Slip Behavior In Liquid Films On Surfaces Of Patterned Wettability: Comparison Between Continuum And Molecular Dynamics Simulations, Nikolai V. Priezjev, Anton A. Darhuber, Sandra M. Troian

Mechanical and Materials Engineering Faculty Publications

We investigate the behavior of the slip length in Newtonian liquids subject to planar shear bounded by substrates with mixed boundary conditions. The upper wall, consisting of a homogenous surface of finite or vanishing slip, moves at a constant speed parallel to a lower stationary wall, whose surface is patterned with an array of stripes representing alternating regions of no shear and finite or no slip. Velocity fields and effective slip lengths are computed both from molecular dynamics (MD) simulations and solution of the Stokes equation for flow configurations either parallel or perpendicular to the stripes. Excellent agreement between the …

Modeling, Fabrication, And Optimization Of Niobium Cavities: Phase Iii Fourth Quarterly Report, Robert A. Schill Jr., Mohamed Trabia, William Culbreth

Transmutation Sciences Materials (TRP)

Niobium cavities are important parts of the integrated NC/SC high-power linacs. Over the years, researchers in several countries have tested various cavity shapes. They concluded that elliptically shaped cells are the most appropriate shape for niobium superconducting cavities. The surface preparation can significantly affect the secondary electron emission yields. Such yields are used in design codes. Current codes use values obtained from niobium samples cleaned by a different means at temperatures other than the operating temperature. Secondary electron emission studies on LANL surface-cleaned niobium are conducted with preliminary data presented in this report at room temperature. Soon studies will be …

Induction Heating Of Thin Films, Paul L. Bergstrom, Melissa L. Trombley

Michigan Tech Patents

A method of performing regional heating of a system having a substrate. The method may include applying a thin film to the system, and controllably energizing a coil positioned near the thin film. The energized coils thereby generate a magnetic flux. The method further includes inducing a current in the thin film with the magnetic flux thereby heating the system.

Theoretical Evaluation Of The Nightcool Nocturnal Radiation Cooling Concept, Florida Solar Energy Center, Danny Parker

FSEC Energy Research Center®

An evaluation has been conducted of the potential of a night sky cooling system to substantially reduce space cooling needs in homes in North American climates. The report describes the innovative residential cooling system which uses nocturnal night sky radiation from a roof integrated radiator. The system uses a sealed attic covered by a highly conductive metal roof which is selectively linked by air flow to the main zone with the attic zone to provide cooling- largely during nighttime hours. Available house mass is used to store sensible cooling. Additional dehumidification is done during the evening hours as warranted by …

Ole Miss Engineer 2005

Ole Miss Engineer

No abstract provided.

Development Of A Novel Microreactor For Improved Chemical Reaction Conversion, Yu Liang

Doctoral Dissertations

Microreactors have been widely studied over the past two decades for different chemical reactions, to develop new analytical capabilities, and to obtain high mixing performance in the reactors. The main objectives of this work are to investigate the effect of different microchannel structures on the fluid properties and mixing behavior in microreactors, and to design, fabricate, and test a novel microreactor for higher conversion in a chemical reaction. The development of this novel microreactor is intended to provide a valuable guideline in achieving enhanced chemical mixing and to make available a solid research base for optimization of the yield of …

Nanomechanical Characterization Of Cavity Growth And Rupture In Hydrogen-Implanted Single-Crystal Batio3., Young-Bae Park, Patrick Nardi, Xiaodong Li, Harry A. Atwater

Faculty Publications

A thermodynamic model of cavitynucleation and growth in ion-implanted single-crystal BaTiO₃ layer is proposed, and cavity formation is related to the measured mechanical properties to better understand hydrogen implantation-induced layer transfer processes for ferroelectric thin films. The critical radius for cavitynucleation was determined experimentally from blistering experiments performed under isochronal anneal conditions and was calculated using continuum mechanical models for deformation and fracture, together with thermodynamic models. Based on thermodynamic modeling, we suggest that cavitiesgrow toward the cracking criteria at a critical blister size whereupon gas is emitted from ruptured cavities. The main driving force for layer splitting is …

The Coupling Effect Of Interfacial Adhesion And Tensile Residual Stress On A Thin Membrane Adhered To A Flat Punch, Kai Tak Wan, Lior Kogut

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Adhesion and residual stress play a critical role in the performance and reliability of microdevices, in particular, the cross bridge of RF microswitches. to investigate their combinatorial influences on thin films, an elastic model is constructed for a clamped circular membrane in contact with the planar surface of a rigid cylindrical punch. External force applied to the punch leads to thin film delamination and ultimately 'pull-off' at a critical non-zero contact radius. Characteristic trends of the mechanical responses were obtained for fixed load and fixed grips in terms of pull-off force, punch displacement and contact radius. It is shown that …

Biomechanical Measures Of Neuromuscular Control And Valgus Loading Of The Knee Predict Anterior Cruciate Ligament Injury Risk In Female Athletes, Timothy E. Hewett, Gregory D. Myer, Kevin R. Ford, Robert S. Heidt Jr., Angelo J. Colosimo, Scott G. Mclean, Antonie J. Van Den Bogert, Mark V. Paterno, Paul Succop

Mechanical Engineering Faculty Publications

Background: Female athletes participating in high-risk sports suffer anterior cruciate ligament injury at a 4- to 6-fold greater rate than do male athletes.

Hypothesis: Prescreened female athletes with subsequent anterior cruciate ligament injury will demonstrate decreased neuromuscular control and increased valgus joint loading, predicting anterior cruciate ligament injury risk.

Study Design: Cohort study; Level of evidence, 2.

Methods: There were 205 female athletes in the high-risk sports of soccer, basketball, and volleyball prospectively measured for neuromuscular control using 3-dimensional kinematics (joint angles) and joint loads using kinetics (joint moments) during a jump-landing task. Analysis of variance as well as linear …

Damage Assessment Of Aerospace Structural Components By Impedance Based Health Monitoring, Andrew L. Gyekenyesi, Richard E. Martin, Jerzy T. Sawicki, George Y. Baaklini

Mechanical Engineering Faculty Publications

This paper addresses recent efforts at the NASA Glenn Research Center at Lewis Field relating to the set-up and assessment of electro-mechanical (E/M) impedance based structural health monitoring. The overall aim is the application of the impedance based technique to aeronautic and space based structural components. As initial steps, a laboratory was created, software written, and experiments conducted on aluminum plates in undamaged and damaged states. A simulated crack, in the form of a narrow notch at various locations, was analyzed using piezoelectric-ceramic (PZT: lead, zirconate, titarate) patches as impedance measuring transducers. Descriptions of the impedance quantifying hardware and software …

Damage Assessment Of Aerospace Structural Components By Impedance Based Health Monitoring, Andrew L. Gyekenyesi, Richard Martin, Jerzy T. Sawicki, George Y. Baaklini

Mechanical Engineering Faculty Publications

This paper addresses recent efforts at the NASA Glenn Research Center at Lewis Field relating to the set-up and assessment of electro-mechanical (E/M) impedance based structural health monitoring. The overall aim is the application of the impedance based technique to aeronautic and space based structural components. As initial steps, a laboratory was created, software written, and experiments conducted on aluminum plates in undamaged and damaged states. A simulated crack, in the form of a narrow notch at various locations, was analyzed using piezoelectric-ceramic (PZT: lead, zirconate, titarate) patches as impedance measuring transducers. Descriptions of the impedance quantifying hardware and software …

3d Modelling With Linear Approaches Using Geometric Primitives, Mochammad Zuliansyah

Makara Journal of Technology

In this paper, we study linear approaches for 3D model acquisition from non-calibrated images. First, the intrinsic and extrinsic camera calibration is taken into consideration. In particular, we study the use of a specific calibration primitive: the parallelepiped. Parallelepipeds are frequently present in man-made environments and naturally encode the affine structure of the scene. Any information about their euclidean structure (angles or ratios of edge lengths), possibly combined with information about camera parameters is useful to obtain the euclidean reconstruction. We propose an elegant formalism to incorporate such information, in which camera parameters are dual to parallelepiped parameters, i.e. any …

2005 (Spring) Ensi Informer Magazine, Morehead State University. Engineering Sciences Department

ENSI Informer Magazine Archive

The ENSI Informer Magazine published in the spring of 2005.

Experimental Determination Of Convection Boiling Curves For Water And Ethylene Glycol In A Rectangular Channel With Localized Heating, Andrew T. O'Neill

Masters Theses

Convective boiling experiments were conducted to show the effects of velocity, pressure, and subcooling on both water and a water-ethylene glycol mixture. Boiling curves were obtained in a 30 mm wide by 20 mm high rectangular channel with an upward facing 20 mm wide by 30 mm long rectangular copper heater. The velocity ranged from 0.5 m/s to 4.0 m/s, the pressure ranged from 1.0 atm to 2.6 atm, and the subcooling ranged from 10°C to 50°C. The curves were generated with measured heat fluxes up to 100W/cm² . The inlet conditions of temperature, velocity, and pressure were maintained …

Development Of A Statistical Model For Process Control To Eliminate Sink Marks In Injection Molded Products, Kurt Frederick Hayden

Masters Theses

Customer demands for high-quality, defect-free injection-molded products are ever increasing. In order to satisfy these quality requirements, much effort is spent monitoring and controlling variable data such as cycle time, part weight, and dimensions. Attribute defects such as sink or splay are often overlooked in the development of process control systems. However, customers reject products because of these attribute defects. Industrial control systems based upon process variables and product design variables can detect conditions that may result in the molding of products with attribute defects. The systems can then correct the process prior to the molding of these defective products. …

A Training Sample Sequence Planning Method For Pattern Recognition Problems, Chen-Wen Yen, Chieh-Neng Young, Mark L. Nagurka

Mechanical Engineering Faculty Research and Publications

In solving pattern recognition problems, many classification methods, such as the nearest-neighbor (NN) rule, need to determine prototypes from a training set. To improve the performance of these classifiers in finding an efficient set of prototypes, this paper introduces a training sample sequence planning method. In particular, by estimating the relative nearness of the training samples to the decision boundary, the approach proposed here incrementally increases the number of prototypes until the desired classification accuracy has been reached. This approach has been tested with a NN classification method and a neural network training approach. Studies based on both artificial and …

Tensile Properties Of Martensitic Stainless Steels At Elevated Temperatures, Ajit K. Roy, Srinivasarao R. Kukatla, Bhagath Yarlagadda, V. N. Potluri, Martin Lewis, Brendan O'Toole

Mechanical Engineering Faculty Research

Tensile properties of quenched and tempered martensitic alloys EP-823, HT-9, and 422 were evaluated at temperatures ranging from ambient to 600 °C as a function of three different tempering times. The results indicated that the yield strength, ultimate tensile strength, and the failure strength were gradually reduced with increasing temperature. The ductility parameters were enhanced at elevated temperatures due to increased plastic flow. However, the tempering time did not significantly influence these properties. The evaluation of the fracture surfaces by scanning electron microscopy revealed reduced cracking and dimpled microstructures, indicating enhanced ductility at higher testing temperatures.

Residual Stress Characterization In Structural Materials By Destructive And Nondestructive Techniques, Ajit K. Roy, Anand Venkatesh, Vikram Marthandam, Satish Dronavalli, Douglas P. Wells, Ronald Rogge

Mechanical Engineering Faculty Research

Transmutation of nuclear waste is currently being considered to transform long-lived isotopes to species with relatively short half-lives and reduced radioactivity through capture and decay of minor actinides and fission products. This process is intended for geologic disposal of spent nuclear fuels for shorter durations in the proposed Yucca Mountain repository. The molten lead-bismuth-eutectic will be used as a target and coolant during transmutation, which will be contained in a subsystem vessel made from materials such as austenitic (304L) and martensitic (EP-823 and HT-9) stainless steels. The structural materials used in this vessel will be subjected to welding operations and …

Synthesis Dibenzyl Terephthalate Through Depolimerization Of Poly (Ethylene Terephthalate) As Alternative Of Waste Plastics Recycling, Suwardi Suwardi, Crys Fajar Partana, Agus Salim, Dyah Anitasari

Makara Journal of Technology

Synthesis Dibenzyl Terephthalate Through Depolimerization of Poly(ethylene terephthalate) as Alternative of Waste Plastics Recycling. Synthesis dibenzyl terephathalate were done through PET degradation by refluxing in benzyl alcohol at 145oC temperature for 20, 24, and 28 hours in the presence of zinc acetate catalyst. The result of degradation was purified by recristalization in methanol and then melting point (mp), FTIR, 1H NMR spectra, and TLC spot were determined. The melting point of product degradation for 28 hours was 98-99 oC. Based FTIR spectra known that compunds of product degradation have OH, C=O, C-O, CH, monosubstituted benzene, disubstituted benzene groups, while on …

Dipole Magnetization Effect To Kerosene Characteristics, Mochamad Chalid, Nelson Saksono, Adiwar Adiwar, Nono Darsono

Makara Journal of Technology

Dipole Magnetization Effect to Kerosene Characteristics. Investigation of kerosene characteristics has been done by ex-situ dipole magnetization. The results show that magnetization technique can be able to influence kerosene characteristics. Polarity and viscosity of the kerosene are observed by measuring refractive index and viscosity. An hour of 4330 Gauss flux magnetic will increase refractive index from 1.447 to 1.449 and decrease the viscosity from 1.278 to 1.256. Those changing support de-clustering occurrence and polarity increment of kerosene molecule. Gas chromatography and infrared result show that those changing do not alter kerosene structure and composition.

Study Of 2d And 3d Optical Beam Induced Voltage Imaging Using Photoresistor Sensor, Warsito Warsito, Sri Wahyu Suciyati, Susi Harnani, Akhmad Dzakwan

Makara Journal of Technology

Study of 2D and 3D Optical Beam Induced Voltage Imaging Using Photoresistor Sensor. This article shows a method to study OBIV (optical beam induced voltage) imagerie system, that usually employ a laser scanning microscopy system. The OBIV imagerie system developed use a photoresistor sensor as a sample and simultaneously it can be used for analyzing its inhomogeneity response. Resolution of the system is still low, about 350μm due to high value of incident light diameter. The results inform that photoresistor sensors gave an optimum response if the incident light hits the center of sensible zone.

Flexi Radio Base Station (Rbs) Performance Analysis Of Voice And Trafic On Kota 2 Jakarta Barat Base Station Control (Bsc), Mushfar Ferdian, Fitri Yuli Zulkifli

Makara Journal of Technology

Flexi Radio Base Station (RBS) Performance Analysis of Voice and Trafic on Kota 2 Jakarta Barat Base Station Control (BSC). The CDMA 2000 technology uses circuit switch method to handle voice traffic and packet switch method to handle data traffic between the user and RBS (Radio Base Station). These two parameters can be used to measure performance of the network generally, so it is necessary to optimize them. This paper analyze the performance of RBS by measuring its parameters such as set up failure ratio, drop ratio, and occupancy. Furthermore, the traffic increment is calculated too in order to provide …