Engineering Commons^™

Nebraska Summary: S666 New Holland T6020 Delta, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S665 Case-Ih Maxxum 125 Value, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S663 Case-Ih Maxxum 100 Value, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S688 New Holland T6020 Plus, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S689 New Holland T6030 Plus, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S678 Case-Ih Maxxum 120 Pro, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S683 New Holland T6040 Elite As, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S693 Agco Rt110 A, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Phase-Locked Piv Investigation Of The Effects Of The Blowing Ratio Of A Pulsed Vortex Generator Jet In A Low-Pressure Turbine, Nathan Michael Woods

Browse all Theses and Dissertations

At very high altitudes the Reynolds number flow through the low pressure turbine section of the gas turbine engine can drop below 25,000. At these low Reynolds numbers the flow is laminar and extremely susceptible to separation which can lead to increased losses and reduced lift. Small jets of air injected through the suction surface of the airfoil, called Vortex Generator Jets (VGJs), have been shown successful in suppressing separation and maintaining attached flow. Pulsing of these jets has been shown to be as effective as steady jets while reducing the amount of mass flow needed. An experiment using Particle …

Characterization And Modeling Methodology Of Polytetrafluoroethylene Based Reactive Materials For The Development Of Parametric Models, Stephen D. Rosencrantz

Browse all Theses and Dissertations

Certain materials, when impacting a target at high velocity will chemically react due to the shock wave passing through them, thereby increasing the damage done by the material. In particular, the reactive materials of interest are capable of acting as both structure and explosive, allowing them to achieve an effect similar to a High Explosive Incindiary (HEI), without the complexity and added mass of fuses. There are a large number of materials/material combinations that could be used in reactive munitions. The purpose of this effort is to determine an efficient analytical characterization methodology that can be validated with a minimal …

Deck-Mounted Steel Post Barrier System, John D. Reid, Ronald K. Faller, Jason A. Hascall

Department of Mechanical and Materials Engineering: Faculty Publications

An existing mountable safety barrier system, previously crash tested successfully on a wood bridge deck, was evaluated for use on a fiber reinforced plastic (FRP) bridge deck. In an attempt to avoid expensive full-scale crash testing, components of the existing system were evaluated using worst case conditions on two dynamic bogie crash tests and a series of computer simulations using nonlinear finite-element analysis. Simulation results closely approximated the physical results, with both displaying similar deformation, damage, and force levels. Both testing and simulation demonstrated that the barrier should function sufficiently if used on the FRP deck system. Further, the development …

Accelerated Testing Method For Pem Fuel Cell Based Uninterrupted Power Supply Systems, Xinyu Huang, Xiaofeng Wang

Faculty Publications

Proton exchange membrane fuel cell based power systems are on the verge of commercialization for a number of niche applications where batteries are traditionally used. Uninterrupted power supply (UPS) for wireless communication towers and broadband network relay utilities is one of the targeted application of fuel cell power systems with capacity ranging from one to serveral kilowatts. It is believed that fuel cell based UPS systems can offer considerable advantage when extended backup time is desirable. In order to replace the well-known battery based UPS systems, the reliability and perofrmance of fuel cell based UPS system need to be thoroughly …

Short-Term Reliability Of A Thin Film Resistance Temperature Detector (Rtd), Julian W. Post, Jr.

Theses and Dissertations

The primary focus of this dissertation was on the short term reliability of a thin film resistance temperature detector (RTD). As a first step, the transient and steady state temperature response of an encapsulated, thin-film RTD, which was used as a micro heater, have been characterized for a range of pressures and applied voltages, while placed on thermally insulating and conductive platforms. A user-friendly model was used to capture the three major mechanisms of heat transfer from the device (i.e. conduction, convection, and radiation). The calibration parameters of the model allowed the different modes of heat transfer to be quantified. …

Meso-Machining Of Miniature Space System Components, Carlos Ramirez

Open Access Theses & Dissertations

Many industries in engineering and science are focusing more on producing mechanisms and system components of magnitudes smaller than existing products. One of the major technologies associated with these demands is the development of meso scale precision manufacturing systems. Meso scale fabrication involves the scaling down of conventional machining to incorporate the use of familiar materials, such as aluminum, steel, and even titanium for machining miniature components. New techniques in meso scale fabrication allow for the machining of miniature space system components in an efficient manner to meet certain specifications. A description of the processes used to accurately machine a …

Characterization And Flow Physics Of Plasma Synthetic Jet Actuators, Arvind Santhanakrishnan

University of Kentucky Doctoral Dissertations

Plasma synthetic jet actuators are investigated experimentally, in which the geometrical design of single dielectric barrier discharge (SDBD) plasma actuators is modified to produce zero-mass flux jets similar to those created by mechanical devices. The SDBD plasma actuator consists of two rectangular electrodes oriented asymmetrically and separated by a layer of dielectric material. Under an input of high voltage, high frequency AC or pulsed DC, a region of plasma is created in the interfacial air gap on account of electrical breakdown of the ambient air. A coupling between the electric field in the plasma and the neutral air near the …

Plasma Treatment Of Bulk Nb Surface In The Ar/Cl2 Discharge, M. Rašković, L. Vuskovic, S. Popovic, A.-M. Valente-Feliciano, L. Phillips

Physics Faculty Publications

The preparation of the cavity walls has been one of the major challenges in the superconducting radio-frequency (SRF) accelerator technology. Therefore, constant research and development effort is devoted to develop surface preparation processes that will improve roughness and lower the level of impurities, like hydrogen or oxygen, embedded in bulk Nb, having in the same time reasonable etching rates. Plasma based surface modification provides an excellent opportunity to achieve these goals. We present Ar/Cl₂ discharge treatment of bulk Nb where we achieved etching rates comparable to the rates obtained with the electropolishing method without introducing impurities in Nb. The …

Development Of A Liquid Injection Propane System For Spark-Ignited Engines Via Fuel Temperature Control, Brian Charles Applegate

Masters Theses

"This work describes the development of a thermally controlled liquid propane injection system...A liquid fuel system, as described in this work, offers power gains over vaporized fuel introduction due to the ability to use the heat of vaporization from the vaporizing fuel to cool the intake charge and improve the volumetric efficiency of the engine. This system uses temperature to control the state of the fuel in the fuel system"--Introduction, page 1.

On-Line Inspection And Thermal Properties Comparison For Laser Deposition Process, Yu Yang

Masters Theses

"This thesis is focused on comparing the laser deposition cladding with intended design model and comparing the effect of laser deposition process on thermal properties with traditional welding process. It is research on two aspects of laser deposition cladding. The first part of the thesis is aimed at solving the geometric inspection of laser deposition cladding, and the second part is for comparing the thermal properties of laser deposition cladding to samples of conventional welding process"--Introduction, page 1.

Thermal Effectiveness Characteristics Of Low Approach Indirect Evaporative Cooling Systems In Buildings, Ben Costelloe, Donal Finn

Articles

Meteorological enthalpy analysis of temperate and maritime climates above latitude 45°N suggests that the water-side evaporative cooling technique has considerable unrealised potential with contemporary “high temperature” building cooling systems—such as chilled ceilings and displacement ventilation. As low approach conditions are the key to exploiting the cooling potential of the ambient air, thermal performance at such conditions needs to be investigated. To address the research issues, an industrial scale test rig, based on a low approach open cooling tower and plate heat exchanger and designed to maximise evaporative cooling potential, has been constructed. The thermal effectiveness of such systems (as a …

Thermal Control Of An Occupied Room: Investigating The Use Of Carbon Dioxide Concentration As An Auxiliary Control Variable, Kevin O'Connell, Aidan O'Dwyer

Conference papers

This paper details the theoretical and experimental work done in the examination of the relationship between human generated carbon dioxide concentration and temperature rise in an occupied room. Generation of carbon dioxide by humans is linked to metabolic rate and heat generation. Therefore, carbon dioxide concentration may be used as an indicator of occupancy in a room. Typically, a heating control system will react slowly to changes in room occupancy if temperature is used as the process variable. The aim of the work was to establish if carbon dioxide concentration in the space could be used as an auxiliary control …

Granular Contact Lubrication: Theory And Experiment, Karim El Kholy

LSU Doctoral Dissertations

This dissertation is devoted to a theoretical and experimental study of the granular contact lubrication, both. The theory is based on the kinetic of the granular material where the granules interact with each other and with the boundary surfaces through instantaneous, binary collisions, characterized by a constant coefficient of restitution. Specifically this study focuses on granular lubrication in Couette flows. A series of simulations is reported and the results show good agreement with several published papers. Also, a theory that ties the true temperature to the grain mobility is developed. The true temperature of a granular material depends on the …

Development Of Micropump For Microfluidic Applications, Dong Eun Lee

LSU Doctoral Dissertations

This dissertation covers the research work on two types of micropumps, one is based on magnetohydrodynamic (MHD) principle that utilizes Lorentz force for actuation, and the other is based on electrochemical actuation. The AC-type MHD micropump was designed and analyzed as a solution to the bubble formation problem encountered in DC-type MHD micropump. A UV-LIGA process using thick layer of SU-8 negative photoresist was successfully developed to microfabricate the AC MHD micropump. Preliminary studies and tests of the AC MHD micropumps demonstrate that bubble formation was significantly reduced to permit the proper function of the micropump. A continuous flow was …

Characterization Of Advanced Composites- A Nondestructive Approach, Phani Surya Kiran Mylavarapu

LSU Doctoral Dissertations

Adhesively bonded sandwich structures comprising of particulate composites as core and graphite epoxy skins as stiffeners are widely used for various applications in the marine and aerospace industry. The core material and the stiffener are held together by an adhesive bond. Particulate composites are made from a mixture of a polymer resin and hollow or solid particles. Hollow particulate composites are known as syntactic foams. Particulate composites possess attractive mechanical and physical properties such as high compressive strength etc, making them attractive materials for use in structural applications. Characterization of the adhesive bondline and core material in sandwich structures is …

Eigenvalue Optimization And Its Applications In Buckling And Vibration, Srinivas Gopal Krishna

LSU Doctoral Dissertations

Eigenvalue problems are of immense interest and play a pivotal role not only in many fields of engineering but also in pure and applied mathematics. An in-depth understanding of this class of problems is a pre-requisite for vibration and buckling analyses of structures. Design optimization of structures to prevent failure due to instability (bucking) and vibration introduces the problem of determining optimal physical parameters such that load carrying capacity or the fundamental natural frequency is maximized. A classical example of such problems is the Lagrange problem of determining the shape of the strongest column against buckling. The primary objective of …

An Investigation Of The Frictional And Thermal Behavior Of Oscillatory Sliding Line Contacts, Mongi Mansouri

LSU Doctoral Dissertations

This research deals with an experimental and numerical investigation of the frictional and thermal behavior of pin-bushing pairs, operating at reciprocating sliding motion or under heavy loads. Large interfacial temperatures developed due to frictional heating can cause failure. Therefore, numerical prediction and analysis of the surface temperature under various operating conditions are important. Laboratory tests using a pin-bushing tester provided measurements of the friction coefficient and temperature. Hard coated and plain (uncoated) bushings, both made of induction hardened stainless steel, were tested. Lower coefficient of friction and surface temperature were observed in the case of the coated bushing. In the …

Adhesion-Delamination Mechanics Of Linear And Axisymmetric Film At Film-Substrate Interface, Ming-Fung Wong

Masters Theses

"This thesis is to characterize the thin membrane adhesion-delamination phenomena which occur in biological cells and micro-electro-mechanical systems (MEMS) operation. The delamination of a thin film adhered to a rigid substrate is subjected to the coupling effects of tensile residual stress and interfacial adhesion energy. The adhesion-delamination mechanics is derived using the classical linear elasticity and thermodynamics energy balance. The membrane deformation is here dominated by a mixed plate-bending and membrane-stretching, while the concomitant stress is neglected. An 1-dimensional model is first investigated where a pre-stressed rectangular film clamped at both ends delaminates from a rigid punch of the same …

Selective Laser Sintering Of Stearic Acid-Coated Alumina Ceramic, Jason J. Nolte

Masters Theses

"The purpose of this research is to develop a process that will enable a Selective Laser Sintering (SLS) machine to create geometrically complex green parts of various sizes that become strong, dense ceramic parts after sintering. This will be applicable to SLS systems already operational in industry, and may offer a more cost-effective, more time-efficient method for producing high-temperature ceramic rapid prototype parts. Alumina was the chosen ceramic for the developmental stage of this research. Fine alumina powder (average particle size of 0.4 µm) was coated with stearic acid, which served as a binder. Green parts were made from this …

Robust Mechanism Synthesis With Random And Interval Variables, Pavan Kumar Venigella

Masters Theses

"Robust mechanism synthesis ensures that the performance of a mechanism is not sensitive to uncertainties in the mechanism and its environment. The uncertainties include the dimension variations, installation errors, random input motion, and various external forces. Robust mechanism synthesis is used to minimize the impact of these uncertainties on the mechanism performance. Robust mechanism synthesis has been performed by either a probabilistic approach or a worst case approach. The former approach describes uncertain parameters as random variables while the latter approach treats uncertain parameters as interval variables. In this work, methods are developed for robustness assessment and robust mechanism synthesis …

Empirical Dynamic Modeling And Nonlinear Force Control Of Friction Stir Welding, Xin Zhao

Masters Theses

"Current Friction Stir Welding (FSW) process models are mainly concerned with the detailed analysis of material flow, heat generation, etc. and therefore, are computationally intensive. Dynamic models describing the total forces acting on the tool throughout the entire welding process are required for the design of feedback control strategies and improved process planning and analysis. In this thesis, empirical models relating the process parameters (i.e., plunge depth, travel speed, and rotation speed) to the process variables (i.e., axial, path, and normal forces) are developed to describe their dynamic relationships"--Abstract, page iv.

Modeling And Control Of Freeze-Form Extrusion Fabrication, Xiyue Zhao

Masters Theses

"Freeze-form Extrusion Fabrication (FEF) is an additive manufacturing technique that extrudes ceramic loaded aqueous pastes layer by layer below the paste freezing temperature for component fabrication. As the FEF is aimed at being conducted at low environmental temperatures, down to -20°C, it is necessary to investigate the effect of environmental temperature on the process. The advantages of fabrication at low temperature have been proved by experiments. Comparisons in terms of operation parameters, self-sustaining ability, and system dynamic response were performed at different environmental temperatures ranging from 20°C to -20°C.

It is commonly known in paste extrusion processes that due to …