Engineering Commons^™

The Potency Of Fire And Explosion Hazard On Premium Oil Storage Tank At Depot X 2007, Fatma Lestari, Warid Nurdiansyah

Makara Journal of Technology

The Potency of Fire and Explosion Hazard on Premium Oil Storage Tank at Depot X 2007. Premium oil storage tanks have fire and explosion risk because Premium oil is flammable liquid. Because of that, fire and explosion risk assessment on Premium oil storage tank at Depot X is needed as foundation to fire and explosion risk management, and comply with regulations. Method of this research is Dow’s Fire and Explosion Index. This research indicate that F&EI value for Premium oil storage tank is 118,82. Based on that F&EI value, level of risk at Premium oil storage tank is intermediate risk.

Limiting Maximum Drag Reduction Asymptote For The Moment Coefficient Of An Enclosed Rotating Disk With Fine Spiral Grooves, Budiarso Budiarso, Keizo Watanabe, Satoshi Ogata

Makara Journal of Technology

In this study, the limiting maximum drag reduction asymptote for the moment coefficient of an enclosed rotating disk with fine spiral grooves in turbulent flow region were obtained analytically. Analysis which were based on an assumption for a simple parabolic velocity distribution of turbulent pipe flow to represent relative tangential velocity, was carried out using momentum integral equations of the boundary layer. For a certain K- parameter the moment coefficient results agree well with experimental results for maximum drag reduction in an enclosed rotating disk with fine spiral grooves and drag reduction ratio approximately was 15 %. Additionally, the experimental …

Co2 Absorption From Its Mixture With Ch4 Or N2 Through Hollow Fiber Membrane Contactor Using Water As Solvent, Sutrasno Kartohardjono, Anggara Anggara, Subihi Subihi, Yuliusman Yuliusman

Makara Journal of Technology

CO2 Absorption from Its Mixture with CH4 or N2 through Hollow Fiber Membrane Contactor using Water as Solvent. Hollow fiber membrane contactors have been widely used as gas-liquid contactors recently such as in the CO2 absorption process from gas stream. This research aims to evaluate the effectiveness of hollow fiber membrane contactor to absorb CO2 from its mixture with CH4 or N2 using water through mass transfer and hydrodynamic tests. There are 3 membrane modules used in this research with shell diameter of 1.9 cm, length of 40 cm, outer fiber diameter of 2.7 mm and fiber number in the …

Trajectory Shaping Of Surface-To-Surface Missile With Terminal Impact Angle Constraint, S. Subchan

Makara Journal of Technology

This paper presents trajectory shaping of a surface-to-surface missile attacking a fixed with terminal impact angle constraint. The missile must hit the target from above, subject to the missile dynamics and path constraints. The problem is reinterpreted using optimal control theory resulting in the formulation of minimum integrated altitude. The formulation entails nonlinear, two-dimensional missile flight dynamics, boundary conditions and path constraints. The generic shape of optimal trajectory is: level flight, climbing, diving; this combination of the three flight phases is called the bunt manoeuvre. The numerical solution of optimal control problem is solved by a direct collocation method. The …

Analysis Of Three Phase Controlled Rectifier With The Same Distance Control As Compared To The Same Angle Control, Sudirman S., Sri Kurniati A.

Makara Journal of Technology

Analysis of three phase controlled rectifier with the same distance control as compared to the same angle control. This research aim to compare the firing of the same distance and the same angle control at three phase controlled rectifier with seen generated harmonic at input (AC side). Then calculate of rectifier efficiency and power factor comparison from both the control type. The rectifier use passive filter with resistance 11 ohm and is analysed with program simulation using PSPICE version 7.1. Result of research indicate that use of the same distance control generates the 5th and 7th harmonics, while the same …

The Use Of Red Cabbage’S Anthocyanine Extract As A Photosensitizer On A Dye-Sensitized Nanocrystalline Tio2 Solar Cell, Akhiruddin Maddu, Mahfuddin Zuhri, Irmansyah Irmansyah

Makara Journal of Technology

The use of Red Cabbage’s anthocyanine extract as a photosensitizer on a Dye-Sensitized Nanocrystalline TiO2 Solar Cell. A solid-state dye-sensitized nanocrystalline TiO2 solar cell utilizing anthocyanin extract form red cabbage as photosensitizer was fabricated. The solar cell was formed in sandwich structure, which two electrodes sandwiching polymer electrolyte containing a redox couple (I-/I3 -). One of the electrodes, namely working electrode, TiO2 layer on TCO (transparent conducting oxide) coated glass substrate was sensitized with anthocyanin dye as electron donor in the system. Another electrode was a carbon sheet as a counter electrode. Gel electrolyte based on PEG (polyethylene glycol) containing …

Effect Of Contact Time On Interface Reaction Between Aluminum Silicon (7% And 11%) Alloy And Steel Dies Skd 61, Bambang Suharno, Neni Octapiani Nurhayati, Bustanul Arifin, Sri Harjanto

Makara Journal of Technology

Effect of Contact Time on Interface Reaction between Aluminum Silicon (7% and 11%) Alloy and Steel Dies SKD 61. Die soldering (die sticking) is a defect of metal casting in which molten metal “welds” to the metallic die mold surface during casting process. Die soldering is the result of an interface reaction between the molten aluminum and the die material. Aluminum alloy with 7 and 11% silicon and SKD 61 die steel are the most common melt and die material used in aluminum die casting. This research is done to study the morphology and the characteristics of the formed AlxFeySiz …

In-House Development Of Scheduling Decision Support Systems: Case Study For Scheduling Semiconductor Device Test Operations, Tali Freed, K. H. Doerr, T. Chang

Industrial and Manufacturing Engineering

Most manufacturing processes can benefit from an automated scheduling system. However;: the design of a fast, computerised scheduling system that achieves high-quality results and requires minimal resources is a difficult undertaking. Efficient .. scheduling of a semiconductor device test facility requires an information system that provides good schedules quickly. Semiconductor device testing-is the last stage of the long semiconductor manufacturing process, and therefore. is subjected to customer service pressures. The cost of an off-the-shelf computerised scheduling system may he prohibitive for many companies. In addition, many companies are taken aback by other characteristics of off-the-shelf scheduling systems, such as code …

Fabrication Of Functionally Graded 3a/5a Zeolites By Electrophoretic Deposition, X. Wang, E. A. Olevsky, E. Bruce, M. B. Stern, D. T. Hayhurst

Industrial and Manufacturing Engineering

Functionally graded zeolites of molecular sieve type 3A and 5A are deposited by electrophoretic deposition (EPD) from acetone suspension with 8% volume concentration of n-butylamine as particle charging agent. The EPD characteristics of both 3A and 5A suspensions are studied. Functionally graded zeolite 3A/5A deposits are obtained at 200 V DC. Energy dispersive X-ray dispersion (EDX) analysis results confirm the graded structure. The deposited zeolites are also analysed by scanning electron microscopy (SEM). The factors influencing the deposition process are discussed.

Context-Aware Inference System To Capture Design Rationale From Legacy Mcad, Ganeshram Ramji Iyer

Mechanical and Aerospace Engineering Dissertations - Archive

There exist numerous design rationale systems that convert captured information into structured design rationale while providing rationale representation and retrieval. These systems woefully neglect the design rationale that is present in legacy CAD such as 2D drawings and 3D models. The dissertation addresses the issues that arise when dealing with the capture, representation and retrieval of design rationale from the 2D legacy CAD data, specifically the non-form related data (e.g. text and symbols). A definition for design rationale in the CAD domain is presented which forms the basis of the proposed approach. The approach uses a unique context-aware inference system …

Commissioning High Performance Residences In Hot, Humid Climates, Florida Solar Energy Center, Ken Fonorow

FSEC Energy Research Center®

Since 2001, the authors have engaged several builders in the Gainesville, FL area to build over 500 high performance new energy efficient homes in multiple sub divisions. The builders keep building to increased levels of energy efficiency. Each home is individually designed, inspected, rated and commissioned for optimum performance. This paper summarizes the experiences to date with two production builders who have cost shared with the Building America program to deliver these outstanding results. Keys to success are commitment from the final decision maker; scopes of work for subcontractors with specific performance criteria; clear communication with the trades often accompanied …

Closing The Gap: Getting Full Performance From Residential Central Air Conditioners. Task 4.2-Develop New Climate-Sensitive Air Conditioner, Design, Construction, And Testing, Florida Solar Energy Center, Don B. Shirey Iii

FSEC Energy Research Center®

This study evaluated the performance of a prototype air conditioning system. The configuration of the prototype was based on detailed simulation results performed as part of this study. The results of the previously completed simulation indicated that energy-efficient, properly-ventilated homes in humid climates need equipment options or configurations that can provide a modest amount of additional dehumidification capacity while coordinating their operation with conventional cooling and ventilation systems. A prototype air conditioning system was constructed using currently available components and provides a method to independently control sensible (temperature) and latent (moisture) building loads. The prototype system was tested in both …

On Internal Cone Cracks Induced By Conical Indentation In Brittle Materials, J. Yan, Anette M. Karlsson, X. Chen

Mechanical Engineering Faculty Publications

The conditions for cone cracks to develop due to a conical indentation are investigated. Axisymmetric numerical simulations, based on the finite element method, are conducted, assuming a linear-elastic, perfectly plastic material. A superposition scheme is employed to simulate a range of crack geometries, including various lengths and orientations. The results indicate that the class of cracks investigated is prone to develop internally in brittle materials. Based on a reversed analysis, a new technique is proposed for measuring the fracture toughness in bulk material and thick coatings through one simple indentation test when the cone crack appears.

The Effect Of Tibiofemoral Loading On Proximal Tibiofibular Joint Motion, Jacob Scott, Ho Lee, Wael Barsoum, Antonie J. Van Den Bogert

Mechanical Engineering Faculty Publications

The human proximal tibiofibular joint (PTFJ) and its relationship to overall knee joint mechanics have been largely unexplored. This study describes force/displacement data from experiments done on four human cadaveric knee specimens and general conclusions obtained with the help of a statistical modeling technique. Specimens were rigidly affixed at the tibia to a force plate and the femur was attached to a custom made device allowing for manual load application. Motion of the fibular head was tracked relative to the tibial plateau by means of reflective markers and a high speed digital camera synchronized with the force plate data stream. …

Thermal Testing Of Building Insulation Materials, Eoghan Frawley, David Kennedy

Articles

This article explores the testing of building insulation materials and the development of a suitable testing apparatus.

Experimental Validation Of An Autonomous Control System On A Mobile Robot Platform, Timothy Mclain, Randall W. Beard, Wei Ran, J.-S. Sun

Faculty Publications

An autonomous control system designed for a non-holonomic wheeled mobile robot that is programmed to emulate a fixed-wing unmanned air vehicle (UAV) flying at constant altitude is experimentally validated. The overall system is capable of waypoint navigation, threat avoidance, real-time trajectory generation and trajectory tracking. Both the wheeled mobile robot experimental platform and the hierarchical autonomous control software architecture are introduced. Programmed to emulate a fixed-wing UAV flying at constant altitude, a non-holonomic mobile robot is assigned to follow a desired time-parameterised trajectory generated by a real-time trajectory generator to transition through a sequence of targets in the presence of …

High Temperature Heat Exchanger Project: Quarterly Progress Report July 1, 2007 Through September 30, 2007, Anthony Hechanova

Publications (NSTD)

• Ceramatec Sulfuric Acid Decomposer. The numerical model of a SiC ceramic coupon with two layers of microchannels was developed. Calculations of the factor of safety and probability of failure for the case of a straight channel were performed. Results for a pressure of 7.5 MPa were performed. The thermal and mechanical stress analyses of the Ceramatec HTHX and decomposer were completed.

• Bayonet Heat Exchanger. The thermal and mechanical stress analyses of the bayonet type HTHX and decomposer (Sandia design) were completed. Temperature profiles obtained from thermocouples measured from the Sandia experiments have been applied to the whole packed …

Nanoindentation Of The A And C Domains In A Tetragonal Batio3 Single Crystal, Young-Bae Park, Matthew J. Dicken, Zhi-Hui Xu, Xiaodong Li

Faculty Publications

Nanoindentation in conjunction with piezoresponse force microscopy was used to study domain switching and to measure the mechanical properties of individual ferroelectric domains in a tetragonal BaTiO₃ single crystal. It was found that nanoindentation has induced local domain switching; the a and c domains of BaTiO₃ have different elastic moduli but similar hardness.Nanoindentationmodulus mapping on the a and c domains further confirmed such difference in elasticity. Finite element modeling was used to simulate the von Mises stress and plastic strain profiles of the indentations on both a and c domains, which introduces a much higher stress level than …

Integrated Piezoresistive Sensing For Feedback Control Of Compliant Mems, Robert K. Messenger

Theses and Dissertations

Feedback control of MEMS devices has the potential to significantly improve device performance and reliability. One of the main obstacles to its broader use is the small number of on-chip sensing options available to MEMS designers. A method of using integrated piezoresistive sensing is proposed and demonstrated as another option. Integrated piezoresistive sensing utilizes the inherent piezoresistive property of polycrystalline silicon from which many MEMS devices are fabricated. As compliant MEMS structures flex to perform their functions, their resistance changes. That resistance change can be used to transduce the structures' deflection into an electrical signal. This dissertation addresses three topics …

Effect Of Surface Roughness On Rate-Dependent Slip In Simple Fluids, Nikolai V. Priezjev

Mechanical and Materials Engineering Faculty Publications

Molecular dynamics simulations are used to investigate the influence of molecular-scale surface roughness on the slip behavior in thin liquid films. The slip length increases almost linearly with the shear rate for atomically smooth rigid walls and incommensurate structures of the liquid/solid interface. The thermal fluctuations of the wall atoms lead to an effective surface roughness, which makes the slip length weakly dependent on the shear rate. With increasing the elastic stiffness of the wall, the surface roughness smoothes out and the strong rate dependence is restored again. Both periodically and randomly corrugated rigid surfaces reduce the slip length and …

A Generalized Two-Dimensional Model To Reconstruct The Impact Phase In Automobile Collisions, Regis Agenor David

Theses and Dissertations

Automobile accident reconstruction has been facilitated by the development of computer based modules to allow evaluation of evidence gathered at the accident scenes. Although the computer modules are based in fundamental physical laws, an understanding of these laws by the user is required for proper application of the computer model in a given accident scenario. Vehicle collision analysis techniques generally separate the collision into three phases: pre-impact, impact, and post impact. The intent of the research is to provide a generalized model to reconstruct two dimensional impact problems in the area of accident reconstruction. There are currently two modeling techniques …

Optimal Control Of Class Of Non-Linear Plants Using Artificial Immune Systems: Application Of The Clonal Selection Algorithm, S. A. Panimadai Ramaswamy, Ganesh K. Venayagamoorthy, S. N. Balakrishnan

Electrical and Computer Engineering Faculty Research & Creative Works

The function of natural immune system is to protect the living organisms against invaders/pathogens. Artificial Immune System (AIS) is a computational intelligence paradigm inspired by the natural immune system. Diverse engineering problems have been solved in the recent past using AIS. Clonal selection is one of the few algorithms that belong to the family of AIS techniques. Clonal selection algorithm is the computational implementation of the clonal selection principle. The process of affinity maturation of the immune system is explicitly incorporated in this algorithm. This paper presents the application of AIS for the optimal control of a class of non-linear …

Ole Miss Engineer 2007

Ole Miss Engineer

No abstract provided.

Simulation And Fabrication Of Three Novel Micromechanical Sensors, Yanqing Lu

Doctoral Dissertations

This work focuses on the simulation, fabrication and characterization of novel microdevices for chemical and biological sensors for improved sensitivity, enhanced performance and applicability. Specifically, microbridge and microcoil sensors have been fabricated via advanced microfabrication technologies. Due to the potential application in chemical and biological sensing, the growth of gold and platinum nanowires during an electrolysis process have also been investigated.

A microbridge can be considered as the head-to-head fusion of two cantilevers and the middle of the bridge would deform in a way similar to a microcantilever. The microbridge sensing device is more stable than the microcantilever, especially in …

On The Reference Length And Mode Mixity For A Bimaterial Interface, A. Agrawal, Anette M. Karlsson

Mechanical Engineering Faculty Publications

We investigate properties that govern interfacial fracture within the framework of linear elastic fracture mechanics, including interfacial fracture toughness, mode mixity,and the associated reference length. The reference length describes the arbitrary location where the mode mixity is evaluated, ahead ofthe crack tip, in a bimaterial system. A method for establishing a reference length that is fixed for a given bimaterial system is proposed. This is referred to as the“characteristic reference length,” with the associated “characteristic mode mixity.” The proposed method is illustrated with an experimental investigation, utilizing a four-point bend test of a bimaterial system.

Effect Of Cold Work On The Tensile Properties Of 6061, 2024, And 7075 Al Alloys, D. Ortiz, M. Abdelshehid, R. Dalton, J. Soltero, R. Clark, M. Hahn, E. Lee, W. Lightell, B. Pregger, J. Ogren, P. Stoyanov, Omar S. Es-Said

Mechanical Engineering Faculty Works

Aluminum alloys 6061, 2024, and 7075 were heat treated to various tempers and then subjected to a range of plastic strain (stretching) in order to determine their strain limits. Tensile properties, conductivity, hardness, and grain size measurements were evaluated. The effects of the plastic strain on these properties are discussed and strain limits are suggested.

Electroactive Polymers (Eap): Simulation Studies Of The Actuation Mechanisms In A Cantilever Cellulose Electroactive Paper, Fatim A. Mbaye

Electrical & Computer Engineering Theses & Dissertations

Electroactive polymers (EAPs) exhibit large strain in response to an external electric field and have attracted a great deal of attention in recent years for sensor and actuator applications. Favorable properties include soft actuation, ease and simplicity in manufacturing, being light-weight, low power consumption, and the ability to withstand harsh environments. However, this is an emerging material, and several aspects, including the fundamental mechanisms for piezoelectric deflections, remain unclear. This project studies the internal electromechanical factors that contribute to the voltage induced deflections of electro-active paper (EAPap). Experimental measurements of bias dependent deflections and water absorption as a function of …

Effects Of Heat Treatments On Steels For Bearing Applications, K. Clemons, C. Lorraine, G. Salgado, A. Taylor, J. Ogren, P. Umin, Omar S. Es-Said

Mechanical Engineering Faculty Works

AISI 52 100, 440C, REX20, and Crucible CRU80 steel samples were exposed to 16 different heat treatments to vary the levels of retained austenite. Rockwell C hardness measurements, optical microscopy, and compression testing were used to compare the properties of the different steels.

Simulation And Thermo-Economic Analysis Of A Solar-Assisted Heat Pump System For Domestic Water Heating Application, Vaibhav D. Gagrani

Mechanical & Aerospace Engineering Theses & Dissertations

The present study examines the potential of solar-assisted heat pump (SAHP) system for domestic water heating application over conventional electrical water heating system. The focus of study is on developing a user-friendly and interactive software using Java platform with Microsoft Access being used for maintaining the database. The software developed is capable of predicting the thermal and economic performance of a SAHP system under varying conditions. The software allows the user to select the geographic location, specify condensing temperature, collector, and compressor parameters, and thermal load requirement. Location specific meteorological data, such as latitude, solar radiation, and ambient temperature, are …

Stochastic Optimization Formulations For Structure Design, Shivanandini Tanuku

Mechanical & Aerospace Engineering Theses & Dissertations

The production process and the operational environment of a product usually involve many unpredictable elements, such as the manufacturing tolerance, the service loads, the maintenance schedule, etc. Furthermore, the targeted functionality of a product can also be alternated or enhanced in its service life due to the technology advancement, new demands, or new regulation. It is thus a challenge to a designer to include these uncertainties in the early design stage of a product.

This thesis uses a simple three-bar truss problem as a vehicle to investigate the qualities of the optimal solutions resulted from various stochastic programming formulations. The …