Engineering Commons^™

Polarized Positrons At Ce⁺Baf, A. Ushakov, J. Benesch, M. Bruker, L. Cardman, J. Conway, S. Covrig Dusa, P. Degtiarenko, Y. Enomoto, S. Gessner, P. Ghoshal, S. Gopinath, J. Grames, C. Gulliford, S. Habet, G. Hays, C. Hernández-García, A. Hofler, R. Kazimi, M. Kostin, V. O. Kostroun, F. Lin, V. Lizárraga-Rubio, K. Mahler, Y. Morikawa, S. Nagaitsev, S. Ogur, G. Palacios-Serrano, N. Raut, B. Rimmer, Y. Roblin, A. Seryi, K. Smolenski, M. Stutzman, R. Suleiman, A. Sy, N. Taylor, D. Turner, A. Ushakov, C. Valerio-Lizarraga, E. Voutier, S. Wang, Y. Zhang

Mechanical & Aerospace Engineering Faculty Publications

A baseline concept for a continuous wave (CW) polarized positron injector was developed for the Continuous Electron Beam Accelerator Facility (CEBAF) at Jefferson Lab [1]. This concept is based on positron beam generation by a high current polarized electron beam (1 mA, 120 MeV, >85% polarization) irradiating a rotating water-cooled tungsten target or liquid metal target. The update on the development of the Ce⁺BAF injector concept including the polarized electron source, the development of high power targets, simulations of positron capture, the design of the transport line from the positron injector to the CEBAF North Linac and the planned experiment …

Conference Report Of Wmu Maritime Affairs Conference 2025 : Transforming A Maritime Future : Digitalization And Decarbonization, World Maritime University

Conference Papers

No abstract provided.

Anisotropic And Temperature-Tunable Second-Harmonic Vortex Generation In Ferroelectric Nbocl2 Holograms, Jayanta Deka, Xiaodong Yang, Jie Gao

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Optical vortex beams with helical phase fronts have immense potential to enhance data capacity due to the unbounded values of orbital angular momentum. Chip-scale platforms for producing vortex beams are of paramount importance for a variety of applications. On the other hand, 2D materials with unique optical properties are essential for developing multifunctional ultrathin photonic devices. Here, anisotropic and temperature-tunable second-harmonic vortex beam generation is demonstrated with ultrathin ferroelectric niobium oxide dichloride (NbOCl₂) fork holograms. The polarization-resolved Raman measurements are performed on the NbOCl₂ crystal to understand the anisotropic behavior of the Raman modes. It is demonstrated …

Machine Learning Approach For Defect Prediction In Metal 3d Printing For Aerospace Applications, Yerlik Gabdulla, Md Hazrat Ali, Frank Liou, Essam Shehab

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Additive manufacturing (AM) has revolutionized the aerospace industry by enabling the production of lightweight and high-strength components, such as aerospace engine components and structural elements. The ability to create complex geometries and reduce material waste is particularly beneficial for aerospace applications, where performance and weight reduction are paramount. However, ensuring the quality and reliability of these components remains a challenge, particularly in mass production, which is related to material quality, expensive processes, and longer computational times than conventional manufacturing methods. This paper proposes an approach utilizing a Decision Tree Classification Machine Learning Algorithm to predict the possibility of defect occurrence …

In-Situ Transmission Electron Microscopy Investigation Of Grain Size And Temperature Dependent Irradiation Behavior Of 304l Stainless Steel, Anish Ranjan, Matthew Luebbe, Nastaran Motaharinia, Wei Ying Chen, Frank Liou, Haiming Wen

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The influence of grain size, irradiation temperature, and dose on the evolution of irradiation-induced defects in austenitic 304L stainless steel (SS) was systematically investigated. Coarse-grained (CG), ultrafine-grained (UFG), and nanocrystalline (NC) specimens were exposed to irradiation doses up to 10 displacements per atom (dpa) at room temperature (RT), 300°C, and 500°C. Dislocation loop size and density were quantitatively analyzed using transmission electron microscopy, and results showed that the dislocation loop size remained comparable across different grain sizes. However, loop density was strongly dependent on the grain size. The CG specimens exhibited the highest loop density due to a limited fraction …

Nonlinear Dynamics And Control Of An Autonomously Operated Towed System, Brian Allan Carr

Wayne State University Theses

Emergency towing vessels are a vital component of maritime safety. This study works to improve on previous works in the area of automating the towing of disabled ships. In doing so control methods for transient three degree of freedom dynamics of a tug and tow system which is connected with a finite element cable are evaluated. A Heaviside unit step function is inserted to void both the elastic and viscous interaction between the massive elements whenever the distance between two neighboring masses appears to be below the corresponding undeformed distance. This follows the representation of the cable as a one-dimensional …

A Comprehensive Review Of Piezoelectric Pvdf Polymer Fabrications And Characteristics, Nadia Ahbab, Sidra Naz, Tian-Bing Xu, Shihai Zhang

Mechanical & Aerospace Engineering Faculty Publications

Polyvinylidene fluoride (PVDF) polymer films, renowned for their exceptional piezoelectric, pyroelectric, and ferroelectric properties, offer a versatile platform for the development of cutting-edge micro-scale functional devices, enabling innovative applications ranging from energy harvesting and sensing to medical diagnostics and actuation. This paper presents an in-depth review of the material properties, fabrication methodologies, and characterization of PVDF films. Initially, a comprehensive description of the physical, mechanical, chemical, thermal, electrical, and electromechanical properties is provided. The unique combination of piezoelectric, pyroelectric, and ferroelectric properties, coupled with its excellent chemical resistance and mechanical strength, makes PVDF a highly valuable material for a wide …

The Design Of A Bioinspired Impact Mitigation System Towards The Prevention Of Brain Injuries, Bryce H. Reimer

Master’s Theses

Traumatic brain injuries (TBIs), including concussions and chronic traumatic encephalopathy (CTE), remain a major concern across contact sports, military operations, and transportation. Despite advancements in protective equipment, current strategies often fall short in preventing the mechanical conditions that contribute to long-term neurological damage. This thesis presents the design and validation of a bioinspired impact mitigation system modeled after bighorn sheep horn structures, which have evolved to endure high-energy collisions without apparent brain injury.

Using biomimetic principles, the research integrates experimental and computational methods to evaluate how horn-like geometries reduce impact-induced accelerations. A custom drop tower was built to test dynamic …

Nebraska Summary #1293: Fendt 618 Vario, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary #1292: Fendt 616 Vario, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Test #2301: Claas Xerion 12.650, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Test #2298: John Deere 9rx 830, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Test #2297: John Deere 9rx 770, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Test #2296: John Deere 9rx 710, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Test# 2299: Claas Xerion 12.590, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Test #2269: Case Ih Steiger 645, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary #1298: Fendt 726 Vario Gen 7.1, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary #1294: Fendt 620 Vario, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary #1291: Fendt 614 Vario, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

In‑Situ Characterization And Modeling Of Machining‑Induced Residual Stresses In Peripheral Milling Of Ti–6al–4v With Rounded Cutting Edges, Matthias Wimmer, Julius M. Schoop, Michael F. Zaeh

Mechanical Engineering Faculty Publications

The residual stress state in the sub-surface of machined components can significantly impact the properties and performance of parts, such as tribological properties, fatigue life, and dimensional distortion. The evolution of residual stresses depends on the selected process parameters and tool geometry, which affect the thermo-mechanical load imposed on the workpiece. The cutting-edge radius is among the most important factors influencing the resulting residual stresses. In this paper, a semi-analytical model for the determination of residual stresses after peripheral milling of Ti–6Al–4V is presented. It considers the physical principles of orthogonal machining, including the complex geometric and kinematic relationships during …

Transient Thermal Finite Element Simulation For Process Modeling In Wire Arc Additive Manufacturing, Satya Sai Kumar Pilli

Dissertations, Master's Theses and Master's Reports

This thesis presents the development of a transient thermal framework for Wire Arc Additive Manufacturing (WAAM) created using ANSYS Workbench. This study aims to understand the inherent properties and thermal behavior of WAAM by using the Finite Element (FE) simulation technique to reduce the need for experiments. Specifically, the transient thermal WAAM simulation framework uses the heat source Goldak model to understand the thermal behavior for a given voltage, initial temperature, and travel speed during the process to predict process temperature. The outcomes of this thesis aim to significantly decrease material waste and repetitive experiments and accelerate production process design …

A Finite Volume-Based Approach For Modeling Hyperbaric Oxygen Therapy For Healing Chronic Wounds, Cade M. Layser

College of Graduate Studies: Theses & Dissertations

The current number of people in America with diabetes is approximately 38.4 million, that population is expected to rise to 54.9 million by 2030. Chronic wounds, which are characterized by impaired or stalled healing, are commonly associated with diabetes. These wounds if not treated properly can cause significant complications such as sepsis, infection, and gangrene which can lead to limb amputation or death of the patient. Limb amputations can be a large financial burden and significantly reduce the patient’s quality of life. The timely and efficient treatment of chronic wounds is essential to prevent adverse patient outcomes. Hyperbaric Oxygen therapy …

Defect Detection In Extrusion-Based Bio-Printed Constructs Using Video-Based Vibration Analysis, Md Anisur Rahman

College of Graduate Studies: Theses & Dissertations

Bio-additive manufacturing has emerged as a transformative advancement in biomedical engineering, enabling the fabrication of complex biological structures. However, maintaining the precision and quality of printed constructs remains a significant challenge, particularly in applications such as bioprinted organ transplants. Among the key factors affecting structural integrity, dimensional inconsistencies and interlayer defects present major obstacles, potentially compromising mechanical stability and functionality. This study explores the detection of defects caused by variations in dimensional accuracy and layer-to-layer adhesion. To address these challenges, a video-based motion estimation technique is employed as a non-contact and non-destructive evaluation method. Traditional approaches, such as contact-based and …

Synthesis And Processing Of Co-Axial/Tri-Axial Multi-Layered Nano-Particles, Jannatul Ferdaus

College of Graduate Studies: Theses & Dissertations

Electro-spraying has been used as an effective processing method of nanoparticle fabrication for the application of targeted drug delivery. The study demonstrates the feasibility of a non-conventional triaxial electro-spraying setup for multi-layered nano-drug fabrication and proposes optimized parameters. Two different drugs, XAV939 and Dextran 40000, were used to study the process parameters (voltage and solution concentration) of coaxial electro spraying. The particle size of Dextran-PCL was an average of 166.3 nm for PCL-Dextran at 32.5 kV and 18-hour sonication. The SEM analysis and UV-spectrum showed the encapsulation of Dextran with PCL, though the in vitro study in mice after 24 …

Identification Of Corrosion Damage, Vibration, And Loose Conections In Aircraft Data Transmission Lines Using Reflected And Transmitted Signals; Formulation Of Vegetable Oil-Based Nanofluids As Cutting Fluids For Mql Machining, Saidanvardzhon Valiev

Doctoral Dissertations

This research presents a novel Frequency Domain Transmitometry (FDT) method that uses transmitted signals (S21) to detect and characterize aircraft data transmission lines (ADTL) corrosion damage without additional reflectometry circuitry. Corrosion experiments were conducted according to ASTM G85-A5 over 14 weeks. Combined FDT and reflected signals (S11) analyses revealed distinct three-peak signatures associated with damage and corrosion. The square root of the Area Under the Curve (AUC) of the FDT damage peak and the Full Width at Three-Quarter Maximum (FW3QM) of the S11 damage peak is correlated with corrosion propagation depth and width. S11 signals were further used for vibration …

Process-Structure-Property Relationships In Laser Powder Bed Fusion Produced 17-4 Ph Steel, Ben Brown

Doctoral Dissertations

Laser powder bed fusion (LPBF) is a metal additive manufacturing method that produces non-traditional microstructures as a result of the rapid solidification and thermal cycling inherent to the process. When using LPBF-produced material in application, these unique microstructures challenge the applicability of well-developed mechanical property databases achieved by conventional heat treatments. For wider adoption of this technology, a more holistic understanding is necessary on how process attributes develop material structure, which dictate mechanical properties. This dissertation explores the process structure-property relationships in LPBF 17-4 PH steel through systematic evaluation of atmospheric processing and heat treatment effects on microstructure and mechanical …

Effect Of Build Orientation On Tensile Properties And Fractography Of Additive Manufactured Inconel 718 Alloy, Ajay Kumar Maurya, Amit Kumar, Swarnambuj Suman

ASEAN Journal on Science and Technology for Development

The additive manufacturing (AM) technique “Direct Metal Laser Sintering (DMLS)” is used to create 3D objects directly from 3D design data. A lightweight and complexity-free part without any expensive tooling can be fabricated easily using this method, but it is still challenging to achieve the desired mechanical strength from AM parts, as the mechanical properties of AM-produced parts vary with orientation, scan strategy, and process parameters. Inconel 718 alloy is most commonly utilized in the aerospace and automotive industries, because of its high resistance to corrosion and excellent mechanical qualities. This work presents a study to investigate the orientation-based mechanical …

Safety And Sustainability In The Domestic Ferry Sector : A Pci Framework For Esg-Aligned Maritime Governance, Mirza Zeeshan Baig

World Maritime University Ph.D. Dissertations

The domestic ferry sector is a significant component of maritime transportation. It strengthens social ties, supports economic growth and connects communities. Despites its importance, this industry faces ongoing challenges. These include fragmented governance, operational adequacies, safety risks and environmental concerns. The study deals with these issues by combining a systems-based approach with governance and change management theories. It examines the interplay between human, technical and organizational aspects. The study integrates the rule-based and rights-based maritime governance along with the Lewin’s three stage change management model (Unfreeze, Change, and Refreeze).

At the core of the study is the development of a …

Ioto: Never Open A Stiff Lid Again, Gabriel Portugal

Libraries Award for Undergraduate Scholarship

Background: From baby food to pickles, food jars are a common find in American homes. Unfortunately,  the task of opening a stiff jar lid can be very difficult for consumers with lower grip strength, parkinsons,  or arthritis. While there are a variety of products on the market to help make this easier, there exist few jar  openers that can be used by these consumers. Objective: This project aimed to research and develop  (R&D) an improved hands-free jar opener that is accessible for consumers with the most advanced  cases of limited arm strength. Methods: R&D followed a Design Thinking approach with …

Estimating Pedestrian Crossing Times At Scramble Crossings Via Machine Learning And Agent-Based Modeling, Sho Takami

CURE Proceedings

Scramble crosswalks differ from conventional crosswalks in their ability for pedestrians to cross diagonally. This research compares the average crossing times and investigates the walking behaviors that pedestrians adopt to produce the speediest times in the two crosswalk configurations. Identification of the most efficient set of walking behaviors is done through an agent-based model, whereas producing polynomials relating crossing times to the most prominent walking behaviors is done through regression algorithms in machine learning. With the combination of these two approaches, it is revealed that pedestrians must adopt a relaxed walking style to make each crosswalk configuration efficient. Additionally, between …