Engineering Commons^™

Preparation And Performance Of Carbon-Coated Si/C Composites, Li-Li Du, Quan-Chao Zhuang, Tao Wei, Yong-Li Cui, Zhi Sun, Shi-Gang Sun

Journal of Electrochemistry

Si/C composite for lithium ion batteries was obtained by pyrolyzing and ball-milling. The microstructure and component of the composite was characterized by SEM and XRD, the electrochemical performance was investigated by electrochemical impedance spectroscopy (EIS), cyclic voltammetry (CV) and galvano static charge-discharge tests. The results illustrate that the particle of Si/C composite prepared by pyrolysis exhibits inerratic morphology, uniform carbon-coating layer, good electrical conductivity, low resistance. The first intercalated-lithium capacity of the composite material is 4495 mAh/g; the first coulomb efficiency is 65.3%. From the second week the coulomb efficiency maintains 97%, and the capacity at the 100th cycle can …

The Flip-Flop Behavior Of Acetonitrile At Au Electrode Surface Investigated By Sum Frequency Generation Vibrational Spectroscopy, Zhi Huang, Xin Tang, Gang-Hua Deng, En-Cai Zhou, Hong-Fei Wang, Yuan Guo

Journal of Electrochemistry

The electrochemical interface between liquid acetonitrile and polycrystal gold electrode is investigated by in situ infrared visible sum frequency generation spectroscopy (SFG-VS). The structure of acetonitrile adsorbed at polycrystal gold electrode surface is studied as a function of electrode potential. The SFG spectra of CH₃ group indicate acetonitrile orients in response to the electrode potential. The SFG signal of CH₃ group turns lower as the electrode potential changes from -700mV to 300mV, and vanishes around the 300mV(pzc), then becomes a negative signal above 500mV, which indicates that the orientation is predominately with the CH₃ group toward the …

Research Progress In Orthosilicates As Cathode Materials For Li-Ion Batteries, Dong-Ping Lv, Lin Wang, Yong Yang

Journal of Electrochemistry

Rechargeable Li-ion batteries fulfilling high-energy density, high safety, environmental friendliness, and low cost are demanded urgently for energy storage systems. Besides the structure stability arising from the strong Si-O covalent bond, environmental benignancy and low cost from the characteristics of Fe, Mn, Si elementals, orthosilicates (Li₂MSiO₄) show promising prospect to meet the demand of high-energy density for its two available Li+ per formula unit. Motivated by these significant advantages, Li₂MSiO₄ have been intensively investigated in the past few years. In the present work, we gave a review on the progress of orthosilicate research …

Synthesis And Catalytic Property Of Flaked Spindle-Like Cuo Nanocrystals, Jian-Feng Fan, Li-Qing Li, Yu-Feng Huang, Lou-Zhen Fan

Journal of Electrochemistry

A simple and efficient electrochemical route was developed for the synthesis of flaked spindle-like CuO nanocrystals using aqueous electrolyte and Cu sacrificial anode (graphite as the cathode) in an undivided cell at a constant potential mode under room temperature. The morphologies, structure and component of CuO nanocrystals obtained were characterized by SEM, XRD, respectively. Flaked spindle-like CuO nanocrystals were successfully used to modify a GC electrode to detect H₂O₂ with cyclic voltammetry (CV) and amperometric (AC).The results showed that products were pure monoclinic CuO nanocrystals. The linear range for the determination of hydrogen peroxide is from 1.0 …

Detection Of Acute Promyelocytic Leukemia Pml/Rarî± Fusion Gene Using Graphene Modified Glassy Carbon Electrode, Zhi-Xian Lian, Guang-Xian Zhong, Kun Wang, Ai-Lin Liu, Xin-Hua Lin, Yuan-Zhong Chen

Journal of Electrochemistry

A graphene modified glassy carbon electrode (GCE) was prepared by electrochemical reduction of graphite oxide fixed on the surface of GCE. Then, the amino-group modified probe of acute promyelocytic leukemia (APL) PML/RARα fusion gene fragment was immobilized onto surface of the graphene modified GCE by coupling activating agent. With methylene blue (MB) as a novel electrochemical indicator, artificial APL PML/RARα fusion gene fragment was measured by differential pulse voltammetry (DPV). The result indicated graphene nanomaterial showed good sensitization on the signal of MB. The relationship between the reduction peak current of MB and the concentration of complementary strand was linear …

Influence Of Tert-Butylpyridine On The Band Energetics Of Nanostructured Tio2 Electrodes And The Photoelectrochemical Properties Of Dye-Seneitized Electrodes, Shu-Ming Yang, Ji-Chao Wang, Hui-Zhi Kou, Hong-Bin Xue, Hong-Jun Wang, Yu-Ling Guo

Journal of Electrochemistry

The flat band edges (Efb) of nanostructured TiO₂ electrodes in electrolyte solutions with tert-butylpyridine (TBP) of different concentrations have been determined with spectroelectrochemical technique. TBP played a role in band energetics of nanostructured TiO₂ electrodes. The Efb values of -2.25, -2.46 and -2.62 V were determined in three 0.2 mol•L^-1 tetrabutylammonium perchlorate (TBAP) acetonitrile electrolytes which contain 0, 0.2 and 0.4 mol•L^-1 TBP respectively. The addition of Li+ ions shifted Efb positively. The Efb values of -1.12, -1.22 and -1.30 V were determined in three 0.2 mol•L^-1 LiClO₄ acetonitrile electrolytes which contain 0, 0.2 …

Study On Direct Electro-Oxidation Of Anisaldehyde, Lin-Lin Wu, Ying-Hong Zhu, Shan-Shan Li, Hong-Yan Zeng, Chun-An Ma

Journal of Electrochemistry

The oxidation of anisole on Pt electrode was investigated by cyclic voltammery and constant potential electrolysis. The influence of scan rates, substrate concentration, supporting electrolytes and solvent were considered . The results show that the electro-oxidation process of anisole was irreversible. In this research the sulfuric acid was the best supporting electrolytes and acetone was the best solvent, and the process was controlled by diffusion . The product of constant potential electrolysis was charactered by GC-MS .The results show that the main products was anisaldehyde, and the selectivity was up to 66.5% when using acetone as solvent.

Effects Of Additives On The Electrochemical Behaviors Of Zn Electrode In Alkaline Solutions, Shu-Na Hong, Hai-Bin Lin, Zuo-Jian Su, He-Bing Zhou, Man Liang, Wei-Shan Li

Journal of Electrochemistry

Electrochemical behaviors of Zn in 3mol⋅L^-1 KOH solution containing the single additive(Pb(NO₃)₂, SDBS) the mixed additives(Pb(NO₃)²⁺SDBS) were investigated. The results showed that all the additives can supress the corrosion of zinc in 3mol•L_^-1 KOH solution. And the inhibition effeciency of the mixed additives is higher than that of any single additive.

Preparation And Electrocatalytic Activity Of The Pt/Wc/Tio2 Composites, Chun-An Ma, Bin Yu, Mei-Qin Shi, Xiao-Ling Lang

Journal of Electrochemistry

TiO₂ was used as the support for preparation of Pt/WC/TiO₂ composite catalyst. The composites were characterized by XRD, SEM and TEM methods. The electrocatalytical activity of Pt/WC/TiO₂ composite for oxidation of methanol was investigated by cyclic voltammetry. Pt/WC/TiO₂ exhibited higher activity compared with that of Pt/TiO₂ and Pt/WC composite catalysts. Based on this we discussed the effects of crystal phases of TiO₂ on the electrocatalytical activity of Pt/WC/TiO₂ composite catalyst.

Dft Study Of Co2 Reduction To Hydrocarbons On Cu Surfaces, Li-Hui Ou, Sheng-Li Chen

Journal of Electrochemistry

CO₂ reduction on Cu(111) single crystal surfaces was studied using DFT calculations on the reaction energies and the minimum energy paths. The results indicated that the possible reaction paths for CO₂ reduction on Cu(111) surface are CO₂(g) + H* → COOH* → (CO +OH)*, (CO + H)* → CHO*, CHO + H → CH₂O* → (CH_2⁺O)*, CH₂* + 2H* → CH₄ or 2CH₂* → C₂H₄. On Cu(111) surface, the reaction rate is controlled by steps of CH₂O* → (CH_{2 …}

Comparison Of Catalytic Performance On Different Materials Supported Pd Catalysts For Formic Acid Oxidation, Su-Dong Yang, Yan-Yu Liang, Zhu-Liang Wen, Qi-Jun Song, Xiao-Gang Zhang

Journal of Electrochemistry

Graphite oxide (GO) was prepared from by Hummers method. Then the graphene nanosheets supporting Pd catalysts were prepared by a single-step chemical reduction method. The electrocatalytic performance for formic acid oxidation of the prepared Pd/graphene composite was studied as an electrode material in comparison with the composite catalysts based on the other carbons (MWCNTs, SWCNTs, and Vulcan XC-72 carbon black). X-ray diffraction (XRD) and transmission electron microscopy (TEM) measurements indicated that the Pd nanoparticles were well dispersed on the surface of the graphene nanosheets with a small particle size. The electrocatalytic oxidation of formic acid was studied by electrochemically active …

Anode Electrodeposition Of Ti/Mno2 Electrode And Electrocatalytic Oxidization Properties Of Phenol Degradation, Ye Chen, Wen-Li Zhao, Qing Wen

Journal of Electrochemistry

Ti-base manganese dioxide (Ti/MnO₂) electrode was prepared by anodically electrodeposition technology in this paper. The structure of the electrode, the microstructure of the electrode surface and the element composition of the electrode were analyzed by XRD, SEM and EDS. The preparation process parameters of the electrode were studied in detail with the help of the V~logi curve and phenol degradation curve. The Ti/MnO₂ electrode was anodically electrodeposited at current density 4mA•cm^-2, the Mn^{2 +} ions concentration 0.5mol•L^-1 and temperature70℃. The V~logi curve and phenol degradation curve were used to evaluate electrocatalytic oxidization properties …

Electrochemical Capacitive Performance Of Mesoporous Carbon Based Co-Ni Oxides, Zhen-Sheng Yang, Ling-Bin Kong, Li Deng, Yong-Chun Luo, Long Kang

Journal of Electrochemistry

By using defects on the surface of CMK-3 served as nucleation center, Co_0.25Ni_0.75 oxide/C composite was successfully prepared through a simple chemical co-precipitation method. Characterization was carried by using X-ray diffraction, BET and scanning electron microscopy. Results showed that a perfect mesoporous network of interconnected nanoflakes was obtained for Co_0.25Ni_0.75 oxide/C composite and, this material has a less crystallization, interconnected nanoflakes network structure and a narrow mesoporous distribution at about 3~4 nm. The highly dispersed and loosely packed Co_0.25Ni_0.75 oxide/C composite possessed good electrochemical accessibility and fast diffusion rate of OH …

Capacitance Behaviors Of Ti/Ru0.1Ti0.1Sn0.8O2 Electrodes, Hai-Yan Chen, Yan-Qun Shao, Dian Tang

Journal of Electrochemistry

Ti/Ru_0.1Ti_0.1Sn_0.8O₂ electrodes were prepared by low temperature thermal decomposition. The structural characteristics were analyzed by X-ray diffraction(XRD).The performances were tested by cyclic voltammetry and constant current charge-discharge measurements. The results show that, the structure of Ti/Ru_0.1Ti_0.1Sn_0.8O₂ belongs to small rutile phase. A high specific capacitance of 933F/g is obtained at scan rate of 20 mV/s. The cycle life test shows a 23.6% specific capacitance lost after 1000 cycles. The electrode has a good cycle stability and reversibility.

Review Of The Maxus 8 Sounding Rocket Experiment To Investigate Solidification In A Ti-Al-Nb Alloy, Robin Mooney, David Browne, Olga Budenkova, Yves R. Fautrelle, Ludo Froyen, Andrey Kartavykh, Stephan Rex, Burkhard Schmitz, Daniella Voss, Shaun Mcfadden

Conference Papers

A review of the MAXUS 8 sounding rocket microgravity experiment to investigate solidification structures in a Ti-Al-Nb intermetallic alloy is presented. The experiment was part of the Intermetallic Materials Processing in Relation to Earth and Space Solidification (IMPRESS) EU FP6 project. Key objectives were to investigate columnar and equiaxed solidification, and to achieve Columnar-to-Equiaxed Transition (CET) in the alloy. A microgravity experiment was designed to achieve this using a controlled power-down method. Two alloys were tested: one inoculated with a grain refiner and the other without grain refinement. Unrefined samples displayed axial and radial columnar growth. Boride inoculated samples displayed …

Analysis Of A Monolithic Crystal Plate Acoustic Wave Filter, Huijing He

Department of Mechanical and Materials Engineering: Faculty Publications

We study thickness–shear and thickness–twist vibrations of a finite, monolithic, AT-cut quartz plate crystal filter with two pairs of electrodes. The equations of anisotropic elasticity are used with the omission of the small elastic constant c56 . An analytical solution is obtained using Fourier series from which the res-onant frequencies, mode shapes, and the vibration confinement due to the electrode inertia are calculated and examined.

Transverse Permeability Of Fibrous Porous Media, Ali Tamayol, Majid Bahrami

Department of Mechanical and Materials Engineering: Faculty Publications

In this study, the transverse permeability of fibrous porous media is studied both experimentally and theoretically. A scale analysis technique is employed for determining the transverse permeability of various fibrous matrices including square, staggered, and hexagonal arrangements of unidirectionally aligned fibers, as well as simple two-directional mats and simple cubic structures. In the present approach, the permeability is related to the porosity, fiber diameter, and tortuosity of the medium. In addition, the pressure drop in several samples of tube banks of different arrangements and metal foams are measured in the creeping flow regime. The pressure-drop results are then used to …

Improved Rehabilitation And Exercise Machine / Machine De Reeducation Et D'Exercice Amelioree, Judith M. Burnfield, Adam Taylor, Thad W. Buster, Carla A. Nelson, Yu Shu

Department of Mechanical and Materials Engineering: Faculty Publications

An improved rehabilitation and exercise machine is provided which allows a person with physical limitations, disabilities or chronic conditions to use the machine in order to rehabilitate their muscles, improve joint flexibility, and enhance cardiovascular fitness. An embodiment of the device includes a framework, a first and second crank arm, a first and second handle bar, a first and second foot pedal, a motor and pulley assembly, a first and second coupler link, and a motor controller with speed knob,

Ultrasonic And Stereo-Optical Characterization Techniques For Applications In Mechanical Testing, Jonathan M. Hein

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

This thesis considers methods developed based on ultrasonic reflections from interfaces and stereo-optical surface strain measurements to study the mechanical characterization of materials and bodies. The ultrasonic method is used to characterize wave speed and attenuation for highly attenuating samples. The stereo-optical strain measurements are used to characterize the effects of genes on mechanical properties of bone, and the dynamic characterization of blast waves in the UNL Shock Wave Trauma Mechanics facility.

A method is described and developed for characterizing the wave speed and attenuation spectrums from reflected waves from the contact surface with an unknown material. The method is …

Numerical Prediction Of The Haemodynamic Impact Of Coronary Stent Implantation, Jonathan Murphy

Doctoral

Arterial restenosis limits the effectiveness of coronary stenting. Restenosis is caused by excessive tissue growth which is stimulated by arterial injury and alterations to the arterial WSS. The altered WSS results from stent-induced disturbances to the natural haelnodynamics of the artery. Recent numerical studies have predcted only minor digerences in altered WSS between different stent designs using a commonly employed threshold assessment technique. While it is possible that there are only minor differences, it is more likely that the assessment technique is incapable of fully elucidating the altered WSS created by stent implantation. This thesis proposes a methodology that involves …

Tool Life Of Various Tool Materials When Friction Spot Welding Dp980 Steel, Christopher Shane Ridges

Theses and Dissertations

In this study, friction spot welding was used to join DP980 steel sheet. Four different ultra-hard tool materials were used with the objective of determining which tool material produced the highest number of acceptable-strength welds. Three of the tools were composed of various mixtures of polycrystalline cubic Boron Nitride (PCBN), Tungsten, and Rhenium. These materials are referred to herein as Q60, Q70, and Q80, the "Qxx" designation denoting the percentage of the volume of the tool material composed of PCBN. The fourth tool tested was composed entirely of PCBN. The Q70 tool produced approximately 1100 welds of acceptable strength before …

Material Reduction In Corrugated Containers For The Fresh Produce Industry, Justin Patterson

Industrial Technology and Packaging

In the fresh produce industry, corrugated containers must be made to provide adequate protection throughout the product life cycle. In response to increasing materials costs in the corrugated industry, companies are focusing upon developing more efficient packaging designs.  The scope of this project focuses on presenting alternative corrugated packaging designs for the fresh produce industry.  Included are one piece designs, three piece bliss designs and alternative material exploration.  This project presents the performance of new solutions by exploring their compressive strength before and after exposure to humidity.

Me-Em Enewsbrief, March 2011, Department Of Mechanical Engineering-Engineering Mechanics, Michigan Technological University

Department of Mechanical and Aerospace Engineering eNewsBrief

No abstract provided.

Waves In Microstructured Solids: A Unified Viewpoint Of Modelling, Arkadi Berezovski, Juri Engelbrecht, Mihhail Berezovski

Publications

The basic ideas for describing the dispersive wave motion in microstructured solids are discussed in the one-dimensional setting because then the differences between various microstructure models are clearly visible. An overview of models demonstrates a variety of approaches, but the consistent structure of the theory is best considered from the unified viewpoint of internal variables. It is shown that the unification of microstructure models can be achieved using the concept of dual internal variables.

Influence Of Electric Field On The Adsorption And Bioactivity Of Hemoglobin On A Macroporous Gold Electrode, Cui-Hong Wang, Yi-Bing Kong, Xing-Hua Xia

Journal of Electrochemistry

The adsorption and bioactivity of proteins at interfaces have been widely studied due to their important role in the construction of biosensors,bioelectronics and biofuel cells.Interfacial electric field is one of the important factors which could affect the adsorption and bioactivity of proteins at materials surfaces.It could dramatically change the adsorption density,molecular conformation and orientation at material surfaces.In this paper,the influence of interfacial electric field on the adsorption kinetics and bioactivity of hemoglobin(Hb) on a three-dimensional(3D) macroporous gold electrode surface has been studied using electrochemical methods and infrared spectroscopy.It was found that the interfacial electric field created excess surface charge which …

Prepartion And Characterization Of Spr Au Substrate Using Wet Chemical Plating, You-Chen Zhou, Yan-Yan Wang, Zhi-Fang Ma, Yan-Xia Jiang, Jin Qiu, Shi-Gang Sun

Journal of Electrochemistry

The present study developed a preparation method of SPR gold substrate based on water phase operation.Firstly,on the glass modified by APTMS we self-assembed a gold colloid monolayer as the catalyst bed;Secondly,using the chemical plating technique,we made the gold film increase equably within the namometer range to obtain the proper shape and thinkness of the gold film required by the SPR.The analysis results of UV-vis and TEM demonstrated that the diameter of the monolayer formed from gold nanoparticles was 2.5 nm.Moreover,SEM showed that the nanoparticle prepared by electroless gold plating was uniformly distributed,whose diameter was 40 nm.The SPR flow injection experiment …

Synthesis Of Mesoporous Nickel Oxide For Supercapacitor Application, Xuan-Xuan Chen, Zhen-Zhen Zhao, Deng-Chao Wang, Zhong-Jie Huang, Wen-Bin Ni, Li Yu, Jian-Wei Zhao

Journal of Electrochemistry

Mesoporous nickel oxide has been synthesized by calcining metal-organic coordination precursor.Transmission electron microscopy and BET test showed that the prepared NiO had a regular morphology and displayed a narrow size distribution.Electrochemical tests revealed that such mesoporous NiO had a specific capacity of 72 F·g^-1 at the current of 2.0 A·g^-1.Futhermore,the material showed excellent cycle-life stability.There was no degradation of capacitance after 1000 cycles.

A Titanium-Supported Nanoporous Pd Electrocatalyst For Methanol Oxidation, Feng-Juan Niu, Qing-Feng Yi

Journal of Electrochemistry

Titanium-supported nanoporous palladium electrode(nanoPd /Ti) was prepared by a hydrothermal process in the presence of the ligand EDTA and using formaldehyde as reducing agent.SEM images showed that the size of Pd particles was about 60 nm and the Pd particles were connected with each other to form a three-dimensional network structure.Cyclic voltammetry(CV) and electrochemical impedance spectroscopy(EIS) were applied to evaluate the electrocatalytic activity of the nanoPd/Ti electrode towards methanol oxidation in alkaline solution.CV results showed that the nanoPd /Ti electrode presented high anodic peak densities and a low onset potential for methanol oxidation.Also nanoPd /Ti electrode showed excellent CO tolerance …

Novel Anion Exchange Membranes Base On Copolymer Of 2-(Diethylamino) Ethyl Methacrylate And Fluoro-Polyacrylate For Alkaline Direct Methanol Fuel Cells, Yan-Mei Zhang, Jun Fang, Ge Yan, Yong-Ze Zhuang

Journal of Electrochemistry

Anion exchange membrane fuel cells,which use anion exchange membranes as polyelectrolytes,have attracted more and more research interests recently.In this work,a series of hydroxyl-conducting anion-exchange membranes based on the copolymer of 2-(Diethylamino)ethyl methacrylate and fluoro-polyacrylate were prepared by radical polymerization,and their potential applications in alkaline fuel cells were assessed.It was shown that the ionic conductivity of the membranes reached 10^-2 S·cm^-1 at room temperature,while the methanol permeability was lower than 10^-7 cm²·s^-1.The maximum power density of fuel cell assembled with this membrane was achieved to be 43.2 mW·cm^-2 at room temperature,indicating possible application …

Applications Of Raman Spectroscopy Technique In Lithium Ion Batteries, Liang Zhao, Yong-Sheng Hu, Hong Li, Zhao-Xiang Wang, Hong-Xing Xu, Xue-Jie Huang, Li-Quan Chen

Journal of Electrochemistry

The Raman spectroscopy has been widely used in the study of lithium ion batteries.In this short review,we gave some examples of the applications of Raman spectroscopy in the study of electrode materials including carbonaceous materials,spinel LiM_xMn_2-x O₄,LiFePO₄,as well as polymer electrolytes,room temperaturemolten salt electrolytes and the solid-electrolyte interphase layers.The advantages and disadvantages of the ex-situ and in-situ Raman spectrum techniques are discussed.Using new Raman techniques to investigate Li-ion batteries are suggested.