Engineering Commons^™

Feasibility Analysis Of Estrification Systems With Entrainers, Kang Wook Lee

Dissertations and Theses

(Ethyl Acetate) and IPA (Isopropyl Acetate) production systems are studied in terms of the feasibility analysis. It is not feasible to retrieve pure products by a simple reactive distillation for IPA production system because CCR (Critical Composition Region) covers the entire desired binary edge for IPA system. On the other hand, even though CCR does not cover the entire desired binary edge of the EA system completely, internal reflux ratio (IRR) analysis does not allow the production of the pure product via reactive distillation for EA production system. To overcome the restraints, external entrainers are utilized to take advantage of …

Microwave-Assisted Wet Chemical (Mawc) Synthesis Of Lithium Iron Phosphate, Shangzhao Shi

Dissertations, Master's Theses and Master's Reports - Open

LiFePO4 is a Co-free battery material. Its advantages of low cost, non-toxic and flat discharge plateau show promising for vehicle propulsion applications. A major problem associated with this material is its low electrical conductivity. Use of nanosized LiFePO4 coated with carbon is considered a solution because the nanosized particles have much shorter path for L+ ions to travel from the LiFePO4 crystal lattice to electrolytes. As other nano material powders, however, nano LiFePO4 could have processing and health issues.

In order to achieve high electrical conductivity while maintaining a satisfactory manufacturability, the particles should possess both of the nano- and …

Finite Element Analysis Of The Contact Deformation Of Piezoelectric Materials, Ming Liu

Theses and Dissertations--Chemical and Materials Engineering

Piezoelectric materials in the forms of both bulk and thin-film have been widely used as actuators and sensors due to their electromechanical coupling. The characterization of piezoelectric materials plays an important role in determining device performance and reliability. Instrumented indentation is a promising method for probing mechanical as well as electrical properties of piezoelectric materials.

The use of instrumented indentation to characterize the properties of piezoelectric materials requires analytical relations. Finite element methods are used to analyze the indentation of piezoelectric materials under different mechanical and electrical boundary conditions.

For indentation of a piezoelectric half space, a three-dimensional finite element …

Optical Detection Of Melting Point Depression For Silver Nanoparticles Via In Situ Real Time Spectroscopic Ellipsometry, S. A. Little, T. Begou, R. W. Collins, S. Marsillac

Electrical & Computer Engineering Faculty Publications

Silver nanoparticle films were deposited by sputtering at room temperature and were annealed while monitoring by real time spectroscopic ellipsometry (SE). The nanoparticle dielectric functions (0.75 eV-6.5 eV) obtained by SE were modeled using Lorentz and generalized oscillators for the nanoparticle plasmon polariton (NPP) and interband transitions, respectively. The nanoparticle melting point could be identified from variations in the oscillator parameters during annealing, and this identification was further confirmed after cooling through significant, irreversible changes in these parameters relative to the as-deposited film. The variation in melting point with physical thickness, and thus average nanoparticle diameter, as measured by SE …

Improving Discourse Structure Identification, Jamie Allison Guidry

LSU Master's Theses

Rhetorical Structure Theory (Mann et al. 1988), a popular approach for analyzing discourse coherence, suggests that coherent text can be placed into a hierarchical organization of clauses. Identification of a text’s rhetorical structure through automatic discourse analysis is a crucial element for many of today’s Natural Language Processing tasks, but no sufficient tool is available. The current state-of -the-art discourse parser, SPADE (Soricut et al. 2003), is limited to parsing discourse within a single sentence. HILDA (Hernault et al. 2010) extends the parsing abilities of SPADE to the document level, but with a decrease in performance. This study achieved document-level …

Investigation Of Gallium Nitride Transistor Reliability Through Accelerated Life Testing And Modeling, Bradley D. Christiansen

Theses and Dissertations

Gallium nitride high electron mobility transistors are attractive to the DoD for their ability to operate at high frequencies, voltages, temperatures, and power. Yet, there are concerns about the reliability of these devices. Various degradation mechanisms and their causes are proposed in the literature. A variety of reliability tests were conducted to understand these mechanisms and causes. A multi-stressor experiment revealed different failure mechanisms than are in the literature. In particular, the devices tested at high voltage in the OFF state did not degrade significantly as suggested by others' reports. The validity of temperature-accelerated life testing when applied to GaN …

Generic Strategies To Implement Material Grading In Finite Element Methods For Isotropic And Anisotropic Materials, Ke Yu

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

We look at generic strategies to transfer material grading into finite element methods. Three strategies are proposed to transfer material grading into the finite element analysis. These strategies are node-centered, element-centered, and the definition of material grading through external functions. The process to achieve each strategy is stated, and examples are used to illustrate each strategy, and to compare them. The strategies are implemented in finite-deformation nonlinear elastic analysis.

Several examples are used to illustrate the implementation of each strategy for graded isotropic materials. For these examples, the results obtained from finite element models are compared with those obtained from …

Nanozeolites Doped Photopolymer Layers With Reduced Shrinkage, Mohesh Moothanchery, Izabela Naydenova, Svetlana Mintova, Vincent Toal

Articles

An acrylamide based photopolymer doped with pure silica MFI-type zeolite (silicalite-1) nanoparticles has been characterized for holographic recording purposes. The concentrations of the silicalite-1 nanoparticles in the photopolymer layers were 1, 2.5, 5 and 7.5 wt.%. The inclusion of silicalite-1 nanoparticle in the photopolymer has resulted in an increase of the diffraction efficiency by up to 40%, and decrease of the shrinkage from 1.32% to 0.57%. The best results were obtained in layers doped with 5 wt.% silicalite-1 nanoparticles.

Development Of A Structured Concrete Thermocline Thermal Energy Storage System, Bradley M. Brown

Graduate Theses and Dissertations

The past couple of decades have shown a concern when considering the way the world obtains its power. The focus has been switching from fossil fuels that have been used for hundreds of years to renewable energy sources, such as the sun. Solar energy is readily and infinitely available for harnessing. One problem with solar energy, though, is its inability to be used during the night time and during cloud covered weather. A solution to this problem is the use of energy storage mechanisms. For solar plants that use solar thermal energy (concentrating solar power plants), thermal energy storage (TES) …

Me-Em Enewsbrief, December 2011, Department Of Mechanical Engineering-Engineering Mechanics, Michigan Technological University

Department of Mechanical and Aerospace Engineering eNewsBrief

No abstract provided.

The Effects Of Solvent Mixture On The Thermal And Mechanical Properties Of Solvent Cast Poly-Lactic Acid (Pla) Film, Jeremy Hughes

All Theses

CH 1 ABSTRACT
The objective of this study was to investigate the effects of various solvents on the crystallinity and thermal expansion stability of PLA film. Three different PLA films were produced by the solvent casting technique; PLA in chloroform (PLA-C), PLA in methylene chloride (PLA-M), and PLA in methylene chloride: acetonitrile = 50: 50 (PLA-MA). The PLA-MA had higher % crystallinity, 46.15, than the PLA-C, 24.03, and the PLA-M, 14.25. With this increase in crystallinity, the PLA-MA had improved thermal expansion stability as shown by very low accumulated dimensional changes at 20-100 ¡C. Wide angle x-ray diffraction identified multiple …

In-Situ Ellipsometry Characterization Of Anodically Grown Silicon Dioxide And Lithium Intercalation Into Silicon, Eric A. Montgomery

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

In this thesis, in-situ ellipsometry and electroanalytical investigations of two electrochemical processes are reported: including the formation of anodically grown silicon dioxide and the intercalation of lithium into silicon. Analysis of the ellipsometry data shows that the anodically grown silicon dioxide layer is uniform and has similar properties as thermally grown silicon dioxide. The lithium-ion intercalation data reveals non-uniform thin film formation, which requires further studies and development of appropriate ellipsometric optical models.

Advisers: Eva Schubert and Mathias Schubert

Preparation And Application Of Nano-Nio As Anode In Lithium-Ion Batteries, Cheng-Dong Bai, Jia-Jia Chen, Qi Zhang, Ming-Sen Zheng, Quan-Feng Dong

Journal of Electrochemistry

In this work, the nano-NiO material was prepared by hydrothermal method. The surface morphologies and electrochemical properties of nano-NiO material were investigated. The special nano-NiO material with porous surface assembling honeycombs(100-200nm) was obtained by using surface active agents. The discharge capacity of nano-NiO electrode up to 2385.7 mAh/g was achieved at current density of 0.1A/g in the first circle,while 1100mAh/g could be maintained after 100 circles. At current density of 2.0A/g, the discharge capacity of 600 mAh/g was obtained. And when the current density was reduced to 0.1A/g, the discharge capacity was restored to 1050 mAh/g. The nano-NiO electrode exhibited …

Corrosion Behaviors Of 316 Stainless Steel Weldment Studied By Array Reference Electrodes, Wang-Huo Yang, Rong-Gang Hu, Chen-Qing Ye, Wei Hang, Ning Li, Chang-Jian Lin

Journal of Electrochemistry

The array reference electrodes were developed to in situ measure the potential distributions of the welded 316 stainless steel in 12% FeCl3 solution, combined with metallographic analysis, polarization curve, EIS measurement and Kelvin volta potential imaging. It was indicated that the weld zone of metal suffered a serious preferential corrosion when immersed in the environment due to the distinct changes of structure and composition during the welding process. With time prolonging, the corrosion potential of the welding zone was negatively shifted to a maximum value, and then declined gradually. At 45 min immersion, the corrosion development from welding zone to …

Microemulsion Preparation And Electrochemical Characterization Of Pt/C, Ptir/C Electrocatalysts, Ya-Ping Zeng, Sheng Sui

Journal of Electrochemistry

The Pt/C electrocatalysts were prepared by three different systems and the PtIr/C electrocatalysts were prepared with four different Ir contents. The samples were characterized by X-ray diffraction (XRD), transmission electron microscope (TEM), cyclic voltammetry (CV), potentiostatic and potentiodynamic polarizations measurements. The experimental results confirmed that the electrocatalyst particles prepared by the microemulsion method were well distributed on XC-72R supports with the active particle sizes of 5～10nm and good electrocatalysts activity. The Pt85Ir15/C electrocatalysts showed the highest overall electrochemical activity in unitized regenerative fuel cell.

Preparation And Characterization Of Casno3 Anode Material For Lithium Ion Batteries, Ran Sun, Zi-Geng Liu, Ya-Qi Jiang

Journal of Electrochemistry

In this study the precursor CaSn(OH)₆ was prepared via a hydrothermal process, and its composition, surface feature and phase-transition were characterized by XRD, SEM and DSC-TGA. The shapes of CaSn(OH)₆ crystals were effectively controlled by adjusting the volumn ratio of H₂O and CH₃CH₂OH solvents. Perovskite CaSnO₃ could be obtained by calcination of CaSn(OH)₆ at 800 ℃. The reversible capacity of 334.4 mAh/g with good cycling stability could be achieved with the CaSnO₃ electrode.

Preparation And Characterization Of The Lani0.6Fe0.4O3-δ Cathode For Intermediate Temperature Solid Oxide Fuel Cell, Hang Liu, Bo Huang, Xin-Jian Zhu

Journal of Electrochemistry

The LaNi_0.6Fe_0.4O_3-δ as cathode material for intermediate temperature solid oxide fuel cell was prepared using a combustion synthesis technique. The X-ray diffraction (XRD) pattern showed that the single-phase LaNi_0.6Fe_0.4O_3-δ perovskite could be obtained after heat treatment at 600°C. The TEM and SEM images of the synthesized powders revealed that the grains were 50-100nm. According to the electrochemical impedance spectra (EIS), the polarization resistance of the symmetric cell LaNi_0.6Fe_0.4O_3-δ/ScSZ/LaNi_0.6Fe_0.4O_3-δ sintered at 1050°C was the smallest (0.70Ω·cm², 0.27Ω·cm^{2 …}

Preparation And Application Of Macroporous Ato/Sio2 Electrode In Electrochemical Degradation Of 4-Chlorophenol, Zhang-Lin Chai, Rui-Feng Zhang, Tong-Hu Xiao, Yun-Xiao Liang

Journal of Electrochemistry

The macroporous ATO/SiO₂ materials were prepared through multiple steps of hydrolysis deposition in ethylene glycol and acetonitrile mixed solutions of SnCl₂/SbCl₃ and subsequent calcination at high temperature. The structures of the obtained materials were characterized by means of SEM and XRD. The results showed that the nano-ATO chemically deposited on the SiO₂ support underwent well-controlled aggregation and recrystallization to form a sandwich structure (ATO-SiO₂-ATO). Through four times loading of ATO the volume resistivity and the specific surface area reached 10·cm and 77 m²·g^-1, respectively. The oxygen evolution potential on …

Dynamic Modeling And Characteristic Analysis Of Proton Exchange Membrane Fuel Cell, Qiu-Hong Jia, Ming Han, Bin Deng, Cai-Zhi Zhang

Journal of Electrochemistry

In this paper, a dynamic model of PEMFC is developed to estimate the dynamic performance of PEMFC by analyzing in detail the influence factors of voltage of PEMFC including various losses. The partial pressure of hydrogen and oxygen is obtained using the differential form of the ideal-gas equation in this model. The steady-state model is obtained by setting reasonable parameter values. The simulation results and experimental results have good consistency, which shows that the simulation model is correct, reasonable and effective. It analyzed the dynamic response characteristics of the output voltage and the partial pressure of hydrogen in condition of …

Preparation And Capacitance Characteristics Of Nickel Oxide Electrode With Mesh-Like Structure, Hui Xu, Zhen-Jun Peng, Dong-Hong Guo, Jun-Ling Li

Journal of Electrochemistry

The mesh-like structure of NiO electrode was obtained by first preparing the precursors via hydrothermal process using nickel sulfate and carbamide as reactants, sodium hexametaphosphate as a surfactant, and followed by calcination of the precursors at 400 ℃. The structure, morphology and capacitance characteristics of NiO electrode were characterized by XRD, SEM and constant current charge-discharge testing techniques. The effects of hydrothermal temperatures on the electrochemical properties of NiO electrode were investigated. The results showed that the better property of nickel oxide was obtained when the mole ratio of nickel to urea was 1:4 and the hydrothermal temperature was 140℃. …

A Brief Review Of Research Progress In The Development Of Engineering Models For Lithium Ion Batteries, Da-Wei Wang, Dong-Jiang Li, Jun Li, Yong Yang

Journal of Electrochemistry

Lithium ion battery has become an important and popular electrochemical device for energy storage.Suitable evaluation and understanding of electrochemical performance and state of charge play a key role in the applications of lithium ion batteries.Construction and utilization of engineering modeling for lithium ion batteries is an effective way to fulfill this target.In this paper,engineering models of lithium ion batteries based on electrochemical reaction,ionic diffusion and migration are introduced.The emphasis is placed on the development of engineering models by the introduction of side reaction,phase transition,stress and energy.The applications of engineering models in such simulations as charge-discharge,concentration distribution,current distribution,state of charge,stress and …

Brief Introduction Of Organic Electrochemistry, Huan Wang, Jia-Xing Lu

Journal of Electrochemistry

Organic electrochemistry is a very useful tool for organic synthesis, not only because of the selective introduction or removal of electrons from organic molecules, but also for its green process. In this paper, electroorganic synthesis has been introduced from the systems, research methods and technologies to the characterization. Most of organic compounds could be electrochemically oxidized or reduced. Here, taking C=C compounds as an example, several kinds of electrochemical organic synthesis reactions are discussed, such as electrochemical addition, electrocatalytic dimrization, electropolymerization, etc. Electroorganic synthesis has been industrialized since 1960s. In this paper, electrosynthesis of adiponitrile was used as an example …

Electrocatalytic Determination Of 15 Kinds Of Phenolic Compounds By Novel Gold Nanoparticles-Modified Glassy Carbon Electrode, Yan-Ping Cui, Wei-Xing Wang, Chang-Zhu Yang, Wen-Hong Pu

Journal of Electrochemistry

A gold nanoparticles modified glassy carbon electrode (Au/GCE) was used to detect 15 kinds of phenolic compounds. In the cyclic voltammetry measurements, the peak currents of phenolic compounds at Au/GCE were all increased as compared with GCE and planar gold electrodes, and the oxidation potentials were determined by the activity of analytes. Besides, electrocatalysis of salicylic acid was studied at Au/GCE. The results showed that, there was a good linear relationship between the oxidation current and the concentration of salicylic acid, and the current sensitivity was 1.8 fold higher than that obtained on GCE. Trace phenolic compounds determination could be …

Electrochemical Properties Of Tungstogermanate And Electrocatalysis Of H2O2 On Gew11Co/P-Opd/Gc Electrode, Li-Li Zhu, Jian-Ying Qu, Jue Wang, Hao-Yue Feng

Journal of Electrochemistry

The electrochemical properties of Co-substituted trimeric tungstogermanate containing Keggin fragments were studied. Cyclic voltammograms revealed two couples of reversible redox peaks on glassy carbon (GC) electrode in acid solutions. They corresponded to two-electron reductions accompanying by the additions of four protons and three protons, respectively, both were controlled by adsorption. The differences in the peak potentials of 2-electron-4-proton and 2-electron-3-proton reactions were 31 mV and 35 mV, respectively..Furthermore, the tungstogermanate (GeW11Co) modified GC electrode with functionalization by poly(o-phenylenediamine) (P-oPD) was prepared readily by electropolymerization. The GeW11Co/P-oPD/GC electrode could electrocatalyze the reduction of hydrogen peroxide, which showed good stability and quick …

Indirect Electrochemical Reduction And Cotton Dyeing Process In Fe(Ⅲ)-Oxalate-Calcium Gluconate System, Qing-Zhi Wang, Wei Wang

Journal of Electrochemistry

The electrochemical behavior and possible reaction mechanism in Fe(Ⅲ)-oxalate-calcium gluconate system were studied by cyclic voltammetry. The results showed that Fe(Ⅱ)-gluconate was the final reductant. The reduction time, the working voltage and the cathode area influenced the current efficiency. The high current efficiency of 89% for the indirect electrochemical reduction of Vat Scarlet R could be achieved with reduction time of 10 min, working voltage of 4 V and cathode area of 40 cm² in Fe(Ⅲ)-oxalate-calcium gluconate system.

Electrochemical Behaviors Of Hydroquinone On Polypyrrole/Stab-Nammt/Gc Electrode, Rong Li, Jian Xiong, Wei-Qiong Zhu, Yuan-Yuan Han, Jin Xu, Xiao-Ying He

Journal of Electrochemistry

The PPy/STAB-MMT/GC electrode was made using montmorillonite modified by STAB and polypyrrole (PPy). The electrochemical behaviors of hydroquinone on the PPy/STAB-MMT/GC electrode were researched by cyclic voltammetry and square wave stripping voltammetry (SWSV). The results showed that the electrode reaction occurred on the hydroquinone electrode was controlled by diffusion in PBS (pH=6.0). The number of electron transfer was equal to the number of protons (n=m=1) with the effective area of PPy/STAB-MMT/GC electrode Aeff=0.031 cm². Under the optimized conditions, the linear response of peak current in SWSV with the concentration of hydroquinone in a range of 8.0×10^-6~8.0×10 …

Dc Pulsed Atmospheric Pressure Plasma Jet Image Information, Denis P. Dowling, F T. O'Neill, Vladimir Milosavljevic, Victor J. Law

Articles

This paper presents optical imaging and optical emission spectroscopy (OES) data of an atmospheric-pressure plasma jet. It is shown how the visual information and OES information of the air discharge are related as the blown arc extends from the nozzle (2-4 mm) with a molecular nitrogen rotational temperature on the order of 1700 K and the flowing afterglow beyond this region is dominated by the cooler (300-K) NO-O chemiluminescent reaction that produces NO₂ species.

Thickness-Shear And Thickness-Twist Vibrations Of An At-Cut Quartz Mesa Resonator, Huijing He, Jinxi Liu, Jiashi Yang

Department of Mechanical and Materials Engineering: Faculty Publications

We study thickness-shear and thickness-twist vibrations of an AT-cut quartz plate mesa resonator with stepped thickness. The equations of anisotropic elasticity are used with the omission of the small elastic constant c56. An analytical solution is obtained using Fourier series from which the resonant frequencies, mode shapes, and energy trapping are calculated and examined. The solution shows that a mesa resonator exhibits strong energy trapping of thickness-shear and thickness-twist modes, and that the trapping is sensitive to some of the structural parameters of the resonator.

In Vivo Three-Dimensional Blood Velocity Profile Shapes In The Human Common, Internal, And External Carotid Arteries, Alexey Kamenskiy, Yuris A. Dzenis, Jason N. Mactaggart, Anastasia Desyatova, Iraklis I. Pipinos

Department of Mechanical and Materials Engineering: Faculty Publications

Objective: True understanding of carotid bifurcation pathophysiology requires a detailed knowledge of the hemodynamic conditions within the arteries. Data on carotid artery hemodynamics are usually based on simplified, computer-based, or in vitro experimental models, most of which assume that the velocity profiles are axially symmetric away from the carotid bulb. Modeling accuracy and, more importantly, our understanding of the pathophysiology of carotid bifurcation disease could be considerably improved by more precise knowledge of the in vivo flow properties within the human carotid artery. The purpose of this work was to determine the three-dimensional pulsatile velocity profiles of human carotid arteries. …

Me-Em Enewsbrief, September 2011, Department Of Mechanical Engineering-Engineering Mechanics, Michigan Technological University

Department of Mechanical and Aerospace Engineering eNewsBrief

No abstract provided.