Engineering Commons^™

Poly(Aniline/O-Nitroaniline): A High Capacity Cathode Material For Lithium Ion Batteries, Rui-Rui Zhao, Li-Min Zhu, Jiang-Feng Qian, Han-Xi Yang

Journal of Electrochemistry

Polyaniline can be used as a high capacity cathode material due to the advantages of material abundance and synthetic simplicity. However, its practical application in battery has been hindered by poor electrochemical utilization and cycling instability. To solve these problems, we synthesized the poly(aniline/o-Nitroaniline) (P(AN-oNA)) by introducing the electron-drawing group-nitroaniline onto the polyaniline chains, so as to enhance electrochemical utilization and stability of the polyaniline derivative. The as-prepared Li/P(AN-oNA) copolymer shows a greatly enhanced discharge capacities of 186 mAh·g^-1 at initial cycles, about 37% higher than its parent PAN, and remains 168 mAh·g^-1 after 60th cycle. Also, the …

Synthesis And Electrochemical Characterization Of Li3V2(Po4)3/C Cathode Material By Ball-Milling Assisted Microwave Method, Zhi-Yuan Tang, Wen-Feng Mao, Ji Yan, Wei Yuan, Xin-He Zhang

Journal of Electrochemistry

The cathode materials of Li₃V₂(PO₄)₃/C were successfully synthesized by ball-milling assisted microwave method and the microwave irradiation time was also optimized. It is found that the Li₃V₂(PO₄)₃/C material obtained at a microwave power of 640 W for 18 min showed the best electrochemical performance with the initial reversible capacity of 101.3 mAh·g^-1 and the remained 100.8 mAh·g^-1 at 5C rate after 300 cycles. This excellent electrochemical capability may be resulted from good crystallinity, smaller and uniform particle size of the material, showing …

Electrochemical Performance Of Yf3-Coated Li(Li0.22Ni0.17Mn0.61)O2 Cathode Material For Li-Ion Batteries, Xin Feng, Guo-Ran Li, Shi-Hai Ye, Xue-Ping Gao

Journal of Electrochemistry

The Li(Li_0.22Ni_0.17Mn_0.61)O₂ was prepared with oxalic co-precipitation and coated with an YF₃ layer by a chemical deposition method. The as-prepared and YF₃-coated Li-rich materials were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDS). The results demonstrate that the as-prepared and YF₃-coated Li(Li_0.22Ni_0.17Mn_0.61)O₂ materials have a typical layered structure and are composed of sphere-like particles with a diameter of 100~200 nm. Galvanostatic charge-discharge tests show that the discharge capacity of the YF₃-coated Li(Li_{0.22 …}

Preparation And Modification Of Li4Ti5O12 As Anode Materials For Lithium-Ion Batteries, Jin-Long Liu, Zhou-Guang Lu, Yang Ren, Ya-Jie Zhu, Shan-Shan Hu, Zhong Peng, Dong Qian, You-Gen Tang

Journal of Electrochemistry

Anode Material Li₄Ti₅O₁₂ for lithium-ion batteries was successfully prepared using half-solid-state method. Furthermore, carbon coating modification of Li₄Ti₅O₁₂ was also carried out. The phase structure and morphology were analyzed by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and high resolution transmission electron microscopy (HRTEM). The electrochemical properties were investigated by constant current discharge-charge tests, cyclic voltammetry and electrochemical impedance techniques. The results indicated that the electrochemical performance of Li₄Ti₅O₁₂ without modification declined seriously due to the aggregation of Li₄Ti …

Electrochemical Sensing Of Guanine And Adenine Based On The Boron-Doped Carbon Nanotubes Modified Electrode, Ya-Lin Xia, Chun-Yan Deng, Juan Xiang

Journal of Electrochemistry

In this work, the boron-doped carbon nanotubes (BCNTs) modified glassy carbon (GC) electrode was simply fabricated, and the electrochemical oxidation behaviors of guanine and adenine at the BCNTs/GC electrode were investigated. Compared with the bare GC and CNTs/GC electrodes, the BCNTs-modified electrode exhibited extraordinary electrocatalytic activity towards the oxidations of guanine and adenine as indicated by the obvious increase in current responses. Moreover, the peak separation between guanine and adenine was large enough for their potential recognition in mixture without any separation or pretreatment. Therefore, the simultaneous determination of guanine and adenine was successfully achieved. The BCNTs/GC electrode showed high …

Friction Stir Spot Welding Of Ultra-High Strength Steel, Trent J. Hartman

Theses and Dissertations

Friction stir spot welding (FSSW) is quickly becoming a method of interest for welding of high strength steel (HSS) and ultra high strength steel (UHSS). FSSW has been shown to produce high quality welds in these materials, without the drawbacks associated with fusion welding. Tool grade for polycrystalline cubic boron nitride (PCBN) tools has a significant impact on wear resistance, weld quality, and tool failure in FSSW of DP 980 steel sheet. More specifically, for a nominal composition of 90% CBN, the grain size has a significant impact on the wear resistance of the tool. A-type tools performed the best, …

Selective Laser Sintering; A Design Of Experiments, Philip David Hopkins, Victor Castillo Phd

STAR Program Research Presentations

Additive Manufacturing (AM), also commonly known as 3D Printing or Rapid Prototyping, is a method of manufacturing that provides for the ability to make intricate internal features and easily customizable parts. The concept is to break a Computer Aided Design (CAD) file into a series of thin layers that are sent to the machine and laid down one layer at a time. Just like any other form of processing, material properties can alter by undergoing this process. Manipulating various parameters of the AM process can allow for different properties to be achieved. For this reason, an in depth study will …

Determining The Proper Point Size For Display Type On Packaging, Joanna Fischer

All Theses

Through the use of a preference test, the proper point size of display text on a package was evaluated in relation to a package's proportions. The test involved the examination of packaging images displaying the product or brand name in various point sizes by 150 participants who were then asked to choose the option they most preferred. The participants were then provided with a post-survey intended to gather additional information regarding potential preference motives.
The primary purpose of this study was to determine the most preferred display type size of a package based on its relationship with the package's proportions. …

A Resistance Based Structural Health Monitoring System For Composite Structure Applications, Dennis N. Boettcher

Master's Theses

This research effort explored the possibility of using interwoven conductive and nonconductive fibers in a composite laminate for structural health monitoring (SHM). Traditional SHM systems utilize fiber optics, piezoelectrics, or detect defects by nondestructive test methods by use of sonar graphs or x-rays. However, these approaches are often expensive, time consuming and complicated.

The primary objective of this research was to apply a resistance based method of structural health monitoring to a composite structure to determine structural integrity and presence of defects.

The conductive properties of fiber such as carbon, copper, or constantan - a copper-nickel alloy - can be …

Shear-Horizontal Vibration Modes Of An Oblate Elliptical Cylinder And Energy Trapping In Contoured Acoustic Wave Resonators, Huijing He, Jiashi Yang, John A. Kosinski

Department of Mechanical and Materials Engineering: Faculty Publications

We study shear-horizontal free vibrations of an elastic cylinder with an oblate elliptical cross section and a traction-free surface. Exact vibration modes and frequencies are obtained. The results show the existence of thickness-shear and thickness-twist modes. The energy-trapping behavior of these modes is examined. Trapped modes are found wherein the vibration energy is largely confined to the central portion of the cross section and little vibration energy is found at the edges. It is also shown that face-shear modes are not allowed in such a cylinder. The results are useful for the understanding of the energy trapping phenomenon in contoured …

Dynamical Properties Of Ferroelectric Perovskites (Ba,Sr)Tio3 And Pb(Zr,Ti)O3 Systems From First Principles, Jeevaka Weerasinghe

Graduate Theses and Dissertations

A first-principles-based effective Hamiltonian scheme which incorporates coupling between ferroelectric (FE) and antiferrodistortive (AFD) motions is applied to Pb(Zr,Ti)O₃ alloys. It validates the existence of two modes of E symmetry (rather than the single E(1TO) soft mode) in the 50-75 cm^-1 range for temperatures smaller than 200 K and for compositions falling within the Rhombohedral R3c phase. Coupling between long-range-ordered FE and AFD motions is shown to be the cause of the additional mode and more insight into its nature is provided. This scheme is further used to reveal a field-induced anticrossing involving FE and AFD degrees of …

Development And Characterization Of Shellac-Hydroxypropyl Methyl Cellulose Composite Films With Acid Catalyst, Sana Asrar

All Theses

The objective of this research was to develop a shellac-hydroproyl methyl cellulose (Sh-HPMC) composite film with enhanced water vapor barrier. Citric acid (CA) was used as an acid catalyst, to promote miscibility between HPMC and shellac. In a preliminary test, three different concentrations of CA (1000:1, 200:1, 100:1) were tested to identify the best Sh:CA ratio. Based on the Water vapor permeability properties and mechanical properties, Sh-CA (1000:1 ratio) had the most enhanced water vapor barrier and the lowest reduction in tensile strength compared to the pure HPMC film (control). In the later part of the research, the effect of …

The Effect Of Food Ingredients On The Oxygen Barrier Properties Of Retort Materials, Amanda Ward

All Theses

An unexplored area in research is addressing how retorted food ingredients interact with retort packaging's oxygen barrier. Ten common food ingredients (whey protein isolate, soy protein isolate, bovine gelatin, fish gelatin, high molecular weight fish gelatin, water, air, oil, potato starch, and hydroxypropyl methylcellulose) were assessed to find their effect on the barrier properties of CPP, PET, and high barrier commercial retort pouches. OxySense Gen III 300 and Mocon OxTran 2/21 were used to evaluate the samples. CPP pouches were first assessed with the OxTran 2/21 and indicated that treatments affected the OTR's of the film materials. However, results from …

Relating Burst Pressure To Seal Peel Strength In Pouches, William Bernal

All Theses

This work was aimed at studying the relationship between burst pressure and seal peel strength. Past researchers developed a force balance equation based on the analysis of a force diagram to relate burst pressure to seal strength. The theoretical formula S=P(D/2) (S=Seal Strength, P=Burst Pressure, D=Restraining Plate Gap) has been studied by past researchers with contrasting results.
The theoretical formula was tested by varying dwell time to produce seals of varying strength. Pouches were burst tested at each of these dwell times to obtain burst pressures, burst peeling times, and burst locations. Corresponding peel tests were performed with crosshead speeds …

Efficient Airframe Management Using In-Situ Structural Health Monitoring, Mark M. Derriso, M. S. Leonard, Martin P. Desimio, Steven E. Olson

Student Publications

The United States Air Force utilizes the Aircraft Structural Integrity Program (ASIP) to service and maintain its airframes. This schedule-based maintenance approach works well for ensuring system integrity; however, it is very costly, labor-intensive, and it reduces system availability. As a result, the Air Force intends to transition to a process that services aircraft based on their actual condition instead of the presumptive schedule-based approach. Structural health monitoring (SHM) technologies are being investigated to enable such real-time state awareness and decision-making. This paper provides a brief review of ASIP and the required inspections to investigate structural fatigue. The current ASIP …

Propagation Of Ultrasound Through Freshly Excised Human Calvarium, Armando Garcia Noguera

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

The propagation of ultrasound through complex biological media, such as the human calvarium, poses a great challenge for modern medicine. Several ultrasonic techniques commonly used for treatment and diagnosis in most of the human body are still difficult to apply to the human brain, in part, because of the properties of the skull. Moreover, an understanding of the biomechanics of transcranial ultrasound may provide needed insight into the problem of blast wave induced traumatic brain injury (TBI). In the present study, the spatial variability of ultrasonic properties was evaluated for relevant frequencies of 0.5, 1, and 2.25 MHz. A total …

Nonlinear Mechanical Behavior Of The Human Common, External And Internal Carotid Arteries In Vivo, Alexey Kamenskiy, Yuris A. Dzenis, Jason N. Mactaggart, Thomas G. Lynch, Syed A. Jaffar Kazmi, Iraklis I. Pipinos

Department of Mechanical and Materials Engineering: Faculty Publications

Introduction—The mechanical environment and properties of the carotid artery play an important role in the formation and progression of atherosclerosis in the carotid bifurcation. The purpose of this work was to measure and compare the range and variation of circumferential stress and tangent elastic moduli in the human common (CCA), external (ECA) and internal (ICA) carotid arteries over the cardiac cycle in vivo.

Methods—Measurements were performed in the surgically exposed proximal cervical CCA, distal ECA and distal ICA of normotensive patients (n = 16) undergoing carotid endarterectomy. All measurements were completed in vivo over the cardiac cycle …

Preparation And Electrochemical Performance Of Tio2/Gns Nanocomposite As Anode Materials For Lithium-Ion Batteries, Lin-Lin Qin, Huan Zhang, Xiao-Jing Liu, Jian-Hui Xu, Yi-Ning Shi, Ming-Sen Zheng, Quan-Feng Dong

Journal of Electrochemistry

The honeycomb-like porous TiO₂/graphenes (TiO₂/GNs) nanocomposite was prepared by a reflux method. SEM and TEM results showed that nanosized anatase TiO₂ (about 5~10 nm) were dispersed uniformly on the surface of the GNs. The TiO₂/GNs composite showed excellent rate and cycling performance: A stable charge capacity of 169.5 mAh·g^-1 was obtained at 30C, and can restore to 241.7 mAh·g^-1 while current went back to 1C. The stable charge capacity of TiO₂/GNs nanocomposite electrode up to 201.9 mAh·g^-1 was achieved at 10C in the first cycle, and could be …

Novel Molten-Salt Electrolysis Processes Towards Low-Carbon Metallurgy, Wei Xiao, Hua Zhu, Hua-Yi Yin, De-Hua Wang

Journal of Electrochemistry

This review focuses on recent developments in molten-salt electrolytic metallurgical processes with respect to 1) high-efficiency metallurgical technologies via electrolytic reduction of solid oxides in molten chlorides and 2) zero-carbon-footprint electrochemical splitting metallurgical technologies. Initiating with an introduction on dynamic solid/solid/liquid three-phrase interlines electrochemistry for electrochemical reduction of solid cathode, the former aspect is discussed in terms of facilitating mass transfer throughout solid cathode, one-step production of functional alloy powders with the assistance of under-potential electroreduction of active metals and near-net-shape production of metal/alloy components. Whilst the latter is summarized by introducing some zero-carbon molten-salt electrolytic technologies including electro-splitting of …

Comments On Internal Alternating Current Resistance Test Standard And Methods Of Lithium-Ion Batteries, Ya-Li Zhang, Sen Xin, Yu-Guo Guo, Li-Jun Wan

Journal of Electrochemistry

The sustainable development of energy and environment is one of the most influential issues of this century. Batteries, especially secondary batteries are important for powering out daily life. However, in many practical applications, such as in electric vehicles and hybrid electric vehicles, batteries should be used in packs and the performance consistency of each battery in the pack should be taken into consideration. As one of the performance parameters being used to characterize the battery consistency, internal resistance is of great importance to the industrial fabrication and the use of batteries. Currently, internal resistance tests of secondary batteries, such as …

Methodological Significance Of "Property-Activity Relationship" For Catalyst Studies, Jun-Tao Lu, Li Xiao, De-Li Wang, Yu-Bao Sun, Yan-Ge Suo, Lin Zhuang

Journal of Electrochemistry

Instead of attempting the structure-activity relationship (SAR), which is commonly regarded as the core problem for catalyst studies, this paper highlights the methodological significance of “property-activity relationship (PAR)”. The “property” here refers to an index （such as the adsorption energy of an intermediate） or a group of indexes reflecting the behavior of a catalyst which interacts with reactants or intermediates, and is a bridge between structure and activity. Because property is related to activity more directly than structure to activity, PAR should be simpler, less difficult and, therefore, more feasible to be accessed than SAR. Once the key property is …

Simple Analysis And Possible Solutions Of The Unusual Interfacial Reactions In Li-S Batteries, Xin-Ping Ai, Yu-Liang Cao, Han-Xi Yang

Journal of Electrochemistry

Rechargeable Li-S batteries are a promising power source with realizable energy densities several times higher than current Li-ion batteries. However, the capacity utilization and cycling stability of the existing Li-S technologies are still insufficient for battery applications. The causes for the electrochemical instability of this redox system arise probably from the changes in the surface structures and electrochemical microenvironments of the Li anode and sulfur cathode during charge-discharge reactions, which includes the frustrated electron transfer in the sulfur-carbon interface, the dissoluble diffusion of the polysulfide intermediates, and the shuttle reaction inbetween the sulfur and Li electrodes. To deal with these …

Preparation And Characterization Of Prussian Blue Modified Nanoelectrode, Wei Wang, Bao-Fa Su, Dong-Ping Zhan

Journal of Electrochemistry

The Pt nanoelectrodes were fabricated by using a laser-based pipet puller and the recessed nanoelectrodes were prepared by etching of disk Pt nanoelectrodes wtih high frequency ac voltage. Prussian blue microcrystal was synthesized electrochemically on the both disk and recessed Pt nanoelectrodes. The strength of mechanical adhesion for the Prussian blue microcrystal on the nanoelectrode was enhanced. A novel method for the controllable synthesis of single particle is proposed, which has potential applications in modified electrodes and single particle electrocatalysis.

The Electrocatalytic Performance Of Pd Catalysts Supported On Pvp Modified Mwcnts For Formic Acid Oxidation, Jing Zhang, Xiao Zhao, Chang-Peng Liu, Wei Xing

Journal of Electrochemistry

In this paper the MWCNTs were modified by Poly (N-vinyl-2-pyrrolidone) (PVP) to support Pd nanoparticles, which were used as the catalyst for formic acid electrooxidation. And the performance of Pd/PVP-MWCNTs catalysts was studied by electrochemical measurements. The observations from Fourier transforms infrared spectrometer (FTIR) and transmission electron microscopy (TEM) illustrated that the Pd nanoparticles with a small size and narrow size distribution were highly dispersed on PVP-MWCNT support. Therefore, the Pd/PVP-MWCNTs catalysts showed excellent catalytic activity for formic acid electrooxidation.

Synthesis Of Spherical Ni3S4 By Solvothermal Method As Supercapacitor Electrodes, Qing-Na Huan, Li-Fang Jiao, Qing-Hong Wang, Hong-Mei Du, Jia-Qin Yang, Wen-Xiu Peng, Yi-Jing Wang, Hua-Tang Yuan

Journal of Electrochemistry

The Ni₃S₄ microspheres have been synthesized via a facile solvothermal method. The crystal structure and surface morphology are characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). Microspherical Ni₃S₄ exhibits good electrochemical capacitance validated by electrochemical measurements. The specific capacities of 1120.6 F∙g^-1 at 0.5 A∙g^-1 and 433.4 F∙g^-1 at 4 A∙g^-1 with the capacitance retention of 89.37 % and 84.88 % were obtained after 1000 cycles, respectively. The electrochemical reaction is expected due to the transformation of Ni(OH)₂ and NiOOH based on the XRD, XPS and CV …

Detection Of Pml/Rarî± Fusion Gene Using Gold Nanopaticles Modified Electrode By Chronocoulometry, Li-Man Wang, Li-Qing Lin, Shao-Huang Weng, Xin-Hua Lin, Yuan-Zhong Chen

Journal of Electrochemistry

A gold nanoparticles modified electrode was prepared by electrodeposition at constant potential. The sulfydryl modified probe was immobilized onto surface of gold nanoparticles via Au-S covalent bond and hybridized with complementary target DNA sequences, then the DNA sensor was fabricated for the detection of PML/RARα fusion gene by chronocoulometry in acute promyelocytic leukemia (APL). Scanning electron microscopy (SEM) and electrochemical impedance spectroscopy (EIS) were used to characterize the surface morphology of gold nanoparticles and the constructing process of sensor. With hexaammineruthenium(Ⅲ) chloride (RuHex) as a novel electrochemical indicator, the chronocoulometric DNA biosensor was employed to monitor artificial APL PML/RARα fusion …

Application Of First Principles Calculations In Anode Materials For Lithium Ion Batteries, Tian-Ran Zhang, Dai-Xin Li, Si-Qi Yang, Zhan-Liang Tao, Jun Chen

Journal of Electrochemistry

First principles calculations play an important role in the study and development of new materials for lithium batteries. In this paper, we review the application of first principles calculations in the design of anode materials, including the modeling of the interaction of lithium in the anode materials, capacity, voltage, electrochemical reaction process, diffusion, rate capability, the relationship between the structure and properties, and the experimental phenomena interpreting. Based on the discussions, we emphasize on the importance of first principles calculations and demonstrate their requirement for further development.

An Overview Of Electrode Materials In Microbial Fuel Cells, Su-Qin Ci, Na Wu, Zhen-Hai Wen, Jing-Hong Li

Journal of Electrochemistry

Microbial fuel cells (MFCs) are devices that can directly convert organic chemical energy into electrical energy with microbial as catalysts. MFCs are a promising bio-electrochemical system with the potential to degrade organic sewage and produce electricity. This article supplies a critical and comprehensive review for the electrode materials concerning about anode and cathode in MFCs, including the fabrications, functional modifications and surface constructions of electrode materials, as well as their applications in MFCs. Additionally, the existing problems of electrode materials in current MFCs have been demonstrated in order to provide the guideline for exploring the next-generation electrode materials for MFCs.

Preparation And Electrochemical Performance Of Tin@Mno Fibers By Coaxial Electrospinning, Chao-Qun Shang, Hai-Yan Yang, Xin-Hong Zhou, Zhong-Lei Man, Peng-Xian Han, Jian-Hua Yao, Yu-Long Duan, Guang-Lei Cui

Journal of Electrochemistry

In this study, the titanium nitride (TiN) @manganese oxide (MnO) core-shell structured fibers were prepared by the coaxial electrospinning using tetrabutyl titanate and manganese acetylacetonate as raw materials, and polyvinylpyrrolidone (PVP) as the template. And then the fibers were annealed in ammonia to finally obtain the coaxial TiN@MnO fibers. XRD, FESEM, TEM, EDX and physical adsorption instrument were used to characterize the phase structure, morphology, composition and specific surface areas and pore sizes of the samples. It was demonstrated that the as-synthesized TiN@MnO fibers possessed coaxial structure with a surface area of 16 m²·g^-1. As indicated …

Performnces Of Lini0.5Mn0.5O2 Thin Film Electrodes Prepared By Pulsed Laser Deposition, Yun-Hai Wan, Guo-Liang Yuan, Hui Xia

Journal of Electrochemistry

The all-solid-state thin-film Li-ion batteries with high energy density, power density and temperature stability are the ideal power sources for microelectronic devices. Developing new thin-film cathodes with large specific capacity is the key to their practical applications. The LiNi_0.5Mn_0.5O₂ with a layered structure has a higher reversible capacity and better structural stability compared with traditional LiCoO₂ cathode material. In this work, the LiNi_0.5Mn_0.5O₂ thin film cathodes were prepared by pulsed laser deposition. The effects of substrate material and temperature on the microstructure, surface morphology and composition of the thin …