Engineering Commons^™

Hydrogen Generation From Ammonia Borane And Water Through The Combustion Reactions With Mechanically Alloyed Al/Mg Powder, Daniel Rodriguez

Open Access Theses & Dissertations

Finding and developing a safe and effective method for hydrogen storage is integral to its use as an alternative source of energy. The goal of the studies described in this Thesis was to investigate the feasibility of developing combustible hydrogen-generating compositions based on ammonia borane and novel energetic materials such as nanocomposite and mechanically alloyed reactive materials, recently obtained by Prof. Edward Dreizin's team at the New Jersey Institute of Technology (NJIT). Such compositions could be stored for long time and release hydrogen on demand, upon ignition. The first phase of the research included thermodynamic calculations for combustion of ammonia …

Effect Of Rhenium On Short Term Oxidation Of Niobium Based Alloys For High Temperature Applications, Ruth M. Sierra

Open Access Theses & Dissertations

The effect of adding Re to Nb-based alloys and is intended to analyze in depth the microstructures of Nb based alloys with Re, Si and Cr additions, in atomic percentages. The binary alloys (Nb-5Re, Nb-5Si and Nb-5Cr) reveal the formation of a single phase, NbSS, NbSS+ Nb3Si and NbSS+NbCr2 respectively. The formation of the single phase was confirmed by TEM studies for the Nb-5Re alloy. Addition of Re to form ternary alloys, has helped in the formation of Nb5Si3 and (Nb, Re) Cr2, in Nb-5Re- 5Si and Nb-5Re-5Cr respectively. Quaternary alloy Nb-5Re-5Si-5Cr has Nb5Si3, NbCr2 and NbSS. The oxidation behavior …

Models Of Oil Wood Coating Materials Selection According To Technological, Operational, Ecological And Economic Criteria, Larysa Yaremchuk, Tetyana Olyanshyn, Volodymyr Maksymiv, Liliya Stepanivna Hogaboam

Engineering and Technology Management Faculty Publications and Presentations

This article presents the use of system analysis methodology and Graph Theory for validation of the relationships among descriptive factors, which impact the selection of oil materials for wood finishing. Matrix analysis was used to determine the results of the pair wise comparisons of factor weights and optimization of the factor values. Modelling theories have been developed, which allow for construction of models of primary impacts of the factors on oil materials selection in protective and decorative wood coatings creation.

Evaluation Of Different Harvesting And Storage Practices: Sweet Sorghum And Energycane, Ana Lucia Amaya Arroyave

LSU Master's Theses

Two attractive potential feed stocks for biofuel production are energycane and sweet sorghum due to the environmental adaptability, sugars concentration and yield. Evaluation and development of harvesting, transportation and storage practices is critical for bringing the production of these crops to industrial levels. This research aims to analyze the supply system of energy crops and evaluate the effect of different harvesting and storage in the yields of the feedstock and the efficiencies of the processes. Harvesting trials were conducted at St. Gabriel, LA for evaluating the feasibility of using energy crops as inputs for ethanol production. The parameters that were …

Characterization Of W-Ti-O Thin Films For Application In Photovoltaics, Amanda Patricia Christmas

Open Access Theses & Dissertations

Photovoltaic (PV) devices consist of the conversion of light energy into electricity. Nearly all PV technologies employ transparent conducting oxides (TCO) as an integral part of the de-vice structure so that the light can reach the semiconductor. The predominant transparent conducting oxide (TCO) that is currently being used in industry is indium tin oxide (ITO). However, Indium (In) is high in cost and becoming scarce in the world. This work is focused towards Titanium doped Tungsten oxide (WO3) for TCO application. The ultimate goal is making novel, cheaper, and efficient TCOs based on W-Ti-O films. Titanium will enhance the conductivity …

In-Situ Tem Plasma Chip Nanofabrication And Characterization, Xuebo Cui

Dissertations, Master's Theses and Master's Reports - Open

A silicon-based microcell was fabricated with the potential for use in in-situ transmission electron microscopy (TEM) of materials under plasma processing. The microcell consisted of 50 nm-thick film of silicon nitride observation window with 60μm distance between two electrodes. E-beam scattering Mont Carlo simulation showed that the silicon nitride thin film would have very low scattering effect on TEM primary electron beam accelerated at 200 keV. Only 4.7% of primary electrons were scattered by silicon nitride thin film and the Ar gas (60 μm thick at 1 atm pressure) filling the space between silicon nitride films. Theoretical calculation also showed …

Nanometric Structure-Property Relationship In Hafnium Oxide Thin Films Made By Sputter-Deposition, Mirella Vargas

Open Access Theses & Dissertations

Hafnium oxide (HfO2) is technologically an important material, which exhibits a unique set of properties such as a high dielectric constant (k~25) and wide band gap (~5.7 eV) which make this material attractive in the fields of microelectronics and optoelectronics. HfO2 has become the leading candidate to replace SiO2 dielectrics in gate oxides due to a higher permittivity and reportedly lower electron tunneling effects. HfO2 exhibits various polymorphs; the thermodynamic stability and phase existence depends on the temperature and pressure conditions. In addition, the controlled growth and manipulation of specific HfO2 crystal structures at the nanoscale dimensions is the driving …

Alkali Promoted Molybdenum (Iv) Sulfide Based Catalysts, Development And Characterization For Alcohol Synthesis From Carbon Monoxide And Hydrogen, Belinda Delilah Molina

Open Access Theses & Dissertations

For more than a century transition metal sulfides (TMS) have been the anchor of hydro-processing fuels and upgrading bitumen and coal in refineries worldwide. As oil supplies dwindle and environmental laws become more stringent, there is a greater need for cleaner alternative fuels and/or synthetic fuels. The depletion of oil reserves and a rapidly increasing energy demand worldwide, together with the interest to reduce dependence on foreign oil makes alcohol production for fuels and chemicals via the Fischer Tropsch synthesis (FTS) very attractive. The original Fischer-Tropsch (FT) reaction is the heart of all gas-to-liquid technologies; it creates higher alcohols and …

Growth And Analysis Of Micro And Nano Cdte Arrays For Solar Cell Applications, Brandon Adrian Aguirre

Open Access Theses & Dissertations

CdTe is an excellent material for infrared detectors and photovoltaic applications. The efficiency of CdTe/CdS solar cells has increased very rapidly in the last 3 years to ~20% but is still below the maximum theoretical value of 30%. Although the short-circuit current density is close to its maximum of 30 mA/cm2, the open circuit voltage has potential to be increased further to over 1 Volt. The main limitation that prevents further increase in the open-circuit voltage and therefore efficiency is the high defect density in the CdTe absorber layer. Reducing the defect density will increase the open-circuit voltage above 1 …

Combustion Synthesis Of Molybdenum Silicides And Borosilicides For Ultrahigh-Temperature Structural Applications, Mohammad Shafiul Alam

Open Access Theses & Dissertations

Molybdenum silicides and borosilicides are promising structural materials for gas-turbine power plants. A major challenge, however, is to simultaneously achieve high oxidation resistance and acceptable mechanical properties at high temperatures. For example, molybdenum disilicide (MoSi₂) has excellent oxidation resistance and poor mechanical properties, while Mo-rich silicides such as Mo₅Si₃ (called T₁) have much better mechanical properties but poor oxidation resistance. One approach is based on the fabrication of MoSi₂−T₁ composites that combine high oxidation resistance of MoSi₂ and good mechanical properties of T₁. Another approach involves the …

Gadolinia Doped Hafnia (Gd2o3- Hfo2) Thermal Barrier Coatings For Gas Turbine Applications, Satya Kiran Gullapalli

Open Access Theses & Dissertations

Thermal efficiency of the gas turbines is influenced by the operating temperature of the hot gas path components. The material used for the hot gas path components can only withstand temperature up to a certain limit. Thermal barrier coatings (TBC) provide the additional thermal protection for these components and help the gas turbine achieve higher firing temperatures. Traditionally available yttria stabilized zirconia (YSZ) TBCs have a limitation up to 1200 C due to their phase transformation. The present work focuses on gadolinia based hafnia (GSH) TBCs to study their potential to replace the YSZ coatings. Different compositions of gadolinia doped …

Design Of Three Different Particle Size Distributions In Silver Paste Through Computer Simulation For Higher Electrical Conductivity, Kyungdeok Jang

Open Access Theses & Dissertations

In the field of printed electronics technology, researchers have tried to print highly conductive electrodes with fine width and height in order to manufacture high performance devices.

The purpose of this research is to print particle monolayer silver patterns which have better electrical conductivity than existing ones. The key idea of this experiment is to analyze silver inks with different sized particles. Let us consider a particle monolayer pattern printed with silver ink consisting of mono-sized particles. Inside of the pattern, there are some vacant spaces between the particles, which can lead to low electrical conductivity and discontinuity of the …

Fabrication Of A Nickel-Based Superalloy In Electron Beam Melting And Process Improvements Using Thermal Feedback From A Multi-Wavelength Pyrometer, Jonathan Minjares

Open Access Theses & Dissertations

The focus of this research was to fabricate parts composed of a nickel-based superalloy containing high levels of aluminum and titanium (NSAT) by using electron beam melting (EBM) additive manufacturing (AM) technology and utilizing thermal feedback from a multi-wavelength pyrometer to perform process improvements leading to near defect-free parts. EBM is an AM technology that utilizes metal powder to fabricate parts in layer-by-layer manner. A multi-wavelength pyrometer was implemented in an Arcam S12 (Arcam AB, Sweden) EBM system to observe and record surface temperatures throughout fabrication. Temperature data from the EBM system and the multi-wavelength pyrometer were graphed using MATLAB …

A Study Of Ti-Doped Wo3 Thin Films Using Comparative Theoretical And Experimental Approach, Aurelio Paez

Open Access Theses & Dissertations

Metal oxides like Tungsten Oxide (WO3) are well documented and characterized in the literature, with uses in darkening windows and mirrors, flat computer displays, solar panel cooling, and sensors (of interest in this study). Ti doping of WO3 is less documented and the focus of this study. Sample thin films of pure WO3 and varyingly Ti doped WO3 were prepared using Radio Frequency magnetron sputtering (RF) (13.56 MHz) to grow thin films on a silicon substrate. This study aims to compare multiple Ti doping percentages in WO3 theoretically and then compare with experimental data taken from thin films of various …

Polymer Aggregation Correlated Transition From Schottky-Junction To Bulk Heterojunction Organic Solar Cells, Bin Yang, Zhengguo Xiao, Jinsong Huang

Department of Mechanical and Materials Engineering: Faculty Publications

The fullerene-based organic Schottky-junction solar cells have recently attracted intensive research interest because of their unique electrical performance, such as significant photocurrent generation from excitons created in fullerenes and large open-circuit voltage (V_OC) output induced by high Schottky-barrier height between the anode and the fullerene acceptor. This manuscript reports another remarkably appealing advantage that the fullerene-based Schottky-junction solar cells are more stable than the bulk heterojunction counterparts. The better stability is likely due to mitigative polymer photo-oxidation and/or little morphological change of active film in the aged Schottky-junction devices. The transition from Schottky-junction to bulk heterojunction appears at …

Phase Transitions In Mechanically Milled Mn-Al-C Permanent Magnets, Michael J. Lucis, Timothy E. Prost, Xiujuan Jiang, Meiyu Wang, Jeffrey E. Shield

Department of Mechanical and Materials Engineering: Faculty Publications

Mn-Al powders were prepared by rapid solidification followed by high-energy mechanical milling. The rapid solidification resulted in single-phase ε. The milling was performed in both the ε phase and the τ phase, with the τ-phase formation accomplished through a heat treatment at 500 °C for 10 min. For the ε-milled samples, the conversion of the ε to the τ phase was accomplished after milling via the same heat treatment. Mechanical milling induced a significant increase in coercivity in both cases, reaching 4.5 kOe and 4.1 kOe, respectively, followed by a decrease upon further milling. The increase in coercivity was the …

Biomechanical Strain As A Trigger For Pore Formation In Schlemm’S Canal Endothelial Cells, Sietse T. Braakman, Ryan M. Pedrigi, A. Thomas Read, James A. E. Smith, W. Daniel Stamer, C. Ross Ethier, Darryl R. Overby

Department of Mechanical and Materials Engineering: Faculty Publications

The bulk of aqueous humor passing through the conventional outflow pathway must cross the inner wall endothelium of Schlemm’s canal (SC), likely through micron-sized transendothelial pores. SC pore density is reduced in glaucoma, possibly contributing to obstructed aqueous humor outflow and elevated intraocular pressure (IOP). Little is known about the mechanisms of pore formation; however, pores are often observed near dome-like cellular outpouchings known as giant vacuoles (GVs) where significant biomechanical strain acts on SC cells. We hypothesize that biomechanical strain triggers pore formation in SC cells. To test this hypothesis, primary human SC cells were isolated from three non-glaucomatous …

Altered Mechanobiology Of Schlemm’S Canal Endothelial Cells In Glaucoma, Darryl R. Overby, Enhua H. Zhou, Rocio Vargas-Pinto, Ryan M. Pedrigi, Rudolf Fuchshofer, Sietse T. Braakman, Ritika Gupta, Kristin M. Perkumas, Joesph M. Sherwood, Amir Vahabikashi, Quynh Dang, Jae Hun Kim, C. Ross Ethier, W. Daniel Stamer, Jeffrey J. Fredberg, Mark Johnson

Department of Mechanical and Materials Engineering: Faculty Publications

Increased flow resistance is responsible for the elevated intraocular pressure characteristic of glaucoma, but the cause of this resistance increase is not known. We tested the hypothesis that altered biomechanical behavior of Schlemm’s canal (SC) cells contributes to this dysfunction. We used atomic force microscopy, optical magnetic twisting cytometry, and a unique cell perfusion apparatus to examine cultured endothelial cells isolated from the inner wall of SC of healthy and glaucomatous human eyes. Here we establish the existence of a reduced tendency for pore formation in the glaucomatous SC cell—likely accounting for increased outflow resistance—that positively correlates with elevated subcortical …

Arising Applications Of Ferroelectric Materials In Photovoltaic Devices, Yongbo Yuan, Zhengguo Xiao, Bin Yang, Jinsong Huang

Department of Mechanical and Materials Engineering: Faculty Publications

The ferroelectric-photovoltaic (FE-PV) device, in which a homogeneous ferroelectric material is used as a light absorbing layer, has been investigated during the past several decades with numerous ferroelectric oxides. The FE-PV effect is distinctly different from the typical photovoltaic (PV) effect in semiconductor p–n junctions in that the polarization electric field is the driving force for the photocurrent in FE-PV devices. In addition, the anomalous photovoltaic effect, in which the voltage output along the polarization direction can be significantly larger than the bandgap of the ferroelectric materials, has been frequently observed in FE-PV devices. However, a big challenge faced by …

Equipment Fragility Due To Shock Response, Christopher Y. Tuan

Department of Civil and Environmental Engineering: Faculty Publications

Because of its simplicity, the shock response spectrum has become widely used as a means of describing the shock responses and fragilities of structures and equipment. This paper focuses on the drawbacks of using the shock response spectrum for defining equipment shock tolerance. A cantilever beam with a tip mass was used to model a hypothetical piece of equipment subjected to strong ground motion such as that caused by an explosion. The exact solution from a detailed modal analysis shows that multiple modes of response were excited. Contributions from higher modes can be more predominant than that from the fundamental …

Electrospinning Applications Air Filtration And Superhydrophobic Materials, Negar Ghochaghi, Adetoun Taiwo

Graduate Research Posters

Electrospinning is a widely applicable technique that generates non-woven fibers in the micro and nano range. In this project two of its applications are highlighted namely filtration media and enhancement of wettability. The first project demonstrates that electrospinning can be used to produce new fiber filtration media with controlled microstructure. The bimodal and unimodal orthogonal and random filters were made and characterized against their filtration efficiency and pressure drop. Figure of Merit (FOM) was also calculated and discussed. It is shown that the FOM increases when the electrospun fibers are arranged into alternating layers of aligned course and fine fibers. …

Room-Temperature Spin-Polarized Organic Light-Emitting Diodes With A Single Ferromagnetic Electrode, Baofu Ding, Qunliang Song, Kamal Alameh

Research outputs 2014 to 2021

In this paper, we demonstrate the concept of a room-temperature spin-polarized organic light-emitting diode (Spin-OLED) structure based on (i) the deposition of an ultra-thin p-type organic buffer layer on the surface of the ferromagnetic electrode of the Spin-OLED and (ii) the use of oxygen plasma treatment to modify the surface of that electrode. Experimental results demonstrate that the brightness of the developed Spin-OLED can be increased by 110% and that a magneto-electroluminescence of 12% can be attained for a 150 mT in-plane magnetic field, at room temperature. This is attributed to enhanced hole and room-temperature spin-polarized injection from the ferromagnetic …

Bimetallic Non-Alloyed Nps For Improving The Broadband Optical Absorption Of Thin Amorphous Silicon Substrates, Chee L. Tan, Sung J. Jang, Young M. Song, Kamal Alameh, Yong T. Lee

Research outputs 2014 to 2021

We propose the use of bimetallic non-alloyed nanoparticles (BNNPs) to improve the broadband optical absorption of thin amorphous silicon substrates. Isolated bimetallic NPs with uniform size distribution on glass and silicon are obtained by depositing a 10-nm Au film and annealing it at 600°C; this is followed by an 8-nm Ag film annealed at 400°C. We experimentally demonstrate that the deposition of gold (Au)-silver (Ag) bimetallic non-alloyed NPs (BNNPs) on a thin amorphous silicon (a-Si) film increases the film's average absorption and forward scattering over a broad spectrum, thus significantly reducing its total reflection performance. Experimental results show that Au-Ag …

Structure Health Monitoring (Shm) System Trade Space Analysis, Salman A. Albinali, David R. Jacques

Faculty Publications

An analytic approach to exploring the tradespace associated with Structural Health Monitoring (SHM) systems is presented. Modeling and simulation of the life cycle of a legacy aircraft and the expected operational and maintenance events that could occur is shown. A focus on the SHM system detection of a significant crack length and the possibility of False Alarm (FA), miss detection and mishap events is investigated. The modeling approach allows researchers to explore the tradespace associated with safe and critical crack lengths, sensor thresholds, scheduled maintenance intervals, falsely triggered maintenance actions, and mishaps due to missed detections. As one might expect, …

Localized Corrosion Behavior Of Sensitized 304 Stainless Steel By Scanning Reference Electrode Technique, Chen-Qing Ye, Rong-Gang Hu, Rui-Qing Hou, Xiao-Ping Wang, Rong-Gui Du, Chang-Jian Lin

Journal of Electrochemistry

Based on a home-built setup of scanning reference electrode technique, and combined with conventional electrochemical measurements, the localized corrosion behavior of sensitized 304 stainless steel (304ss) had been investigated in this work. The results showed that, the non-sensitized 304ss or 304ss sensitized at 550 oC was susceptible to pitting; while 304ss sensitized at 650 oC or 750 oC suffered severe intergranular corrosion in 10% FeCl3 solution.

Application Of Synchrotron Radiation Based Electrochemical In-Situ Techniques To Study Of Electrode Materials For Lithium-Ion Batteries, Zheng-Liang Gong, Wei Zhang, Dong-Ping Lv, Xiao-Gang Hao, Wen Wen, Zheng Jiang, Yong Yang

Journal of Electrochemistry

Due to its merits of high brightness and high intensity, high level of polarization and wide tunability in energy, etc., synchrotron radiation technique provides an unique platform for analysis of the relationship among composition–structure–performance of materials for lithium ion batteries, especially for in-situ, real time dynamic investigation of the electrochemical reaction mechanism, aging process and failure mechanism during charge-discharge cycling. In this paper, we review the latest developments in application of synchrotron based electrochemical in-situ experimental methods to studies of lithium ion batteries. The paper mainly focuses on the application of electrochemical in-siu XRD and XAFS techniques to the investigations …

Controllable Synthesis Of Dispersed Spherical Fe3O4 Nanoparticles As Lithium-Inserted Materials, Hong-Li Zou, Wei-Shan Li

Journal of Electrochemistry

Dispersed spherical Fe₃O₄ nanoparticles were synthesized by a hydrothermal method. The influences of odecyl trimethyl ammonium bromide (DTAB) concentration on the morphology and particle size of the as-prepared Fe₃O₄ were studied. Electrochemical performance of the as-prepared sample as anode materials of lithium ion battery was investigated. It is found that the as-prepared sample exhibits superior rate performance and cycle performance. The nano-sized materials provide structural stability and favor the transfer of lithium ions.

An Investigation On The Solid Electrolyte Interphase Of Silicon Anode For Li-Ion Batteries Through Force Curve Method, Jie-Yun Zheng, Hao Zheng, Rui Wang, Hong Li, Li-Quan Chen

Journal of Electrochemistry

Non-aqueous electrolyte has been widely used in commercial Li-ion batteries. Optimized choices are proceeding among the various types of salts and solvents in an effort to achieve higher performance of electrolyte. However, the electrolyte will be reduced in low potential and the reductive product will be deposited on the surface of anode to form a passivating layer, solid electrolyte interphase (SEI). Herein an atomic force microscopy (AFM) based method was introduced to study the structure and mechanical property of SEI on silicon thin film anode during the first cycle. Silicon has been known as the most potential candidate anode for …

Preparation And Electrochemical Properties Of Flake-Like Liv3O8 By Soft Template Assisted Sol-Gel Method As Anode Material For Aqueous Li-Ion Battery, Shuai Tan, Dan Sun, Hai-Yan Wang, Tian-Li Hou, Zhong-Xing Xiao, You-Gen Tang

Journal of Electrochemistry

Composite electrode of CuF₂/MoO₃/C was fabricated through high energy mechanical milling. The properties of CuF₂/MoO₃/C were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), high resolution transmission electron microscopy (TEM), galvanostatic charge-discharge measurements, cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). The results showed that the grain sizes of CuF₂ and MoO₃ after milling were 200 ~ 300 nm, and the initial discharge capacity of CuF₂/MoO₃/C was 647 mAh·g^-1 at room temperature and at a current density of 10 mAh·g^-1. However, the …

Synthesis And Electrochemical Performance Of Nano Licopo4 By Polyol Method, Fei Wang, Yang Jun

Journal of Electrochemistry

High potential LiCoPO₄ cathode material was synthesized by polyol method. Carbon layer of ca. 3 nm thick was coated on the LiCoPO₄ surfaces by chemical vapor deposition from methylbenzene. Crystalline structure, morphology and electrochemical performance of the sample were studied by XRD, SEM, TEM, CV and galvanostatic charge/discharge curve. The synthesized material via polyol method showed a pure phase of LiCoPO₄. The LiCoPO₄/C electrode delivered a high discharge capacity of 132 mAh·g^-1 and maintained 78% of the initial capacity after 50 cycles at 0.1C rate. The two-step extraction/insertion behavior of Li⁺ in …