Engineering Commons^™

Towards Tuning The Mechanical Properties Of Three-Dimensional Collagen Scaffolds Using A Coupled Fiber-Matrix Model, Shengmao Lin, Lauren A. Hapach, Cynthia Reinhart-King, Linxia Gu

Department of Mechanical and Materials Engineering: Faculty Publications

Scaffold mechanical properties are essential in regulating the microenvironment of three-dimensional cell culture. A coupled fiber-matrix numerical model was developed in this work for predicting the mechanical response of collagen scaffolds subjected to various levels of non-enzymatic glycation and collagen concentrations. The scaffold was simulated by a Voronoi network embedded in a matrix. The computational model was validated using published experimental data. Results indicate that both non-enzymatic glycation-induced matrix stiffening and fiber network density, as regulated by collagen concentration, influence scaffold behavior. The heterogeneous stress patterns of the scaffold were induced by the interfacial mechanics between the collagen fiber network …

Development And Preliminary Evaluation Of A Spray Deposition Sensing System For Improving Pesticide Application, Melissa A. Kesterson, Joe D. Luck, Michael P. Sama

Department of Mechanical and Materials Engineering: Faculty Publications

An electronic, resistance-based sensor array and data acquisition system was developed to measure spray deposition from hydraulic nozzles. The sensor surface consisted of several parallel tin plated copper traces of varying widths with varying gap widths. The system contained an embedded microprocessor to monitor output voltage corresponding to spray deposition every second. In addition, a wireless module was used to transmit the voltage values to a remote laptop. Tests were conducted in two stages to evaluate the performance of the sensor array in an attempt to quantify the spray deposition. Initial tests utilized manual droplet placement on the sensor surface …

Multiscale Modeling Of Skeletal Muscle Active Contraction In Relation To Mechanochemical Coupling Of Molecular Motors, Jiangcheng Chen, Xiaodong Zhang, Shengmao Lin, He Wang, Linxia Gu

Department of Mechanical and Materials Engineering: Faculty Publications

In this work, a mathematical model was developed to relate the mechanochemical characterizations of molecular motors with the macroscopic manifestation of muscle contraction. Non-equilibrium statistical mechanics were used to study the collective behavior of myosin molecular motors in terms of the complex conformation change and multiple chemical states in one working cycle. The stochastic evolution of molecular motor probability density distribution during the contraction of sarcomere was characterized by the Fokker-Planck Equation. Quick muscle contraction was demonstrated by the collective dynamic behavior of myosin motors, the muscle contraction force, and the muscle contraction velocity-force relation. Our results are validated against …

Inducing Persistent Flow Disturbances Accelerates Atherogenesis And Promotes Thin Cap Fibroatheroma Development In D374y-Pcsk9 Hypercholesterolemic Minipigs, Ryan M. Pedrigi, Christian Bo Poulsen, Vikram V. Mehta, Niels Ramsing Holm, Nilesh Pareek, Anouk L. Post, Ismail Dogu Kilic, Winston A.S. Banya, Gianni Dall'ara, Alessio Mattesini, Martin M. Bjorklund, Niels P. Andersen, Anna K. Grondal, Enrico Petretto, Nicolas Foin, Justin E. Davies, Carlo Di Mario, Jacob Fog Bentzon, Hans Erik Botker, Erling Falk, Rob Krams, Ranil De Silva

Department of Mechanical and Materials Engineering: Faculty Publications

Background—Although disturbed flow is thought to play a central role in the development of advanced coronary atherosclerotic plaques, no causal relationship has been established. We evaluated whether inducing disturbed flow would cause the development of advanced coronary plaques, including thin cap fibroatheroma (TCFA).

Methods and Results—D374Y-PCSK9 hypercholesterolemic minipigs (N=5) were instrumented with an intracoronary shear-modifying stent (SMS). Frequency-domain optical coherence tomography was obtained at baseline, immediately post-stent, 19, and 34 weeks and used to compute shear stress metrics of disturbed flow. At 34 weeks, plaque type was assessed within serially-collected histological sections and co-registered to …

Self‑Propelled Droplets On Heated Surfaces With Angled Self‑Assembled Micro/Nanostructures, Cory Kruse, Isra Somanas, Troy Anderson, Chris Wilson, Craig Zuhlke, Dennis Alexander, George Gogos, Sidy Ndao

Department of Mechanical and Materials Engineering: Faculty Publications

Directional and ratchet-like functionalized surfaces can induce liquid transport without the use of an external force. In this paper, we investigate the motion of liquid droplets near the Leidenfrost temperature on functionalized self-assembled asymmetric microstructured surfaces. The surfaces, which have angled microstructures, display unidirectional properties. The surfaces are fabricated on stainless steel through the use of a femtosecond laser-assisted process. Through this process, mound-like microstructures are formed through a combination of material ablation, fluid flow, and material redeposition. In order to achieve the asymmetry of the microstructures, the femtosecond laser is directed at an angle with respect to the sample …

Quantification Of Ultraprecision Surface Morphology Using An Algebraic Graph Theoretic Approach, Prahalad Rao, Satish T. S. Bukkapatnam, Zhenyu (James) Kong, Omer F. Beyca, Kenneth Case, Ranga Komanduri

Department of Mechanical and Materials Engineering: Faculty Publications

Assessment of progressive, nano-scale variation of surface morphology during ultraprecision manufacturing processes, such as fine-abrasive polishing of semiconductor wafers, is a challenging proposition owing to limitations with traditional surface quantifiers. We present an algebraic graph theoretic approach that uses graph topological invariants for quantification of ultraprecision surface morphology. The graph theoretic approach captures heterogeneous multi-scaled aspects of surface morphology from optical micrographs, and is therefore valuable for in situ real-time assessment of surface quality. Extensive experimental investigations with specular finished (Sa ~ 5 nm) blanket copper wafers from a chemical mechanical planarization (CMP) process suggest that the proposed method was …

Evaluation Of Peritoneal Microbubble Oxygenation Therapy In A Rabbit Model Of Hypoxemia, Nathan D. Legband, Jameel A. Feshitan, Mark A. Borden, Benjamin S. Terry

Department of Mechanical and Materials Engineering: Faculty Publications

Alternative extrapulmonary oxygenation technologies are needed to treat patients suffering from severe hypoxemia refractory to mechanical ventilation. We previously demonstrated that peritoneal microbubble oxygenation (PMO), in which phospholipid-coated oxygen microbubbles (OMBs) are delivered into the peritoneal cavity, can successfully oxygenate rats suffering from a right pneumothorax. This study addressed the need to scale up the procedure to a larger animal with a splanchnic cardiac output similar to humans. Our results show that PMO therapy can double the survival time of rabbits experiencing complete tracheal occlusion from6.6 ± 0.6 min for the saline controls to 12.2 ± 3.0 min for the …

Enhanced Pool-Boiling Heat Transfer And Critical Heat Flux On Femtosecond Laser Processed Stainless Steel Surfaces, Cory M. Kruse, Troy Anderson, Chris Wilson, Craig Zuhlke, Dennis Alexander, George Gogos, Sidy Ndao

Department of Mechanical and Materials Engineering: Faculty Publications

In this paper, we present an experimental investigation of pool boiling heat transfer on multiscale (micro/nano) functionalized metallic surfaces. Heat transfer enhancement in metallic surfaces is very important for large scale high heat flux applications like in the nuclear power industry. The multiscale structures were fabricated via a femtosecond laser surface process (FLSP) technique, which forms self-organized mound-like microstructures covered by layers of nanoparticles. Using a pool boiling experimental setup with deionized water as the working fluid, both the heat transfer coefficients and critical heat flux were investigated. A polished reference sample was found to have a critical heat flux …

An Agent Based Approach For Simulating Demo Enterprise Models, Mamadou Seck, Joseph Barjis

Engineering Management & Systems Engineering Faculty Publications

DEMO (design and engineering methodology for organization) is a theoretically grounded methodology for rigorous enterprise modeling. It provides relevant concepts from a construction perspective. As the methodology gains a wider audience, there is a growing interest in simulating DEMO models. Most attempts to develop a simulation approach for enterprise models in general, and the DEMO methodology in particular, are based on process oriented conceptualizations that are typically implementation in a discrete event paradigm. In this paper, we propose a conceptual framework for the translation of DEMO models into an agent based simulation. We will describe the DEMO methodology in some …

Effects Of Forcing Time Scale On The Simulated Turbulent Flows And Turbulent Collision Statistics Of Inertial Particles, B. Rosa, H. Parishani, O. Ayala, L.-P. Wang

Engineering Technology Faculty Publications

In this paper, we study systematically the effects of forcing time scale in the large-scale stochastic forcing scheme of Eswaran and Pope ["An examination of forcing in direct numerical simulations of turbulence," Comput. Fluids 16, 257 (1988)] on the simulated flow structures and statistics of forced turbulence. Using direct numerical simulations, we find that the forcing time scale affects the flow dissipation rate and flow Reynolds number. Other flow statistics can be predicted using the altered flow dissipation rate and flow Reynolds number, except when the forcing time scale is made unrealistically large to yield a Taylor microscale flow Reynolds …

Effects Of Gravity On The Acceleration And Pair Statistics Of Inertial Particles In Homogeneous Isotropic Turbulence, H. Parishani, O. Ayala, B. Rosa, L.-P. Wang, W. W. Grabowski

Engineering Technology Faculty Publications

Within the context of heavy particles suspended in a turbulent airflow, we study the effects of gravity on acceleration statistics and radial relative velocity (RRV) of inertial particles. The turbulent flow is simulated by direct numerical simulation (DNS) on a 256³ grid and the dynamics of O(10⁶) inertial particles by the point-particle approach. For particles/droplets with radius from 10 to 60 µm, we found that the gravity plays an important role in particle acceleration statistics: (a) a peak value of particle acceleration variance appears in both the horizontal and vertical directions at a particle Stokes number …

Context Aware Textual Entailment, Soha Arab-Khazaeli

LSU Doctoral Dissertations

In conversations, stories, news reporting, and other forms of natural language, understanding requires participants to make assumptions (hypothesis) based on background knowledge, a process called entailment. These assumptions may then be supported, contradicted, or refined as a conversation or story progresses and additional facts become known and context changes. It is often the case that we do not know an aspect of the story with certainty but rather believe it to be the case; i.e., what we know is associated with uncertainty or ambiguity. In this research a method has been developed to identify different contexts of the input raw …

Microindentation Of Bi57in26sn17 Lead-Free Alloy, Ruiting Zhao

Theses and Dissertations--Chemical and Materials Engineering

There is great need to understand the mechanical properties of lead-free alloys—an alternative of lead-based alloys—to address the environmental problems associated with the use of lead-based materials in microelectronics. In this work, the microstructures of Bi57In26Sn17 lead-free alloy were examined using Optical Microscopy and Energy Dispersive X-ray Spectroscopy analysis. The micro-indentation technique was used to study the mechanical properties of Bi57In26Sn17 lead-free alloy. The experimental results of the hardness and contact modulus were presented and discussed. Local creep during the indentation was observed from the load-displacement curves. The Vickers hardness (HV) increases with the decrease of the indentation depth, suggesting …

Binder Jet Additive Manufacturing Of Stainless Steel-Hydroxyapatite Bio-Composite, Don Suranga Dhanushka Uduwage

All Graduate Theses, Dissertations, and Other Capstone Projects

This study was conducted to create a bio-composite with a porous structure using the binder-jet printing additive manufacturing process. The samples were printed by changing the parameters such as layer thickness, roller speed, sintering time and sintering temperature of the X1-Lab binder jet additive manufacturing printer. The samples were printed 80% stainless steel 316 mixed with 20% Calcium Phosphate Tribasic by volume. Eight experiments were attempted to print according to the fractional factorial design of experiment. The effects of changing parameters on the mechanical properties of the new bio-composite was tested using ASTM E-09 compressive strength standards. The compression testing …

Product Parameters Optimization For Double Purge Of C-Magma Integrated With Conventional Three-Boiling Crystallization Scheme To Improve Raw Sugar Whole Color, Luz Stella Polanco

LSU Doctoral Dissertations

Efficient crystallization in raw sugar production is the result of a combination of factors and responses that meet specific criteria. Matching a sugar quality standard, maximizing sugar yield, maximizing crystallization equipment capacity and minimizing heat requirement are all necessary optimization criteria. A double centrifugation or purge of C-magma is intended to improve raw sugar whole color by the reduction of color recirculation with the sugar crystal. Combining a three boiling crystallization scheme with a second centrifugation after the last crystallization stage required optimizing the input/output product parameters (purities) and the location of the liquid recycle component (double purge molasses) for …

Interorganizational Collaboration And Systemic Change Framework For Building Information Modeling (Bim) Adoption, Rehema Joseph Monko

LSU Doctoral Dissertations

It was found that an integrated framework needs to be developed for the construction industry that allows optimized interorganizational collaboration and systemic change while using Building Information Modeling (BIM) technologies. The framework needs to be effective so the industry can adopt BIM through a set of interdependent activities beyond their organizational boundaries. The adoption has been proven difficult because of industry competitiveness and a fragmented work environment. Meanwhile, existing frameworks vary between studies. This research developed an integrated framework, identified critical factors, and provided an evaluation guide for interorganizational collaboration and set of coordinated changes necessary to adopt BIM. This …

Influence Of Spatial Variations Of Railroad Track Stiffness And Material Inclusions On Fatigue Life, Celestin Nkundineza

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Railroad transportation is very important for economic growth and effective maintenance is one critical factor for its economic sustainability. The high repetitive forces from a moving railcar induce cyclic stresses that lead to rail bending and potential deterioration due to fatigue crack initiation and propagation. Previous research for prediction of fatigue life has been done under the assumptions of a uniform track bed and a homogeneous rail. However the spatial variation of the track stiffness is expected to increase the maximum stresses in the rail and, therefore, accelerate the fatigue process. The research described in this dissertation is focused on …

A Study To Evaluate Non-Uniform Phase Maps In Shape Memory Alloys Using Finite Element Method, Naren Motte

Theses and Dissertations

The unique thermo-mechanical behavior of Shape Memory Alloys (SMAs), such as their ability to recover the original shape upon heating or being able to tolerate large deformations without undergoing plastic transformations, makes them a good choice for actuators.

This work studies their application in the aerospace and defense industries where SMA components can serve as release mechanisms for gates of enclosures that have to be deployed remotely. This work provides a novel approach in evaluating the stress and heat induced change of phase in a SMA, in terms of the transformation strain tensor. In particular, the FEA tool

ANSYS has …

Thiol-Ene Scaffolds As Synthetic Augments And Silicate Ceramics As Osteogenic Components For Bone Tissue Engineering Applications, Cong Chen

LSU Doctoral Dissertations

Bone tissue engineering approaches using polymer/ceramic composites show promise as effective biocompatible, absorbable, and osteoinductive materials. A novel class of in situ polymerizing thiol-acrylate based copolymers synthesized via an amine-catalyzed Michael addition was studied for its potential to be used in bone defect repair. Both pentaerythritol triacrylate-co-trimethylolpropane tris(3-mercaptopropionate) (PETA-co-TMPTMP) and PETA-co-TMPTMP with hydroxyapatite composites were fabricated in solid cast and foamed forms. These materials were characterized chemically and mechanically followed by an in vitro evaluation of the biocompatibility and chemical stability in conjunction with human adipose-derived mesenchymal pluripotent stem cells (hASC). The solid PETA-co-TMPTMP with and without hydroxyapatite (HA) exhibited …

Release, Stability And Functionality Of Nanodelivered Hydrophobic (Lutein And Beta-Carotene) And Hydrophilic (Folic Acid) Antioxidants Using Zein Nanoparticles, Thanida Chuacharoen

LSU Doctoral Dissertations

Nanodelivery systems enable innovations that can benefit foods and human health on a large scale in the coming years. The instabilities of antioxidants during food processing and during digestion are drawbacks that can be successfully addressed by nanoentrapment. This research provided technical strategies to synthesize zein nanoparticles loaded with hydrophobic/hydrophilic antioxidants, and to study the release profiles and physical stability of nanocarriers and chemical stability of entrapped bioactives under on-shelf and GI conditions. The results supported the potential of zein nanoparticles stabilized by surfactants to improve chemical stability of entrapped lutein, and to slowly release lutein under PBS conditions. Same …

Optimal Location Of Biomethane Gas Manufacturing Plants And Allocation Of Feedstock And Liquified Carbon Product, Bingqing Wu

LSU Doctoral Dissertations

Biomethane gas (BMG), known for its sustainability, low environmental impact, and high profitability, has received wide attention in recent years. To facilitate the process of making strategic plans for building a BMG production system, this dissertation leverages the mathematical modeling and optimization techniques to minimize the supply chain cost for such a system. Typical elements in a BMG production system consist of the local farms that produce the feedstock, the hubs that collect and store the feedstock produced by farms, the reactors that generate BMG from the feedstock transported from the hubs, the condensers that liquefy the BMG from the …

Image-Based Modeling Of Porous Media Using Fem And Lagrangian Particle Tracking, Paula Cysneiros Sanematsu

LSU Doctoral Dissertations

The study of fundamental flow and transport processes at the pore scale is essential to understanding how the mechanisms affect larger, field-scale, processes that occur in oil and gas recovery, groundwater flow, contaminant transport, and CO2 sequestration. Pore-scale imaging and modeling is one of the techniques used to investigate these fundamental mechanisms. Although extensive development of pore-scale imaging and modeling has occurred recently, some areas still need further advances. In this work, we address two areas: (1) imaging of bulk proppants and proppant-filled fractures under varying loading stress and flow simulation in these systems and (2) nanoparticle (NP) transport modeling …

Thermo-Catalytic Upgrading Of Pyrolysis Vapors Using Electromagnetic Heating, Pranjali Devidas Muley

LSU Doctoral Dissertations

Electromagnetic heating offers several advantages such as rapid heating rates, accurate temperature control and energy efficiency over conventional reactors. The goal of this study was to design an effective and energy efficient catalytic reactor for pyrolysis vapor upgrading. An induction based catalytic reactor was designed for upgrading of pyrolysis vapors. The effect of catalyst bed temperatures (290°, 330° and 370°C) and biomass to catalyst ratios of 1, 1.5 and 2 was studied. The results were compared to conventional heating reactor. Induction heating reactor performance exceeded that of conventional heater. The biomass to catalyst ratio of 2 in combination with the …

Time-Resolved Investigations Of Continuous Flow Synthesis Of Nanomaterials And Catalysis Using Millifluidic Reactors For Biomass Conversion Reactors, Chelliah V Navin

LSU Doctoral Dissertations

Millifluidics can be used as a simple tool and convenient platform to perform in-situ investigations on nanoparticles synthesis to generate real-time information in a continuous flow fashion. These investigations can be used to observe the relationship between the structure and performance of nanoparticles for catalytic applications as a function of space and time. These improvements in nanoparticles research offer unique advantages to develop catalysts with molecular strategies. In order to showcase these advantages of the millifluidic reactors, here we: A. Extensively covered a complete literature review on Lab-on-a-chip devices for gold nanoparticle synthesis and as a catalyst support for continuous …

Constitutive Modeling And Experiments For The Micro And Nano Behaviors In Metals, Cheng Zhang

LSU Doctoral Dissertations

This work addresses the micro- and nano-behaviors in metals through constitutive modeling and experiments. The size effect encountered during nanoindentation experiments, which is known as indentation size effect (ISE), is investigated for metal materials. The ISE is believed to be related with the strain gradient at small indentation depths. Geometrically necessary dislocations (GNDs) are formed in order to accommodate the strain gradient, which results in the increase in the material hardness. The grain boundaries in polycrystalline materials play an important role on the material hardness during nanoindentation experiments as there is a soften-hardening segment in the curve of hardness as …

Developing Co-Current And Counter-Current Spray Drying Computational Fluid Dynamics (Cfd) Simulation Studies To Predict The Quality Of Microencapsulated Fish Oil With Egg White Hydrolysates Powders, Kevin Estuardo Mis Solval

LSU Doctoral Dissertations

Eggs are an excellent source of high quality protein containing all essential amino acids (EAA) including leucine. Food-grade protein hydrolysates can enhance the growth of lactic acid bacteria (LAB). Thermal degradation of bioactives normally occurs during microencapsulation by spray drying. Spray drying modeling using computational tools is essential to engineer new food powders and to minimize and thermal degradation of bioactives. The first chapter of this work discusses the optimization of an enzymatic process in terms of reaction temperature, pH, enzyme:substrate ratio, and reaction time using a response surface methodology (RSM) to produce food-grade protein hydrolysates from egg whites (EWH). …

Risk-Based Wind Loss And Mitigation For Residential Wood Framed Construction, Fatemeh Orooji

LSU Doctoral Dissertations

As a result of increasing windstorm losses in the United States over the past 50 years, a variety of residential wind hazard mitigation methods have been suggested. Mitigation undoubtedly reduces windstorm losses; however, the expected economic risk reduction of mitigation practices over the life of the building depends on the building characteristics (i.e., capacity) and the intensity and occurrence of wind speeds (i.e., demand). Effective decision making requires estimation of potential future losses based on many variables. Many models, primarily mechanics-based simulation models, have been developed to predict building damage from wind events; however; fewer models of economic loss have …

Platinum Hollow Nanospheres With Different Sizes: Controllable Synthesis And Electrocatalytic Oxidation Toward Methanol, Xuan Lin, Mei-Qin Cheng, Zhong-Jin Shang, Ting Xiong, Xian-Tu Zhang, Wei Tian, Jian-Yun Lin, Qi-Ling Zhong, Bin Ren

Journal of Electrochemistry

The selenium (Se) templates and hollow platinum (Pthollow) nanospheres with different sizes were controllably synthesized by adjusting the concentration of sodium dodecyl sulphonate (SDSN) (CSDSN, μmol·L-1) which was used as a surfactant. Accordingly, the Pthollow nanospheres modified glassy carbon (GC) electrode (Pthollow/GC) was prepared. The morphology and composition of Pthollow nanospheres were characterized by scanning electron microscopy (SEM), transmission electron microscope (TEM), energy dispersive X-ray spectroscopy (EDX), high resolution transmission electron microscopy (HRTEM), selected area electron diffraction (SAED) and X-ray diffraction (XRD) techniques. The electrocatalytic activities of Pthollow/GC and electrodeposited Pt nanoparticles modified glassy carbon electrode (Ptnano/GC) toward methanol oxidation …

Comparison In Factors Affecting Electrochemical Properties Of Thermal-Reduced Graphene Oxide For Supercapacitors, Peng Xiao, Da-Hui Wang, Jun-Wei Lang

Journal of Electrochemistry

In this paper, thermal-reduced graphene oxide (T-RGO) materials are synthesized by modified Hummer’s method, followed by thermal reduction under argon atmosphere at different temperatures. Electrochemical investigations show that, for T-RGO electrodes, good electrical conductivity is necessary and the surface functional groups play more significant role than the specific surface area in determining the electrochemical capacitance. The T-RGO obtained at 900 °C (T-RGO900) with a relatively high Brunauer-Emmett-Teller (BET) surface area (314 m²·g^-1) and a high electrical conductivity (2421 S·m^-1) shows a low specific capacitance of 56 F·g^-1. In comparison, the T-RGO obtained …

Nafion/Thionine/Platinum Nanowires-Modified Electrode For Electrocatalyzing Glucose, Yu-Ping Lin, You-Xiu Lin, Qian Zhou, Dian-Ping Tang

Journal of Electrochemistry

A new amperometric biosensor based on Nafion, thionine and latinum nanowires was developed for sensitive detection of glucose. Initially, positively charged thionine molecules were immobilized onto the surface of Nafion-modified glassy carbon electrode through the interaction between -SO₃^- and -NH₃⁺, and glucose oxidase was then assembled on the modified electrode by using platinum nanowires as the cross-linkage. The preparation process was characterized by using cyclic voltammetry. Two enzymatic biosensors modified with and without platinum nanowires were used for the detection of glucose, and the improved analytical properties were obtained with platinum nanowires. Experimental results indicated …