Synthesis And Applications Of Hematite Α-Fe2o3 : A Review, Muhamad Muhajir, Poppy Puspitasari, Jeefferie Abdul Razak

Journal of Mechanical Engineering Science and Technology (JMEST)

This article reviewed the hematite α-Fe2O3. It focuses on its material properties, nanostructures, synthesis techniques, and its numerous applications. Researchers prepared the hematite nanostructure using the synthesis methods such as hydrothermal, and, further, enhanced it by improving the techniques to accommodate the best performance for specific applications and to explore new applications of hematite in humidity sensing.

Failure Analysis On Titen Proto-Xx Car Chassis, Gaguk Jatisukamto, Rika Dwi Hidayatul Qoryah, Santoso Mulyadi

Journal of Mechanical Engineering Science and Technology (JMEST)

The car chassis as a skeleton supports all loads and is the most important component. Car chassis requirements must be rigid, twisting resistant, vibration resistant and resistant to fatigue. This study aims to find the cause of the failure of the Titen Proto-XX car chassis connection. The research methodology was conducted by testing the composition of materials and structural analysis using Ansys Workbench Release 15.0 software. The conclusion of the research is that the skeletal structure material uses Aluminum AA series 1XXX with Al content greater than 99.5%, the welding ability is low, causing a failure in the welded joint. …

The Effect Of Chlorophyll Concentration From Papaya Leaves On The Performance Of Dye-Sensitized Solar Cell, Dede Rizali, Heru Suryanto, Sukarni Sukarni

Journal of Mechanical Engineering Science and Technology (JMEST)

Dye-Sensitized Solar Cell (DSSC) is the third generation solar cell that has sandwich structure consisted of organic dye material and other components such as titanium dioxide (TiO2) semiconductor, electrolyte, and substrates (counter electrode and working electrode). The dye in the device was made from green plant chlorophyll such as papaya. This research aimed to find the influence of dye concentration from papaya leaves chlorophyll on the performance of DSCC. The discussion covered the output power (Pout), Fill Factor (FF), and efficiency (ɳ). The method in this research was explorative experimental with independent variables such as direct and indirect sunlight. The …

Multi-Resonant Feedback Control Of Multiple Degree-Of-Freedom Wave Energy Converters, Ossama Abdelkhalik, Shangyan Zou, Rush D. Robinett Iii, David G. Wilson, Giorgio Bacelli, Ryan G. Coe, Umesh Korde

Michigan Tech Patents

Multi-resonant control of a 3 degree-of-freedom (heave-pitch-surge) wave energy converter enables energy capture that can be in the order of three times the energy capture of a heave-only wave energy converter. The invention uses a time domain feedback control strategy that is optimal based on the criteria of complex conjugate control. The multi-resonant control can also be used to shift the harvested energy from one of the coupled modes to another, enabling the elimination of one of the actuators otherwise required in a 3 degree-of-freedom wave energy converter. This feedback control strategy does not require wave prediction; it only requires …

Multi-Scale Modeling Of The Lamellar Unit Of Arterial Media, Hozhabr Mozafari, Lulu Wang, Yuguo Lei, Linxia Gu

Department of Mechanical and Materials Engineering: Faculty Publications

The heterogeneity of the lamellar unit (LU) of arterial media plays an important role in the biomechanics of artery. Current two-component (fibrous component and a homogenous matrix) constitutive model is inappropriate for capturing the micro-structural variations in the LU, such as contraction/relaxation of vascular smooth muscle cells (VSMCs), fragmentation of the elastin layer, and deposition/disruption of the collagen network. In this work, we developed a representative volume element (RVE) model with detailed micro-configurations, i.e., VSMCs at various phenotypes, collagen fibers, and elastin laminate embedded in the ground substance. The fiber architecture was generated based on its volume fraction and orientations. …

Development Of Mbd Model And Analysis Methodology For Vehicle Design, Alfonso Christopher Ponce

Mechanical Engineering ETDs

This thesis is to provide a new methodology that considers the effects the chassis applies during dynamic load to the suspension and the handling characteristics of a road course vehicle. A methodology in which is described in detail as well as an applied demonstration where literature before this thesis, lacks in replication and serves to establish a basis for multi-body dynamic analysis in this area. Two models to be created, rigid and flexible, and to compare each other to study the effects the chassis torsional stiffness has during load transfer. Ultimately, to assist in the design of a vehicle that …

Development Of Engineered Cementitious Composites With Conductive Inclusions For Use In Self-Sensing Applications, Benny Suryanto Dr, Danah Saraireh Ms, Steven Walls Mr, Jaehwan Kim Dr, W John Mccarter Prof

International Conference on Durability of Concrete Structures

The mechanical and a.c. electrical properties of a new varietal of engineered cementitious composite (ECC) incorporating conductive inclusions are presented. Electrical measurements were undertaken over a wide frequency range while curing and when under uniaxial tensile loading to study the influence of ongoing hydration and multiple microcrack formation on the composite electrical impedance. When presented in Nyquist format, the work shows that conductive inclusions reduce the bulk resistance of the composite while enhancing its polarizability, transforming the classic, single-arc bulk response of typical cement-based materials to a two-arc response. The bulk resistance was shown to increase with time and damage, …

Load-Bearing Capacity Of Corroded Reinforced Concrete Structures Caused By Carbonation And Exposed To Xc4, Esko Sistonen

International Conference on Durability of Concrete Structures

Concrete corrosion can be visualized as a combination of chemical reaction on concrete and electrochemical reaction on steel reinforcement. Failure of steel reinforcement due to corrosion can inflict significant stress on concrete during load distribution. As such, it is necessary to analyse the long-term effects of corrosion on the load bearing capacity and bending strength of steel reinforcement. This research investigated the mechanical and electrochemical properties of concrete exposed to long-term corrosion for a period of 16 years. Non-destructive testing like crack width measurements, visual examination, electrochemical measurements using Galva Pulse and determination of average chloride content were undertaken to …

Experimental And Numerical Investigation On The Irregularity Of Carbonation Depth Of Concrete Under Supercritical Condition, Hao Bao Masc, Min Yu Dr., Jianqiao Ye Dr., Lihua Xu Dr., Yin Chi Dr., J Ye

International Conference on Durability of Concrete Structures

The heterogeneity of a cement-based material results in a random spatial distribution of carbonation depth, which may significantly affect the mechanical properties and durability of the material. Currently, there is a lack of both experimental and numerical investigations aiming at a statistical understanding of this important phenomenon. This paper presents both experimental and numerical supercritical carbonation test results of concrete blocks. The random fields of porosity and two-dimension random aggregate model of concrete were proposed for the simulation. The carbonation depths are measured and distributed along the carbonation boundary by the proposed rapid image processing technique, which are then statistically …

Alkali Reactive Carbonate Rocks: Is It Alkali Silica Reaction (Asr) Or Alkali Carbonate Reaction (Acr)?, Mengesha Beyene, Rc Meininger

International Conference on Durability of Concrete Structures

The root cause of distress in two different concrete structures made from carbonate coarse aggregates that fit the textural and compositional criteria cited for ACR was found to be caused by ASR, not ACR. Stereo-optical examination and transmitted polarized light microscopy (PLM) analysis showed that the concretes contain some dark gray, fine-grained argillaceous dolomitic coarse aggregates in which secondary white deposit filling the cracks extending from these aggregates into the paste (as well as lining air voids) is ASR gel. Back scattered electron (BSE) imaging with EDS spectra and x-ray elemental mappings, clearly confirm that the white secondary deposits consist …

Factors Influencing Retirement Decision Making For Louisiana State Government Employees, Osama A. Amous

LSU Doctoral Dissertations

ABSTRACT

Public pension members continually face factors affecting their decision to retire in the changing American society. Workers are living longer and need more medical care with better retirement benefits. For Louisiana public employees specifically, no prior studies have examined the factors affecting workers’ decision to retire nor evaluated the factors impacting workers’ decision.

This multiphase study aimed to identify factors and evaluate the decision-making process that enables Louisianans to retire happily and satisfied with a guaranteed income, and to examine millennials’ decision-making process. In the initial phase, ten active and retired male and female participants answered questions in-person, leading …

Three-Dimensional Porous Vn Octahedron Catalyst With High Electrocatalytic Efficiency Toward Hydrogen Evolution Reaction, Can Yin, Wei-Wei Fu, Ling Fang, Shi-Li You, Hui-Juan Zhang, Yu Wang

Journal of Electrochemistry

With the rapid development of China’s economy, the demand for energy is increasing, and environmental problems are becoming more and more serious. The development and utilization of highly-clean new energy fuel can effectively alleviate the energy crisis and environmental pollution. Nowadays, exploring high-efficiency, environment-friendly and low-cost catalysts remains the focus of research in the hydrogen evolution reaction (HER). In this research, firstly, we proposed a three-dimensional porous vanadium nitride (VN) with octahedral structure, which was prepared by a calcination treatment method. The VN catalyst showed a good electrocatalytic activity toward HER, involving a small overpotential of 94.0 mV at -10 …

Influences Of Morphology And Nitrogen Doping On The Electrocatalytic Characteristics For Oxygen Reduction Reaction Of Nio/Rgo, Dong Liang, Heng-Yi Fang, Shuo Yao, Jie-Mei Yu, Zhao-Liang Zhang, Zhan-Kun Jiang, Xue-Ping Gao, Tai-Zhong Huang

Journal of Electrochemistry

In this research, the reduced graphene oxide (rGO) supported sheet-like NiO (NiO/rGO) and spherical-like NiO (NiO/N-rGO) catalysts for oxygen reduction reaction (ORR) were prepared. The structures, morphologies and chemical states of the two catalysts were characterized by X-ray diffraction (XRD), Raman spectroscopy, X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The electrochemical catalytic performance of the two catalysts for ORR were investigated by cyclic voltammetry (CV), Tafel, linear sweeping voltammetry (LSV), rotating disc electrode (RDE) and rotating ring disc electrode (RRDE) tests. Electrochemical results showed that the current density and onset potential (about 0.89 V) …

Preparation Of Nanostructural Mno-Porous Graphene Hybrid Material By Thermally-Driven Etching Of Mno For Lithium-Air Batteries, Juan Yang, Jun-Wei Lang, Peng Zhang, Bao Liu

Journal of Electrochemistry

In this paper, improving the surface morphology of graphene(GNSs) as designed concept. we describe a MnO/porous-graphene(MnO-PGNSs) was synthesized by a simple site-localized Mn²⁺ on GO (Mn-GO) by charge adsorption and then driving by high-temperature calcination, growing MnO nanoparticles and etching GNSs achieved on step. And Then focus on the key factors of influenced the etch hole formation are analyzed, founded the dispersion of Mn-GO; layer number of GO and calcination temperature also affected the formation of holes. In addition, the MnO-PGNSs as lithium-air battery cathode exhibits high reversible capacity compared with GNSs and PGNs and it is able to …

Special Issue: Electrocatalysis And Fuel Cells, Shuangyin Wang

Journal of Electrochemistry

/

A Facile Route To Synthesize Pt-Wo3 Nanosheets With Enhanced Electrochemical Performance For Her, Peng-Jie Jiang, Yi Lv, Chang-Miao Chen, Hong-Cheng He, Yong Cai, Ming Zhang

Journal of Electrochemistry

Platinum-tungsten trioxide (Pt-WO₃) nanosheets were synthesized on nickel foams (NFs) directly. As great conductive networks, NFs substrates could greatly improve the electrode performance of WO₃. The modified platinum nanoparticles not only enhanced the electron transformation of catalysts, but also increased the active sites for hydrogen evolution reaction (HER). Pt-WO₃/NF revealed a better catalytic activity than WO₃/NFs with a smaller Tafel slope (80 mV·dec^-1) and a lower overpotential of 72 mV at the current density of 10 mA·cm^-2. In addition, Pt-WO₃/NF showed great durability and stability during …

Nickel Selenide Derived From [Ni(En)3](Seo3) Complex For Efficient Electrocatalytic Overall Water Splitting, Dan-Dan Chen, Xue-Qing Gao, Hong-Fei Liu, Wei Zhang, Rui Cao

Journal of Electrochemistry

Electrocatalytic water splitting is considered as a promising technology for renewable energy. The development of efficient, stable, cost-effective, and bifunctional catalysts for both water reduction and oxidation has continued to face significant challenges. Herein, we report a robust and highly active nickel selenide (NiSe) spheres grown on carbon cloth (CC) by electrodeposition from a nickel selenite complex which is a single source containing both Ni and Se. A combination of two chemicals containing, separately, Ni and Se is used in traditional preparations of metal selenides, causing possible problems in the uniformity of the products. The as-prepared NiSe-EA/CC electrode exhibited electrocatalytic …

Pd Nanoparticles Supported On The Etched Ni Foams As High-Performance Electrocatalysts For Direct Ethanol Fuel Cells, Chi Zhang, Cheng-Fei Li, Gao-Ren Li

Journal of Electrochemistry

The development of non-Pt anode electrocatalysts with high activity and long-term durability at low cost for fuel cells still remains enormous challenge. Here we report the Pd nanoparticles supported on Ni foams etched by the mixed acids (HNO₃+H₂SO₄+H₃PO₄+CH₃COOH) (Pd/ME-NF) that are designed and fabricated as high-performance electrocatalysts for ethanol oxidation in alkaline media. Because of the advantages of large open space, fast electrolyte penetration/diffusion and rapid electron transfer process, the Pd/ME-NF catalysts exhibited significantly improved electrocatalytic activity and durability compared with the commercial Pd/C catalysts.

Investigations In Electrochemical Thermodynamic And Kinetic Properties Of As-Cast And As-Quenched Cemg10Ni2 Hydrogen Storage Alloys, Feng Hu, Li-Rong Luo, Yong-Zhi Li, Ting-Ting Zhai, Xin Zhao, Yang-Huan Zhang

Journal of Electrochemistry

In order to improve the electrochemical hydrogen storage properties of CeMg₁₀Ni₂ alloy, the rapid quenching technology was used to prepare CeMg₁₀Ni₂ alloys with nano-crystalline and amorphous structure. The microstructures of as-cast and as-spinning sample were characterized by X-ray diffraction (XRD) and transmission electron microscopy (TEM). The electrochemical hydrogen storage properties were investigated by an automatic galvanostatic charging/discharging, high rate discharging (HRD), electrochemical impedance spectroscopy (EIS) and potentiodynamic polarization techniques. The results revealed that the as-cast alloy was composed of multiphase structures. The as-quenched alloys were made up of nano-crystalline and/or amorphous structures, and the …

Investigating Nano-Coated Surfaces In Improvement Wear Resistance Of Tillage Tools, Saeed Mehrang Marani, Gholamhossein Shahgholi, Saeed Kanoon Marani

Emirates Journal for Engineering Research

The blade in the tillage operation has the most interaction with soil particles. It causes the wear and tear of this piece and reduces its expected life span. Tillage tool wear is of great importance to farmers in terms of economic aspects, reduced quality tillage operations, and increased power consumption. The aim of this study is to investigate wearing of five materials including st37 steel (SST37) plate, galvanized steel (GAS), and fiberglass (GFRP), and two coatings (i.e., titanium nano-nitride (nano-TiN) and tantalum carbide (nano-TaC)) by sputtering in the plasma medium of the layer based on conventional steel. These pieces were …

Relating Individual Characteristics And Task Complexity To Performance Effectiveness In Individual And Collaborative Problem Solving, Kaveh Sheikhrezaei

LSU Doctoral Dissertations

The objective of this research is to examine the variables that influence performance effectiveness on individual and collaborative problem solving. The last few years have seen renewed interest in how team member personal characteristics and team composition characteristics impact team effectiveness.

Even with a growing quantity of organizations performing jobs by using groups, little is understood how people included in a team impact intragroup interaction and results. Most research investigates group’s performance based on a single characteristic which causes much confusion and contradictory results of the variables that impact overall group performance. Most research typically does not analyze the composition …

Beyond The Toolpath: Site-Specific Melt Pool Size Control Enables Printing Of Extra-Toolpath Geometry In Laserwire-Based Directed Energy Deposition, Brian T. Gibson, Bradley S. Richardson, Tayler W. Undermann, Lonnie J. Love

Department of Mechanical and Materials Engineering: Faculty Publications

A variety of techniques have been utilized in metal additive manufacturing (AM) for melt pool size management, including modeling and feed-forward approaches. In a few cases, closed-loop control has been demonstrated. In this research, closed-loop melt pool size control for large-scale, laser wire-based directed energy deposition is demonstrated with a novel modification, i.e., site-specific changes to the controller setpoint were commanded at trigger points, the locations of which were generated by the projection of a secondary geometry onto the primary three-dimensional (3D) printed component geometry. The present work shows that, through this technique, it is possible to print a specific …

Effect Of Silica Fume In Concrete On Mechanical Properties And Dynamic Behaviors Under Impact Loading, Shijun Zhao, Qing Zhang

Department of Mechanical and Materials Engineering: Faculty Publications

The effect of silica fume (SF) in concrete on mechanical properties and dynamic behaviors was experimentally studied by split Hopkinson pressure bar (SHPB) device with pulse shaping technique. Three series of concrete with 0, 12%, and 16% SF as a cement replacement by weight were produced firstly. Then the experimental procedure for dynamic tests of concrete specimens with SF under a high loading rate was presented. Considering the mechanical performance and behaviors of the concrete mixtures, those tests were conducted under five different impact velocities. The experimental results clearly show concrete with different levels of SF is a strain-rate sensitive …

System And Method For Sensing Wind Flow Passing Over Complex Terrain, Saleh Nabi, Piyush Grover, Mithu Debnath

Department of Mechanical and Materials Engineering: Faculty Publications

A wind flow sensing system determines a first approximation of the velocity field at each of the altitudes by simulating computational fluid dynamics ( CFD ) of the wind flow with operating parameters reducing a cost function of a weighted combination of errors , determines a horizontal derivative of vertical velocity at each of the altitudes from the first approximation of the velocity fields , and determines a second approximation of the velocity fields using geometric relationships between a velocity field for each of the altitudes , projections of the measurements of radial velocities on the three - dimensional axes …

Multi-Resonant Feedback Control Of A Single Degree-Of-Freedom Wave Energy Converter, David G. Wilson, Rush D. Robinett Iii, Ossama Abdelkhalik, Jiajun Song, Giorgio Bacelli

Michigan Tech Patents

A multi-resonant wide band controller decomposes the wave energy converter control problem into sub-problems; an independent single-frequency controller is used for each sub-problem. Thus, each sub-problem controller can be optimized independently. The feedback control enables actual time-domain realization of multi-frequency complex conjugate control. The feedback strategy requires only measurements of the buoy position and velocity. No knowledge of excitation force, wave measurements, nor wave prediction is needed. As an example, the feedback signal processing can be carried out using Fast Fourier Transform with Hanning windows and optimization of amplitudes and phases. Given that the output signal is decomposed into individual …

Model Predictive Control Of Parametric Excited Pitch-Surge Modes In Wave Energy Converters, Ossama Abdelkhalik, Rush D. Robinett Iii, Shangyan Zou, David G. Wilson, Giorgio Bacelli, Umesh Korde, Ryan G. Coe

Michigan Tech Patents

A parametric excitation dynamic model is used for a three degrees-of-freedom (3-DOF) wave energy converter. Since the heave motion is uncoupled from the pitch and surge modes, the pitch-surge equations of motion can be treated as a linear time varying system, or a linear system with parametric excitation. In such case the parametric exciting frequency can be tuned to twice the natural frequency of the system for higher energy harvesting. A parametric excited 3-DOF wave energy converter can harvest more power, for both regular and irregular waves, compared to the linear 3-DOF. For example, in a Bretschneider wave, the harvested …

Multi-Agent Control System And Method, Piyush Grover, Karthik Elamvazhuthi

Department of Mechanical and Materials Engineering: Faculty Publications

Motion of multiple agents with identical non - linear dynamics is controlled to change density of the agents from the initial to the final density . A first control problem is formulated for optimizing a control cost of changing density of the agents from the initial density to the final density subject to dynamics of the agents in a density space . The first control problem , which is a non - linear non - convex problem over a multi - agent control and a density of the agents , is trans formed into a second control problem over the …

Modelling The Addition Of Limestone In Cement Using Hydcem, Niall Holmes, Denis Kelliher, Mark Tyrer

Conference papers

Hydration models can aid in the prediction, understanding and description of hydration behaviour over time as the move towards more sustainable cements continues.

HYDCEM is a new model to predict the phase assemblage, degree of hydration and heat release over time for cements undergoing hydration for any w/c ratio and curing temperatures up to 450C. HYDCEM, written in MATLAB, complements more sophisticated thermodynamic models by predicting these properties over time using user-friendly inputs within one code. A number of functions and methods based on up to date cement hydration behaviour from the literature are hard-wired into the code along with …

3d Printing Of Silk Fibroin-Based Hybrid Scaffold Treated With Platelet Rich Plasma For Bone Tissue Engineering, Liang Wei, Shaohua Wu, Mitchell Kuss, Xiping Jiang, Runjun Sun, Reid Patrick, Xiaohong Qin, Bin Duan

Department of Mechanical and Materials Engineering: Faculty Publications

3D printing/bioprinting are promising techniques to fabricate scaffolds with well controlled and patient-specific structures and architectures for bone tissue engineering. In this study, we developed a composite bioink consisting of silk fibroin (SF), gelatin (GEL), hyaluronic acid (HA), and tricalcium phosphate (TCP) and 3D bioprinted the silk fibroin-based hybrid scaffolds. The 3D bioprinted scaffolds with dual crosslinking were further treated with human platelet-rich plasma (PRP) to generate PRP coated scaffolds. Live/Dead and MTT assays demonstrated that PRP treatment could obviously promote the cell growth and proliferation of human adipose derived mesenchymal stem cells (HADMSC). In addition, the treatment of PRP …

3d Printing Of Silk Fibroin-Based Hybrid Scaffold Treated With Platelet Rich Plasma For Bone Tissue Engineering, Liang Wei, Shaohua Wu, Mitchell Kuss, Xiping Jiang, Runjun Sun, Reid Patrick, Xiaohong Qin, Bin Duan

Department of Mechanical and Materials Engineering: Faculty Publications

3D printing/bioprinting are promising techniques to fabricate scaffolds with well controlled and patient-specific structures and architectures for bone tissue engineering. In this study, we developed a composite bioink consisting of silk fibroin (SF), gelatin (GEL), hyaluronic acid (HA), and tricalcium phosphate (TCP) and 3D bioprinted the silk fibroin-based hybrid scaffolds. The 3D bioprinted scaffolds with dual crosslinking were further treated with human platelet-rich plasma (PRP) to generate PRP coated scaffolds. Live/Dead and MTT assays demonstrated that PRP treatment could obviously promote the cell growth and proliferation of human adipose derived mesenchymal stem cells (HADMSC). In addition, the treatment of PRP …