Engineering Commons^™

Waste Plastic Direct Extrusion Hangprinter, Aliaksei Petsiuk, Bharath Lavu, Rachel Dick, Joshua M. Pearce

Michigan Tech Publications, Part 1

As the additive manufacturing industry grows, it is compounding the global plastic waste problem. Distributed recycling and additive manufacturing (DRAM) offers an economic solution to this challenge, but it has been relegated to either small-volume 3D printers (limiting waste recycling throughput) or expensive industrial machines (limiting accessibility and lateral scaling). To overcome these challenges, this paper provides proof-of-concept for a novel, open-source hybrid 3D printer that combines a low-cost hanging printer design with a compression-screw-based end-effector that allows for the direct extrusion of recycled plastic waste in large expandable printing volumes. Mechanical testing of the resultant prints from 100% waste …

Comparative Study Of Tapered Versus Conventional Cylindrical Balloon For Stent Implantation In Stenotic Tapered Artery, Xiang Shen, Jiabao Jiang, Hongfei Zhu, Kaikai Lu, Pengfei Dong, Linxia Gu

Department of Mechanical and Materials Engineering: Faculty Publications

The natural tapering of coronary arteries often creates a dilemma for optimal balloon sizing during stenting. The influence of different balloon types, namely, a tapered balloon and a conventional cylindrical balloon, on the mechanical performance of the stent as well as arterial mechanics was investigated via the finite element method. Stent free-expansion and stent deployment in a stenotic tapered artery were investigated numerically. The biomechanical behavior of the two balloon types was compared in terms of stent foreshortening, stent deformation, stent stress distribution, and arterial wall stress distribution. Results indicate that balloon types affect the transient behavior of the stent …

Three-Dimensional Printed Abdominal Imaging Windows For In Vivo Imaging Of Deep-Lying Tissues, Mitchell Kuss, Ayrianne J. Crawford, Olawale A. Alimi, Michael A. Hollingsworth, Bin Duan

Department of Mechanical and Materials Engineering: Faculty Publications

The ability to microscopically image diseased or damaged tissue throughout a longitudinal study in living mice would provide more insight into disease progression than having just a couple of time points to study. In vivo disease development and monitoring provides more insight than in vitro studies as well. In this study, we developed permanent 3D-printed, surgically implantable abdominal imaging windows (AIWs) to allow for longitudinal imaging of deep-lying tissues or organs in the abdominal cavity of living mice. They are designed to prevent organ movement while allowing the animal to behave normally throughout longitudinal studies. The AIW also acts as …

Synthesis And Consolidation Of Metal Oxide Nanocrystals Via Nonthermal Plasma, Austin Cendejas

McKelvey School of Engineering Graduate Student Theses & Dissertations

Nonthermal plasmas offer a unique nonequilibrium environment that has been leveraged in a wide variety of applications in the fields of material processing, lighting, and waste management to name a few. In all of these cases, the plasma serves as a source of high energy electrons, ions, reactive gas species, and radicals that interact in several ways with surfaces brought into contact with the plasma. Specifically, nonthermal plasmas have been shown to be very successful in achieving continuous, high-throughput, monodisperse nanocrystals of a wide variety of materials. The crystallinity of nanoparticles synthesized in nonthermal plasmas can be attributed to the …

Modeling The Effects Of Mechanical Loading On Hypertrophic Cardiomyopathy Pathogenesis In Human Induced Pluripotent Stem Cell Derived Micro Heart Muscle, Jingxuan Guo

McKelvey School of Engineering Graduate Student Theses & Dissertations

Sudden cardiac death in the young is devastating. Advances in genetics have associated mutations in the contractile sarcomere apparatus of cardiomyocytes with hypertrophic cardiomyopathy, the most frequent cause of sudden cardiac death in the young. Currently, it is challenging to predict genotype-phenotype relationships in hypertrophic cardiomyopathy due to its incomplete disease penetrance. For example, different patients from the same family with identical genomic variants develop different symptoms. Non-genetic, environmental factors such as blood pressure are critical in heart function and disease. Therefore, understanding how mechanical factors contribute to phenotypes in diseases like hypertrophic cardiomyopathy is critical for developing effective therapeutics. …

Plasmonic Nanomaterials-Based Point-Of-Care Biosensors, Rohit Gupta

McKelvey School of Engineering Graduate Student Theses & Dissertations

Point-of-care (POC) biosensors, although rapid and easy-to-use, are orders magnitude less sensitive than laboratory-based tests. Further they are plagued by poor stability of recognition element thus limiting its widespread applicability in resource-limited settings. Therefore, there is a critical need for realizing stable POC biosensors with sensitivity comparable to gold-standard laboratory-based tests. This challenge constitutes the fundamental basis of this dissertation work– to expand access to quality and accurate biodiagnostic tools. At the heart of these solutions lies plasmonic nanoparticles which exhibit unique optical properties which are attractive for label-free and labelled biosensors.Firstly, we improve the stability and applicability of label-free …

Design Of Multi-Principal Element Materials Using A Combination Of First-Principles Calculations And Machine Learning, Zhaohan Zhang

McKelvey School of Engineering Graduate Student Theses & Dissertations

Multiple-principal element materials, including alloys (MPEAs), oxides and other compounds combine several elements on a sub-lattice, which increases the configurational entropy and contributes to their thermodynamic stability. The vast combinatorial design space of multi-principal element materials gives rise to diverse microstructures and unprecedent combination of properties. It also poses a challenge—how to rapidly screen MPEAs with stability and properties for targeted applications. Furthermore, fundamental composition-structure-property relationships in MPEAs are currently missing. In this dissertation, I have used MPEAs as a representative system and investigated the role of chemical composition on their phase-stability and mechanical properties. With a combination of first-principles …

The Generation And Transport Of Charged Aerosols: Fundamental Study And Applications In Medicine And Energy Conversion, Hao Zhou

McKelvey School of Engineering Graduate Student Theses & Dissertations

Charged aerosols have significant implications in the field of functional material synthesis, pharmaceutical coating, and drug delivery. Electrospray systems are an effective methodology for generating highly charged monodispersed droplets in the size range from nanometer to micrometer. The prediction of surface charge, size and morphology of nanoparticles resulting from charged droplets are highly required for the precise control of nanoparticle properties and their effective utilization. However, the evolution of charged droplet is not well understood due to the existence of coulombic fission and ion evaporation processes. Thus, the goal of this dissertation is to elucidate how the precursor properties and …

Soft Electronics And Sensors For Wearable Healthcare Applications, Li-Wei Lo

McKelvey School of Engineering Graduate Student Theses & Dissertations

Wearable electronics are becoming increasingly essential to personalized medicine by collecting and analyzing massive amounts of biological signals from internal organs, muscles, and blood vessels. Conventional rigid electronics may lead to motion artifacts and errors in collected data due to the mismatches in mechanical properties between human skin. Instead, soft wearable electronics provide a better platform and interface that can form intimate contact and conformably adapt to human skin. In this respect, this thesis focuses on new materials formulation, fabrication, characterization of low-cost, high sensitivity and reliable sensors for wearable health monitoring applications.

More specifically, we have studied the silver …

Testing Oxygenated Microbubbles Via Intraperitoneal And Intrathoracic Routes On A Large Pig Model Of Lps-Induced Acute Respiratory Distress Syndrome, Riaz Ur Rehman Mohammed, Nathaniel T. Zollinger, Andrea R. Mccain, Roser Romaguera-Matas, Seth P. Harris, Keely L. Buesing, Mark A. Borden, Benjamin S. Terry

Department of Mechanical and Materials Engineering: Faculty Publications

With a mortality rate of 46% before the onset of COVID-19, acute respiratory distress syndrome (ARDS) affected 200,000 people in the US, causing 75,000 deaths. Mortality rates in COVID-19 ARDS patients are currently at 39%. Extrapulmonary support for ARDS aims to supplement mechanical ventilation by providing life-sustaining oxygen to the patient. A new rapid-onset, human-sized pig ARDS model in a porcine intensive care unit (ICU) was developed. The pigs were nebulized intratracheally with a high dose (4 mg/kg) of the endotoxin lipopolysaccharide (LPS) over a 2 h duration to induce rapid-onset moderate-to- severe ARDS. They were then catheterized to monitor …

Vibrating Flexoelectric Micro-Beams As Angular Rate Sensors, Yilin Qu, Feng Jin, Jiashi S. Yang

Department of Mechanical and Materials Engineering: Faculty Publications

We studied flexoelectrically excited/detected bending vibrations in perpendicular directions of a micro-beam spinning about its axis. A set of one-dimensional equations was derived and used in a theoretical analysis. It is shown that the Coriolis effect associated with the spin produces an electrical output proportional to the angular rate of the spin when it is small. Thus, the beam can be used as a gyroscope for angular rate sensing. Compared to conventional piezoelectric beam gyroscopes, the flexoelectric beam proposed and analyzed has a simpler structure.

Vibrating Flexoelectric Micro-Beams As Angular Rate Sensors, Yilin Qu, Feng Jin, Jiashi S. Yang

Department of Mechanical and Materials Engineering: Faculty Publications

We studied flexoelectrically excited/detected bending vibrations in perpendicular directions of a micro-beam spinning about its axis. A set of one-dimensional equations was derived and used in a theoretical analysis. It is shown that the Coriolis effect associated with the spin produces an electrical output proportional to the angular rate of the spin when it is small. Thus, the beam can be used as a gyroscope for angular rate sensing. Compared to conventional piezoelectric beam gyroscopes, the flexoelectric beam proposed and analyzed has a simpler structure.

Geometric Analysis Of Insect Wing Vein Network, Jacob White, Ying Hu, Sangjin Ryu, Seunghee Kim, Haipeng Zhang

Department of Mechanical and Materials Engineering: Faculty Publications

An insect wing consists of a thin membrane supported by a system of veins, and flow of blood through the system of veins is critical for maintaining healthy insect wings. Better understanding of the insect wing vein circulation requires to know how the efficiency of blood flow in an insect wing relates to the geometric shape of the vein. Our investigation of the wing vein network of a dragonfly Anax junius follows the idea of Murray’s law, which is established in the study of efficiency of the vein network and the geometric shape of the vein. Instead of using the …

Pressure-Induced Phase Transition And Electronic Structure Changes In Equiatomic Fev, Homero Reyes Pulido

Open Access Theses & Dissertations

Classical molecular dynamics methods can accurately describe a broad set of many-atomssystems. Although more economical, the results given by this framework lack the precision capable of density functional theory (DFT). Therefore, the structural stability of the B2 phase of a body-centered-cubic iron-vanadium (FeV) alloy using DFT on the electronic structure level is analyzed to verify and further explain classical results obtained by our group in this same alloy. Using Quantum Espresso and Phonopy for the computational simulations, the plotted band structure, electronic density of states (eDOS), phonon dispersions, charge density, and Fermi surfaces for various compressed unit cells are presented. …

Study Of Thermoelectric And Lattice Dynamics Properties Of 2d Layered Mx (M = Sn, Pb; X = S, Se, Te) And Zrs2 Compounds Using First-Principles Approach, Abhiyan Pandit

Graduate Theses and Dissertations

The aim of this dissertation is the investigation of thermoelectric and lattice dynamics properties of two-dimensional (2D) MX (M = Sn, Pb; X = S, Se, Te) and ZrS2 compounds based on the first-principles density functional theory. The dimensionality reduction (e.g., using 2D structure) of bulk materials is found to have enhanced thermoelectric efficiency. This enhancement is attributed to the increase of the Seebeck coefficient as a result of higher electronic density of states near the Fermi level in low-dimensional materials. In addition, lowering the dimensionality increases phonon scattering near interfaces and surfaces in 2D materials, which leads to a …

Etching Process Development For Sic Cmos, Weston Reed Renfrow

Graduate Theses and Dissertations

Silicon Carbide (SiC) is an exciting material that is growing in popularity for having qualities that make it a helpful semiconductor in extreme environments where silicon devices fail. The development of a SiC CMOS is in its infancy. There are many improvements that need to be made to develop this technology further. Photolithography is the most significant bottleneck in the etching process; it was studied and improved upon. Etching SiC can be a challenge with its reinforced crystal structure. Chlorine-based inductively coupled plasma (ICP) etching of intrinsic SiC and doped SiC, SiO2, and Silicon has been studied. A baseline chlorine …

Characterization Of 3d Stereolithography (Sla) Printed Polymer For Autonomous-Flow Microfluidic Devices, Michelle Gamboa

Open Access Theses & Dissertations

3D Stereolithography (SLA) printing is a high-throughput, precise and reproducible manufacturing platform which makes it a desirable technique to develop microfluidic devices for bioanalytical applications. However, limited information exists regarding the physical, chemical, and biological properties of the polymer resins used in 3D SLA printing. This project demonstrates the characterization of a commercially available 3D SLA printed resin polymer used to develop an autonomous-flow (self-driven) microfluidic device. In this investigation, time-dependent materials characterization was done on the Formlabs clear V4 resin to observe changes in mechanical and surface properties. The clear, printed polymer was analyzed with attenuated total reflectance (ATR), …

Reflectance Spectral Characterization And Taxonomy Applications Of Spacecraft Materials To Aid Space Situational Awareness, Jacqueline Andrea Reyes

Open Access Theses & Dissertations

The increasing number of space missions involving successfully deployed spacecraft have resulted in an augmented density of artificial objects positioned in orbital domains near Earth. With this steady accumulation of objects in space, it has become increasingly imperative to characterize spacecraft materials, which may ultimately be contributors to the orbital debris population. In an effort to identify unique material-specific spectroscopic markers, a variety of spacecraft materials frequently utilized in the aerospace industry to construct typical spacecraft were analyzed using reflectance spectroscopy as a characterization technique for assessment on material type according to optical features. This is significant in providing information …

Additive Manufacturing Of Aluminum Alloy By Metal Fused Filament Fabrication (Mf3)., Luke J. Malone

Electronic Theses and Dissertations

This research studies metal-fused filament fabrication (MF3) for manufacturing aluminum alloy parts. An aluminum alloy powder-based feedstock with a polymer-binder system was extruded via capillary rheometry to form a filament. The filament was used to print green parts that were involved in a two-step debinding process combining solvent and thermal extraction of the polymer binder, then sintered in a partial vacuum. Resulting grain structure, sintered density, and mechanical properties will be characterized and compared to metal injection molded (MIM) specimens. The main objective is to gain an understanding of the MF3 process characteristics and the ensuing material properties and microstructure …

Crack Control And Bond Performance Of Alternative Coated Reinforcements In Concrete, Sachin Sreedhara

All Dissertations

Concrete cracking in structures is a ubiquitous problem which can lead to the deterioration of the structure. Other than affecting the strength aspect of a structure, cracking impacts the serviceability criteria as well. Although cracking phenomenon in any structure is highly inevitable, it has to be minimized in order to maintain a structure’s life effectively. Cracking in reinforced concrete structures is related to the bond strength developed between the bar and the concrete. It also depends on an ability of the bar to resist the stresses due to shrinkage to minimize the crack. Another important aspect is the resistance offered …

Passive Prosthetic Ankle Design Based On Indonesian Anthropometry, Wahyu Dwi Lestari

Journal of Mechanical Engineering Science and Technology (JMEST)

Foot prosthesis is a replacement for the foot to overcome activity limitations due to disease, birth defects, accidents, or amputations. Many foot prosthetics have been developed in recent years to treat patients. However, prostheses on the market today have drawbacks, including their high price, lack of comfort, stiff ankles, and low durability. The main objective of this study is to develop an existing ankle-foot prosthesis design that approximates the resemblance of a human foot according to the anthropometry of Asians, especially Indonesians. This study contains the design of a prosthetic foot with a skin design model and a support core. …

Surface Quality Of Fe, Ni And Cr Added Hyper-Eutectic Al-Si Automotive Alloys Under Up-Milling And Down-Milling Operation, Akib Abdullah Khan, Mashiur Rahman Shoummo, Mohammad Salim Kaiser

Journal of Mechanical Engineering Science and Technology (JMEST)

Effect of the elements Fe, Ni, and Cr on the surface quality under machining of hyper-eutectic aluminiumbased Al-Si automotive alloys has been carried out as the elements improve the properties of this alloy. Machining is done on a horizontal type milling machine using a high-speed steel slab milling cutter in dry condition. Only the cutting speed varies throughout the experiment, while the machining feed and depth of cut remain fixed. The experimental results show that the addition of these alloying elements increases the roughness and hardness specially due to formation of Fe-rich intermetallic ��-����5��������. However, the needle-like ��-����5�������� has been …

Effect Of Variation Of Sic Mass Fraction On Mechanical Properties Of Al-Sic Composite Using Stir Casting Method, Sumarji Sumarji, Naufal Fardio Albajili, Mahros Darsin, Rahma Rei Sakura, Andi Sanata

Journal of Mechanical Engineering Science and Technology (JMEST)

Al-SiC is a composite composed of AA6061 as a matrix and SiC as a reinforcement particle. The variation of mass added will affect the mechanical properties of the composite because Al-SiC is hardenable, which means that its mechanical properties can be improved by adding the reinforcement component. However, an excessive portion of SiC leads to a decrease in mechanical properties. The purpose of this study was to find the optimal composition of the addition of SiC into the aluminium matrix to gain maximum tensile strength and hardness. The mass fraction variation that would be used in this composite was the …

Effect Of Homogenization Pressure On Bacterial Cellulose Membrane Characteristic Made From Pineapple Peel Waste, Muhamad Muhajir, Heru Suryanto, Yanuar Rohmat Aji Pradana, Uun Yanuhar

Journal of Mechanical Engineering Science and Technology (JMEST)

Many studies were conducted to maintain the environment by reducing the waste, especially pineapple peel waste. This study aims to explore the effect of various pressure of the homogenization process on bacterial cellulose membrane surface morphology and structure produced using extract of pineapple peel waste. The methods include the preparation of pellicle samples from the product of the fermentation process of Acetobacter xylinum using a medium from the extract of pineapple peel waste. Bacterial cellulose pellicles were crushed using a blender. Mashed bacterial cellulose pellicle was homogenized in High-Pressure Homogenizer with pressure variation of 150 bar, 300 bar, 450 bar, …

Machine Vision For The Various Road Surface Type Classification Based On Texture Feature, Susi Marianingsih, Widodo Widodo, Marla Sheilamita S. Pieter, Evanita Veronica Manullang, Hendry Y. Nanlohy

Journal of Mechanical Engineering Science and Technology (JMEST)

The mechanized ability to specify the way surface type is a piece of key enlightenment for autonomous transportation machine navigation like wheelchairs and smart cars. In the present work, the extracted features from the object are getting based on structure and surface evidence using Gray Level Co-occurrence Matrix (GLCM). Furthermore, K-Nearest Neighbor (K-NN) Classifier was built to classify the road surface image into three classes, asphalt, gravel, and pavement. A comparison of KNN and Naïve Bayes (NB) was used in present study. We have constructed a road image dataset of 450 samples from real-world road images in the asphalt, gravel, …

Gasohol Engine Performance With Various Ignition Timing, Hendry Y. Nanlohy, Suyatno Suyatno, Helen Riupassa, Marthina Mini, Trismawati Trismawati, Mebin Panithasan

Journal of Mechanical Engineering Science and Technology (JMEST)

Experimental research has been conducted on the effect of ignition timings on the characteristics and performance of gasohol engines such as power, torque, specific fuel consumption, and thermal efficiency. The fuel used in this research is pure gasoline and a mixture of 50% bioethanol (BE50). The results show that the ignition timing that gives the maximum effect occurs at the top and bottom dead points of 9 degrees for gasoline and 12 degrees for BE50 fuel. Furthermore, the maximum power is obtained at 6,500 rpm, and at an ignition time of 12 degrees BTDC the maximum power generated is 4.63 …

Research Progress Of Copper Electrodeposition Filling Mechanism In Silicon Vias, Yun-Na Sun, Yong-Jin Wu, Dong-Dong Xie, Han Cai, Yan Wang, Gui-Fu Ding

Journal of Electrochemistry

Aiming at the electroplating filling problem of deep via TSV (through silicon via) interconnection, the multi-compatible integrated manufacturing technology team at the Shanghai Jiao Tong University has completed the numerical solution of the equations and realized the numerical simulation of TSV filling mode by applying the finite element method with arbitrary Lagrange Euler algorithm. The filling mechanisms of blind vias, the butterfly filling form for the through vias and the simultaneous filling mode of vias with different aspect ratios are analyzed by simulation, contributing to the parameter optimization and sample manufacturing. The effects of electroplating current density and heat treatment …

Effect Of Corrosion Inhibitors On Copper Etching To Form Thick Copper Line Of Pcb In Acidic Etching Solution, Xiao-Li Wang, Wei He, Xian-Ming Chen, Hong Zeng, Yuan-Zhang Su, Chong Wang, Gao-Sheng Li, Ben-Xia Huang, Lei Feng, Gao Huang, Yuan-Ming Chen

Journal of Electrochemistry

The chemical compounds of 2-mercaptobenzothiazole (2-MBT), benzotriazole (BTA) and phenoxyethanol (MSDS) as corrosion inhibitors were used to inhibit the copper etching to form the thick copper line of PCB in the acidic etching solution. The inhibition status was characterized with contact angle measurement, electrochemical test and etch factor calculation, while the corrosion morphology of copper surface was studied by scanning electron microscope. The adsorption mechanism of corrosion inhibitors on copper surface is analyzed by molecular dynamics and quantum chemistry calculations. The results indicated that the synergistic function of the two inhibitors could effectively promote their adsorption on the copper surface …

Mechanism And Application Of Nickel Nano-Cone By Electrodeposition On A Flexible Substrate, Xiu-Ren Ni, Ya-Ting Zhang, Chong Wang, Yan Hong, Yuan-Ming Chen, Yuan-Zhang Su, Wei He, Xian-Ming Chen, Ben-Xia Huang, Zhen-Lin Xu, Yi-Feng Li, Neng-Bin Li, Yong-Jie Du

Journal of Electrochemistry

Nano-array structure possesses promising prospect in power supply, optical device and electronic manufacturing. In this paper, a black nickel nano-cone array was prepared on a flexible substrate by galvanostatic deposition and the corresponding factors involved in the fabrication of nickel nano-cone array was explored. Experimental results showed that a large current density and low main salt concentration were not favored to the formation of cone nickel structure. It was also found that ammonium chloride, as the crystal modifier, was crucial to deposit the uniform nano-cone array. In addition, the growth mechanism of nickel nano-cone was further studied by molecular dynamics …

Electrodeposition Of Functional Epitaxial Films For Electronics, Kui Huang, Rong-Jiao Huang, Su-Qin Liu, Zhen He

Journal of Electrochemistry

Electrodeposition is a solution-based synthesis technique that can be used to fabricate various functional materials on conductive or semiconductive substrates under ambient conditions. Electrodeposition is usually triggered by an artificial electric stimulation (i.e., applied potential/current) to the substrate to oxidize or reduce ions, molecules, or complexes in the deposition solution layer near the substrate surface, which drives this solution layer to depart from its thermodynamic equilibrium and consequently causes the assembly of targeted deposits on the substrate. During electrodeposition, many experimental parameters could affect the properties of the deposits in different ways. To date, many elements (both metals and nonmetals), …