Engineering Commons^™

Design Of Nitroxide-Based Radical Polymer Materials For Electronic Applications, Martha E. Hay

Open Access Theses

Radical polymers represent a new class of organic electronic materials that rely on an oxidation-reduction (redox) reaction to transport charge. That is, stable radical sites pendant to the polymer backbone communicate electronically through a rapid oxidation-reduction reaction. This redox mechanism has previously been established as effective for charge-storage applications (e.g., secondary batteries). When applied in the solid state, radical polymers demonstrate electrical conductivity on par with that of first-generation conjugated polymer electronic materials. This initial success has prompted interest in developing design rules for radical polymers. Specifically, this thesis explores the impact of radical density in a polymer …

Degradation Of High Performance Polymeric Fibers: Effects Of Sonication, Humidity And Temperature On Poly (P-Phenylene Terephthalamide) Fibers, Nelyan Lopez-Perez

Open Access Theses

High performance fibers are characterized by properties such as high strength and resistance to chemicals and heat. Due to their outstanding properties, they are used on applications under harsh environments that can degrade and decrease their performance. Fiber degradation due to different chemical and mechanical factors, is a process that begins at a microstructural level. Changes in the polymer’s chemical or physical structure can alter their mechanical properties. Knowledge of the structure-properties relationship and the effects of environmental chemical and physical factors over time, is crucial for the improvement and development of high performance fibers.

In this study ballistic fibers …

Fundamental Studies Of Flame Propagation In Lean-Burn Natural Gas Engines, Zhiyan Wang

Open Access Dissertations

Lean-burn natural gas engines offer enhanced thermal efficiencies and reduced soot and NOx emissions. However, cycle-to-cycle variability in combustion that can result from unreliable ignition, variability in equivalence ratio and quenching is a challenge. Reliability of ignition can be improved by employing a dual-fuel ignition strategy in which a small quantity of diesel fuel is injected to initiate ignition. Computational studies of n-heptane/methane-air mixing layers are performed to provide insight into the fundamental physics of dual-fuel ignition. The results show that the characteristic time required for steady premixed flame propagation has three components: time for autoignition to occur, time for …

Hollow Fiber Membranes For Artificial Lung Applications, Lauren Reed

Chemical Engineering Undergraduate Honors Theses

Artificial lungs are in use, but difficult issues remain in the field of membrane development related to fouling issues. Currently there are external artificial lungs circulating blood outside the body, taking out the carbon dioxide, and inserting oxygenated blood back into the body. An example of this type of machine is the ExtraCorporeal Membrane Oxygenation (ECMO) machine currently used in hospitals. The ECMO takes over the functions for both the lungs and the heart but is only available for short term use by patients with respiratory failure due to infections [1]. The fibers in the machine develop fouling due to …

Membrane Chromatography For Bioseparations: Ligand Design And Optimization, Zizhao Liu

Graduate Theses and Dissertations

Membrane chromatography, or membrane adsorber, represents an attractive alternative to conventional packed bed chromatography used in downstream processing. Membrane chromatography has many advantages, including high productivity, low buffer consumption and ease to scale up. This doctoral dissertation focuses on developing novel polymeric ligands for protein separations using membrane chromatography. Atom transfer radical polymerization (ATRP), known as a controlled radical polymerization technique, has been used to control the architecture of grafted polymeric ligands. The center theme of this dissertation is to develop new polymeric ligands and investigate how the polymer’s property (e.g. flexibility, hydrophobicity) and architecture (e.g. chain density, chain length) …

Nanoemulsions Within Liposomes For Cytosolic Drug Delivery To Multidrug-Resistant Cancer Cells, Jacob Brian Williams

Theses and Dissertations

Cancer cells that survive chemotherapy treatment often develop resistance to the administered chemotherapeutics, as well as to many other types of drugs, because the cancer cells increase their production of efflux pumps in the cell. This undesired phenomenon of resistance to cancer drugs is known as multidrug resistance. This work uses a novel drug carrier, called an eLiposome, to achieve cytosolic drug delivery to kill multidrug-resistant cancer cells. An eLiposome consists of a perfluoropentane (PFC5) emulsion droplet inside of a liposome. Folate attached to the eLiposome facilitates uptake into the cell. The PFC5 droplet is metastable at body temperature, but …

Chlorpyrifos Removal For Wastewater Reuse, Indran Kamalanathan

Chemical Engineering Undergraduate Honors Theses

Approximately 1.2 billion people around the world live in areas of physical water scarcity. This could increase to half of the world’s population by 2030 and could displace 24 to 700 million people unless steps are taken to ensure adequate water supply.¹ Water scarcity is an escalating issue within the United States, specifically in Western inland states with arid climates. This scarcity is encouraging communities to investigate tertiary level municipal wastewater treatment, allowing for reuse of wastewater. Unfortunately, wastewater contains numerous contaminants that are not regulated by the Environmental Protection Agency (EPA) under the Safe Drinking Water Act (SDWA). …

Haul Truck Tires Recycling, Omkar Bhave

Chemical Engineering Undergraduate Honors Theses

The disposal of large Off-the-Road (OTR) tires is an increasingly important concern. These tires can weigh up to 8,450 pounds with an overall diameter and width of approximately 140.7 inches and 45.1 inches respectively. OTR tires are used for mining vehicles such as haul trucks, wheel loaders, backhoes, graders, and trenchers.[1] These new tires cost between $38,000 and $50,000 each, depending on multiple factors including oil prices and the cyclical nature of the industry. Haul trucks contain six tires per vehicle, and mines replace these tires around every 9-12 months.[2] Statistics regarding discarded OTR tires are not provided by the …

Plasmonic Pervaporation For Sustainable Mixture Separation, Ty Austin

Chemical Engineering Undergraduate Honors Theses

The U.S. Department of Energy suggests that ca. 40% of the total energy consumed in the chemical and refining industries is used for distillation.¹ One potentially energy efficient alternative is pervaporation, a membrane separation process that uses differences in solvent permeability and vaporization rates to encourage mixture separation. Pervaporation has become a valuable tool in the processes of producing biofuels, recovering water, and removing solvent.^2,3 However, implementation has been hindered by heating the feed to the membrane and cooling the unpermeated retentate to increase membrane throughput at a higher energy cost. Preliminary research has shown that locally heating …

Measurement Of Activity And Stability Of Physical Vapor Deposition (Pvd) Coated Crystal Surfaces, Anuradha Krishnan

Masters Theses

The overall objective of this research work is to investigate the hydrophilic and hydrophobic forces acting on organic crystal planes and understanding the interaction of functional groups with additive molecular nanolayers. Crystals of acetaminophen and lactose were made and the surface forces were tested on Atomic Force Microscope (AFM). Uniformity of crystal surface was confirmed from the AFM study in the first stage. The growth factors of crystal planes as a function of time were studied. Adhesion forces on plain crystals were measured on both two different organic crystals made of acetaminophen and lactose. In the second stage, …

Evaluation Of Smart Water Flooding In A Selected Uae Carbonate Oil Reservoir, Mohammad Jasem Khalifi

Chemical and Petroleum Engineering Theses

Water flooding is by far the most common method of improved oil recovery applied in oil reservoirs. Water is the cheapest source of external energy that has been used over decades in water flooding schemes, provided that the damage does not adversely affect its injectivity. Displacement efficiency of water flooding can be significantly affected by crude oil/water/rock interactions. Historically, some consideration was given to such interactions in the practice of reservoir engineering. In recent years, extensive research in this area has documented that higher oil recoveries can be obtained when low-salinity water is injected in a formation with high salinity …

Electrostatic Nanosmearing Architecture Of Additive Functional Groups During High Shear Mixing Of Pharmaceutical Blends, Sajan Kumar Chatarla

Masters Theses

The main objective of the research project is to detect and quantify the rate and extent of nanosmearing of hydrophobic functional groups of additives on multiple pharmaceutical particles during high shear mixing of formulations due to electrostatics affecting critical blend properties on the bulk scale. We accomplished this task by systematically detecting the electrostatics during powder flow and its consequence on the nanosmearing distribution of additives during mixing. In the first stage, the electrostatic behavior of particles was correlated to the powder flow. Secondly, its relative influence on nanosmearing of additives during mixing was determined by developing a methodology to …

How A Systematic Approach To Uncertainty Quantification Renders Molecular Simulation A Quantitative Tool In Predicting The Critical Constants For Large N-Alkanes, Richard Alma Messerly

Theses and Dissertations

Accurate thermophysical property data are crucial for designing efficient chemical processes. For this reason, the Design Institute for Physical Properties (DIPPR 801) provides evaluated experimental data and prediction of various thermophysical properties. The critical temperature (T_c), critical density (ρ_c), critical pressure (P_c), critical compressibility factor (Z_c), and normal boiling point (T_b) are important constants to check for thermodynamic consistency and to estimate other properties. The n-alkane family is of primary interest because it is generally assumed that other families of compounds behave similarly to …

Design, Construction, And Preliminary Testing Of A Square Cross-Sectional Mixing Chamber, Holly Holmes-Smith

Chemical Engineering Undergraduate Honors Theses

Throughout the US, large quantities of chlorine are produced and transported by rail. In the past, train accidents led to deadly accidental releases and the need for mass evacuation. However, moving people unnecessarily may cause pandemonium or danger to health for sensitive members of the public. In these past cases, the models used for evacuation distances did not accurately predict the impact of the chlorine release, but these models did not take into account the reactivity of chlorine. Because chlorine is a highly reactive gas, it is absorbed into the surrounding environment which reduced the amount of chlorine in the …

Effects Of Tethering Placement And Linker Variations On Antibody Stability On Surfaces, Rebecca Ellen Grawe

Theses and Dissertations

An antibody microarray consists of antibody bound to a surface. Antibody microarrays have great potential in many fields, particularly as a tool to detect antigens. Unfortunately, antibodies suffer from poor performance. A greater understanding of how antibodies interact with surfaces would improve microarray design and performance, but experimental methods fall short of being able to observe these interactions. Therefore molecular simulation has emerged as the primary method to study protein/surface interactions.The simulations here were coarse grain simulations performed using the model of Karanicolas and Brooks. Additionally, an advanced surface model was used that allows for different surface chemistries. PyMBAR analysis …

Removal Of Carboxylic Acids And Water From Pyrolysis Oil, George Alexander Marshall

Graduate Theses and Dissertations

Over 70% of the world’s energy consumption is provided by fossil fuels and with those reserves depleting at a fast rate, alternative energy sources or methods are needed to support the world’s energy needs. This research was done in an attempt to make it more economically feasible to produce fuel products, such as bio-diesel, from the upgrading of bio-oil obtained from the pyrolysis of biomass waste material such as sawdust. The high water and oxygenated compound content of bio-oil make it undesirable for fuel use; however, two methods involving surface modified commercial membranes were utilized in hopes of overcoming these …

Plasma Processes And Polymers Third Special Issue On Plasma And Cancer, Mounir Laroussi, Annemie Bogaerts, Nazir Barekzi

Electrical & Computer Engineering Faculty Publications

(First paragraph) This issue of Plasma Processes and Polymers is the third in a series on the applications of low temperature plasma (LTP) against cancer, or “plasma oncology.” The papers in this issue are inspired from the talks given at the third International Workshop on Plasma for Cancer Treatment (IWPCT) which took place on April 11–12, 2016 in Washington, DC, USA. IWPCT is an international workshop that was created in 2014 as a venue to share cutting edge plasma oncology research. The first IWPCT was held in Washington DC, under the co-chairmanship of Prof. Mounir Laroussi (Old Dominion University) and …

Design And Synthesis Of Dynamic Covalent Polymer Scaffolds With Controlled Architectures, Emily Annette Hoff

Dissertations

The design and synthesis of functional, controlled polymer architectures is essential to the development of new materials with precise and tailorable properties or applications. The work described in this dissertation focuses on the development of controlled polymer architectures with dynamic linkages for the design of multifunctional materials and surfaces via robust, efficient, and stimuli-responsive strategies.

In Chapter III, a post-polymerization modification strategy based on ambient temperature nucleophilic chemical deblocking of polymer scaffolds bearing N-heterocycle blocked isocyanate moieties is reported. Room temperature RAFT polymerization of three azole-N-carboxamide methacrylates, including 3,5-dimethyl pyrazole, imidazole, and 1,2,4-triazole derivatives, afforded reactive polymer scaffolds …

Nanostructured Morphologies In Glassy Polymer Networks, Brian Greenhoe

Dissertations

The body of this work describes a novel approach for the dispersion of multi-walled carbon nanotubes in a high T_g epoxy prepolymer matrix using a twin screw high-shear continuous reactor. The method demonstrated improves on previous dispersion methods in several ways. It offers increased efficiency through excellent heat transfer, while being solvent-less, scale-able, and tailorable to drive dispersion states to judiciously chosen dispersion states. Furthermore, it was shown that dispersion state and agglomerate morphology can be directed, in several ways, through processing conditions and also by controlling the matrix viscosity profile through cure. Broadband dielectric spectroscopy, optical hot-stage microscopy, …

Conformationally Superarmed S-Ethyl Glycosyl Donors As Effective Building Blocks For Chemoselective Oligosaccharide Synthesis In One Pot, Mithila Bandara, Jagodige Yasomanee, Nigam Rath, Christian Pedersen, Mikael Bols, Alexei Demchenko

Chemistry & Biochemistry Faculty Works

A new series of superarmed glycosyl donors has been investigated. It was demonstrated that the S-ethyl leaving group allows for high reactivity, which is much higher than that of equally equipped S-phenyl glycosyl donors that were previously investigated by our groups. The superarmed S-ethyl glycosyl donors equipped with a 2-O-benzoyl group gave complete β-stereoselectivity. Utility of the new glycosyl donors has been demonstrated in a one-pot one-addition oligosaccharide synthesis with all of the reaction components present from the beginning.

Determination Of Aqueous Surfactant Solution Surface Tensions With A Surface Tensiometer, Remelisa Esteves, Birce Dikici Ph.D, Matthew Lehman, Qayyum Mazumder, Nonso Onukwuba

Beyond: Undergraduate Research Journal

Surfactant solutions are applicable to engineering systems for cooling equipment for electronics. Surfactants can be added to water to improve heat transfer. An application of using aqueous surfactant solutions can be through microchannel heat sink. Although it is ideal to redesign these systems to reduce heat, it is a costly method. Surfactant solutions at optimal solution concentration can be able to transfer heat quickly and effectively with minimum expense. The surface tension of surfactant solutions is an important parameter for boiling heat transfer and must be taken into consideration. The purpose of this research is to measure surface tension of …

Determination Of Surfactant Solution Viscosities With A Rotational Viscometer, Remelisa Esteves, Nonso Onukwuba, Birce Dikici Ph.D

Beyond: Undergraduate Research Journal

Aqueous surfactant solutions are used in engineering systems for improving boiling heat transfer. The purpose of this research is to determine the viscosities of surfactant solutions and to investigate the effect of composition on viscosity. The results obtained can possibly be used as reference for further study in the effects of surfactant solution viscosities on nucleate boiling. A rotational viscometer was used to determine the viscosities of three surfactant solutions – SLS, EH-14, and SA-9 – of various compositions at room temperature. It was discovered that the viscosities of SLS, EH-14, and SA-9 had a nearly consistent pattern as their …

Development Of Metal Matrix Composite Gridlines For Space Photovoltaics, Omar K. Abudayyeh

Chemical and Biological Engineering ETDs

Space vehicles today are primarily powered by multi-junction photovoltaic cells due to their high efficiency and high radiation hardness in the space environment. While multi-junction solar cells provide high efficiency, microcracks develop in the crystalline semiconductor due to a variety of reasons, including: growth defects, film stress due to lattice constant mismatch, and external mechanical stresses introduced during shipping, installation, and operation. These microcracks have the tendency to propagate through the different layers of the semiconductor reaching the metal gridlines of the cell, resulting in electrically isolated areas from the busbar region, ultimately lowering the power output of the cell …

Photocatalytic Reduction Of Co2 With Tunable Bandgap And Bandedge Materials, Thuhuong T. Ngo

USF Tampa Graduate Theses and Dissertations

Solar energy is a sustainable resource which has substantial potential to meet the increasing demand for renewable energy. Though there has been some success in harvesting solar energy for electricity production, converting solar energy to chemical energy as fuels is still a challenge due to low efficiency.

Since the discovery of TiO₂ photocatalysts for splitting water (4) and reducing CO₂ (5) to form useful chemical feedstock such as H₂, CO and CH₄, much research has been done to increase the efficiency of photocatalysts. However, the current conversion efficiency of photocatalysts remains low (~5%) (6, …

Fabrication Of High Performing Pemfc Catalyst-Coated Membranes With A Low Cost Air-Assisted Cylindrical Liquid Jets Spraying System, Xiong Peng, Travis Omasta, William Rigdon, William E. Mustain

Faculty Publications

In this work, a low cost air-assisted cylindrical liquid jets spraying (ACLJS) system was developed to prepare high-performance catalyst-coated membranes (CCMs) for proton exchange membrane fuel cells (PEMFCs). The catalyst ink was flowed from a cylindrical orifice and was atomized by an air stream fed from a coaxial slit and sprayed directly onto the membrane, which was suctioned to a heated aluminum vacuum plate. The CCM pore architecture including size, distribution and volume can be controlled using various flow parameters, and the impact of spraying conditions on electrode structure and PEMFC performance was investigated. CCMs fabricated in the fiber-type break-up …

Electrochemical Fabrication Of Energetic Thin Films, Jonathan J. Coleman

Chemical and Biological Engineering ETDs

Current thermal battery heat sources suffer from slow reaction propagation rates and require extreme care when handling to protect from inadvertent ignition sources. Nanostructured intermetallic heat sources are strong candidates for improved heat sources as they have high enthalpy of reaction, are highly conductive before and after firing and are completely gasless reactions. Current fabrication methods of these heat sources rely on a PVD multistep layering process that is time and capital intensive, and cost prohibiting to their use. The composition and nanostructuring these films require can be provided with electrochemical codeposition, where the two components (aluminum and nickel) are …

Dielectric Characterization Of Mylar And The Effects Of Doping Processes, Cami B. Belcher

Chemical and Biological Engineering ETDs

Mylar® polymer is a bi-axially oriented polyethylene terephthalate (PET) polymer film used widely as a dielectric, specifically in capacitors. The dielectric characteristics of Mylar have been well studied and documented over the years; however, many of the mechanisms responsible for dielectric breakdown and failure are not understood for modified versions of the material. Previous studies on Mylar confirm that factors such as temperature, humidity, and voltage ramp rates can also have a significant effect on the dielectric properties and measurement of the dielectric properties. This study seeks to determine how dielectric properties, including permittivity, dielectric loss, and breakdown strength, are …

Peridynamic Modeling Of Ruptures In Biomembranes, Michael Taylor, Irep Gözen, Samir Patel, Aldo Jesorka, Katia Bertoldi

Mechanical Engineering

We simulate the formation of spontaneous ruptures in supported phospholipid double bilayer membranes, using peridynamic modeling. Experiments performed on spreading double bilayers typically show two distinct kinds of ruptures, floral and fractal, which form spontaneously in the distal (upper) bilayer at late stages of double bilayer formation on high energy substrates. It is, however, currently unresolved which factors govern the occurrence of either rupture type. Variations in the distance between the two bilayers, and the occurrence of interconnections (“pinning sites”) are suspected of contributing to the process. Our new simulations indicate that the pinned regions which form, presumably due to …

Evaluation Of Ultrasound Assisted Potassium Permanganate Pre-Treatment Of Spent Coffee Waste, Rajeev Ravindran, Swarna Jaiswal, Nissreen Abu-Ghannam, Amit Jaiswal

Articles

In the present study, novel pre-treatment for spent coffee waste (SCW) has been proposed which utilises the superior oxidising capacity of alkaline KMnO₄ assisted by ultra-sonication. The pre-treatment was conducted for different exposure times (10, 20, 30 and 40 min) using different concentrations of KMnO₄ (1,2, 3, 4, 5% w/v) at room temperature with solid/liquid ratio of 1:10. Pretreating SCW with 4% KMnO₄ and exposing it to ultrasound for 20 min resulted in 98% cellulose recovery and a maximum lignin removal of 46%. 1.7fold increase in reducing sugar yield was obtained after enzymatic hydrolysis of KMnO_{4 …}

Inhibition Of Microbial Biofuel Production In Drought-Stressed Switchgrass Hydrolysate, Rebecca Garlock Ong, Alan Higbee, Scott Bottoms, Quinn Dickinson, Dan Xie, Scott A. Smith, Jose Serate, Edward Pohlman, Arthur Daniel Jones, Joshua J. Coon, Trey S. Kato, Gregg R. Sanford, Dustin Eilert, Dustin G. Oates, Jeff S. Piotrowski, Donn M. Bates, David Cavalier, Yaoping Zhang

Department of Chemical Engineering Publications

Background:

Interannual variability in precipitation, particularly drought, can affect lignocellulosic crop biomass yields and composition, and is expected to increase biofuel yield variability. However, the effect of precipitation on downstream fermentation processes has never been directly characterized. In order to investigate the impact of inter-annual climate variability on biofuel production, corn stover and switchgrass were collected during 3 years with significantly different precipitation profiles, representing a major drought year (2012) and 2 years with average precipitation for the entire season (2010 and 2013). All feedstocks were AFEX (ammonia fiber expansion)-pretreated, enzymatically hydrolyzed, and the hydrolysates separately fermented using xylose-utilizing strains …