Engineering Commons^™

Extractive Membranes For The Detection And Screening Of Waterborne Plutonium, James Foster

All Dissertations

The development of rapid screening tools for special nuclear materials remains a crucial focus for nonproliferation efforts. Traditional approaches for the analysis of trace-level Pu isotopes in water requires tedious and time-consuming sample preparation steps that do not lend well to expeditious screening. Therefore, a novel analytical method that combines both Pu concentration and source preparation into a single detection system would make for an invaluable tool for nuclear security applications. Extractive membranes absorbers can help to fulfill this role as they are capable of concentrating Pu to detectable limits while subsequently serving as alpha spectrometry sample sources. In Chapter …

Optimizing Virus Prefiltration For Biopharmaceutical Manufacturing, Solomon Isu

Graduate Theses and Dissertations

Virus filters are single-use devices that use a size-based separation process. In virus filters, contaminating virus particles are retained while the therapeutic molecules pass through the membrane pores. Virus filters are an essential component of the overall virus clearance strategy. Sections 1 and 2 of this dissertation provide an introduction and extensive review of monoclonal antibody (mAb) process development, where virus filtration is pivotal. In section 3, prefiltration studies were performed with an industrially relevant IgG1 type mAb using adsorptive and size-exclusion-based prefilters with different mechanisms of action. This mAb has an isoelectric point range of 7.1 to 8.0 and …

Mechanical Behavior Of Clay Soil Stabilized With Fly Ash And Bottom Ash, Soewignjo Agus Nugroho, Azra Zulnasari, Ferry Fatnanta, Andius Dasa Putra

Makara Journal of Technology

Soil is one of the most important aspects of an infrastructure given its functions of receiving and holding structural loads. However, not all soils have good physical and mechanical properties. To overcome those conditions, stabilization of the soil is practiced to meet the technical requirements. This study aims to determine the behavior of high plasticity clay stabilized with lime, fly ash, and bottom ash. These additives can be used as a stabilizing agent to increase soil strength. The percentage of additives varied from 5%–25% then mixed with clay and were tested through the (Unconfined Compression Strength (UCS) test. The UCS …

Enhancement Of Biogas Production Through Solid-State Anaerobic Co-Digestion Of Food Waste And Corn Cobs, Lukhi Mulia Shitophyta, Anisa Salsabila, Firanita Angraini Putri, Siti Jamilatun

Makara Journal of Technology

Although biogas has been primarily produced through liquid anaerobic digestion, this method leads to the floating and stratification of fibers and non-homogeneous mixing, which can reduce the biogas yield. Alternatively, biogas can be produced by the solid-state anaerobic digestion (SS-AD) of organic material with a high solid content, such as corn cobs. We investigated the co-digestion of food waste and corn cobs as a biomass feedstock for SS-AD in biogas production. We measured the effects of the total solid (TS) content, percentage of food waste, and reduction in volatile solids (VS), from which we determined its appropriate kinetic model. We …

Control Strategy For Solar Energy-Saving Lamps For Optimized Energy Utilization And Sustainability Of Operation Durability: Indonesia Case, Burhanuddin Halimi, Agus Purwadi, Nana Heryana

Makara Journal of Technology

To solve the electrification ratio issue, the Indonesian government has promoted the use of solar energy-saving lamps. This study proposes a control strategy that adopts current reference time-based profiling for solar energy-saving lamps. For optimal energy consumption, the current reference profile is determined according to users’ daily energy requirements. From the aspect of user comfort, a gradual step reference profile is also introduced to provide a subtle change in lighting intensity level. The proposed control strategy can minimize energy consumption and optimize the operation durability of the system. The concept is verified by simulating four scenarios, the results of which …

Adjusting The Alloying Degree Of Pt3Zn To Improve Acid Oxygen Reduction Activity And Stability, Tian-En Zhang, Ya-Ni Yan, Jun-Ming Zhang, Xi-Ming Qu, Yan-Rong Li, Yan-Xia Jiang

Journal of Electrochemistry

Proton exchange membrane fuel cell (PEMFC) is a new type of energy device, a relatively excellent way to achieve carbon neutrality. However, due to the relatively slow reaction rate of oxygen reduction reaction (ORR) at the cathode, platinum (Pt) is the key material of the cathode catalyst. However, Pt is a kind of noble metal, and its high cost restricts the PEMFC commercialization process. At present, the main approach is to combine transition metals with Pt to prepare Pt-based alloys and to reduce the use of Pt. Pt-based alloys are excellent catalysts for ORR, improving both the activity and stability, …

Preparation Of Pt@Basrtio3 Nanostructure And Its Properties Towards Photoelectrochemical Ammonia Synthesis, Jing Zhang, Rui-Xia Guo, Jian-Jun Fu, Shi-Bin Yin, Pei-Kang Shen, Xin-Yi Zhang

Journal of Electrochemistry

Ammonia is an important industrial raw material and a potential green energy. Using renewable energy to convert nitrogen into ammonia under ambient condition is an attractive method. However, the development of efficient photoelectrochemical ammonia synthesis catalysts remains a challenge. Perovskite such as BaSrTiO₃ (BST) is a good photocatalytic material. However, BST is active under ultraviolet light and has a high recombination rate of photogenerated electron-hole pairs. By dispersing precious metals, it can effectively regulate the absorption of sunlight by BST. In this work, we used a two-step method to prepare BST. The H₂PtCl₆·6H₂O …

Tuning The Physicochemical, Structural, And Antimicrobial Attributes Of Whey-Based Poly (L-Lactic Acid) (Plla) Films By Chitosan Nanoparticles, Farhad Garavand, Milad Rouhi, Shima Jafarzadeh, Diako Khodaei, Ilaria Cacciotti, Masoumeh Zargar, Seyed Hadi Razavi

Research outputs 2022 to 2026

Recently, the research and innovation to produce raw materials from microbial processes has gained much attention due to their economic and environmental impacts. Lactic acid is a very important microbial product due to its wide application in the food, pharmaceutical, cosmetic, and chemical industries. In the current study, poly (L-lactic acid) (PLLA) was produced by the ring opening polymerization (ROP) technique of L-lactic acid recovered from whey fermentation, and was used for the production of nanocomposites films reinforced with chitosan nanoparticles (CNPs) (average diameter ca. 100–200 nm). Three different CNPs concentrations, namely 1, 3, and 5% w/w, were tested, and …

Acoustofluidics For Simultaneous Nanoparticle-Based Drug Loading And Exosome Encapsulation, Zeyu Wang, Joseph Rich, Nanjing Hao, Yuyang Gu, Chuyi Chen, Shujie Yang, Peiran Zhang, Tony Jun Huang

Faculty Publications

Nanocarrier and exosome encapsulation has been found to significantly increase the efficacy of targeted drug delivery while also minimizing unwanted side effects. However, the development of exosome-encapsulated drug nanocarriers is limited by low drug loading efficiencies and/or complex, time-consuming drug loading processes. Herein, we have developed an acoustofluidic device that simultaneously performs both drug loading and exosome encapsulation. By synergistically leveraging the acoustic radiation force, acoustic microstreaming, and shear stresses in a rotating droplet, the concentration, and fusion of exosomes, drugs, and porous silica nanoparticles is achieved. The final product consists of drug-loaded silica nanocarriers that are encased within an …

Contact Angles Of A Brine On A Bituminous Coal In Compressed Hydrogen, Rossen Sedev, Hamed Akhondzadeh, Mujahid Ali, Alireza Keshavarz, Stefan Iglauer

Research outputs 2022 to 2026

Hydrogen storage is a main issue in the establishment of a hydrogen economy. Geo-storage could be a viable solution if hydrogen could be injected into and withdrawn from suitable geological formations, reversibly and reliably. Rock wettability is a major factor as it affects injectivities, withdrawal rates, storage capacities, and containment security. We report here the contact angles of a brine on the surface of a bituminous coal in a pressurized hydrogen atmosphere. Under realistic geo-storage conditions the coal surface was weakly water-wet. Hydrogen pressure increased brine contact angles at 25°C but did not have an impact at 50 or 70°C. …

The Aiche Student Design Competition: Modular Distributed Gas-To-Liquids (Gtl) Synthesis, Abigail Bozarth, Jason Mote, Revathi Panuganti, Fausat Isu

Honors Capstone Projects and Theses

No abstract provided.

Koh Vs Deionized Water Operation In Anion Exchange Membrane Electrolyzers, Noor Ul Hassan, Yiwei Zheng, Paul A. Kohl, Mustain E. William

Faculty Publications

Anion exchange membrane water electrolyzers (AEMELs) have recently received significant attention due to their potential advantages over proton exchange membrane electrolyzers (PEMELs). However, some AEMELs feed an aqueous salt solution to the cell where PEMELs typically feed deionized (DI) water. DI water is preferred to keep the system and maintenance costs low. Because of this, many AEMEL researchers report performance both in the salt solution (typically KOH) and DI water. However, the methodology for switching between KOH and DI water is often poorly defined, and it is unclear what impact the residual salt has on cell performance after switching from …

Effective Parameters Controlling Sterol Transfer: A Time‑Resolved Small‑Angle Neutron Scattering Study, Ursula Perez-Salas, Lionel Porcar, Sumit Garg, Manuela A.A. Ayee-Leong, Irena Levitan

Faculty Work Comprehensive List

Though cholesterol is the most prevalent and essential sterol in mammalian cellular membranes, its precursors, post-synthesis cholesterol products, as well as its oxidized derivatives play many other important physiological roles. Using a non-invasive in situ technique, time-resolved small angle neutron scattering, we report on the rate of membrane desorption and corresponding activation energy for this process for a series of sterol precursors and post-synthesis cholesterol products that vary from cholesterol by the number and position of double bonds in B ring of cholesterol’s steroid core. In addition, we report on sterols that have oxidation modifications in ring A and ring …

Bio-Ionic Liquid Functionalized Hydrogels Towards Smart Tissue Regeneration, Vaishali Krishnadoss

Theses and Dissertations

A blend of scaffolds, biologically active molecules, and cells are required to assemble functional constructs to repair and regenerate damaged tissue or organ via tissue engineering. The scaffold supports cell growth and proliferation and acts as a medium for diverse cellular activities. Even though hydrogel's high-water content and flexible nature make it a pronounced applicant as a scaffold, they exhibit significant technical limitations such as the absence of cell-binding motifs, lack of oxygen, conductivity, adhesive properties, growth of cells in a 3-dimensional (3D) microenvironment. In this thesis, a novel material platform is evaluated and studied to address the concerns mentioned …

Antiviral Polymers: A Review, Ali Akbari, Ashkan Bigham, Vahid Rahimkhoei, Sina Sharifi, Esmaiel Jabbari

Faculty Publications

Polymers, due to their high molecular weight, tunable architecture, functionality, and buffering effect for endosomal escape, possess unique properties as a carrier or prophylactic agent in preventing pandemic outbreak of new viruses. Polymers are used as a carrier to reduce the minimum required dose, bioavailability, and therapeutic effectiveness of antiviral agents. Polymers are also used as multifunctional nanomaterials to, directly or indirectly, inhibit viral infections. Multifunctional polymers can interact directly with envelope glycoproteins on the viral surface to block fusion and entry of the virus in the host cell. Polymers can indirectly mobilize the immune system by activating macrophages and …

Editorial For Gels 6th Anniversary Special Issue, Esmaiel Jabbari, Gulden Camci-Unal

Faculty Publications

Note: In lieu of an abstract, this is an excerpt from the first page.

This Special Issue celebrates many outstanding quality papers published in Gels over the past six years since its first issue was published in 2015 [...]

Investigation On The Effect Of Binders On The Performance Of Si-Based Anodes Of Lithium-Ion Batteries, Christopher Rohen

Honors Theses

For the production of lithium-ion batteries with the different binders, a few things must be considered. The process of production has several steps. First is the preparation of the slurry with the composition of 70/10/20, 70% active material, 10% carbon black and 20% selected binder. Then, the bar coating of the slurry into a copper sheet is required. After drying in the oven, the sample in the cooper sheet, a few holes on the sample are made and the half-cell assembly. Lastly, the cell is assembled and its subject of rigorous testing to determine performance and stability; A few of …

Comparison Of Bio-Mass To Bio-Oil Reactor Systems: Direct Conversion Vs. Companion Coal Gasification, Luci Evans

Honors Theses

The purpose of this project was to define, design, and optimize the economic feasibility of the production of bio-oil from a direct conversion of biomass to bio-oil using fast pyrolysis and a secondary side reaction of the production of a syngas from coal gasification. In the end, a combined process of these two was created to show the new strengths and more efficient options to produce a desired product within a budget. The main objectives of this project were to research the economic feasibility of the biomass and bio-oil industry, obtain a market survey, design two process flow diagrams showing …

Assembly Of Nanostructures At Solid-Liquid And Liquid-Air Interfaces, Yingzhen Ma

LSU Doctoral Dissertations

Molecular and nanoscale colloids such as surfactant, fatty acid and metallic nanoparticles are widely used in numerous applications such as detergents, biomedicine, and catalyst. The assemblies of these colloids show different morphological behavior in aqueous solution due to the wide range of intermolecular interactions such as hydrogen bonding, van der Waals, and electrostatics. The morphology of these assemblies can be changed by environmental factors including temperature, ionic strength, and salinity. However, the guidance to direct assembled state of colloidal assemblies at heterogenous interfaces under various external stimuli remains poorly understand. In this Ph.D. dissertation, we show the adsorption and reconfiguration …

Novel Thermal Coating For High-Speed Airplanes, Abinash Satapathy, Lakshay Battu, Liam Watson, Nazanin Rajabi

Symposium of Student Scholars

In comparison to various other materials, Carbon Fiber, specifically Carbon Fiber Reinforced Polymers (CFRP), is pre-eminent amongst other materials for use on aeronautical systems. Due to its high specific strength (strength-to-weight ratio), CFRP is prominent for carrying heavy loads while maintaining a lightweight build. However, when influenced by heat resulting from air resistance, CFRP is known to undergo serious degradation that would significantly decrease the effectiveness of the polymers. To prevent this degradation and maintain the strength of the CFRP, thermal protective layers (TPLs) are designed to shield the CFRP from heat exposure. This research is focused on the examination …

Determination Of The Heating Time Constant For Root Crops, Z K. Ergasheva, Beraat Ozcelik

Technical science and innovation

Convective drying refers to one of the energy-intensive processes used in chemical, woodworking, food and other industries. Therefore, in modern conditions, when there is a growing shortage and an increase in energy tariffs, it is important to develop and apply new effective methods of drying wet materials in industrial production, create high-performance drying equipment, improve the operation of existing dryers, which will contribute to the rational use of natural resources, reduce the cost of finished products and increase the competitiveness of production. Root crops are plants in which nutrients are concentrated in tubers or roots. Jerusalem artichoke refers to sugar-containing …

The Effect Of Chitosan On The Surface Properties Of Cellulose-Based Paper Obtained From The Stem Of Flaxseed, E A. Egamberdiev, Y T. Ergashev, Kh Kh Khaydullaev, G Y. Akmalova, G R. Rakhmonberdiev

Technical science and innovation

This paper examines the effects of chitosan, starch, and polyvinyl alcohol (PVA) to improve the surface properties of cellulose-based paper obtained from local raw materials. The polymers are incorporated into the paper polythene by spraying. The results showed that the addition of chitosan to paper polythene, which is made of cellulose fibers, has an improvement in surface properties compared to the effect of other additives. The degree of exposure of starch coincided with the degree of exposure of chitosan, but it resulted in a decrease in the water absorption potential of the paper compared to chitosan at the same concentration. …

Limits Of Detection Of Mycotoxins By Laminar Flow Strips: A Review, Xinyi Zhao, Hugh Byrne, Christine M. O’Connor, James Curtin, Furong Tian

Articles

Mycotoxins are secondary metabolic products of fungi. They are poisonous, carcinogenic, and mutagenic in nature and pose a serious health threat to both humans and animals, causing severe illnesses and even death. Rapid, simple and low-cost methods of detection of mycotoxins are of immense importance and in great demand in the food and beverage industry, as well as in agriculture and environmental monitoring, and, for this purpose, lateral flow immunochromatographic strips (ICSTs) have been widely used in food safety and environmental monitoring. The literature to date describing the development of ICSTs for the detection of different types of mycotoxins using …

Feasibility Study Of Implementing Gamma-Ray Computed Tomography On Measuring Aggregate Distribution And Radiation Shielding Properties Of Concrete Samples, Omar Farid, Nima Farzadnia, Kamal Khayat, Muthanna H. Al-Dahhan

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Aggregate segregation is one of the key defects that impair the performance of concrete at fresh and hardened stages. This study aims to assess the feasibility of using an advanced technique to identify/scan/determine the aggregate segregation of concrete elements and determine radiation shielding properties of the concrete. The gamma-ray computed tomography (γ-CT) technique was employed to study aggregate distribution/dispersion in self-consolidating concrete (SCC). Accordingly, two SCC mixtures with moderate segregation (MS) and high segregation (HS) levels were cast and compared with highly stable SCC with no segregation (NS). The γ-CT scans were located on three different levels of concrete specimens …

Simplified Thermal Runaway Model For Assisting The Design Of A Novel Safe Li-Ion Battery Pack, Paul T. Coman, Eric C. Darcy, Ralph E. White

Faculty Publications

This paper presents a simplified thermal runaway model (FEM) used to guide the design of a novel battery pack designed to resist thermal runaway propagation passively. The model is based on the heat equation for a 2D geometry with a heat generation term based on the maximum amount of energy measured using a custom-made calorimeter. The model was validated against experimental data using a 48-cell subscale of a full-scale battery pack for three different runs with three trigger cells with Internal Short Circuit Devices (ISCD) implanted in the separators. One trigger cell was placed at the edge, one placed in …

Assessment Of Wettability And Rock-Fluid Interfacial Tension Of Caprock: Implications For Hydrogen And Carbon Dioxide Geo-Storage, Muhammad Ali, Bin Pan, Nurudeen Yekeen, Sarmad Al-Anssari, Amer Al-Anazi, Alireza Keshavarz, Stefan Iglauer, Hussein Hoteit

Research outputs 2022 to 2026

Underground hydrogen (H2) storage (UHS) and carbon dioxide (CO2) geo-storage (CGS) are prominent methods of meeting global energy needs and enabling a low-carbon global economy. The pore-scale distribution, reservoir-scale storage capacity, and containment security of H2 and CO2 are significantly influenced by interfacial properties, including the equilibrium contact angle (θE) and solid-liquid and solid-gas interfacial tensions (γSL and γSG). However, due to the technical constraints of experimentally determining these parameters, they are often calculated based on advancing and receding contact angle values. There is a scarcity of θE, γSL, and γSG data, particularly related to the hydrogen structural sealing potential …

Chitosan/Polyacrylamide Green Gels For Water Control In High-Temperature Reservoirs, Mohamed Shamlooh, Reem Elaf, Ibnelwaleed A. Hussein, Mohammed Saad, Baojun Bai

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

The rheology of a gel system composed of polyacrylamide (PAM) and chitosan is studied under typical reservoir conditions. The impacts of the degree of chitosan deacetylation, temperature, and salinity on the gelation behavior are assessed. The said system was prepared under ambient conditions and matured for 24 h at altered temperatures ranging from 50 up to 125 °C. An optimum formulation has been identified considering the rheological response and the initial viscosity constraints. The increase in the degree of syneresis with the degree of deacetylation indicates the long-Term thermal stability of the gels. Ammonium chloride was an effective retarder for …

Reactive Oxygen Species (Ros)-Responsive Size-Reducible Nanoassemblies For Deeper Atherosclerotic Plaque Penetration And Enhanced Macrophage-Targeted Drug Delivery, Jianhua He, Wenli Zhang, Xiaoju Zhou, Fengfei Xu, Jiahui Zou, Qiqi Zhang, Yi Zhao, Hongliang He, Hu Yang, Jianping Liu

Chemical and Biochemical Engineering Faculty Research & Creative Works

Nanoparticle-based therapeutics represent potential strategies for treating atherosclerosis; however, the complex plaque microenvironment poses a barrier for nanoparticles to target the dysfunctional cells. Here, we report reactive oxygen species (ROS)-responsive and size-reducible nanoassemblies, formed by multivalent host-guest interactions between β-cyclodextrins (β-CD)-anchored discoidal recombinant high-density lipoprotein (NP³_ST) and hyaluronic acid-ferrocene (HA-Fc) conjugates. The HA-Fc/NP³_ST nanoassemblies have extended blood circulation time, specifically accumulate in atherosclerotic plaque mediated by the HA receptors CD44 highly expressed in injured endothelium, rapidly disassemble in response to excess ROS in the intimal and release smaller NP³_ST, allowing for further …

Studying Dispersed Phase Holdup In A Pilot Plant Agitated Liquid–Liquid Mixer By Developing Online Expanded Laser Beam Based Technique, Kifah H. Abid, Jihane Mendil, Muthanna H. Al-Dahhan

Chemical and Biochemical Engineering Faculty Research & Creative Works

Expanded Laser Transmission Technique (E-LTT), where a laser beam is used in conjunction with a beam expander large enough to cover the average drop size up to a few millimeters in the path of the laser in a liquid–liquid dispersion mixture, has been applied for online continuous measurement and investigation in a non-invasive manner of the drop phase volume fraction in an agitated flow mixer of a pilot plant scale. The limitations of beam scattering by the drops through the dispersion path were overcome by having liquids of matching refractive indices enabled by the temperature control system. This study reports …

Development & Validation Of A Piv System For Obtaining Data From A Uasb Reactor, Camila D' Bastiani, Gerald Gallagher, David Kennedy, Anthony Reynolds

Conference Papers

Anaerobic digestion processes can generate energy in the form of biogas while treating organic wastewater. The efficiency of the treatment, and thus the generation of biogas, is closely linked to the type and design of the reactor, and the technology used. Granular anaerobic digestion technology offers advantages such as a higher loading rate and reduction of the space needed. However, the hydrodynamics inside this type of reactor can be complex due to the presence of solids (granules) and gas (biogas) phases along with the liquid phase (wastewater). This is one of the reasons why the study and optimization of reactors …