Engineering Commons^™

Oceanic Shear Measurements Using The Airfoil Probe, Thomas Osborn, Thomas Siddon

Symposia on Turbulence in Liquids

Vertical profiles of salinity and temperature in the ocean reveal fluctuations with length scales as small as a few mil 1imeters. These fluctuations, called microstructure by oceanographers, are the small scale results of turbulent mixing processes. It is hoped that through the study of microstructure we can evaluate the relative importance of different sources of the turbulent energy (e.g., tides, large scale internal waves, etc.) and the mechanisms for generation of the turbulence (e.g., wave overturn, shear instability, etc.).

There is a considerable body of evidence to suggest that shear instability is an important mechanism in the generation of ocean …

Flow Visualization Studies On Drag-Reducing Turbulent Flows, R. H. J. Sellin

Symposia on Turbulence in Liquids

Flow visualisation studies in a square duct of internal dimensions 44.5 x 44.5 mm are reported. The flow marker is a stream of opaque white dye, released from a downstream facing stationary tube, and it is photographed through the plexiglass wall of the duct. The point of dye release can be traversed in a direction perpendicular to the duct wall and three locations are investigated, two in the core of the flow and one in the near- wall region. By using Is exposure times photographs are obtained of a dye dispersion cone and the cone angle is measured and related …

Measurement Of Reynolds Stress And Turbulence In Dilute Polymer Solution By Laser Velocimeter, Samuel E. Logan

Symposia on Turbulence in Liquids

Measurements of Reynolds stress and axial and transverse turbulence intensities have been made in turbulent pipe flow of a dilute solution of high molecular weight polymer and compared to measurements made with pure water. A laser velocimeter capable of measuring these turbulence parameters has been developed and utilized.

Axial turbulence intensities are consistent in behavior and magnitude with previous polymer results and the measurements of transverse intensity and Reynolds stress are similarly well behaved and self consistent. Sublayer thickening in drag reducing polymer solution is observed, in consonance with earlier work. New results include demonstration that the turbulent shearing stress …

Ldv Measurements In Turbulent Free Convection, R. J. Adrian

Symposia on Turbulence in Liquids

The design and performance of a laser Doppler velocimeter (LDV) used in a turbulent water-overice convection experiment are described. The LDV was operated in a reference beam mode with an ultrasonic diffraction grating shifting the reference beam frequency to provide bipolar sensing of the vertical velocity, and a phase-locked loop was used to demodulate the Doppler frequency information. The maximum observed velocities in the experiment were ± 1 mm/sec, and the accuracy of instantaneous measurement was limited by Brownian motion and laser line width to ± .04 mm/sec for a 2 Hz frequency response. The practical difficulties encountered in this …

Measurements In Turbulent Water And Two-Phase Flows By Laser Anemometry, A. Melling, J. H. Whitelaw

Symposia on Turbulence in Liquids

Measurements of the mean and rms values of the longitudinal velocity in a rectangular duct are reported. These results were obtained in a water flow using a laser anemometer. The important design criteria which facilitated the measurements are described and gradient, transit-time, noise and refractive-index corrections are specifically discussed. The results demonstrate the development of a rectangular duct flow and, in particular, reveal that a small lack of symmetry at the duct entrance can readily be identified in the normal- stress results, 37 hydraulic diameters downstream.

The possibility of utilizing water droplets in steam and gas bubbles in water to …

Individual Realization Laser-Doppler Technique Applied To Turbulent Channel Flow, W. G. Tiederman, D. K. Mclaughlin, M. M. Reischman

Symposia on Turbulence in Liquids

Measurements of the mean and turbulence intensity of the streamwise velocity component in a fully developed, two-dimensional channel flow of water are presented. The measurements were made with the individual realization laser Doppler technique and emphasize the near-wall region of the flow. A dual-scatter optical arrangement was used which employs 90° scattering and yields a probe volume whose length normal to the wall is 0.0075 inches. A correction has been made to the data that accounts for the statistical biasing which occurs in the individual realization technique. The corrected data demonstrate that the individual realization technique can yield accurate velocity …

Analysis Of A Laser Correlation Anemometer, L. Lading

Symposia on Turbulence in Liquids

An analysis of a laser anemometer is given. The anemometer is based on the cross correlation of the random signals generated by the scattering from -- and/or extinction of -- two parallel laser beams. The basic set-up is compared with the laser Doppler anemometer.

It is shown that the correlation function exhibits a broadening and generally also a skewness - equivalent to the broadening (transit time) and skewness (velocity gradients) of the Doppler spectrum.

The conditions for "instantaneous point" measurements are derived.

It is shown how a particle (drop/bubble) size versus particle velocity spectrum can be obtained by appropriate electronic …

Optimization Of An Lda System, Robert Smid

Symposia on Turbulence in Liquids

This paper discusses the various considerations leading to the optimization of a laser Doppler anemometer for measurements in the flows of gases, liquids, and solids. The requirements placed on the various parameters of the optics by the experiment are discussed in general for different modes of operation. Expressions determining these optical parameters in certain instances given by various authorities are presented and compared. This includes such topics as: laser power, particle size, measuring volume size, optical variation in transmitting and receiving optics, and photodetector selection.

Features Of A Separating Turbulent Boundary Layer As Revealed By Laser And Hot-Film Anemometry, R. L. Simpson, J. H. Strickland, P. W. Barr

Symposia on Turbulence in Liquids

Experiments have been performed to determine the fundamental nature of boundary layer separation produced by an adverse pressure gradient. Measurements upstream and downstream of the separation zone have been made utilizing laser and hot-film anemometry techniques.

A completely mobile backscattering laser anemometer was developed. This alone is a significant development because of the relatively long focal lengths required for measurements in a 36" wide wind tunnel. Signal processing was achieved by a digital signal sampling and storage system. Both mean and fluctuating velocities in both the unseparated and separated flow regions were measured. Experimental results are in fairly good agreement …

Design Considerations For A Laser Doppler Velocimeter, Leroy M. Fingerson

Symposia on Turbulence in Liquids

In optimizing an instrument design, it is important to differentiate between the theoretical limitations of the technique and apparent limitations that can be reduced or eliminated by design. In the laser-Doppler anemometer, the theoretical limits are associated with the fact that particle velocity is the measurement rather than fluid velocity. The accuracy and speed of the particle velocity measurements do not appear to have theoretical limitations. Therefore, instrument design must concentrate on improving the measurement of particle velocity.

A complete system has been designed to optimize accuracy, speed, convenience, and flexibility in measuring particle velocity. The problems inherent in transferring …

Turbulence Measurements With A Sampling Laser-Doppler Velocimeter, P. D. Iten

Symposia on Turbulence in Liquids

A novel sampling signal processor overcomes the difficulties encountered with frequency trackers in the investigation of unseeded highly turbulent flows. This sampling system consists essentially of a swept filter, e.g. a standard RF-spectrum analyzer, a digital data memory and a storage oscilloscope. It is able to determine first-order statistical averages of turbulent flows with high fluctuation frequencies and amplitudes even at very low scattering particle concentrations. Since the velocity samples are not statistically independent of the velocity, the sampled velocity data has to be corrected in order to obtain unbiased statistical averages. A theoretical analysis and experimental investigations of the …

Phase Separation In Turbulent Two-Phase Flow, Francois J. Resch, Hans J. Leutheusser

Symposia on Turbulence in Liquids

The paper is based on an experimental study of a typical instance of bubbly two-phase flow, viz. the air-entraining roller zone of hydraulic jumps in open channels. The investigation was undertaken with the aid of hot-film anemometry techniques involving instant digitization of analog signals, and delayed electronic processing of the tape-recorded data. Special computer programs were designed to separate the two phases according to a well-defined signal threshold. It is this aspect of the work which is being dealt with in the paper.

Turbulent Characteristics Of Two-Phase, Gas-Liquid Stratified Channel Flow, D. M. Johns, T. G. Theofanous, R. N. Houze

Symposia on Turbulence in Liquids

The turbulence characteristics of the bulk phases were studied in a stratified, two-dimensional, gas- liquid channel flow. Initial results are presented comparing mean velocity and turbulent intensity profiles with those obtained in a prior study at the same bulk phase Reynolds numbers. The results indicate that comparison of two realizations of stratified gas- liquid flow cannot be adequately done on the basis of bulk-phase Reynolds numbers. Comparisons must be based on some more fundamental relationships involving the gas-liquid interactions.

Conditioned Sampling Techniques, R. E. Kaplan

Symposia on Turbulence in Liquids

The concept of organized, spatially coherent large scale structures has been investigated for a variety of turbulent shear flows by a technique called "Conditional Sampling." It can be shown that these structures are related to physically important activities such as, 1) the entrainment of turbulent boundary layers, and 2) the maintenance of turbulence by a wall, 3) the growth of free shear layers, and 4) the structure and noise production of turbulent jets.

The general technique of conditioned sampling is related to visualizations of the flow, and to problems of synchronization of images in the presence of noise. While there …

Experiments On The Structure Of Turbulence In Fully Developed Pipe Flow, T. R. Heidrick, S. Banerjee, R. S. Azad

Symposia on Turbulence in Liquids

This paper describes a series of two-point measurements in fully developed pipe flow. Measurements of the phase shifts between the Fourier components of the axial velocity fluctuations at two points were made with three different orientations of the two points. In all cases the two points were close enough together that the turbulent structure remained essentially "frozen" while passing between the sensors. The phase velocities, C₁(f), and inclinations, α(f) (defined previously by Heidrick et al. (8)), of each frequency component, f, were determined from these measurements.

In general, the Fourier components are inclined to the wall - the …

Experimental Measurement Of Particle Dispersion In Turbulent Flow, N. M. Howard, C. C. Meek, B. G. Jones

Symposia on Turbulence in Liquids

The dispersion of particles in turbulent flows, phenomena such as dispersion, diffusion, and sedimentation, and a more fundamental point of view, the description of particle interaction with the turbulent field are recently of increasing interest. A system capable of investigating statistical structure of the motion of particles in a turbulent fluid flow using a turbulent water pipe flow system and particles tagged with C0-60 radioactive pellets has been constructed and tested. The particles were followed in their trajectory by a group of detectors consisting of NaI(Tℓ) crystals mounted on photomultiplier tubes which move with the particles on a movable carriage. …

A Comparison And Analysis Of Detection Methods For The Measurement Of Production In A Boundary Layer, G. R. Offen, S. J. Kline

Symposia on Turbulence in Liquids

Two hot films and dye visualizations have been employed, simultaneously, in a turbulent boundary layer to explore the relations among visual observations and five kinds of detection methods using conditional sampling. The results show that all methods correlate positively with each other, but not with high enough values of correlation coefficients to indicate true correspondence between any two thus far studied. Moreover, none of the detection methods devised to date indicate a plateau in number of events as a function of trigger threshold.

The results also provide additional information on several other matters: (i) the relationship of outward motions from …

An Experimental And Theoretical Study Of The Viscous Sublayer For Turbulent Tube Flow, Lindon C. Thomas, H. L. Greene

Symposia on Turbulence in Liquids

Flush-mounted anemometer probes have been used to further study characteristics of the viscous sublayer for both Newtonian and drag reducing solutions, with particular emphasis given to low Reynolds number turbulent tube flow. Experimental measurements for the mean frequency of bursting or renewal within the wall region are compared with theoretical predictions obtained on the basis of the surface renewal and penetration model.

Both theory and experiment taken together suggest that the effect of the mean axial pressure gradient on the viscous sublayer becomes important for the deeper molecular penetration associated with low Reynolds number flow. Also, a pronounced lessening of …

On The Interpretation Of The Output Of Hot-Film Anemometers And A Scheme Of Dynamic Compensation For Water Temperature Variation, J. Tan-Atichat, H. M. Nagib, J. W. Pluister

Symposia on Turbulence in Liquids

Using a special calibration tunnel developed during the course of this study, the static and dynamic response of several kinds of commercially available hot-film probes with single and multiple sensors of the cylindrical-fiber type are examined. The effects of different parameters, including those of the anemometer bridge, on the output and performance of the probes are evaluated. In particular, the consequences of variations in water temperature on the hot-film anemometer output are determined. The results reveal a large effect of the water temperature on the calibration curves (in an extreme case a change in temperature of only 5.5°F can result …

Use Of The Split-Film Sensor To Measure Turbulence In Water Near A Wall, Paul H. Blinco, V. A. Sandborn

Symposia on Turbulence in Liquids

Because of its small size and unique design, the 0.15-mm diameter split-film sensor has many significant advantages over the conventional X-configuration hot-film sensor and the yaw-wire technique for measuring turbulence near a wall. Calibration of the split- film sensor indicates that the magnitude and yaw angle of the instantaneous velocity vector is dependent only on the sum and ratio of the sensor outputs, respectively. Results of limited measurements of the longitudinal and vertical turbulence intensities and Reynolds stress for hydraulically smooth, free surface flows are presented. Digital time series of the split-film outputs revealed the following information: (1) the split-film …

Author Index, University Of Missouri--Rolla

Symposia on Turbulence in Liquids

No abstract provided.

Measurements Of Pulsating Turbulent Water Flow In A Tube, S.-Z. Lu, R. J. Nunge, F. F. Erian, M. Mohajery

Symposia on Turbulence in Liquids

The experimental method associated with obtaining meaningful information from the hot-film anemometer signals in fully developed pulsating turbulent flow where the pulsations are sinusoidal in time is discussed. The results of a number of experiments in water reveal the nature of the longtime and short-time average velocity and pressure. Velocity measurements between 0.95 radii and the centerline demonstrate that the long-time average velocity distribution is coincident with that for steady turbulent flow at the same Reynolds number. Also, no significant differences between the longtime average axial pressure drop in the pulsating and steady flows were noted, although this requires further …

Intermittency And Structure Of A Jet Exhausting Into A Stratified Fluid, Alan Brandt, H. E. Gilreath, C. L. Yates, C. R. Walton

Symposia on Turbulence in Liquids

This preliminary study of the mechanism by which local turbulent regions generate internal gravity waves in a stably stratified fluid is based on comparisons of the visual and hot-film- anemometer observations of a jet exhausting into a stratified fluid with those for a jet exhausting into a homogeneous medium. The stratified environment limits the growth of the mean jet boundary, or from another point of view, inhibits the vertical motion of the instantaneous turbulent/non-turbulent interface. The visual and non-conditional statistical averages agree with expectations and with previous measurements in stratified turbulent wakes. Application of a standard criterion to determine the …

Promising Directions For Liquid Turbulence Research --Panel Discussion, Victor Goldschmidt, J. H. Whitelaw, V. A. Sandborn, Val Kibens, R. E. Kaplan

Symposia on Turbulence in Liquids

No abstract provided.

Conference Proceedings Of The 3rd Biennial Symposium On Turbulence In Liquids, University Of Missouri--Rolla

Symposia on Turbulence in Liquids

The Third Biennial Symposium on Turbulence in Liquids showed further progress in the investigator's ability to measure turbulence parameters and in the general understanding of turbulence. The most impressive advances in measurement seemed to be the ability to measure deeper into the turbulent boundary layer in order to obtain profiles over the entire turbulence production region and the rapid development of conditioned-sampling techniques for studying hypotheses for mechanisms.

Dynamic Response Of Forced Convective Heat Transfer From Cylinders To Low Prandtl Number Fluids, D. G. Malcolm, V. Verma

Symposia on Turbulence in Liquids

The present paper can be viewed as an extension of the work of Lim and Sleicher (9). They evaluated the frequency response of the heated element submerged in liquid metal by a perturbation method for Peclet numbers of up to 0.4. Velocity fluctuations were assumed small and second-order perturbations neglected. The Oseen approximation was made to the velocity field. Here the velocity configuration has been approximated to that of potential flow and the convection equation has been solved numerically with the aid of a digital computer. The potential flow approximation, as compared with the Oseen approximation, is reasonable over a …

Polymers From The Hydrolysis Of Tetraethoxysilane, B. W. Peace, Kenneth G. Mayhan, J. F. Montle

Chemical and Biochemical Engineering Faculty Research & Creative Works

The hydrolysis of tetraethoxysilane was studied under various solvent and temperature conditions. A method was developed by which reaction rates can be measured even in the presence of alcohols other than ethanol. The structures of the resulting polymers were dependent upon the reaction conditions employed, those formed at high temperature being highly condensed materials. © 1973.

Electrochemical Reduction Of Molybdenum(Vi) Compounds In Molten Lithium Chloride-Potassium Chloride Eutectic, Branko N. Popov, H. A. Laitinen

Faculty Publications

Molybdenum (VI) oxide reacts with molten LiCl-KCl eutectic at 450° to form MoO₂CI₂, which probably is present as an anion MoO₂Cl₄⁼, and pyromolybdate, Mo₂O₇⁼. Both of these species are electrochemically reduced to MoO₂, which can be reoxidized to MoO₂Cl₂ by current reversal. A second reduction step, observed whether MoO₃ or Mo₂O₇²⁻ is added to the melt, can be attributed to the reduction of MoO₄⁻⁻, formed as a secondary reaction product in the first …

Commentary On And Extension Of Calculative Procedure For Co2 Production, Ralph M. Rotty

Mechanical & Aerospace Engineering Faculty Publications

Further refinements are made in the method of calculating amounts of carbon dioxide released to the atmosphere through the combustion of fossil fuels. Data available in the UN Statistical Yearbook are used as the basic sources rather than the summary, World Energy Supplies, U.N. Statistical Papers, Series J because the most recent data are available several months earlier in the yearbook and because data are included for natural gasoline, natural gas liquids, and cement production. Coal, lignite, crude petroleum, “marketed” natural gas, flared natural gas, and cement are itemized separately and revised CO₂ emission estimates are made for …

Mass Transfer Coefficients Determined By Simplex Optimization Techniques, Charles Ferris Callihan

Masters Theses

"The objective of this thesis is to develop a method for obtaining individual mass transfer coefficients in absorption columns. There are two assumptions which apply throughout the thesis. The first assumption is "plug flow." The second assumption is that the axial concentrations can be measured accurately enough.

The problem is approached by simulating data generated from a mathematical model of an absorption column. A response surface is defined which is a function of the individual mass transfer coefficients. The lowest point on the surface locates the individual mass transfer coefficients for the system in question.

The mathematical model of the …