Engineering Commons^™

Integrated Model-Centric Decision Support System For Process Industries, Daira Aragon

LSU Doctoral Dissertations

To bring the advances in modeling, simulation and optimization environments (MSOEs), open-software architectures, and information technology closer to process industries, novel mechanisms and advanced software tools must be devised to simplify the definition of complex model-based problems. Synergistic interactions between complementary model-based software tools must be refined to unlock the potential of model-centric technologies in industries. This dissertation presents the conceptual definition of a single and consistent framework for integrated process decision support (IMCPSS) to facilitate the realistic formulation of related model-based engineering problems. Through the integration of data management, simulation, parameter estimation, data reconciliation, and optimization methods, this framework …

Flame Interactions And Burning Characteristics Of Two Live Leaf Samples, Brent M. Pickett, Carl Isackson, Rebecca Wunder, Thomas H. Fletcher, Bret W. Butler, David R. Weise

Faculty Publications

Combustion experiments were performed over a flat-flame burner that provided the heat source for multiple leaf samples. Interactions of the combustion behavior between two leaf samples were studied. Two leaves were placed in the path of the flat-flame burner, with the top leaf 2.5 cm above the bottom leaf. Local gas and particle temperatures, as well as local oxygen concentrations, were measured along with burning characteristics of both leaves. Results showed that the time to ignition of the upper leaf was not significantly affected by the presence of the lower leaf. The major difference observed was that the time of …

Classification Of Fine Particles Using A Taylor-Couette Device, Navina Durgaiah Tungapindi

Masters Theses

"The study of fine particle classification is common, especially since a well defined particle size distribution is important in most processes and products. Many methods have been developed to classify micron-size particles, and although each has its own advantage, most cannot classify particles to an extremely narrow range. This is partly due to the cohesive nature of fine particles, which can be due to electrostatic attraction, moisture, or van der Waals forces. In order to overcome this problem, a wet method of classification has been chosen here. Taylor vortices, discovered in 1923, develop in the fluid contained in the annulus …

Development And Evaluation Of An Effective Process For The Recovery Of Oil And Detoxification Of Meal From Jatropha Curcas, Sarthak Gaur

Masters Theses

"There has been significant research on biofuels to ensure national security and economic stability of the US. Jatropha curcas, a hardy plant, holds tremendous potential as a biodiesel source and cattle feed-stock largely due to its high triglyceride and crude protein content. However, its viable economic utilization is limited due to the presence of important toxic compounds, phorbol esters. A novel and efficient process has been developed that obtains high yields of jatropha oil and detoxifies the defatted (oil free) jatropha meal. Principles of solid-liquid extraction were utilized to detoxify the meal and then liquid chromatography was employed to analyze …

2008-2009 Che Newsletter, Department Of Chemical Engineering, Michigan Technological University

Department of Chemical Engineering Newsletters

Table of Contents

• Department
• Faculty
• Research
• Alumni & Friends
• 2008 Industrial Advisory Board
• Convocation
• Student News

Utilizing Mixed Surfactants For Simultaneous Pore Templating And Active Site Formation In Metal Oxides, Mohammed Shahidur Rahman

University of Kentucky Doctoral Dissertations

Self-assembled nonionic alkyl glycoside surfactants are of interest for creating functional adsorption and catalytic sites at the surface of mesoporous metal oxides, but they typically impart poor long-range order when used as pore templates. Improved order and control over the functional site density may be achieved by mixing them with a cationic surfactant. To confirm this hypothesis, we investigate the lyotropic liquid crystalline (LLC) phase behavior of aqueous solutions of the functional nonionic surfactant n-dodecyl β-D-maltoside (C₁₂G₂) and cationic cetyltrimethylammonium bromide (C₁₆TAB). A ternary phase diagram of the C₁₆TAB-C₁₂G_{2 …}

An Infrared Imaging Method For High-Throughput Combinatorial Investigation Of Hydrogenation-Dehydrogenation And New Phase Formation Of Thin Films, H. Oguchi, Jason R. Hattrick-Simpers, I. Takeuchi, E. J. Heilweil, L. A. Bendersky

Faculty Publications

We have developed an infrared imaging setup enabling in situ infrared images to be acquired, and expanded on capabilities of an infrared imaging as a high-throughput screening technique, determination of a critical thickness of a Pd capping layer which significantly blocks infrared emission from below, enhancement of sensitivity to hydrogenation and dehydrogenation by normalizing raw infrared intensity of a Mg thin film to an inert reference, rapid and systematic screening of hydrogenation and dehydrogenation properties of a Mg–Ni composition spread covered by a thickness gradient Pd capping layer, and detection of formation of a Mg₂Si phase in a …

Inhomogeneous Degradation Of Polymer Electrolyte Membrane In Pem Fuel Cells, Xinyu Huang, Wonseok Yoon

Faculty Publications

Membrane durability is one of the technical barriers for the commercialization of polymer electrolyte membrane (PEM) fuel cells. Membrane embrittlement (a form of mechanical weakening) can lead to the frequently observed “sudden death” behavior of PEM fuel cells. It is the objective of this study to explore the fundamental mechanisms of the mechanical weakening of perfluorosulfonic acid (PFSA) based electrolyte membranes during the accelerated degradation test.

Sulfur Dioxide Crossover During The Production Of Hydrogen And Sulfuric Acid In A Pem Electrolyzer, John A. Staser, John W. Weidner

Faculty Publications

A proton exchange membrane (PEM) electrolyzer has been investigated as a viable system for the electrolysis step in the thermochemical conversion of sulfur dioxide to sulfuric acid for the large-scale production of hydrogen. Unfortunately, during operation, sulfur dioxide can diffuse from the anode to the cathode. This has several negative effects, including reduction to sulfur that could potentially damage the electrode, consumption of current that would otherwise be used for the production of hydrogen, introduction of oxygen and SO₂ to the hydrogen stream, and loss of sulfur to the cycle. However, proper water management can reduce or eliminate the …

The Effect Of Copt Crystallinity And Grain Texturing On Properties Of Exchange-Coupled Fe/Copt Systems, H. Oguchi, A. Zambano, M. Yu, Jason R. Hattrick-Simpers, D. Banerjee, Y. Liu, Z. L. Wang, J. P. Liu, S. E. Lofland, D. Josell, I. Takeuchi

Faculty Publications

The effect of the crystallinity and the grain texturing of CoPt hard layers on exchange coupled Fe/CoPt soft/hard magnetic systems was studied using gradient thickness multilayer thin films. We have studied the hard layer structures by transmission electron microscopy and x-ray diffraction, and characterized the exchange coupling interaction through magnetization loops obtained by the magneto-optical Kerr effect measurement. We found that exchange coupling strongly depends on the crystalline characteristics of the CoPt hard layer. There is correlation between the mixture of different grain orientations of the CoPt hard layer and coupling efficiency. In particular, interlayer coupling is enhanced when there …

Carbon Dioxide Capture From Flue Gases, Mohamed Rashid Al Rashid

Theses

Global warming and climate change are believed to be caused by the greenhouse effect. CO₂ has been regarded as the main contributor to global climate change which directly results in serious environmental problems. Half of the anthropogenic CO₂ emission sources are emitted from the combustion of fossil fuels in industries and power plants worldwide. The absorption behavior of Carbon dioxide from flue gases can be studied using conventional absorber and polymeric hollow fiber membrane contractors. An industrial absorber data was compared with simulated data using hollow fiber membrane contractor using the gPROMs software package. In this analysis, with …

Estimation Of The Flammability Zone Boundaries With Thermodynamic And Empirical Equations, Travis Joseph Hansen

Dissertations, Master's Theses and Master's Reports - Open

The flammability zone boundaries are very important properties to prevent explosions in the process industries. Within the boundaries, a flame or explosion can occur so it is important to understand these boundaries to prevent fires and explosions. Very little work has been reported in the literature to model the flammability zone boundaries. Two boundaries are defined and studied: the upper flammability zone boundary and the lower flammability zone boundary. Three methods are presented to predict the upper and lower flammability zone boundaries:

The linear model

The extended linear model, and

An empirical model

The linear model is a thermodynamic model …

Protein Responsive Synthetic Materials For Biomedical Applications, Youyou Zheng

Doctoral Dissertations

"The production of synthetic materials with molecular recognition abilities towards biomacromolecules has been widely researched because of its potential applications in separations, sensing, therapeutics, etc. While molecular imprinting has become a commercially viable method for the production of synthetic materials with molecular recognition abilities towards small molecules, little success has been recorded towards protein targets. Proteins are difficult to imprint as they present a number of epitopes for imprinting, are difficult to remove from the completed material, and are incompatible with the densely crosslinked structures required. As a result, a novel surface molecular imprinting technique was developed to synthesize polymeric …

Modelling And Simulation Of A Biomass Gasification-Solid Oxide Fuel Cell Combined Heat And Power Plant Using Aspen Plus, Wayne Doherty, Anthony Reynolds, David Kennedy

Conference Papers

In this paper the operation and performance of a high temperature solid oxide fuel cell (SOFC) stack on biomass syn-gas from a demonstration biomass gasification combined heat and power (CHP) plant is investigated. The objective of this work is to develop a computer simulation model of a biomass-SOFC CHP system, flexible enough for use in industry, capable of predicting system performance under various operating conditions and using diverse fuels. The biomass gasifier is of the dual fluidised bed (DFB) type with steam as the gasifying agent and is operated at atmospheric pressure. The tubular SOFC configuration, developed by Siemens Power …

Simulation Study Of Emerging Well Control Methods For Influxes Caused By Bottomhole Pressure Fluctuations During Managed Pressure Drilling, Hakan Guner

LSU Master's Theses

Managed Pressure Drilling (MPD) is an emerging drilling technology that utilizes mud weight, surface backpressure and annular frictional pressure loss (AFP) to precisely control the wellbore pressure. The goal of this project is to identify the most appropriate initial response and kick circulation method for the kicks that result from complications specific to MPD. These complications that can cause a reduction in bottomhole pressure were classified as surface equipment failures and unintended equivalent circulating density (ECD) reductions. Rotating control device (RCD) and pump failures are the examples of surface equipment failures. Pump efficiency loss and BHA position change represent the …

Prediction Of Light Gas Composition In Coal Devolatilization, Ravichandra S. Jupudi, Vladimir Zamansky, Thomas H. Fletcher

Faculty Publications

The chemical percolation devolatilization (CPD) model describes the devolatilization behavior of rapidly heated coal based on the chemical structure of the coal. It predicts the overall char, tar, and light gas yields. This paper presents an improved CPD model with improved capability for predicting light gas composition. This is achieved by incorporating a kinetic model that simulates the release of various light gas species from their respective sources/functional groups in coal. The improved CPD model is validated using experiments with a wire mesh reactor and published experimental observations

The Effect Of Rotation And Temperature On The Inhibition Performance Of Cashew (Anacardium Occidentale L.) Nut Shell Liquid On Co2 Corrosion Of Carbon Steel, J Mutasingwa

Tanzania Journal of Engineering and Technology (TJET)

A natural extract of cashew nut shells, Cashew Nut Shell Liquid (CNSL) was investigated as a corrosion inhibitor for carbon steel in 3% NaCl solutions saturated with CO2 gas using electrochemical techniques (i.e. potentiodynamic polarization and ac-impedance). The investigation was performed at different temperatures under static and dynamic conditions using a Rotating Disk Electrode (RDE). It was found that CNSL reduces the electrochemical processes taking place on carbon steel undergoing corrosion. The percentage inhibitor efficiency increases with increase in CNSL concentration and decreases with rise in temperature. Better performance at low CNSL concentration was registered under dynamic conditions and room …

Investigation Of The Effect Of Particle Size On Groundnut-Oil Solvent Extraction, S Manyele

Tanzania Journal of Engineering and Technology (TJET)

An investigation of the effect of particle size on the performance of vegetable oil recovery by solvent extraction is reported. Experiments were conducted using soxhlet extractor, groundnuts and n-hexane. Samples were grouped into mean particle sizes of 0.25, 0.75, 1.3, 3.3, and 7.5 mm using standard sieves. The effect of particle size was studied for extraction time intervals of 1, 2, 3, 4, 5 and 8 hours. The oil yield, oil recovered per kg solvent used, kg solvent lost per unit time, and the rate of extraction (kg oil recovered per hour) decreased with increasing particle size. Meanwhile, the percent …

The Multivariate Statistical Analysis Of Abiotic Parameters Of The Lake Tanganyika Sub Catchment, Hudson Nkotagu

Tanzania Journal of Engineering and Technology (TJET)

Results from multivariate statistical analysis of abiotic parameters conducted during the dry season at 20 accessible sites on 8 rivers, 2 lakes and a dam covering the Lake Tanganyika sub catchment are discussed. Standard methods were used to determine the levels of abiotic parameters from water samples. Physical parameters including DO, EC, Eh, turbidity, temperature, pH and secchi transparency were measured in situ while chlorophyll a was determined in the laboratory. Nutrients such as NO3-, SiO2, PO4 3- and Fe2+ were determined along with HCO3-. Factor analysis resulted in four factors including increased primary productivity, redox conditions, dissolution, and reduction …

Photopolymerization-Induced Crystallization And Phase Separation In Poly(Ethylene Oxide)/Triacrylate Blends, Soo Jeoung Park, Thein Kyu

College of Polymer Science and Polymer Engineering

The present article describes experimental and theoretical investigations of miscibility and crystallization behavior of blends of poly(ethylene oxide) (PEO) and triacrylate monomer (TA) using differential scanning calorimetry and optical microscopy. The PEO/TA blends manifested a single T(g) varying systematically with composition suggestive of a miscible character in their amorphous states. Moreover, there occurs melting point depression of PEO crystals with increasing TA. A phase diagram was subsequently established that exhibited a solid+liquid coexistence region bound by the liquidus and solidus lines, followed by an upper critical solution temperature (UCST) at a lower temperature. The emerging phase morphology was investigated to …

Fingering Instabilities On Reaction Fronts In The Co Oxidation Reaction On Pt(100), D. Bilbao, Jochen A. Lauterbach

Faculty Publications

Fingering instabilities arising from local perturbations to planar reaction fronts in the CO oxidation reaction on Pt(100) are presented. CO oxidation represents a heterogeneous nonlinear system with the necessary kinetic and diffusive transport properties to support the development of fingered wave fronts. External forcing was utilized to create CO wave fronts on an otherwise monostable, O-covered surface, which, upon destabilization, gave rise to fingers of adsorbed CO extending into the O adlayer ahead of the reaction front. Finger spreading and tip-splitting were observed as the finger pattern evolved towards an intrinsic wavelength, independent of the length of the reaction front, …

Multidimensional Modeling Of Solid Propellant Burning Rates And Aluminum Agglomeration And One-Dimensional Modeling Of Rdx/Gap And Ap/Htpb, Matthew Wilder Tanner

Theses and Dissertations

This document details original numerical studies performed by the author pertaining to solid propellant combustion. Detailed kinetic mechanisms have been utilized to model the combustion of the pseudo-propellants RDX/GAP and AP/HTPB. A particle packing model and a diffusion flame model have been utilized to develop a burning rate and an aluminum agglomeration model. The numerical model for RDX/GAP combustion utilizes a "universal" gas-phase kinetic mechanism previously applied to combustion models of several monopropellants and pseudo-propellants. The kinetic mechanism consists of 83 species and 530 reactions. Numerical results using this mechanism provide excellent agreement with RDX and GAP burning rate data, …

Organizational Agility, James D. Sterling

Business and Information Technology Faculty Research & Creative Works

No abstract provided.

Electrodeposition Of Nickel Nanowires And Nanotubes Using Various Templates, Asli Ertan, Surendra N. Tewari, Orhan Talu

Chemical & Biomedical Engineering Faculty Publications

Nickel nanotubes and nanowires are grown by galvanostatic electrodeposition in the pores of 1000, 100, and 15 nm polycarbonate as well as in anodised alumina membranes at a current density of 10 mA cm-2. The effects of pore size, porosity, electrodeposition time, effective current density, and pore aspect ratio are investigated. Nickel nanotube structures are obtained with 1000 nm pore size polycarbonate membrane without any prior treatment method. At the early stages of electrodeposition hollow nickel nanotubes are produced and nanotubes turn into nanowires at longer depositon times. As effective current density accounting for the membrane porosity decreases, the axial …

Antibacterial Coatings For Medical Devices Based On Glass Polyalkenoate Cement Chemistry, A. Coughlan, D. Boyd, C. W.I. Douglas, Mark R. Towler

Chemical and Biochemical Engineering Faculty Research & Creative Works

A biofilm is an accumulation of micro-organisms and their extracellular products forming a structured community on a surface. Biofilm formation on medical devices has severe health consequences as bacteria growing in this lifestyle are tolerant to both host defense mechanisms and antibiotic therapies. However, silver and zinc ions inhibit the attachment and proliferation of immature biofilms. The objective of this study is to evaluate whether it is possible to produce silver and zinc-containing glass polyalkenoate cement (GPC) coatings for medical devices that have antibacterial activity and which may therefore inhibit biofilm formation on a material surface. Two silver and zinc-containing …

Simulation Of Nanostructured Electrodes For Polymer Electrolyte Membrane Fuel Cells, Sanjeev M. Rao, Yangchuan Xing

Chemical and Biochemical Engineering Faculty Research & Creative Works

Aligned carbon nanotubes (CNTs) with Pt uniformly deposited on them are being considered in fabricating the catalyst layer of polymer electrolyte membrane (PEM) fuel cell electrodes. When coated with a proton conducting polymer (e.g., Nafion) on the Pt/CNTs, each Pt/CNT acts as a nanoelectrode and a collection of such nanoelectrodes constitutes the proposed nanostructured electrodes. Computer modeling was performed for the cathode side, in which both multicomponent and Knudsen diffusion were taken into account. the effect of the nanoelectrode lengths was also studied with catalyst layer thicknesses of 2, 4, 6, and 10 μm. It was observed that shorter lengths …

From Elastic Deformation To Terminal Flow Of A Monodisperse Entangled Melt In Uniaxial Extension, Yangyang Wang, Shi-Qing Wang

College of Polymer Science and Polymer Engineering

Using a well-entangled monodisperse styrene-butadiene random-copolymer (SBR) melt as a model system, we illustrate generic features of uniaxial extension behavior that may be shared by all well-entangled thermoplastic and elastomeric materials. Depending on the imposed extensional rate, the same sample may behave like a viscous liquid or an elastic "solid." Analogous to the recently revealed shear inhomogeneity, the SBR melt inevitably undergoes cohesive failure in the form of sample breakage whenever the Weissenberg number is much greater than unity, making it challenging to reach steady state. In the elastic deformation regime where the external deformation rate is faster than Rouse …

Flexography Printing Of Silver Based Conductive Inks On Packaging Substrates, Ramesh Chandra Kattumenu

Dissertations

Printing technologies for the production of flexible electronics have gained much interest due to its potential as a means to reduce the complexity and costs of present technology. High volume printing techniques like flexography are of great importance in order to produce rolls of flexible electronics printed directly on paper substrates. The proposed research will be focused on RFID components being in-line printed using flexography printing as the manufacturing platform. The properties of substrates and inks and printing process parameters are evaluated to study their effect on printed traces and RFID antenna. It was found in the study that properties …

A Fundamental Study Of The Pcr Amplification Of Gc-Rich Dna Templates, T. G. Mamedov, Elsje Pienaar, Scott E. Whitney, Joel R. Termaat, G. Carvill, R. Goliath, Anuradha Subramanian, Hendrik J. Viljoen

Hendrik J. Viljoen Publications

A theoretical analysis is presented with experimental confirmation to conclusively demonstrate the critical role that annealing plays in efficient PCR amplification of GC-rich templates. The analysis is focused on the annealing of primers at alternative binding sites (competitive annealing) and the main result is a quantitative expression of the efficiency (η) of annealing as a function of temperature (T_A), annealing period (t_A), and template composition. The optimal efficiency lies in a narrow region of T_A and t_A for GC-rich templates and a much broader region for normal GC templates. To confirm the …

Gene Expression Analysis Of Immobilized Saccharomyces Cerevisiae, Ryan Michael Summers

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Immobilization is an effective method to increase ethanol production, as proven by previous research. Results almost exclusively demonstrate an increase in ethanol production by and decrease in reproduction rate of immobilized Saccharomyces cerevisiae cells. Recently, research has been conducted to determine the cause of this change. The extreme variance in results due to lack of technology makes it difficult to determine the cellular changes induced by immobilization. With the advent of new technology, specifically gene expression analysis, the RNA content of cells can be easily and rapidly analyzed.

S. cerevisiae cells were immobilized in 3% (w/v) calcium alginate beads and …