Construction Engineering Commons^™

Automated Generation Of Daily Evacuation Paths In 4d Bim, Kyungki Kim, Yong-Cheol Lee

Durham School of Architectural Engineering and Construction: Faculty Publications

Spatial movements of workers and equipment should be carefully planned according to project plans. In particular, it is crucial for workers’ safety to prepare emergency evacuation paths according to changing construction site configurations and construction progress. However, creating evacuation paths for all crews for each day can be an extremely labor-intensive task if it is done manually. Consequently, in most construction projects, evacuation plans are not provided to managers and crews throughout the entire construction. Even state-of-the-art technologies do not suggest ways to generate evacuation paths according to changing progresses presented in 4-Dimensional Building Information Model (4D BIM). This research …

The Professional Constructor, Full Issue, Volume 44, Number 01

The Professional Constructor

No abstract provided.

Latex Modified Concrete - Very Early Strength, Bobby Steele

Purdue Road School

INDOT came out with specifications for a very early strength concrete to use on bridge deck overlays. This concrete is fast setting, which allows overlays to be performed over a weekend and benefits the traveling public with a short duration of traffic interference. Cure time to reach the strength requirement is 3 hours. E&B Paving performed the first application with the new spec on August 26, 2018. Many changes were also made to the INDOT Specification Section 722.

Final Design Review: Mascoma River Greenway Extension, Sebastian Strong, Sarah Atac, Eleanor Dowd, David Ruiz, Isalys Quiñones

ENGS 89/90 Reports

This report outlines current conditions surrounding the extension of the Mascoma River Greenway (MRG) to downtown West Lebanon, NH and recommends a route to completion. Included in the report are maps detailing potential route alignments and recommendations based on outside research and interviews with numerous stakeholders, Lebanon City officials, and community members. The report is intended to provide context and updated insight into the present and future of the MRG, following in the spirit of the 2010 MRG Action Plan, a document that created a vision for redevelopment of the Northern rail corridor and motivated stakeholders to move the project …

Building Homes And Hopes In Bangalore, India, Sherry S. Saroufeem

Construction Management

Habitat for Humanity Global Village is an organization that continuously sends volunteers to work on construction projects around the world. My team and I were chosen to go to a village in Bangalore, India, where we dug and poured home foundations for three families in need. Given the opportunity to combine my love for construction and my passion for helping those in need, I was certain that this was the senior project for me. I wanted the capstone of my college educational experience to reflect a hands-on approach, where I had the opportunity to make a difference and see an …

Bs News March/April

Building Services Engineering

No abstract provided.

Implementing Unbiased Decision-Making In Construction: A Lean Approach, Somik Ghosh, Michelle Robinette, Howard Tapia

The Professional Constructor

Construction project-teams are frequently faced with the task of decision-making as part of their responsibility. The positive effects of the decisions made at various stages of the projects lead to improved project performances, while negative effects can hinder the performances. The project teams take up the task of decision-making surrounded by multiple criteria, which can be arduous and clouded with subjectivity. This paper presents an approach based on the Lean principle of providing more autonomy to the project-teams and supporting collaborative and decentralized process in pursuit of unbiased decision-making. This Lean way of decision-making is formalized as Choosing by Advantage …

Attracting And Retaining Future Top Performing Employees: A Student Perspective, Julia Allen

The Professional Constructor

This essay provides insight as to how construction companies can both attract and retain top performing employees. By making the standard interview and recruiting processes more personal, construction companies can evaluate potential hires to see is they are a good fit for the company for years to come. Once employees are hired, companies then need to provide opportunities for both personal and professional growth. From personal experiences, I share the characteristics I find most important in an ideal employer and emphasize the importance of having an in-depth, genuine conversation with potential hires.

Attracting And Retaining Top Employees By Placing Proper Value On Their Contribution To The Company, Joseph Franklin Iii

The Professional Constructor

Due to an optimistic economic future, construction companies want to attract and retain the best employees to ensure company success. Because of a larger job market, employees now look for the optimal work values to be met in long-term employment opportunities. Construction companies have many challenges when attracting and retaining top employees in a growing market. Therefore; it is beneficial for employers to consider the evolving work values of employees and for these values to be promoted throughout company culture. Offering employees good value for their contribution to the company attracts and retains top employees.

Social Resources Of Mechanical Contracting Management Personnel, Blake Wentz, Sarabeth Gandara

The Professional Constructor

The construction industry in the United States is projected to grow faster than average compared to other industries through 2026. The Baby Boomer generation is leaving a significant gap in the labor force as they reach retirement. Retention of high quality management personnel is a priority for all companies in the construction industry, including mechanical contracting companies. Firms that fail to retain these employees will be left with an understaffed and underqualified workforce, which will hinder their ability to be competitive in the marketplace. In order to aid in retention efforts, mechanical contracting firms need to focus their attention on …

Essay Winners, American Institute Of Constructors

The Professional Constructor

No abstract provided.

Attracting And Retaining Future Top Performing Employees, Caleb Bardin

The Professional Constructor

The goal of this essay is to explore the key factors that influence top-performing employees’ decisions to change companies or remain with their current employers. A few of these factors are salary and benefits, work environment, and corporate advancement. This essay will address such factors and propose solutions using my own educational and professional experience. A key theme to note is the constant evaluation of employees and workplace environment by employers. No company can hope to be successful or have the best people if this skill is not enhanced and implemented well.

Study Of Various Construction Job Functions To Address Workforce Challenge, Abraham Bonilla, Dhaval Gajjar, Kenneth Sullivan

The Professional Constructor

Lack of construction workforce is one of the most predominant challenges faced by the construction industry. It is predicted that the industry will have a major shortage of skilled labor in the next decade due to the retirement of baby boomers and the lack of new talent entering the industry to replace these baby boomers. To attract young talent into the construction industry, it is critical to make them aware about the industry regarding various job functions as it relates to job satisfaction, compensation and career fulfilment. The purpose of this study is to gain insight of various construction job …

Consumer Perception And Willingness To Pay For Extended New Home Warranties, C. Todd Usher, Joseph M. Burgett

The Professional Constructor

Construction standards and methods for building new homes has improved over the last two decades resulting in significant improvements in energy efficiency, comfort, indoor air quality, and durability of new homes. Despite these improvements, the most common builder warranty for a new home in the United States ranges from 6 months to two years in duration. During the past two decades, manufacturer warranties on other durable goods such as automobiles has increased significantly. This study measures consumer perceptions of extended 12 year new home warranties with a survey completed by 162 adults in the United States. The results indicate that …

Ua1c2/37 Facilities Services & Heating Plant Photos, Wku Archives

WKU Archives Collection Inventories

Images of Facilities Services and the Heating Plant.

Ua66/9/1 Ogden College Of Science & Engineering Engineering Administration, Wku Archives

WKU Archives Collection Inventories

No abstract provided.

Efficient Excitation Of Micro/Nano Resonators And Their Higher Order Modes, N. Jaber, M. A. A. Hafiz, S. N. R. Kazmi, M. H. Hasan, F. Alsaleem, S. Ilyas, M. I. Younis

Durham School of Architectural Engineering and Construction: Faculty Publications

We demonstrate a simple and flexible technique to efficiently activate micro/nano-electromechanical systems (MEMS/NEMS) resonators at their fundamental and higher order vibration modes. The method is based on the utilization of the amplified voltage across an inductor, L, of an LC tank resonant circuit to actuate the MEMS/NEMS resonator. By matching the electrical and mechanical resonances, significant amplitude amplification is reported across the resonators terminals. We show experimentally amplitude amplification up to twelve times, which is demonstrated to efficiently excite several vibration modes of a microplate MEMS resonator and the fundamental mode of a NEMS resonator.

Method Of Monitoring Charge Condition Of Heat Pump System, Fadi M. Alsaleem, Gregg M. Hemmelgarn

Durham School of Architectural Engineering and Construction: Faculty Publications

A heat-pump circuit may include an indoor heat exchanger, an outdoor heat exchanger, a compressor adapted to circulate a working fluid between the indoor and outdoor heat exchangers, and an expansion device disposed between the indoor and outdoor heat exchangers. A monitor for the heat-pump system may include a return-air temperature sensor, a supply-air temperature sensor, and a processor. The return-air temperature sensor may be adapted to measure a first air temperature of air upstream of the indoor heat exchanger. The supply-air temperature sensor may be adapted to measure a second air temperature of air down stream of the indoor …

Voltage And Deflection Amplification Via Double Resonance Excitation In A Cantilever Microstructure, Mohammad H. Hasan, Fadi Alsaleem, Abdallah Ramini

Durham School of Architectural Engineering and Construction: Faculty Publications

Cantilever electrostatically-actuated resonators show great promise in sensing and actuating applications. However, the electrostatic actuation suffers from high-voltage actuation requirements and high noise low-amplitude signal-outputs which limit its applications. Here, we introduce a mixed-frequency signal for a cantilever-based resonator that triggers its mechanical and electrical resonances simultaneously, to overcome these limitations. A single linear RLC circuit cannot completely capture the response of the resonator under double resonance excitation. Therefore, we develop a coupled mechanical and electrical mathematical linearized model at different operation frequencies and validate this model experimentally. The double-resonance excitation results in a 21 times amplification of the voltage …

Benchmarking Image Processing Algorithms For Unmanned Aerial System-Assisted Crack Detection In Concrete Structures, Sattar Dorafshan, Robert J. Thomas, Marc Maguire

Durham School of Architectural Engineering and Construction: Faculty Publications

This paper summarizes the results of traditional image processing algorithms for detection of defects in concrete using images taken by Unmanned Aerial Systems (UASs). Such algorithms are useful for improving the accuracy of crack detection during autonomous inspection of bridges and other structures, and they have yet to be compared and evaluated on a dataset of concrete images taken by UAS. The authors created a generic image processing algorithm for crack detection, which included the major steps of filter design, edge detection, image enhancement, and segmentation, designed to uniformly compare dierent edge detectors. Edge detection was carried out by six …

Remotely Testing Whether A Climate Control System Controller Is Correctly Installed, Fadi M. Alsaleem

Durham School of Architectural Engineering and Construction: Faculty Publications

Disclosed are exemplary embodiments of apparatus and methods for remote testing of controllers such as thermostats, to detect incorrect climate control system configuration parameters . In an exemplary embodiment, a computer wirelessly connects with a remote thermostat and sends signal (s) to the thermostat instructing the thermostat to perform climate control function (s) in predefined sequence (s). The computer receives signal (s) from the thermostat indicating whether the thermostat is performing the climate control function (s) in accordance with the sent signal (s). Based on the signal (s) received from the thermostat, the computer determines whether the thermostat is configured …

Ua66/2 Ogden College Of Science & Engineering Architectural & Manufacturing Sciences, Wku Archives

WKU Archives Collection Inventories

Records created by the Architectural & Manufacturing Sciences.

Files are arranged in the following subseries:

1. Administration
2. Publications
3. Centers & Institutes

Need For Aeromedical Evacuation High-Level Containment Transport Guidelines, Shawn G. Gibbs, Jocelyn J. Herstein, Aurora B. Le, Elizabeth L. Beam, Theodore J. Cieslak, James V. Lawler, Joshua L. Santarpia, Terry L. Stentz, Kelli R. Kopocis-Herstein, Chandran Achutan, Gary W. Carter, John J. Lowe

Durham School of Architectural Engineering and Construction: Faculty Publications

Circumstances exist that call for the aeromedical evacuation high-level containment transport (AE-HLCT) of patients with highly hazardous communicable diseases. A small number of organizations maintain AE-HLCT capabilities, and little is publicly available regarding the practices. The time is ripe for the development of standards and consensus guidelines involving AE-HLCT.

Hvac System Remote Monitoring And Diagnosis, Jeffrey N. Arensmeier, Gregg M. Hemmelgarn, Fadi M. Alsaleem, Priotomo Abiprojo

Durham School of Architectural Engineering and Construction: Faculty Publications

A monitoring system for an HVAC system of a building includes a monitoring server located remotely from the building. The monitoring server receives, from a device installed at the building, (i) time-domain current data based on a measured aggregate current supplied to a plurality of components of the HVAC system, and (ii) data based on frequency-domain current data of the measured aggregate current. Based on the received data, the monitoring server accesses (i) whether a failure has occurred in a first com ponent of the plurality of components and (ii) generates a preliminary advisory in response to determining that the …

Strategies And Resources For Government Agencies To Utilize Disadvantaged Business Enterprises In Transportation Design-Build Projects, Baabak Ashuri, Adjo Amekudzi-Kennedy, Stephanie Amoaning-Yankson, Yunping Liang, Yang Cao

Durham School of Architectural Engineering and Construction: Faculty Publications

The Disadvantaged Business Enterprise (DBE) Program was established to provide opportunities for businesses owned and controlled by socially and economically disadvantaged individuals, such as minority-owned and women-owned businesses, to participate in federally funded transportation-related projects. Such DBE participation has increasingly been achieved over the years with the appropriate guidance for traditional project delivery: design-bid-build. However, in recent times the onset of alternative project delivery methods, such as design-build (DB), has introduced challenges for state DOTs trying to implement the DBE program using traditional approaches. This paper presents a synthesis of strategies and resources being used in state DOTs to achieve …

Skip This Chore: Cleaning Your Air Conditioner Condenser Probably Won't Make It Work Better, David Yuill

Durham School of Architectural Engineering and Construction: Faculty Publications

I asked my neighbor who hoses off his air conditioner condenser every spring why he does it. “Because my dad always told me I had to,” he said.

Conventional wisdom like what my neighbor’s dad imparted may always seem right. But through my HVAC scholarship – the study of heating, ventilation and air-conditioning systems – I’ve learned that this particular presumption is probably wrong.

Heat Pump And Air Conditioning Grading Systems And Methods, Fadi Mohammad Alsaleem

Durham School of Architectural Engineering and Construction: Faculty Publications

An expectation module determines an expected average power consumption of a heat pump for a predetermined period as a function of indoor and outdoor temperatures of the building during the predetermined period. A difference module determines a power difference between an average power consumption of the heat pump during the predeter mined period and the expected average power consumption of the heat pump for the predetermined period. A grade determination module determines a grade of the heat pump for the predetermined period based on the power difference of the predetermined period. A reporting module generates a displayable report including the …

Building Envelope And Interior Grading Systems And Methods, Fadi Mohammad Alsaleem

Durham School of Architectural Engineering and Construction: Faculty Publications

A difference module determines differences between an outdoor ambient temperature and an indoor temperature, determines a first average of the differences , and determines a second average of the differences. A storing module stores a first data point, the first data point including the first average and a first total run time of a heating, ventilation, and/or air conditioning (HVAC) system, and stores a second data point, the second data point including the second average and a second total run time of the HVAC system. A fitting module fits a line to the first and second data points. An envelope …

Passive Cooling In Non-Residential Nearly Zero Energy Buildings: A Thermal Comfort Analysis Based On Measurement, Modelling And Simulation, Adam O'Donovan

Theses

Overheating in non-residential nearly zero energy buildings (nZEBs) presents a major risk to the well-being, productivity and thermal satisfaction of the people who occupy them. As global temperatures are expected to increase in the future, the overheating risk and cooling demand is also expected to increase. Therefore, low cost and low energy solutions that are able to maintain thermally comfortable conditions without the need for mechanical systems will be vital in decarbonising the building stock and ensuring that buildings are comfortable and remain low carbon now and in the future. Passive cooling has long been championed as a low cost …

Experiencing Extreme Height For The First Time: The Influence Of Height, Self-Judgment Of Fear And A Moving Structural Beam On The Heart Rate And Postural Sway During The Quiet Stance, Mahmoud Habibnezhad, Jay Puckett, M. S. Fardhosseini, Houtan Jebelli, Terry Stentz, L. A. Pratama

Durham School of Architectural Engineering and Construction: Faculty Publications

Falling from elevated surfaces is the main cause of death and injury at construction sites. Based on the Bureau of Labor Statistics (BLS) reports, an average of nearly three workers per day suffer fatal injuries from falling. Studies show that postural instability is the foremost cause of this disproportional falling rate. To study what affects the postural stability of construction workers, we conducted a series of experiments in the virtual reality (VR). Twelve healthy adults—all students at the University of Nebraska-Lincoln—were recruited for this study. During each trial, participants’ heart rates and postural sways were measured as the dependent factors. …