Digital Commons Network^™

Strength Comparison For Fully Dense Zirconium Diboride Ceramics Tested By Different Methods, Darko Kosanović, Suzana Filipović, Isaak Trajković, Nina Obradović, Paul M. Brune, Gregory E. Hilmas, William G. Fahrenholtz

Materials Science and Engineering Faculty Research & Creative Works

The strength of zirconium diboride ceramics was tested by three different methods, 3-point flexure, 4-point flexure, and compression. Nearly full-density ceramics were obtained by hot pressing commercial ZrB₂ powder with the addition of.5 wt.% carbon as a sintering aid. The thermal properties and hardness were studied for ZrB₂ milled with ZrB₂ and WC media. Based on phase purity and higher thermal conductivity, ZrB₂ ceramics prepared from powders milled with ZrB₂ media were selected for mechanical property studies. The strength in 3-point flexure was 546 ± 55 MPa. The flexure strength was 476 ± 41 MPa …

Experimental Investigation Of A Viscoelastic Liner To Reduce Under Helmet Overpressures And Shock Wave Reflections, Cody J.H. Thomas, Fatih Dogan, Catherine E. Johnson

Materials Science and Engineering Faculty Research & Creative Works

Introduction: Shock wave overpressure exposures can result in blast-induced traumatic brain injury (bTBI) in warfighters. Although combat helmets provide protection against blunt impacts, the protection against blast waves is limited due to the observed high overpressures occurring underneath the helmet. One route to enhance these helmets is by incorporating viscoelastic materials into the helmet designs, reducing pressures imposed on the head. This study aims to further investigate this mitigation technique against under-helmet overpressures by adding a viscoelastic liner to the inside of a combat helmet. Methods: The liner's effectiveness was evaluated by exposing it to free-field blasts of Composition C-4 …

Segmented Fiber Optic Sensors Based On Hybrid Microwave-Photonic Interrogation, Wassana Naku, Osamah Alsalman, Jie Huang, Chen Zhu

Electrical and Computer Engineering Faculty Research & Creative Works

In this paper, we propose and demonstrate a novel concept of segmented fiber optic sensors by integrating the fiber Bragg grating (FBG) reflector modality and a hybrid interrogation technique enabled by microwave photonics. As a proof of concept, a radiofrequency Fabry-Perot interferometer (FPI) based on an optical fiber with two FBGs as the two reflectors of the Fabry-Perot (FP) cavity is constructed. By measuring the frequency response of the FPI device followed by a joint-time-frequency-domain analysis, the interferogram of the FPI in the microwave domain and the time-domain signal of the FBGs can be unambiguously reconstructed. Thus, the two elements …

A Novel Physics-Assisted Genetic Algorithm For Decoupling Capacitor Optimization, Li Jiang, Ling Zhang, Shurun Tan, Da Li, Chulsoon Hwang, Jun Fan, Er Ping Li

Electrical and Computer Engineering Faculty Research & Creative Works

This article proposes a new physics-assisted genetic algorithm (PAGA) for decoupling capacitor (decap) optimization in power distribution networks (PDNs), which is a highly efficient approach to minimizing the number of decaps within an enormous search space. In the proposed PAGA method, the priority of the decap ports is first determined based on their physical loop inductances. Then, an initial solution is quickly obtained by placing decaps sequentially on the port with the highest priority. Subsequently, a GA with prior physical knowledge is developed to find better decap solutions progressively. A port removal scheme that eliminates the low-priority ports and a …

Electromagnetic-Circuital-Thermal-Mechanical Multiphysics Numerical Simulation Method For Microwave Circuits, Huan Huan Zhang, Zheng Lang Jia, Peng Fei Zhang, Ying Liu, Li Jun Jiang, Da Zhi Ding

Electrical and Computer Engineering Faculty Research & Creative Works

An electromagnetic-circuital-thermal-mechanical Multiphysics numerical method is proposed for the simulation of microwave circuits. The discontinuous Galerkin time-domain (DGTD) method is adopted for electromagnetic simulation. The time-domain finite element method (FEM) is utilized for thermal simulation. The circuit equation is applied for circuit simulation. The mechanical simulation is also carried out by FEM method. A flexible and unified Multiphysics field coupling mechanism is constructed to cover various electromagnetic, circuital, thermal and mechanical Multiphysics coupling scenarios. Finally, three numerical examples emulating outer space environment, intense electromagnetic pulse (EMP) injection and high-power microwave (HPM) illumination are utilized to demonstrate the accuracy, efficiency, and …

Ultra-Fast Annealing Improves Snr And Long-Term Stability Of A Highly Multiplexed Line-By-Line Fbg Array Inscribed By Femtosecond Laser In A Coreless Fiber For Extreme-Temperature Applications, Farhan Mumtaz, Bohong Zhang, Jeffrey D. Smith, Ronald J. O'Malley, Rex E. Gerald, Jie Huang

Electrical and Computer Engineering Faculty Research & Creative Works

This study reports the fabrication of an 4th-order line-by-line Fiber Bragg Gratings (FBG) array using femtosecond laser inscription within a highly multimode coreless optical fiber, with a particular focus on achieving substantial multiplexing capabilities. An ultra-fast annealing procedure is employed, resulting in an impressive enhancement of the FBG sensor's fringe visibility by approximately 13 dB, signifying a notable improvement of approximately ~4 dB. This substantial enhancement contributes to the long-term stability and performance of the multiplexed FBG array in extreme temperature conditions. The systematic fabrication approach employed for the multiplexed FBG array guarantees a high signal-to-noise ratio (SNR) for each …

Modeling Of Power Distrubition Network (Pdn) Noise Coupling Induced Clock Phase Noise, Zhekun Peng, Junyong Park, Chaofeng Li, Joey Stecher, Srinivas Venkataraman, Xu Wang, Granthana Rangaswamy, Donghyun Kim

Electrical and Computer Engineering Faculty Research & Creative Works

Phase noise analysis is important to clock design. Noise sources of spurs shown on the phase noise result are challenging to find out due to the unknown source locations and coupling mechanisms. Noise from power distribution network (PDN) is one of the most troublesome sources. A behavioral modeling methodology is proposed to simulate the clock phase noise induced by PDN noise coupling for two different mechanisms: PDN-to-clock additive coupling and PDN-to-PDN up-conversion modulation. The thermal noise and 1/f flicker noise are simplified to provide a straightforward view of spur level. The model can be applied to both single-ended clock and …

Ai Trustworthy: Ethical Challenges And Strategies, Jian Liu, Iwan Sandjaja, Donald C. Wunsch

Electrical and Computer Engineering Faculty Research & Creative Works

This paper explores the pivotal role of trust in the widespread application of Artificial Intelligence (AI) across various domains. We review AI applications in sectors like energy, healthcare, and autonomous vehicles and discuss the crisis of human trust they face. This paper introduces a novel framework that delineates the relationship between AI transparency and user trust, highlighting specific industry applications. Through a systematic review of recent literature, we first delve into factors such as emotional response, acceptance, transparency, accuracy, and interpretability that shape human trust in AI. We then underscore the necessity of ethical AI practices and highlight the importance …

Highly Sensitive Liquid-Level Sensing Based On Microwave Frequency Domain Reflectometry And Interferometry, Chen Zhu, Osamah Alsalman, Jie Huang

Electrical and Computer Engineering Faculty Research & Creative Works

Frequency domain reflectometry (FDR) and interferometry are two widely used investigative techniques that have been instrumented using optical and microwave devices for a diverse array of sensing applications. In this paper, we present a highly sensitive liquid-level sensor using a custom hollow coaxial cable transmission line. Measurements of liquid levels with high sensitivity and resolution can be achieved by both FDR and interferometry-based measurements using the same sensor device. We show that FDR-based measurements are more straightforward for liquid-level sensing and are suitable for both small and large variations of liquid level, while interferometry-based measurements provide slightly higher measurement resolution …

Frailty Knowledge, Training And Barriers To Frailty Management: A National Cross-Sectional Survey Of Health Professionals In Australia, Leila S. Hanjani, Sarah Fox, Ruth E. Hubbard, Emily Gordon, Natasha Reid, Sarah N. Hilmer, Rosemary Saunders, Danijela Gnjidic, Adrienne Young

Research outputs 2022 to 2026

Objective(s): To understand Australian health professionals' perceptions of their knowledge and previous training about frailty, as well as barriers to frailty assessment and management in their practice. Methods: A cross-sectional online survey was developed and distributed to health professionals (medical, nursing and allied health) engaged in clinical practice in Australia through convenience and snowball sampling techniques from March to May 2022. The survey consisted of five sections: frailty training and knowledge; confidence in recognising and managing adults with frailty; the importance and relevance of frailty; barriers to assessing and managing frailty in practice; and interest in further frailty training. Responses …

Nasoalveolar Molding: A Rise In Early Management Of Newborn Patient With Cleft Lip And Palate, Reeya Agrawal, Pallavi Daigavane, Amit Reche

International Arab Journal of Dentistry

Orofacial clefts are one of the most frequent congenital oral and maxillofacial abnormalities. When these babies are roughly three months old, lip rebuilding, also known as cheiloplasty, is a critical concern. In several cleft facilities, To improve the treatment success, presurgical Nasoalveolar Molding (NAM) has been included in the therapy protocol. In patients with cleft lip and palate, this technique is routinely used to bring the alveolar segments into normal alignment and improve nasal symmetry. In this article, the benefits of using this method as part of a treatment plan for infants with cleft lip and palate will be described. …

Does Reduced Taper Canal Preparation Increase The Load Capacity Of Endodontically Treated Teeth?, Mostafa M.A. Elkholy, Omar Mahmoud Noureldin, Hala Fayek Khalil, Shehabeldin M. Saber

International Arab Journal of Dentistry

Objectives: The aim of this in-vitro study is to assess and compare the load capacity of teeth with canals prepared using progressive taper versus regressive taper.

Methods: Twenty-seven extracted mandibular molars were categorized into three equal groups. The negative control group involved teeth that were accessed and restored with composite resin without canal preparation. The regressive canal preparation group used the TruNatomy file system, while the progressive canal preparation group employed the ProTaper Gold system. Subsequently, all samples underwent loading using a universal testing machine until tooth fracture occurred. The force required to fracture each tooth was recorded …

Quantitative Comparison Of Presenilin Protein Expression Reveals Greater Activity Of Ps2-Γ-Secretase, Melissa K. Eccles, Nathan Main, Rodrigo Carlessi, Ayeisha M. Armstrong, Miheer Sabale, Brigid Roberts-Mok, Janina E. E. Tirnitz-Parker, Mark Agostino, David Groth, Paul E. Fraser, Giuseppe Verdile

Research outputs 2022 to 2026

γ-secretase processing of amyloid precursor protein (APP) has long been of interest in the pathological progression of Alzheimer's disease (AD) due to its role in the generation of amyloid- . The catalytic component of the enzyme is the presenilins of which there are two homologues, Presenilin-1 (PS1) and Presenilin-2 (PS2). The field has focussed on the PS1 form of this enzyme, as it is typically considered the more active at APP processing. However, much of this work has been completed without appropriate consideration of the specific levels of protein expression of PS1 and PS2. We propose that expression is an …

Dna Origami-Assisted Regioselective Organization Of Anisotropic Gold Nanotriangle Clusters, Wenyan Liu, Prashant Gupta, Yuwei Zhang, Krishna Thapa, Srikanth Singamaneni, Risheng Wang

Chemistry Faculty Research & Creative Works

The manipulation of anisotropic nanoparticles, such as gold nanorods and nano prisms, has attracted great attention in nanotechnology due to their sensitive geometry-dependent properties. However. traditional synthesis and assembly methods for these particles face challenges in size uniformity and higher-order structuring. To address these limitations, this study presents a strategy using DNA origami triangles, not just as templates, but as encapsulating agents for gold nanotriangles (AuNTs). This method enables the construction of diverse nanoparticle clusters with precisely controlled distance and orientation. The formed clusters exhibit unique optical characteristics, demonstrated by UV-visible spectroscopy and supported by finite-difference time domain (FDTD) simulations. …

High-Capacity Anode For Sodium-Ion Batteries Using Hard Carbons Derived From Polyurea-Cross-Linked Silica Xerogel Powders, Santhoshkumar Sundaramoorthy, Rushi U. Soni, Stephen Yaw Owusu, Sutapa Bhattacharya, A. B.M.Shaheen Ud Doulah, Vaibhav A. Edlabadkar, Chariklia Sotiriou-Leventis, Amitava Choudhury

Chemistry Faculty Research & Creative Works

In this article, we demonstrated carbon aerogel-silica composites derived from polyurea-cross-linked silica xerogel powders (C-PUA@silica) as anodes for Na-ion batteries. These xerogel-derived hard carbons with embedded silica showed a stable high capacity. Of the several hard carbon samples derived at different temperatures, the pyrolyzed sample at 800 °C (C-PUA@silica-800) showed a high capacity of 236 mAh/g at a current density of 10 mA/g and a stable cycle-life at 200 mAh/g. The galvanostatic charge-discharge curves displayed a sloping voltage profile reminiscent of the adsorption mechanism of Na+ storage. On the other hand, higher temperature-pyrolyzed samples at 1300 °C (C-PUA@silica-1300) displayed a …

Boosting The Microbial Electrosynthesis Of Formate By Shewanella Oneidensis Mr-1 With An Ionic Liquid Cosolvent, Ashwini Dantanarayana, Wassim El Housseini, Kevin Beaver, Monica Brachi, Timothy P. Mcfadden, Shelley D. Minteer

Chemistry Faculty Research & Creative Works

Microbial electrosynthesis (MES) is a rapidly growing technology at the forefront of sustainable chemistry, leveraging the ability of microorganisms to catalyze electrochemical reactions to synthesize valuable compounds from renewable energy sources. The reduction of CO₂ is a major target application for MES, but research in this area has been stifled, especially with the use of direct electron transfer (DET)-based microbial systems. The major fundamental hurdle that needs to be overcome is the low efficiency of CO₂ reduction largely attributed to minimal microbial access to CO₂ owing to its low solubility in the electrolyte. With their tunable physical …

Selected Trace Element Uptake By Rice Grain As Affected By Soil Arsenic, Water Management And Cultivar -A Field Investigation, Eric M. Farrow, Jianmin Wang, Honglan Shi, John Yang, Bin Hua, Baolin Deng

Chemistry Faculty Research & Creative Works

Accumulation of arsenic (As) in rice grain was reported in many regions of the world, including the United States, which has been a threat to human health. This field research investigated the grain as accumulation and its relationship with the uptake of selenium (Se), molybdenum (Mo), and cadmium (Cd) in soils with and without monosodium methane arsonate (MSMA) amended, as effects of selected rice cultivars and water management. Results indicated that MSMA increased the accumulation of as and Se but decreased Mo for all six cultivars under four irrigation management. MSMA also increased grain-Cd in some cultivars. in no MSMA-amended …

A Super-Hard High Entropy Boride Containing Hf, Mo, Ti, V, And W, Suzana Filipovic, Nina Obradovic, Greg E. Hilmas, William G. Fahrenholtz, Donald W. Brenner, Jon Paul Maria, Douglas E. Wolfe, Eva Zurek, Xiomara Campilongo, Stefano Curtarolo

Materials Science and Engineering Faculty Research & Creative Works

Super-Hard (Hf,Mo,Ti,V,W)B2 Was Synthesized by Boro-Carbothermal Reduction and Densified by Spark Plasma Sintering. This Composition Was Produced for the First Time as a Single-Phase Ceramic in the Present Research. the Optimized Ceramic Had a Single Hexagonal AlB2-Type Crystalline Phase with a Grain Size of 3.8 µm and Homogeneous Distribution of the Constituent Metals. the Vickers Hardness Exhibited the Indentation Size Effect, Increasing from 27 GPa at a Load of 9.8 N to as High as 66 GPa at a Load of 0.49 N. This is the Highest Hardness Reported to Date for High Entropy Boride Ceramics.

Injectable Dendrimer Hydrogel Delivers Melphalan In Both Conjugated And Free Forms For Retinoblastoma, Remy C. Cooper, Juan Wang, Hu Yang

Chemical and Biochemical Engineering Faculty Research & Creative Works

We report the successful synthesis of an injectable dendrimer hydrogel (DH) carrying melphalan, a clinical drug for retinoblastoma treatment, in both conjugated and free forms. Polyamidoamine (PAMAM) dendrimer generation 5 (G5) is surface-modified with an acid-sensitive acetal-dibenzocyclooctyne linker and then undergoes azide-alkyne cycloaddition with melphalan-PEG-N3 conjugate to form G5-acetal-melphalan. During the DH gelation between G5-acetal-melphalan and PEG-diacrylate, free melphalan is added, resulting in a hydrogel (G5-acetal-melphalan-DH/melphalan) that carries the drug in both conjugated and free forms. Melphalan is slowly released from G5-acetal-melphalan-DH/melphalan, with the conjugated melphalan released more quickly at pH 5.3 due to acid-triggered acetal bond cleavage. The formulation's …

Transitioning To A Lower Global Warming Refrigerant, A Performance Study Of R-513a And Hfc-134a In Commercial Chillers, Hossein Abedsoltan, Mark B. Shiflett

Chemical and Biochemical Engineering Faculty Research & Creative Works

The performance of R-513A and HFC-134a refrigerants is compared in two identical chillers operating at the University of Kansas. R-513A is a more environmentally friendly refrigerant due to its lower global warming potential that can be used as a retrofit replacement for HFC-134a in chillers. This study investigates the performance comparison of transitioning from HFC-134a to R-513A. The chillers have been in operation for two years, and cooling capacity, coefficient of performance, and other operating parameters are compared under similar cooling conditions. Cooling capacities ranged from 100 to 500 kW for both chillers. Overall, the energy consumption and coefficient of …

Information Extraction From The Reviews Of Ai Applications Using Sas Text Mining Process, Imranul Kabir Chowdhury, Wen Bin Yu

Business and Information Technology Faculty Research & Creative Works

The recent surge in AI advancements, particularly generative AI, has grabbed the attention of major tech companies who are all striving to integrate it seamlessly into their products. This highlights the need to evaluate the various AI products on the market and identify the features that resonate most with users. SAS Enterprise Miner, a powerful text analysis tool, can be used to uncover hidden insights from user reviews. In this study, we will leverage various SAS functions to analyze reviews of different AI applications. By analyzing these reviews, we aim to pinpoint the unique strengths of these AI applications and …

The Potential Effects Of Abiotic Stresses On Ziziphus And Acacia Species Grown Under Uae Climate Condition, Almaha Abdulla Alneyadi

Theses

This comprehensive thesis delves into a comparative analysis of two prominent desert plant species, namely Acacia and Ziziphus, shedding light on their distinct adaptive features in response to challenging environmental conditions. The exploration spans various facets, including the germination process, tap root development, and their reactions to water stress, ultimately revealing the superior hardiness and adaptability of Acacia over Ziziphus. In the realm of germination, Acacia stands out with its swift and efficient initiation, indicating a robust mechanism for establishing its presence in arid landscapes. The examination of tap root development further underscores the resilience of Acacia, as it demonstrates …

Summer Vacation Activity Manual, Aisha Naz Ansari, Sadia Muzaffar Bhutta, Zarfin Saleem, Sohail Ahmad

Institute for Educational Development Pakistan (IED-PK) Archives

A guidebook with a compilation of activities to help parents/caregivers boost the holistic development of children during summer vacations.

Bioprinting With Adipose Stem Cells And Hydrogel Modified With Bioactive Glass, Krishna C.R. Kolan, Apurv Saxena, Bradley A. Bromet, Lesa B. Steen, August T. Bindbeutel, Julie A. Semon, Delbert E. Day, Ming C. Leu

Biological Sciences Faculty Research & Creative Works

Bioprinting research is focused on utilizing growth factors and multiple cell types to create clinically relevant three-dimensional (3D) tissue models using hydrogels. Rheological and biological challenges are two main factors that limit the creation of extrudable bioactive hydrogels. In this study, we investigate incorporation of fast dissolving and bioactive borate glass in different weight to volume percentages (0.075 to 0.6%) to alginate-gelatin (1:1) hydrogel to improve rheological properties and enable bioprinting with bioactive glass. The addition of glass improved the stiffness of the hydrogel. Human adipose-derived mesenchymal stem cells (ASCs) were uniformly mixed in this bioink at 1 x 106 …

Conscientious Objection And Abortion: The Italian Pseudo-Exceptionalism, C. Crea

FIU Law Review

Threats to abortion and reproductive rights are well-rooted in global discursive and strategic practices promoted by conservative and ‘pro-life’ movements and narratives. Starting from these premises, this essay will focus on abortion access in Italy and the barrier caused by conscientious objection among medical personnel, which appears indefensible in light of both international human rights regimes and philosophical-theoretical perspectives. The main questions explored here are the following: Is conscientious objection to abortion really based on Catholic moral teaching, which constitutes the conventional religious wisdom of the national societal fabric? How and to what extent are Catholic and conservative moral narratives …

Ai And English Language Teaching: Affordances And Challenges, Helen Crompton, Adam Edmett, Neenaz Ichaporia, Diane Burke

STEMPS Faculty Publications

English is one of the most used languages for jobs, markets, tourism, discourse and international connectivity. However, English learners face many challenges in gaining English language skills. Extant studies show that AI has affordances to support in English language teaching and learning ELT/L. This study answers the call to examine specific challenges and affordances for using AI in ELT/L. A systematic review method was used with PRISMA principles to identify 42 studies. Findings reveal the geographical locations of studies, learner ages and years of study. Grounded coding was then used to identify affordances of the use of AI in ELT/L …

Exploring Instructional Designers' Utilization And Perspectives On Generative Ai Tools: A Mixed Methods Study, Tian Luo, Pauline S. Muljana, Xinyue Ren, Dara Young

STEMPS Faculty Publications

The emergence of generative artificial intelligence (GenAI) has caused significant disruptions on a global scale in various workplace settings, including the field of instructional design (ID). Given the paucity of research investigating the impact of GenAI on ID work, we conducted a mixed methods study to understand instructional designers (IDs)’ perceptions and experiences of utilizing GenAI across a spectrum of ID tasks. A total of 70 IDs completed an online survey, and 13 of them participated in the semi-structured interviews. The survey results indicated IDs’ familiarity with and perceived usability of GenAI tools in performing various ID responsibilities in their …

Information Literacy Reflected Through Awareness And Use Of Information Among Sarpanches In Punjab During Covid, Poonam Saini, Satwinderpal Kaur Gill

Library Philosophy and Practice (e-journal)

This study attempts to examine the Information Literacy skills of Sarpanches during Covid-19 in Punjab. The main objectives of the study are to explore information needs, use of information sources and general awareness of Sarpanches during the Pandemic. Survey method was used to collect data from 103 sarpanches of different districts of Punjab with the help of a self-structured questionnaire. The study found that sarpanches have shown good Information Literacy skills during Pandemic. They were well informed and aware about different aspects of Covid-19 such as origin, safety measures, government instructions etc. State government was also successful to achieve its …

The Forthcoming General Election In The Republic Of Ireland: Winds Of (Left-Wing) Change Or Plus Ça Change?, Chris O'Ralaigh

Articles

The forthcoming general election will be the most consequential electoral contest for the Republic of Ireland in a century. The polity is situated in truly novel territory with the potential for an historic first: the incoming of a Sinn Féin-led, left-wing government. Any such government would portend change in the North of Ireland, symbolising a critical juncture on the path towards the ending of partition. Analysing electoral and ideological shifts across the post-2008 period, this article examines the immediate prospects for the coming to power of a left-wing government and an historic first in Irish politics.

Shaping Socially Engaged Art Practice And Critical Pedagogy In The Uk Arts And Cultural Sector: An Auto/Biographical Framing Of Class, Gender And Political Activism, Chrissie Tiller

Doctoral

Situated at the intersection of critical pedagogy, radical theatre and political activism, this PhD thesis reflects critically on a series of publications and an interdisciplinary counterhegemonic socially engaged art practice between 2010-20. Mobilising the auto/biographical as a conceptual framework for critical analysis, the thesis addresses questions of systemic inequalities, cultural democracy and social transformation in the UK arts and cultural sector. By examining my lived experience through the analytical lenses of intersectionality and feminist standpoint theory, the thesis foregrounds how interconnecting oppressions of gender and class have contributed to the formation of my creative practice and its pedagogical interventions, constituting …