Digital Commons Network^™

Corrosion Resistance Of The Chromium-Manganese-Nickel And Chromium-Manganese Austenitic Stainless Steels, Robert Dewitt Merrick

Theses

The corrosion resistance of the chromium-manganese-nickel austenitic stainless steels has been established through a study of the available literature and unpublished data obtained from producers and users of these alloys. Several compositions are available as listed below. DESIGNATIONCOMPOSITION % CMnCrNiNAISI 2010.155.5/7.516.0/18.03.5/5.50.25AISI 2020.157.5/10.017.0/19.04.0/6.00.25CM0.1513.0/18.014.0/17.01.00.25Tenelon0.1014.517-0.40TRC0.0816.515.0 min.1.00.2CMN0.651225-0.452040.087.5/10.017.0/19.04.0/6.00.25

The AISI Type 201 and 202 alloys have been listed by the American Iron and Steel Institute.

The development and application of these alloys was necessary because of the increasing shortage of nickel and the wide use of the chromium-nickel austenitic stainless steels. The chromium-nickel steels are used in a wide variety of consumer items and are …

The Thermal Conductivity And Other Properties Of Carbonaceous Briquettes, Alfred Seymour Bien, Oliver Phillips

Theses

Anthracite, bituminous coal and petroleum fluid coke were briquetted under pressures of 1000, 2000, 3000, 1000 and 5000 pounds per square inch, using coal tar pitch and petroleum coke bottoms as binding agents.

The individual briquettes were then carbonized. The temperatures of carbonization were 400°, 700°, 1000°, 1300°, 1600° and 1769°F. The effects of carbonization on the specific gravity and weight and volume changes as a function of carbonizing temperature were studied.

The thermal conductivities of the briquettes were determined in a modified guarded hot plate conductivity cell. The temperature of the determination was such that the hot side temperature …

Rigid, Unplasticized, Polyvinyl Chloride Piping : An Engineering Material Study, James Patrick Kelleher

Theses

Rigid, unplasticized, polyvinyl chloride is one of several thermoplastic materials which can be made available on a reasonable, commercial basis in the form of pipe, as well as in other forms necessary for the assembly of a complete piping system.

These materials offer resistance to widely varying conditions of environment, light weight, relatively low cost, ease and economy of installation, self-insulating characteristics, minimum solid-deposit tendency, and low frictional losses. On the other hand, these materials have lower mechanical properties than most metals, and these properties are subject to wider variations as a function of temperature.

Of the thermoplastic piping materials …

Thermodynamic Properties Of 3-Methylpentane, Raymond Ralph Bernabei

Theses

The thermodynamic properties of 3-Methylpentane have been evaluated at temperatures from 32°F to 550°F and from the saturation pressure to 300 atmospheres based on available experimental data. The generalized thermodynamic correlations of Hougen, Lydersen and Greenkorn were used to evaluate the thermodynamic properties in the superheated range. An equation relating the ideal gas specific heat and temperature has been derived for the range in which no experimental data were available. Values for pressure, specific volume, temperature, enthalpy and entropy have been presented in the form of tables and/or graphs.

Heat Transfer Coefficients Of Condensing Vapors, James Joseph Broderick, Harold E. Devaney

Theses

Several experimental methods have been developed for the determination of the rate of heat transfer between a pure condensing organic vapor and a cold surface. The experimental results of the earliest method, the so-called "embedded thermocouple" approach, have not been in good agreement with heat transfer values predicted by the theoretical Nusselt equation, nor has good agreement been found among the individual data, The alternate method was an indirect approach developed by Wilson and was based on the effect of cooling watt r velocity. Wilson's method provided values in close agreement with the values predicted by the Nussalt equation but …

Vapor-Liquid Equilibria, Vincent De Paul Brown

Theses

The thesis was undertaken for the purpose of testing available experimental vapor-liquid equilibrium data for thermodynamic consistency, with a view to finding an intercorrelation of the activity coefficient-concentration curves, for different groups of systems, as a function of the intercepts. It was hoped that a correlation using molar volumes, parachor volumes, or molecular weights would be developed which could be explained on the basis of hydrogen bonding.

The Redlich and Kister^{1 equations were used to smooth the experimental data and to obtain values for the constants B, C and D. Redlich and Kister state that these constants serve as …}

A Study In Diffusion, Nicholas James Driscoll

Theses

The object of this thesis was to build an experimental apparatus and to study the diffusion of crystal violet in ethanol-water mixtures and diacetone alcohol-water mixtures. In order to validate experimental technique and to check the work of Mouquin Cathcart(1) who postulated compouhd formation in ethanol-water based on diffusion studies, experiments were conducted on the ethanol-water system in the area where compound formation was predicted.

In order to check the proposal of Konrad(2), based on studies of the heats of mixing that compound formation occurs between diacetone alcohol and water, studies were made on the diffusion of crystal violet in …

A Study Of The Mixed Acid Nitration Of 2-Amino-5-Chloropyridine, Harold Edward Ehrenbeck

Theses

The mixed-acid nitration of 2-amino-5-chloropyridine has been studied and improvements in yield and quality made.

2-Nitramino-5-chloropyridine has been prepared in high purity with a yield of 87.5%, an improvement over the results of Stokes, who reported 80.0%, and Harris, who reported 63.0%, as their best yields. The quality of the product, as indicated by melting points, has been increased.

This improvement involves the addition of 2-amino-5-chloropyridine to a pre-mixed nitrating acid. This nitrating acid consists of sulfuric acid and nitric acid. The composition is based on an optimum nitric ratio of 1.04, and an optimum D.V.S. of 2.25.

The Condensation Of Vapors From Gas - Vapor Mixtures, Lewis George King, Walter Andrew Blumenscheid

Theses

Superheated mixtures of cyclohexane vapor and nitrogen and benzene vapor and nitrogen were passed at various flow rates downward through a vertical double pipe condenser with cooling water flawing counter-currently in an annular space.

The method of Colburn and Hougen for the design of cooler-condensers was used to compare predicted heat transfer area to the experimental heat transfer area. Based on the ay-stems investigated, limits of accuracy of the predicted heat transfer areas were set as a function of inlet and cutlet Reynolds numbers. A suggested modification of the Colburn-Hougen correlation was made to extend the limits of accuracy. It …

Kinetics Of Chromium-Hydrogen Ion Exchange, Frank Joseph Klosowski, Alfred John Meinhardt

Theses

In this investigation the rates of trivalent-univalent cation exchange in a stirred batch reactor for the chromic ion-Dovex 50 system have been measured. The progress of the reaction has been followed continuously by measuring the change in hydrogen ion concentration of the bulk solution as a function of time with a Beckman pH Meter having external electrodes immersed in the reaction mixture.

This work has been undertaken to determine the rate-controlling mechanism of the reaction, and the influence of agitator speed, particle size, and solution concentration on the rate of exchange. Agitator speed. studied, as limited by the equipment, are …

Measurement Of The Specific Surface Of Perlite, Richard Gordon Lamborn, Carl Henry Vogel

Theses

A low temperature gas adsorption apparatus was designed for the purpose of measuring the total surface area of solids using the well known B.E.T. method.

The apparatus was designed so that several different gases could be used as adsorbates without evacuating the gas reservoirs each time a different adsorbate was to be used. This was accomplished by providing three gas reservoirs of sufficient capacity to allow several determinations to be made at moderate initial reservoir pressures of from two to three pounds per square inch. A separate bulb and manometer system was supplied for determining the saturation pressures of adsorbates …

Equilibria In The Esterification Of Boric Acid, Richard William Palizay

Theses

A solvent extraction method was developed to determine the equilibria in the esterification of boric acid, In this method boric acid was reacted with various alcohols. After equilibrium was reached, the ester was isolated from the reaction mixture by means of a solvent and the amount of ester determined quantitatively. The equilibrium constants were then calculated for the reaction of boric acid with several alcohols.

Zone Refining Of Anthracene, Charles Poultney Perot

Theses

The process of zone refining involves the passage of a molten zone along a rod of solid. As the zone progresses, composition of the material freezing out generally differs from that melting, so solutes are redistributed. Enrichment of the major component occurs toward one end of the rod. (Usually the end of frozen.)

In the present work, impure anthracene was subjected to zone refining. Feed first run was C.P. anthracene with a known impurity of 2.0% phenanthrene. After two passes no phenanthren was detectable in the first layer frozen. (Analysis was by ultra-violet spectrophotometry.) Although the zones melted out were …

Recovery Of Phthalic Acid, George Thomas Roberts

Theses

Crude phthalic acid from the fusion processing of alkyd resins was found to be recoverable by solvent extraction, neutralization-acidification, sublimation, distillation, esterificatton with monohydric alcohols, ion exchange or alkyd resin preparation.

The author proposes that alkyd resin preparation, based on analysis of the crude phthalic acid, is the most practical way for the alkyd resin manufacturer to recover the crude phthalic acid. No purification of the crude phthalic acid is necessary for this utilization and the resulting alkyd resin is saleable at a profit.

The Rates Of Hydrolysis Of Aryl Halides, Jack Robert Roeder

Theses

The object of this work was to determine the relative activity of the halogens, chlorine, bromine and iodine toward hydrolysis in a water-soluble aryl halide in which the halogen is activated by a nitrogroup in the orthoposition.

The order of activity was found to be C1) POI. In the case of the chlorine compound a run was also made on sodium 2-chloro-5-nitrobenzenesulfonate in which the nitro group is in a pare position with respect to the halogen.

The preparations of sodium or potassium 4-chloro-3-nitrobenzene sulfonate (I), sodium or potassium 4-bromo-3-nitrobenzene sulfonate (II), sodium or potassium 4-iodo-3-nitrobenzene sulfonate (III), and sodium …

Exchange Adsorption Of Electrolytes On Titanium Dioxide, Richard Algimantas Slepetys

Theses

During the manufacture of titanium dioxide pigments many processing steps are carried out in solutions of electrolytes. Adsorption of these electrolytes strongly affects properties of the finished pigments.

Adsorption of electrolytes Was studied on titania samples prepared by controlled neutralization of titanium tetrachloride solutions with ammonium hydroxide, and one sample of commercial sulfate process rutile titania. In analogy to zirconia--as reported by Kraus and Phillips?^22,23 titania also behaved as a weak anion exchanger in acid solutions and as a weak cation exchanger in basic solutions. Acid or base liberated was approximately equivalent to ions exchanged. On the best sample …

Continuous Chlorosulfonation Of Benzene Ii Phase Relations, Ernest Eugene Wiegleb

Theses

This work presents data for the separation of materials involved in the chlorosulfonation of benzene using carbon tetrachloride as an inert extraction solvent. Equilibrium and tie line data for the liquid ternary systems; carbon tetrachloride chlorosulfonic acid - sulfuric acid; Benzenesulfonyl chloride - carbon tetrachloride - sulfuric acid; benzenesulfonyl chloride ehiorosulfonic acid - sulfuric acid and for the quaternary system benzenesulfonyl chloride - carbon tetrachloride chlorosulfonic acid - sulfuric acid have been determined. The tie line data has been correlated by the method of Othmer and Tobias.

Data for two chlorosulfonations made under differing conditions is also given.

Thermodynamic Properties Of Monochlorobenzene, Gaetano Zaccaria

Theses

The thermodynamic properties of saturated and superheated monochlorobenzene were evaluated at ten degree temperature intervals from 0°C to 750°C and at various pressures up to 300 atmospheres.

Equations relating the specific heat, the vapor pressure, and the density with temperature, were derived from the data available in the literature. They were used together with generalized charts to evaluate the thermodynamic properties.

The values for temperature, pressure, specific volume, enthalpy, and entropy for saturated and superheated monochlorobenzene are presented in the form of tables.

An Investigation Of The Hofman Reaction As A Possible Method Of Synthesizing 3,4-Diamino Pyridine, Harry William Zbinden

Theses

This study presents an attempt to evaluate the Hofman degradation as a method of synthesizing 3,4-diamino-pyridine from isoquinolinic acid. Since the pyridine ring is known to he stable under the reaction conditions, and analogous aromatic diamides have been prepared by previous investigators, the major problem studied is the effect of hypohalites on ortho-oriented aromatic diamides.

Three methods of approaching the problem were unsuccessful in producing the desired diamine, but the last method, stepwise degradation of each group separately, may be workable with some changes.

The most significant result was the observation of an unexpected side reaction when the diamide was …

Viscosity Of A Three Component System, Acetone-Ethanol-Water, At 25°C And 30°C, Peter Fred Widmer

Theses

The viscosity in the three component system Acetone-Ethanol-Water has been determined over a range of compositions at two different temperatures, 25°C and 30°C. Compositions have been varied in increments of ten percent by weight to cover all possible combinations of the three components. The data obtained are presented on triangular coordinate graph paper with lines of constant viscosity indicated and also in tabular form.

Aryl Sulfonation In Presence Of Phosphrous Trichloride, William Calvert Tanner

Theses

With sulfuric acid as the sulfonating agent, phosphorus trichloride is demonstrated as being effective in facilitating the sulfonation of some aromatic compounds. Optimum conditions are a molar ratio of 0.5 mole of sulfuric acid: 1.0 mole of aromatic compound with 4 - 5% more phosphorus trichloride than is required to react with the available water in the system, and reaction temperatures between 50°C. and 60°C.

The aromatic compounds studied were benzene, chlorobenzene, bromobenzene, and nitrobenzene.

An Analysis Of Predetermined Time Systems, Richard Otto Schmid

Theses

This paper endeavors to compare three predetermined time systems, namely; Work-Factor, Methods-Time Measurement and Basic Motion Time-study, elemental-by-elemental, through the use of a series of detailed analyses. The following information in the form of conclusions and recommendations has been set forth from the investigation of the various comparative analyses contained herein:

1. Reasons for the variation between the elementals.

2. A chronological order of attack for further study with an eye to accomplishing the most in the shortest possible time.

3. The results of a composite analysis which utilizes the most realistic elemental definitions of the three systems. (This includes the comparison of …

   ---

   Go to article

The Use Of Perlite As An Adsorbent, John Herrick Eigler

Theses

The adsorptive properties of perlite, an expanded volcanic glass, have been studied. Several activating treatments were investigated, air oxidation it 400 degrees Centigrade appears to be the best, The adsorption of the basic dye emethylene blue yields a saturation valve of 50 milligrams per gram of perlite. The acid dye cotton blue showed no measurable adsorption. A maximum adsorption of 15 millimoles of acetic acid and one milligram of iodine were found in aqueous solution. A high value of 1.33 milligrams of iodine per gram of perlite were found in methyl alcohol solutions. The surface area of perlite appears to …

Liquid-Gas Flow In Venturi Meter And Sharp Edged Orifice, Frank John Chwalek

Theses

The results of a study of pressure drops across a 5/32 inch throat venturi meter and a 5/32 inch thin plate sharp-edged orifice for the horizontal cocurrent, flow of the air-water two-phase two-fluid system in a 3/4 inch pipe under essentially isothermal conditions, are presented. This is the first critical study of two phase flow in a Venturi meter and. in a 5/32" orifice.

Flows of water of 0.1 to 1.7 gallons per minute with air rates in range of 0.00022 lbs/sec. to 0.0092 lbs/sec. of air mixed in were studied. All flows were turbulent when judged with the conventional …

Hydrolysis Of Sodium Silicofluoride, Frank Arthur Graf

Theses

The kinetics of an apparent solubility decrease of commercial sodium fluoride encountered in a piece of equipment designed to produce saturated sodium fluoride solution was Investigated, in order to understand why a consistently saturated solution was not possible to achieve with plain tap water as solvent.

The main impurity, about 1 percent sodium silicofluoride, coats the sodium fluoride crystals, resulting in an equilibrium shift during dissolution of the salt in water; and under certain conditions results in the formation of a protective gel. Therefore, in order to produce a constant strength sodium fluoride solution, this coated impurity must be decomposed …

The Preparation Of 3,4-Diaminopyridine, Emil John Fencl

Theses

The preparation of 3,4-diamincpyridine from pyridine was investigated, but found to be of little synthetic value because of the low yield obtained on the rearrangement of 4-nitraminopyridine to 3-nitro 4-aminopyridine. In attempt to nitrate nicotinamide-N-oxide resulted in the isolation of nicotinic acid-N-oxide. Attempts to nitrate nicotinic acid-N-oxide were unsuccessful. Attempts to oxidize 3-methylpyridine-N-oxide and 4-nitro-3-methylpyridine were unsuccessful. The nitration of 3-methylpyridine-N-oxide led to the isolation of 2-nitro-5-methylpyridine, which has not previously been reported as a by-product of that reaction.

Ammonia Catalized Phenol Formaldehyde Resins, Murlin Charles Ehrgott

Theses

The literature on ammonia-catalyzed phenol-formaldehyde resins is reviewed and critical comparisons are made of the manner in which the ammonia-catalyzed resins differ from both the alkali- and acid-catalyzed resins.

Intermediate products formea during the initial stapes of the ammonia-catalyzed phenol-formaldehyde reactions, as reported in the literature, are tabulated and % N contents are calculated.

Experimental determinations of N content of resins with molar ratios of 1:1.25 phenol to formaldehyde with ammonia at 0.2, 0.5, and 1.0 moles per mole of phenol, show that at the 0.2 molar ratio of ammonia, all the N enters into the resin and remains during …

Heat Transfer Coefficients In An Agitated Vessel Using Verticle-Tube Baffles, Edward Joseph Barrasso

Theses

Data are presented to show the effect of impeller speed, impeller type, and fluid properties on the forced-convection film coefficient of heat transfer for verticle tubes in a cylindrical vessel. A generalized equation to predict the film coefficient of heat transfer on the outside of verticle tubes in an agitated vessel for both cooling and heating is also presented. This equation may be used to estimate the necessary areas of heat transfer for verticle tubes in an agitated vessel within the degree of accuracy required from most engineering calculations.

This study was the first initiated to develop an equation to …

Electrodeposition Of Cellulose And Carboxy-Methylcellulose, Charles Edward Driesens Jr.

Theses

The previous work done by Frank Cozzarelli on the eleotrodeposition of cellulose from a sodium zincate-urea-cellulose system has been verified, except that zinc was found to deposit on the cathode at all voltages and current densities within the range of the optimum conditions for deposition. The optimum conditions are: voltage - 1.10 to 1.28 volts; current density 0.13 to 1.10 amperes/square foot; electrode material - copper. Current efficiencies range from 0.80 to 5.53%.

A chelate-like complex formed from the sodium zincate and urea which couples with the cellulose has been proposed as a possible explaination of the mechanism governing the …

The Fatty Acid Alkanolamide Reaction, Julius Galender

Theses

An alkanolamide detergent can be formed by the condensation of coconut fatty acid and diethanolamine. A great many factors can influence this formation. It is shown that varying the molar ratio of amine to acid, results in a change in the fraction of acid converted. It similarly affects the molar quantities of amine converted. Molar conversion of acid or amine is dependent upon the type of atmosphere in the reaction; more acid is converted when a nitrogen sweep is employed than when it is not used. However, proportionately more amine is converted, when a nitrogen sweep is not used. When …