Digital Commons Network^™

Experimental Investigation Of Submerged, Incompressible, Turbulent, Impinging Jets, David Tzeh-Hsian Lee

Theses

Measurements concerning various flow parameters of jets impinging on a smooth lucite plate and a heated metal plate have been carried out. In particular, it is shown that the potential core length of a jet is a function of the Reynolds number and of the jet diameter. It has also been demonstrated that impinging jets behave in many important respects like free jets, except in the immediate vicinity of the target plate.

The flow behavior in the wall jet zone was investigated experimentally, and a satisfactory agreement with the results of the previous investigators was found. The maximum velocity decay …

A Rheological Equation Of State For Blood At Low Shear Rates, Anatoly Dritschilo

Theses

In this work a new rheological equation of state is presented and its application to blood is studied. The equation considered is a linear combination of Newtonian and non-Newtonian contributions to the apparent viscosity. The general form of the equation is

 T_ij =-(A + Be^{-1/C|(.5)Δi/j:Δj/i|1/2})Δij

Data from the literature were used to test the equation by generating curves of measured torque (T/L) versus applied shear rate (Ω) that would characterize the behavior of blood at all red cell concentrations and all shear rates in the Gilinson, Dauwalter and Merrill viscometer. The constants for the equation were …

Financing The Nuclear Fuel Requirements Of Public Utilities, Peter A. Lewis

Theses

A major portion of new electric generating capacity will be nuclear powered. The change to nuclear power will require large outlays of capital not required with conventional fuels to finance nuclear fuel inventories. Nuclear fuel financing requirements are unique because nuclear fuel is not consumed in the same manner as conventional fuels. Financing has not been a problem to date because nuclear fuel can be obtained only through lease from the Atomic Energy Commission. This arrangement will be terminated by June 30, 1973 and from that date on all nuclear fuel must be privately owned. Electric utilities have shown an …

The Season Of Man, Karl Schantz

Theses

None provided.

Pattern Recognition By Means Of Electric Stimuli, Melvyn Kreitzer

Theses

None provided.

Computer Specification Of Centrifugal Pump And Motor, Paul David O'Lenick

Theses

The purpose of this thesis is to develop a PORTRAIT computer program for selecting a centrifugal pump and motor driver. This is accomplished by means of generalized data which establishes the speed of the Dump and its power requirement. After selection of the pump, the motor is sized and specified. In addition to determining the pump and motor, the program also sizes the discharge and suction lines and the required control valve. The resulting solution yields the pump design data, motor, line and control valve sizes. From this data utility and relative equipment costs can be estimated.

Noise Power Ratio Testing Of Multichannel Single Sideband Communication Equipment, Per Vinther

Theses

It is shown, that Noise Power Ratio (NPR) testing of multichannel Single Sideband (SSB) transmitters should be performed loading all channels with identical white, gaussian, zero-mean noise signals in order to obtain the worst case result. A theoretical analysis of bichannel equipment under the two different input conditions: (a) statistically independent noise signals, and (b) statistically dependent noise signals; shows that the intermodulation distortion on the output of the transmitter is the same for either case. This result is extended for an arbitrary number of channels to the point of showing that the test results obtained for statistically dependent noise …

Application Of S-Parameter Techniques To Amplifier Design, Frank Sulak

Theses

1. Discussion of s parameters and their applicability to high frequency design. 2. Measurement of s parameters and evaluation of stable operating regions. 3. Synthesis of high frequency transistor circuitry with the aid of scattering parameter design equations. 4. Verification of design theory by evaluating the performance of bread-board models.

Environmental Relationships, Michael Cotsworth

Theses

None provided.

The Plasticization Of 4-Methyl-Pentene-1 (Tpx-Rt-D30) Polymer With Petroleum Jelly, Joseph P. Mccann

Theses

The properties of TPX-RT-D30 (4-methyl-pentene-1 polymer) have been changed by blending petroleum jelly with the polymer. The polymer was blended in a Brabender apparatus with up to 40% by weight petroleum jelly (P.J.) at 270°C, pressed and quenched in water. Samples were die cut for the various tests. The polymer tensile properties (ASTM-638-64T) showed both a break and yield value in all ratios as compared to only a break value for the TPX-RT polymer. Breaking strength ranged from 4000 psi for pure TPX-RT down to 1000 psi at 40% P.J., with a leveling point of 2000 psi at 15% P.J. …

Critical Interaction Constants For Binary Gas Mixtures For Use In The Redlich-Kwong Equation Of State, Warren J. Biss

Theses

In this work, critical interaction constants were used to evaluate the interaction coefficients of the Redlich - Kwong constants for bin-ary gas mixtures. From these constants, the pressure - volume - temperature behavior of the mixtures was calculated using the Redlich - Kwong equation.

The critical interaction constants, T₁₂ and P₁₂ , were evaluated for binary mixtures by solving, simultaneously, two second degree equations relating terminal slopes for critical pressure loci and the mole fractions of the components present. The feasibility of this method was tested by calculating P-V-T data for binary mixtures and comparing this with values …

Realization Of Transfer Impedances Using Distributed Rc Elements In A Common Ground Linvill Configuration, Walter Woronka

Theses

One of several synthesis procedures available for the realization of a transfer admittance is that of Linvill. This synthesis procedure employs an active element, a negative impedance converter (NIC), to shift the poles of passive immittance functions from the negative real axis into the complex plane to realize the desired transfer immittance function.

The Linvill synthesis procedure is extended to networks containing cascaded distributed RC elements and the conditions which must be satisfied to realize a transfer impedance using these distributed elements are defined.

Premix Molding Compounds : The Effect Of Processing Technique On Profitability And Product Integrity, Albert Robert Kurkowski

Theses

Premix molding compounds, presently manufactured in a double-armed blade kneader mixer, can now be prepared by a new and unique method utilizing a high speed densifier. Compounds processed in a kneader mixer, by virtue of its overlapping, shear mixing motion, are extremely susceptible to glass fiber degradation and. consequent mechanical strength reductions in moldings. Previously, as this was the only equipment, available with the capability to admix highly viscous materials, processors would formulate and design to compensate for the resultant property reductions that are encountered. Also typical of conventional kneader mixer processes is an inherent materials handling problem and mixing …

A Correlation Of Latent Heats And Densities Of Pure Organic Liquids From Known Vapor Pressure Data, Vincent J. Vasta

Theses

Employing the correlation developed by Kemme (5), which is based on a hole model for a liquid, relating vapor pressures with corresponding liquid densities and the number of carbon atoms in a molecular chain for a homologous series, correlation coefficients were established using multi-linear regression analysis on available literature data. This correlation was newly applied to several straight chain homologous series including the n-acids, formate esters and n-alkyl benzenes.

A second correlation developed by Kemme (5) relating vapor pressure, internal heat of vaporization and the number of carbon atoms for a homologous series was employed to determine correlation coefficients for …

The Optimization Of A Catalytic Methanol Reactor, Peter Wrampe

Theses

The development of a computer program which determines the minimum space time of the methanol synthesis reactants is presented. Also, the optimum temperature profile along the catalytic reactor was predicted for a desired conversion at a given operating pressure, feed composition, and catalyst effectiveness factor.

The equilibrium conversion of methanol was determined at various reaction parameters. Rates of reaction were ascertained and maximized with respect to temperature for various conversions and given reaction parameters. The results, along with those obtained when the design equation was numerically integrated, were compared to published data. Equations were established for various sets of published …

Effect Of Column Diameter On The Frequency Response Of Water Fluidized Beds, Edward C. Maiuro

Theses

The effect of column diameter on the frequency response of water fluidized beds was investigated.

Studies were made on four columns ranging from four to ten inches in diameter. Water was used to fluidize the beds which consisted of spherical glass beads .0185 inches in diameter. A trace solution of sodium chloride was sinusoidally introduced into the beds. Inlet and outlet concentrations were continuously measured by an electrical conductivity recorder. Separate frequency response tests were conducted on the inlet calmning section in an attempt to obtain the frequency response of this region alone. Results of the tests were expressed as …

The Effect Of Nitrilotriacetic Acid Upon The Biodegradability Of Linear Alkyl Benzene Sulfonate, John D. Mckenna

Theses

The effects of trisodium nitrilotriacetate (SKTA) and sodium tipolyphosphate (STPP) upon the biological degradation of linear alkyl benzene sulfonate (LAS) ware experimentally investigated by the chemical oxygen demand and methylene blue methods. It was found that when STPP was present with LAS, the degradation of the LAS was better than when alone in solution. It was also found that LAS in solution with SN TA was less degradable than LAS alone. The benzene ring of the MS appeared to degrade after most of the linear portion of the chain had already been degraded.

Evaluation Of An Alphanumeric Target As A Means Of Determining The "Resolution" Of A Photographic Reconnaissance System, Mark Underhill

Theses

This experiment relates three forms of resolution as predictors of recognition and identification of objects that could be of interest in a military photo-reconaissance situation. Of the three forms of resolution, two are based on existing types of resolution target currently used for assesment purposes and the third, being evaluated under this experiment, is based on a Block Letter (alphanumeric) target. The results and conclusions of this experiment will show that at a confidence of 90%, the Block Letter target provides a significantly better resolution value for the prediction of recognition and identification of the type of objects used in …

A Theoretical Investigation Of Color Correction Masking For The Graphic Arts, Clarence Gutteridge Jr

Theses

The theoretical functional relationship between mask density and original red, green, and blue densities has been described for a photomechanical reproduction system. A computational model simulating the reproduction system was derived and programmed on a digital computer. Spectrophotometric curves were used as originals and the needed ink amounts to reproduce these colors were specified by a set of transformation equations. The relationship obtained by regression analysis did not completely agree with conventional masking requirements. The results of this investigation are compared with the negative photographic mask technique to investigate the inadequacies of the photographic process to give adequate masking.

Liquid Vapor Equilibrium In Nucleate And Film Boiling, Walter Henry Rothaug

Theses

Liquid vapor equilibrium data were obtained for several solutions and azeotropes under both nucleate and film boiling. The data were invariant between the two boiling regimes indicating that both nucleate and film boiling are equilibrium vaporizations rather than either diffusional or bulk vaporizations. Boiling heat transfer versus temperature data were taken in nucleate and film boiling for the solutions and azeotropes and for several pure liquids. The critical heat flux for methyl alcohol-benzene solutions rose sharply at first and then more moderately with increasing alcohol concentration. The critical heat flux was pratically constant regardless of concentration in ethyl alcohol-benzene solutions. …

Coagulation In Waste Water Treatment, Garret P. Westerhoff

Theses

This paper emphasizes a practical approach to the coagulation of domestic waste water. A portion of the paper is a synopsis of current published literature on the subject. Laboratory studies on the coagulation of raw domestic waste waters were conducted to provide the basis of a practical procedure for the evaluation and design of a coagulation process. Studies included the development of a relationship between the B.O.D. and the soluble and solids portion of two waste tests. The jar test was used for the studies on the coagulation process. The final section of the paper outlines the chemical cost factors …

Reliability Considerations For Communication Satellites, Frank Polizzi

Theses

A detailed program covering all phases of reliability for a communication satellite was presented. In long mission programs such as this one, reliability is the prime consideration in assuring a successful accomplishment of the stringent goals set forth. Reliability principles and methods were incorporated in delineating each major task in the program. These principles and methods not only aided the reliability personnel in performing their duties better, but also assisted the design group, manufacturing personnel, and the testing and evaluation group in performing their jobs efficiently by being aware and knowledgeable of reliability engineering.

Various reliability disciplines were imposed, as …

The Effects Of Air-Water Two Phase Flow On The Performance Of A Centrifugal Pump, Karnig Ekizian

Theses

This study investigates the performance of a 1-inch long 4-vane open impeller centrifugal pump under two phase flow conditions. The paddle wheel pump, as branded by its manufacturer the Worthington Corporation, had a specific speed of 3400 (based on gallons per minute, feet of water and revolutions per minute) corresponding to a 7-inch impeller diameter. A 1/8-inch perforated steel pipe carried the compressed air to within four inches of the impeller eye where the air was injected into the water stream (See figures 18 and 20).

The three variable inputs were, water flow rate, pump speed and air flow rate. …

A Study Of The Properties Of The Biconical Antenna, Kurt Frank Hafner Jr.

Theses

Expressions are found for the fields produced by TM and TEM modes along a finitely conducting biconical antenna. Expressions are also found for the TM and TEM fileds along a biconical antenna having a lossy dielectric coating. It is shown that the antenna losses produce an anntenuation of the the fields along the antenna. It is found that because there is a dispersion of the fields along the biconical antenna, the attenuation produced by the losses is, in genaral, not characterized by simple exponential.

A solution is obtained for the fields of the TEM wave along a biconical antenna coated …

The Effect Of Internal Combustion Engine Operation Upon The Viscometric Properties Of Polymer Thickened Multi-Viscosity Crankcase Oils, William Charles Philcox

Theses

The effects of engine mileage upon the viscometric properties of seven different brands of multi-viscosity engine oils were examined by subjecting each brand of oil to an average of 1500 miles of service in the crankcases of different passenger cars.

Oil samples were taken every 500 miles after the oil was put in the crankcase. The control oil sample was taken from a can of oil at the time the oil was put in the engine.

The viscosity indices and kinematic viscosities at 100° F and 210° F were calculated for each sample of oil. The percent change in viscosity …

Fault Protection With A Digital Computer, George D. Rockefeller

Theses

A fundamental basis has been developed for the use of a time-shared stored-program digital computer to perform many of the electrical power-system protective-relay functions in a substation. Logic operations are given to detect a fault, locate it and initiate the opening of the appropriate circuit breakers, whether the fault is in the station or on lines radiating from the station.

The instantaneous value of the station voltages and currents are sampled at a 0.5 ms rate, converted to digital form and stored for computer main-frame use. Operating times are compatible with the 25 ms breaker trip capability of modern two-cycle …

Spectral Absorption And Related Spread Function Of A Photographic Layer, John Tuller

Theses

None provided.

Photography: A Basic Course For Art Students, Donald Dickinson

Theses

None provided.

Heat Transfer Between A Turbulent Round Jet And A Segmented Flat Plate Perpendicular To It, John Edward Chamberlain

Theses

Heat transfer between a room temperature, turbulent round jet and a segmented flat plate perpendicular to it has been investigated.

The heat transfer surface consisted of invar rings insulated from each other with silicone rubber. The source of heat was steam at atmospheric pressure condensing on the back of the heat transfer surface.

Since data were taken over a wide range of vertical distances between the nozzle and the flat surface both the potential cone and the fully developed regions of the jet were observed interacting with the heated plate.

It was determined that two modes of heat transfer occur; …

Borderline Imagery In Painting, Emery Bopp

Theses

None provided.