Digital Commons Network^™

Deposition Of Suspension In Inclined Channels Due To The Effects Of Inertia, Gravity And Image Force, I-Hsi Chu

Theses

This investigation was made to determine the effect on the deposition of particle in an inclined parallel-plate channel due to the influences of image charge, viscosity, inertia and gravity. The flow considered was lamina, imcompressible and steady. The flow patterns considered were uniform and fully developed with symmetry about the axis of the channel.

The governing equations derived for a particle were based on Newton's Second Law of motion. Since the resulting governing equations are linear second order differential equations, Runge-Kutta algorithm is used to solve the problem and graphical techniques is used to interpret the results of the numerical …

Microcomputer Controlled Instrumentation System For Studies Of Metabolic Changes In Rats, Murat Dertlioglu

Theses

The system measures the respiratory exchange in rats in a controlled experiment. An interface unit provides data, received from several measurement instruments such as gas analyzers, an electronic flowmeters, electronic thermometer and an electronic hygrometer, to the computer. The data is gathered from different chambers in a multiplexed mode.

The computer samples the chambers sequentially and prints out the results and stores them on the disk. The sampling duration of each chamber and the number of the rats to be tested can be programmed. The system can perform experiments with twelve animals, in the following arrangments, either one group of …

The Involvement Of Labor Unions In Policies Of Worker Safety And Health, Kenneth J. Dzierzawiec

Theses

American workers are exposed to many seen and unseen hazards in their working environment. As the potential hazards in the workplace became more complicated, so too did the analysis of these hazards, as well as the means of endeavoring to protect a workers safety and health.

In the period between the 1920's and the 1960's the major thrust of Union demands were in the areas of economic gain. Although there was concern for worker welfare.

The period of the late 1960's through the early 1970's brought with it a new outlook on industrial practices as compared with worker welfare and …

Computer Simulation For Studying The Performance Of Plasticating Extruders, K. S. Govindaraju

Theses

A Computer program for simulation of a single screw plasticating extruder is presented. The computer program simulates the performance of different size extruders with various screw geometries for plasticating and pumping different thermoplastic resins. The simulation yields valuable information on the performance of an extruder for a variety of operating conditions. The simulation program provides a means of separating the effect of one variable at a time on the overall performance of the extruders.

Tourist Development And Environmental Impact Of Future Airport Construction In Athens, Greece, Vasilios Michael Halkias

Theses

The present thesis is an overall study of the suitablility of the eastern region of the Attica Peninsula in Greece, for a Tourist Development. The future construction of the new International Airport of Athens within the region is a significant factor that has been taken into account for the study.

It also examines and projects the Environmental Impacts due to the Airport construction.

The description of the studied area is presented by maps and refers to the Environmental Inventory. This Inventory examines the Water Resources of the region, Topography, Land Uses, Transportation System, Air and Noise Quality, Archaeological Sites, Utilities, …

On Analysis Of Small Bore Piping Vibrations, Nitinkumar Shroff

Theses

This thesis investigates the natural frequency and vibration induced stress of small bore power plant piping. Straight piping and piping with concentrated load, such as a valve, located anywhere along the span are studied. Four different boundary conditions of fixed-free, simple-fixed, fixed-fixed and simple-simple are investigated, as any single span piping may be approximated by one of these boundary conditions.

The results otained [sic] for frequency and stress coefficients in the case of straight piping are plotted. Plots of frequency factor and stress ratio for the piping with concentrated load are also presented.

The results obtained for the natural frequencies …

The Detection Of Partial Discharges In Transformer Oil, Gerald J. Fitzpatrick

Theses

The level, meaning the number and the intensity Of partial discharges that occur in transformer oil per time period of applied pulse when a high voltage is applied can be used as a measure of the quality and remaining life of the oil. The level of partial discharges at a given applied voltage can be correlated with the degree of contamination of the oil by impurities such as water and conductive particles and can be used as an indicator of the proximity of the oil to breakdown. There are several approaches to the detection of partial discharges, e.g., acoustic measurements, …

The Dry Removal Process Of Sulphur Dioxide From Flue Gases Using Aluminum Oxide, Ching-Hwang Lu

Theses

Oxidation of sulfur dioxide to sulfur trioxide and absorption on aluminum oxide pellet as a mean of removing sulfur dioxide from flue gas was studied in a packed bed reactor at various temperatures, residence times, SO₂ inlet concentrations (ppm level), and particle sizes. Three different experiments were conducted: (i) sulfation with oxygen/ozone, (ii) sulfation with oxygen only in the presence of UV radiation ( 254 nm or 366 nm ), (iii) sulfation with oxygen only. In all the experiments substantial absorption of sulfur dioxide by alumina pellet was observed. Sulfation with oxygen/ozone give the highest absorption of SO_{2 …}

The Manhattan Project Legacy : Low Level Radioactive Waste Health Effects, An Epidemiological Study, Lisa Fetterman Voyce

Theses

An epidemiological survey was performed that included the area surrounding a former Department of Energy thorium processing and disposal facility. This facility processed monazite sands to obtain thorium under Federal Government contracts from 1941-1973.

New Jersey Department of Environmental Protection radiological surveys had shown elevated radiation levels at the Site and in the vicinity of the plant. The area was divided into sections according to distance from the site and from Sheffield Brook, which is also contaminated. Questionnaires were mailed to 400 families, with 112 responses. These represent 362 people.

Statistical analysis of the accumulated data regarding lifestyle, occupation, reproductive …

Behavior Of L-Shaped Reinforced Concrete Columns Under Combined Biaxial Bending And Compression, Amar Shah

Theses

Combined biaxial and axial compression for L-shaped reinforced concrete short columns is a common design Problem. Current code, provisions and the available design aids do not offer an insight into the determination of strength and ductility of biaxially loaded reinforced concrete column. An experimental and analytical investigation of the moment-deformation behavior of biaxially loaded L-shaped short columns were undertaken. Four 1/2 scaled specimens were tested till failure. Moment-curvature and load-deflection curves were developed from the experimental and the analytical results. The analytical results were obtained using a computer program developed by Hsu (1). From the investigation it is deduced that …

Behavior Of Tee-Shaped Reinforced Concrete Columns Subjected To Biaxial Bending And Axial Compression, Antoun Romanos Nader

Theses

The investigation deals with the effect of eccentric loading on the moment-curvature relationship of reinforced concrete tee columns.

The test program consisted of two series of tee-shaped reinforced concrete columns, loaded biaxially at constant angle from the principle axes. Their end conditions were assumed to be pinned-ended.

Loads, at constant rate, were gradually applied until failure. At each loading stage, measurements were made for the strains and deflections at the mid span section.

The experimental and theoretical results of the load- deformation and moment-curvature were compared and found that the analytical approach proposed by Hsu is applicable to irregular sections …

Prediction Of Enthalpies Of Mixing With A Unifac Model, Dinh Dang

Theses

A modified UNIFAC model is used in the correlation and prediction of enthalpies of mixing. The model requires two interaction parameters per group pair and values for 172 such pairs are presented here. Excellent prediction results are obtained with typical errors, in the temperature range of 273°K to 400°K, below 15%. For systems containing cyclic compounds, somewhat poorer results may be encountered.

Calibration Of Flame Ionization Detector For Chlorinated Hydrocarbons, Nahid Jabalameli

Theses

Relative Responses and Calibration Factors were developed for several volatile organic (mostly chlorinated) priority pollutant species in order to use one single stable compound (e.g.Benzene) for daily instrument calibration. This would replace the procedure of using a standard mixture of target compounds (25-35). This is of particular advantage because the standard mixture may not have all species stable or may show loss of some components relative to others due to wall adsorption in the standard (compressed gas) stainless steel cylinder.

The use of a single standard species was made possible by developing "accurate" relative response and calibration factors of all …

Investigations Into Rates And Mechanisms Of Mercury Depuration In The Killifish, Fundulus Heteroclitus, Joanne A. Korpanty

Theses

Metallothionein (MT) and glutathione (GSH) have been shown in mammalian research to play a role in the sequestration and depuration of mercury. The sulfhydryl groups on both these peptides have a strong affinity for mercury, MT for Hg²⁺ and GSH for CH₃Hg⁺. In this study, killifish (Fundulus heteroclitus) were force-fed one piece of squid laced with labelled mercuric nitrate to give a final food concentration of 20 ppm ²⁰³Hg²⁺ and 0.03 -0.05 µg g-1 Hg²⁺ total dose. Most of the mercury, 84.1 ± 12.1% (mean ± standard deviation), is depurated within the …

Characterization Of Tdi-Hema Homopolymer Prepared Via An Immiscible Solvent System. Synthesis And Investigation Of Oligodichloroketene, Manuel Montero

Theses

The objective of this thesis has been divided in two parts.

The first part is subdivided into two areas. First a "Universal" calibration curve for gel permeation chromatography (GPC) was construc-ted using different molecular weight standards of PMMA and MMA-HEMA co-polymers. By measuring the viscosity of the different molecular weight solutions and calculating the Vr, (retention volume), from GPC data, plots of In [ η ] Mw against Vr and In Mw against Vr are obtained. These curves can be used to obtain the molecular weight of any linear (not crosslinked) copolymer by simple measurements of viscosity and GPC data. …

Quantitative Evaluation Of Substituent Effects On Stabilization Energies Of Strained And Unsaturated Molecules, Tyler Arthur Stevenson

Theses

Thermodynamic stabilization energies are presented for a series of monosubstituted vinyl, cyclopropyl, ethynyl, and phenyl compounds. The energies are calculated using ab initio molecular orbital calculations at the 4-31G level, and also with published experimental heat of formation data. Correlation analyses are then attempted with the dual substituent parameter approach with the stabilization energies. The analyses are also attempted with a triple-parameter approach using Topsom's theoretically calculated X, F, and Ro constants. Among the findings are the facts that π-donating substituents correlate well, while π-accepting substituents do not. Indications of the relative sensitivities of hydrocarbon frameworks to substituent electrostatic and …

Performance Modeling And Simulation Of Multiple Microcomputer Systems, Moorthy Narayana Hariharan

Theses

Multiple processor systems are the logical choice for applications demanding high computing power, throughput and reliability. Moderately coupled Multiple Microprocessor systems can be applied to a variety of applications demanding high performance. The structure of Multiple Microprocessor systems is examined. Various interconnection structures are analysed for performance comparisons.

Queueing theory is a powerful tool in modeling and analysing Computer systems. Queueing models are developed for popular Multiple processor interconnection topolog es like the Shared memory, Shared bus, Star and Loop configurations.

The usefulness of Digital computer Simulation techniques in estimating the performance of Multiple processor systems is demonstrated through a …

Intelligent Computer Decision Systems, Robert J. Heath

Theses

This paper demonstrates that the concepts developed through Artificial Intelligence research are applicable to computerized information systems; and that a system of expert problem solvers and natural language interfaces exhibiting characteristics of "intelligent behavior" offer several advantages over present-day, conventional database management designs. Development of the conclusion was accomplished after an analysis and assimilation of the current literature in the field of Artificial Intelligence and participation in university symposia concerning its application to the business environment. It is concluded that incorporating the notions of learning and creativity, common sense(heuristics), and self-awareness, intelligent computer decision systems will provide managers with : …

Modification Of A Heat Transfer Program (Stan5) To Account For Surface Roughness And Its Application To Aerodynamic Icing, Parthasarathy R. Iyengar

Theses

In order to be able to predict the local ice accretion rate or the icing profile on an airfoil, it is necessary that a suitable heat transfer coefficient model be availabIe. A computer program has been developed which is capable of predicting the local heat transfer coefficient for a typical two dimensional icing surface. Because of the charecteristics of an icing surface, an existing computer program (STAN5) has been modified to include the effects of the following surface roughness surface curvature and boundary layer transition.

The computer program for the heat transfer coefficient has then been used with an existing …

Computer Analysis Of The Stefan Problem In Cryosurgery, Dong Hyuk Kim

Theses

Numerical solutions for determining the freezing front location vs time relation in cryosurgery are obtained by utilizing the heat transfer computer program TRUMP, which employs the explicit finite difference algorithm. The probe geometries of rectangular, cylindrical, and spherical shape with one dimensional heat flow are selected for study. Internal heat generation is considered in cylindrical and sphe¬rical probe geometries, and the difference between the solutions with and without heat generation is discussed. To verify the correctness of the TRUMP solution, comparisons are made in the freezing distance vs time relation with the Neumann's solution and the implicit enthalpy method for …

Decision Rules Applied To Spread Spectrum Signal Detection, Richard Jae Kim

Theses

Decision rules for detection of spread spectrum signals were investigated. For each decision rule, error and erasure probabilities were analyzed. The obtained data was used to plot PE vs Pe for constant signal-to-noise ratio (SNR). With the use of the probability of a word error curves the optimum threshold setting was found for a given SNR.

FSK (orthogonal signalling) and PSK (antipodal signalling) were considered for modulating the chips. When the PE vs Pe plots for FSK and PSK were compared, PSK performed better than FSK by a ratio of 6 dB.

Finally, analog and digital correlation of the received …

The Effects Of Feedback On Operator Performance In A Production Environment, Diane L. Knoll

Theses

The objective of this thesis and it's associated research is to analyze the positive effects of feedback in a production environment. The experimental data was collected at the Ortho Pharmaceutical Corporation in New Jersey and a subsidiary company, The J. T. Clark Company, in Illinois.

The experiments involved three types of feedback indirect feedback provided to a large group of packaging operators, direct feedback provided to a small group of temporary packaging operators in a training situation, and direct feedback provided to an entire workforce of operators performing dissimilar, but interrelated tasks.

The results of these experiments were consistent with …

Implementing A Preventive Maintenance Program In A Pharmaceutical Manufacturing Plant, Daniel J. Shatynski

Theses

The goal of Preventive Maintenance is to reduce operating costs through greater equipment availability and lower downtime costs. Its intention is also to reduce the frequency and severity of corrective maintenance. A case study of a chemical manufacturing plant in the pharmaceutical industry is reviewer and symptoms are illustrated for purposes of definition. The development and implementation of a Preventive Maintenance program for this chemical manufacturing plant is proposed.

Management Improvement Study Of The Engineering Function In A Converting Industry Company, James John Slovak

Theses

A study was made to determine if the profitability of a converting company could be improved by expanding its engineering department. Process challenges were examined along with the present engineering function to determine difficulties. A case study of capital budget projects completed in the last three years revealed that potential savings were lost due to late and incomplete projects. The conclusion is that profitability can De increased through process control improvements and more timely completion of capital projects by expanding the present engineering department.

A Systematic Program For The Management Of A Sanitation Function In The Food Industry, John Joseph Sprainitis

Theses

The sanitation of food processing and packaging facilities is a labor intensive activity. As with any labor intensive operation, effective planning and control of the manpower is necessary. The more effective tie management, the more effective and productive the manpower will be.

As the effectiveness of the management improves, the cost effectiveness of the manpower will improve.

In dealing with the manufacturing of foods, there are numerous government regulations, of which sanitation plays a key role. Misunderstanding the impact of these regulations, and either over- or under-reacting to them, can result in unnecessary costs or severe problems.

In order to …

Plate Buckling Under Biaxial Patch Loading, Herli Surjanhata

Theses

This thesis is concerned with the buckling of rectangular plate-shaped elements under biaxial compressive loading with patch loading along one pair of opposite edges. The loading along the other edges is continuous but the discontinuous loading covers different patches along opposite edges. All the applied loads are uniformly distributed. The critical buckling load of this type of plate element is an important factor in the optimal design of many types of thin-walled structures. Frequently the nature of the problem prohibits an exact or even a general form of solution, thus dictating a numerical approach.

The problem has been attacked to …

Implementation Of Dbase Ii In Inventory Management By A Small Firm, Shih-Chieh Wang

Theses

No abstract provided.

An Investigation Of Characteristics Of Blood Velocity In A Simulated Circulation System, Yung-Gang Wu

Theses

The major objective of this thesis is to find the relationship between the blood velocity and the stenosis of the vessel. Tests were performed with different degrees of stenosis at varied logitudinal positions from the testing probe in the vessel of a Z-80 microprocessor controlled artificial circulation system.

Three methods were used to detect the velocity in the vessel: continuous wave Doppler, Pulse Doppler, and a hot-film device. The first method can get the average velocity, while the latter two have the capability to find a velocity profile, and all are important indicators to the arterial occlusion phenomenon.

An analysis …

Flow In A Channel With An Abrupt Change In Area : Finite Element Method, Ching-Fu Yu

Theses

Steady flow with an incompressible non-viscous fluid in a two-dimensional channel with an abrupt change in the width of its flow passage has been studied with a finite element method and a complex potential method.

The flow problem was solved with the use of an existing finite element program, FLOW2, in terms of the velocity potential and the stream function. The general procedure of solving problem by finite element method and the user's guide of FLOW2 program are presented in this thesis.

A computer program, EXACT, has been written for the exact solution based on the complex potential method to …

A Model Of Heat Transfer By Conduction And Radiation In Fluidized Bed, Kouadio Kouame

Theses

A model of heat transfer by conduction and radiation in fluidized beds operating in the bubbling regime is proposed. The analysis of the combined conduction and radiation is one dimensional and is based on the emulsion packet model. The problem is formulated in terms of a non-linear partial differential equation which is transformed into an ordinary differential equation by using the similarity transformation. The packet emulsion phase is assumed to be a semi-infinite medium which absorbs, emits and scatters thermal radiation. Moreover, the packet emulsion phase is considered to be under optically thick condition. Radiative transfer during bubble contact is …