Digital Commons Network^™

Radiation Noise Source Modeling And Near-Field Coupling Estimation In Rf Interference, Liang Li

Masters Theses

"With increasing complexities and shrinking size of modern electronic devices, the near-field RF interference issues are becoming challenging for RF-digital mixed circuit design. Predicting the coupling from digital module to RF antennas and mitigating RF interference is important to the system performance. The ultimate goal of this study is to address the desensitization issues existing in modern electronic devices that have mixed high speed digital-RF circuits, such as cellphone and wearable devices.

In order to estimate the near-field noise coupling from digital module to RF antennas, the noise source is anticipated to be replaced by its equivalent radiation model which …

Thrust Sensing For Small Uavs, Christopher Scott Marchman

Masters Theses

"Unmanned aerial vehicles (UAVs) have become prevalent in both military and civilian applications. UAVs have many size categories from large-scale aircraft to micro air vehicles. The performance, health, and efficiency for UAVs of smaller sizes can be difficult to assess and few associated instrumentation systems have been developed. Thrust measurements on the ground can characterize systems especially when combined with simultaneous motor power measurements. This thesis demonstrates the use of strain measurements to measure the thrust produced by motor/propeller combinations for such small UAVs. A full-bridge Wheatstone circuit and electrical resistance strain gauges were used in conjunction with constant-stress cantilever …

Evaluating Completion Performance For Gas Wells In The Upper And The Lower Montney Formation, Canada, Omar Qasim Mohammed

Masters Theses

"Identifying the key drivers for success of multiple fractured horizontal wells is not straightforward, especially in unconventional reservoirs like the Montney. Al-Alwani et al. (2015) provided a statistical analysis of Montney completions based on publicly available data. They showed that for the entire well population, cumulative gas recovery per stage, declines as the number of completed stages increase. However, their statistical analysis did not differentiate between completions in the Upper/Middle/Lower Montney, and did not include perforation cluster data.

This work documents the statistical analysis of 296 cased-hole horizontal gas well completions reported in the Upper and the Lower Montney. The …

Developing An Idealistic Model To Characterize And Optimize A Photovoltaic Battery Systems, Pavani Reddy Nalladimmu

Masters Theses

"Solar energy is one of the most abundant and clean energy sources of renewable energy. Due to its unsteady nature, most photovoltaic systems require a solar storage system. Ultracapacitors have proven to be an effective solar energy storage component due to their wide range of input voltages and high power density. This research focuses on characterizing the performance of a PV/UCAP hybrid storage system to meet required household loads at various locations throughout the US as a backup energy source. A calibrated empirical model was developed to characterize system performance. A load profile was designed based on a typical 2 …

Deterministic Simulation Of Thermal Neutron Radiography And Tomography, Rajarshi Pal Chowdhury

Masters Theses

"In recent years, thermal neutron radiography and tomography have gained much attention as one of the nondestructive testing methods. However, the application of thermal neutron radiography and tomography hindered by their technical complexity, radiation shielding, and time-consuming data collection processes. Monte Carlo simulations have been developed in the past to improve the neutron imaging facility's ability. In this present work, a new deterministic simulation approach has been proposed and demonstrated to simulate neutron radiographs numerically using a ray tracing algorithm. This approach has made the simulation of neutron radiographs much faster than by previously used stochastic methods (i.e Monte Carlo …

Study Jitter Amplification Of A Passive Channel And Investigation Of S₂₁ Magnitude Extraction Methodologies Using A Pattern Generator And Oscilloscope, Xinyun Guo

Masters Theses

"Recently the clock channel jitter amplification has been observed in several publications. Currently in many high-speed I/O systems, to avoid the cost and the complex clock recovery circuit design, people use traces forwarding clock signal from transmitting IC to receiving IC. When these clock traces are long enough, the amount of attenuation will induce not only inter-symbol-interference (ISI) but also modulate with the input jitter. Eventually it will lead some type of jitter been amplified after the channel. Similarly, the high speed communication channel (data channel) will also face this issue. Since there are no studies on the jitter amplification …

Intensity Control Of Dielectric Barrier Discharge Filaments, Matthew Crawford Paliwoda

Masters Theses

"When operated in a filamentary mode, a volume dielectric barrier discharge (DBD) is known to produce patterned plasma structures. These structures are currently being explored for reconfigurable metamaterial applications. In this work the presence and intensity of a single filament, within an array of filaments, was controlled by adjusting the voltage to that filament's individual needle electrode. The current, voltage, and time-averaged normalized light intensity were measured while varying the voltage of the needle through a self-biasing resistance. For a 7.5 kV, 3.2 kHz DBD in air, the needle-controlled filament intensity varies from that of the surrounding filaments to zero …

Composite Model Representation For Computer Aided Design Of Functionally Gradient Materials, Fangquan Wang

Masters Theses

"Functionally Gradient Materials (FGMs) feature smooth transition from one material to another within a single object. FGMs modeling is considered to be one of the new challenges in Computer Aided Design (CAD) area. To overcome this challenge, this thesis presents a composite approach to model FGMs. The input in STL format can be meshed and voxelized in FGMs modeling system. The material composition in each voxel can be generated from multiple different types of control features. And LTI filters including Gaussian Filter and Average Filter are applied to blur default material features in order to generate FGMs inside models. The …

De-Embedding Method For Electrical Response Extraction Of Through-Silicon Via (Tsv) In Silicon Interposer Technology And Signal Integrity Performance Comparison With Embedded Multi-Die Interconnect Bridge (Emib) Technology, Qian Wang

Masters Theses

"Traditional two-dimensional system-in-package (2D SiP) can no longer support the scaling of size, power, bandwidth, and cost at the same rate required by Moore's Law. Three-dimensional integrated circuits (3D-ICs), 2.5D silicon interposer technology in which through silicon vias are widely used, are implemented to meet these challenges. Embedded multi-die interconnect bridge (EMIB) technology are proposed as well.

In Section 1, a novel de-embedding method is proposed for TSV characterization by using a set of simple yet efficient test patterns. Full wave models and corresponding equivalent circuits are provided to explain the electrical performance of the test patterns clearly. Furthermore, broadband …

Engine Sound Simulation And Generation In Driving Simulator, Shuang Wu

Masters Theses

"Simulating a driving environment that provides engine sound as auditory feedback to the driver is a challenging task due to the complexity of engine sound, a wide range of operating speeds, and repeated sound clicking during playback. This thesis describes a method of engine sound simulation and generation for a driving simulator. By analyzing sample sounds, spectral modeling synthesis was used to decompose the sound samples into deterministic and stochastic components. Then, the modeled deterministic and stochastic signals were employed to resynthesize the sounds. To represent engine sounds not available in the recorded database, sound interpolation was applied to two …

Effect Of Timing And Source Of Online Product Recommendations: An Eye-Tracking Study, Qing Zeng

Masters Theses

"Online retail business has become an emerging market for almost all business owners. Online recommender systems provide better services to the consumers as well as assist consumers with their decision making processes. In this study, a controlled lab experiment was conducted to assess the effect of recommendation timing (early, mid, and late) and recommendation source (expert reviews vs. consumer reviews) on e-commerce users' interest and attention. Eye-tracking data was extracted from the experiment and analyzed. The results suggest that users show more interest in recommendation based on consumer reviews than recommendation based on expert reviews. Earlier recommendations do not receive …

A Statistical Analysis Of A 4.5 Mw Solar Energy Center, Archit Patnaik

Masters Theses

"This project helps a regional utility evaluate the performance of their 4.5 MW photovoltaic plant. The performance evaluation consists of characterizing the peak and average power and energy output of the plant over varying time periods. A characterization of the output power drops, or dips, is done by performing a statistical analysis of the photovoltaic plant output data. Dips are characterized by dip frequency, depth of dip, energy loss by dip, and dip duration. The results of this study will help the utility to select appropriate voltage regulating equipment on the basis of dip characteristics, and thus, optimize the performance …

Design And Analysis Of An Axisymmetric Aerospike Supersonic Micro-Nozzle For A Refrigerant-Based Cold-Gas Propulsion System For Small Satellites, Abdalla Ali Bani

Masters Theses

"The cold-gas propulsion system being developed by M-SAT requires improvements to its original nozzle design. This study documents the research, design, and analysis of a supersonic plug nozzle concept that could be integrated to the refrigerant-based cold-gas propulsion system to possibly improve its performance. As documented in this thesis, CFD analysis showed that the outlined nozzle design method resulted in a feasible nozzle concept that has the ability to out-perform a conventional nozzle of the same area ratio. The flow-fields and thrust of the aerospike nozzle, for the full and truncated nozzles, were investigated. The purpose of this study is …

Voltage Control In A Distribution System Using Active Power Loads, Mounika Chava

Masters Theses

"High penetration of renewable energy resources such as rooftop solar photovoltaic (PV) systems is exacerbating violations of the voltage limits in power distribution networks. Existing solutions to these over-/under-voltage issues include tap-changing transformers and shunt capacitors. However, tap changers only allow voltage changes in discrete steps and shunt capacitors cannot handle over-voltage situations. To overcome these problems, this thesis proposes voltage control in a distribution system by adjusting active power loads. The proposed solution can be used for both under- and over-voltage cases at any levels of voltage adjustment. First, the active power that needs to be adjusted at selected …

An Investigation Of Plugging And Increasing Oil Recovery In Sandstone Porous Media By Micrometer-Size Particle Gel, Haifeng Ding

Masters Theses

"Micrometer-size particle gel (microgel) has been developed and successfully applied to improve conformance in mature reservoirs. However, quite few researches have been published to address on their effect on oil recovery and rock permeability modification.

This work conducted a series of core flooding experiments to investigate the injectivity, plugging efficiency and improving oil recovery potentials of a couple of microgels synthesized in our lab.

First, this work studied the impact of permeability and crosslinker concentration on PAM type microgel treatment. Results shows that microgel treatment would have a less plugging efficiency in lower permeability rocks, which could be caused by …

Characterization Of Electric Solid Propellant Pulsed Microthrusters, Matthew Scott Glascock

Masters Theses

"Electric solid propellants are an attractive option for space propulsion because they are ignited by applied electric power only. In this work, the behavior of pulsed microthruster devices utilizing such a material is investigated. These devices are similar in function and operation to the pulsed plasma thruster, which typically uses Teflon as propellant. A Faraday probe, Langmuir triple probe, residual gas analyzer, pendulum thrust stand and high speed camera are utilized as diagnostic devices. These thrusters are made in batches, of which a few devices were tested experimentally in vacuum environments. Results indicate a plume electron temperature of about 1.7 …

Impact Of Repeated Cyclic Production Scheme On Eur In Low-Permeability Reservoirs, Samarth Gupte

Masters Theses

"Productivity in low-permeability reservoirs declines quickly compared to conventional reservoirs. These tight reservoirs have very high initial oil production rates but as soon as the oil near the fractured area is recovered, the production declines rapidly making economic oil and gas production a challenge for the industry. This study investigates the impact of repeated shut-in/production cycles on the ultimate recovery of oil in such environments.

A reservoir model with multiple fractured horizontal well having 30 transverse fractures is created using CMG. Reservoir permeability is varied over the range of 0.000001 md to 10 md and shut-in/production cycles of 2-weeks, 1-month, …

Single Phase Gas Flow Response Of Fractured Horizontal And Vertical Wells To Repeated Production, Divya Kandlakunta

Masters Theses

"Historically, the conventional approach to well production has been to produce continuously, minimizing interruptions to flow insofar as possible. Yet some operators have observed improved well flow rates and ultimate recovery after a significant well shut-in periods. These production increases have not been documented. This study investigates the production impact of cyclic production/shut-in on fractured vertical and horizontal gas well performance.

A numerical reservoir model in Stimplan software was used to model production in fracture stimulated vertical and horizontal gas wells. Reservoir permeability is varied over a range of 0.0001 md to 1 md, and the shut-in period was varied …

Studies On Flocculation Of Fine Mineral Tailings Using Novel Polyacrylamide Based Polymer, Simin Khatibi

Masters Theses

"One of the important features in managing or treating sulfide fine tailings is separating solids from liquid by settling test. This thesis presents results of studied conducted on flocculation of Kaolin suspensions (a model tailings) and sulfide mineral tailings. Two polymers (PAM and Al-PAM) were tested as flocculants. The zeta potential value of slurries was measured by Nano Zetasizer device.

Al-PAM was found to be more effective for flocculation of kaolinite samples and also sulfide samples while PAM with used concentration was not. This study represents the power of flocculation as a possible solution to deal with industrial tailings"--Abstract, page …

Using Eye-Tracking To Understand User Behavior In Deception Detection System Interaction, Prashanth Kumar Lakkapragada

Masters Theses

"This research presents the analysis of data collected using eye-tracking devices on user interaction with a deception detection system. The differences between two groups of subjects, namely Innocent and Guilty, were compared, where Innocent subjects did not carry any explosive and hence, had nothing to hide in declaring objects that they were carrying whereas Guilty subjects had to lie to deceive the system. The results indicate that there is no significant difference in pupil dilation between the Innocent and Guilty subjects. However, the amount of fixations on the empty spaces of slides containing an explosive image can be used to …

Periclinal Folding In Ozark Plateau: A Record Of Local Karst Collapse Or Regional Tectonic Forces?, Chao Liu

Masters Theses

"The Ordovician Rubidoux Formation of the Ozark Plateau, Missouri is typically identified as mechanically competent sub-horizontal beds of medium grained sandstone. North of Licking, MO, the Rubidoux Formation was deformed into a series of dome-and-basin shaped buckle folds, exposed in road cuts over a distance of ~10 km. Such folds are highly unusual within the Ozark Plateau and their origin remains controversial. Three major hypotheses have been proposed based on field observations and stereographic analysis. Given the pervasive distribution of karst collapse throughout Missouri, one hypothesis to explain these folds is that the Roubidoux Formation sagged into collapsed caverns. A …

Origin Of Lacustrine Carbonate-Dominated Clinoforms In The Lower-Permian Lucaogou Low-Order Cycle, Southern Bogda Mountains, Nw China, Yiran Lu

Masters Theses

"Lacustrine carbonate clinoforms deposit can reflect ancient lake condition like paleoclimate and lake type. Complex lithofacies of a carbonate-dominated clinoform package in lower Permian Lucaogou low order cycle, Bogda Mountains, NW China, provide clues on clinoform-forming processes in a half-graben lake. The clinoform package is ~5.2 m thick, prograding from S to N for ~200 m with a maximum 15o dip angle, and spans ~4 km laterally. A clinoform consists of a lower siliciclastic-rich and an upper carbonate-rich beds, forming a clinoform cycle. Results of petrographic study of 30 thin sections suggest that the clinoform package is composed of mixed …

Construction And Validation Of Tl-Ipm Generator, Jamaluddin Mohammad

Masters Theses

"Hydrokinetic energy is one of the potential sources of energy that can be extracted and converted to electrical energy using linear generator. This work discusses about construction and validation of tubular linear internal permanent magnet (TL-IPM) generator, a kind of linear generator. The generator could produce electricity by converting linear motion generated from vortex induced vibrations induced due from a flowing fluid, such as a river. A simulation model of the generator is created using Ansoft's Maxwell software, which uses finite element analysis to perform electromagnetic analysis of the generator. Then a practical generator was built and tested. The results …

Computational Fluid Dynamics (Cfd) Simulations Of Molten Steel Flow Patterns And Particle-Wall Adhesion In Continuous Casting Of Steels, Mahdi Mohammadi-Ghaleni

Masters Theses

"In this research, the measurements of clog deposit thickness on the interior surfaces of a continuous casting nozzle were compared with Computational Fluid Dynamics (CFD) predictions of melt flow patterns and particle-wall interactions to identify the mechanisms of nozzle clogging. A hybrid turbulent approach, Detached Eddy Simulation (DES), was configured to simulate both turbulent structures and particle-wall interactions inside the nozzle accurately. For experimental measurements of nozzle clogging, a nozzle received from industry was encased in epoxy and carefully sectioned to allow measurement of the deposit thickness on the internal surfaces of the nozzle. CFD simulations of melt flow patterns …

Provenance And Depositional Environments Of Fluvial-Lacustrine Sandstones Of Lower Permian Lucaogou Low-Order Cycle, Bogda Mountains, Nw China, Xiaowei Peng

Masters Theses

"Compositional and textural maturity of sandstones may reflect provenance lithology and sediment transport distance, which are useful for paleogeographic reconstruction. 37 sandstones in six outcrop stratigraphic sections in Tarlong-Taodonggou and Zhaobishan areas in the greater Turpan-Junggar rift basin were studied to investigate the fluvial-lacustrine sandstone provenance in lower Permian Lucaogou (LCG) low-order cycle, Bogda Mountains, NW China. 400 points were counted in each thin section. All the samples are classified into lithic arenites, subarenites, wackes, and mudrocks. Three Petrofacies are defined. Petrofacies A is characterized by a high lithic content which is dominantly basaltic lithics with minor sedimentary lithics and …

Event-Sampled Direct Adaptive Neural Network Control Of Uncertain Strict-Feedback System With Application To Quadrotor Unmanned Aerial Vehicle, Nathan Szanto

Masters Theses

"Neural networks (NNs) are utilized in the backstepping approach to design a control input by approximating unknown dynamics of the strict-feedback nonlinear system with event-sampled inputs. The system state vector is assumed to be unknown and an observer is used to estimate the state vector. By using the estimated state vector and backstepping design approach, an event-sampled controller is introduced. As part of the controller design, first, input-to-state-like stability (ISS) for a continuously sampled controller that has been injected with bounded measurement errors is demonstrated and, subsequently, an event-execution control law is derived such that the measurement errors are guaranteed …

Reduction Of Emi Due To Common Mode Current Using Common Mode Filter Or Lossy Material, Qian Liu

Masters Theses

"This thesis consists of four papers. In the first paper, two new common mode filter structures were designed, fabricated, and measured. A "sandwich-type" EBG structure that resonates at the desired filter frequency is designed to suppress common mode filter on differential signals. The new filters are placed on top of the PCB as a surface-mount component, instead of being implemented within the PCB stackup. The total radiated power (TRP) of the implemented filter is investigated and discussed. RF absorbing material and traditional shielding are considered to reduce the TRP.

In the second paper and third paper, new PCB-embedded common mode …

Pim Source Identification Using Vibration Modulation Method, Sen Yang

Masters Theses

“In Section 1, passive intermodulation (PIM) is introduced and the mechanism of it is briefly explained. Then, the up-to-date PIM testing and source identification method in the industrial and academia worlds will be summarized.

The vibration modulation method for PIM source identification is proposed in Section 2. Different vibration sources were tested and compared, and the test results showed that the vibration modulation method is able to identify PIM source with good accuracy.

Section 3 outlines a special PIM source identification system built based on the vibration modulation system. The two subsystems, PIM receiver and PIM vibrator, are illustrated in …

Avon Alkaline Igneous Province, Missouri: Characterization Of Subcontinental Mantle Source And Evolution Via Chemical Analysis Of Olivine, Zachary William Freeman

Masters Theses

"This article presents the crystallization age of, and composition of olivine phenocrysts within an alnoite of, the Avon Alkaline Igneous Province (AAIP) of Ste. Genevieve County, Missouri. The AAIP is an ultramafic igneous province consisting of approx. 80 known intrusives of diverse lithology and texture. ⁴⁰Ar/³⁹ Ar geochronology indicates an emplacement age of 386 +/- 1 Ma, which establishes the AAIP as the only known Devonian-age ultramafic igneous body in the Midwestern U.S. Study of the AAIP provides a unique opportunity to characterize the Devonian-age subcontinental mantle and the processes that generated the suite of ultramafic rocks present …

Design And Fabrication Of A System For The Additive Manufacturing Of Transparent Glass, Luke John Gilbert

Masters Theses

"Despite glass' prevalence in the scientific and engineering community, very little research has been conducted attempting to additively manufacture (AM) glass. Even less research has been done on optically transparent glass. Glass’ material properties make it ineligible for most AM processes if the end result is to be transparent. Even small gas inclusions can cause large amounts of scattering. Additively manufacturing transparent glass brings the advantages found in other AM processes with the added benefit of having optical properties better than those found in polymers. Additively manufacturing glass also allows the optical properties of transparent parts to vary arbitrarily. This …