Digital Commons Network^™

Radiation Immunity In Cable Harnesses And Differential P/N Skew In Pcb, David Nozadze

Masters Theses

"We develop an efficient method to model RF immunity of multiwire cable harnesses and study differential P/N skew effects on channels, channel performance and specifically on the eye diagrams at the SerDes receiver.

External radiation can induce unwanted signals in transmission lines. For example, external radiation from an antenna induces common-mode currents on the outer surface of cable shields. This common-mode signal makes its way through the shied due to its imperfections, inducing the inner common mode. When twisted pairs inside the cable are not balanced, inner common mode is in turn converted to the differential mode, which might compromise …

Evolved Parameterized Selection For Evolutionary Algorithms, Samuel Nathan Richter

Masters Theses

"Selection functions enable Evolutionary Algorithms (EAs) to apply selection pressure to a population of individuals, by regulating the probability that an individual's genes survive, typically based on fitness. Various conventional fitness based selection functions exist, each providing a unique method of selecting individuals based on their fitness, fitness ranking within the population, and/or various other factors. However, the full space of selection algorithms is only limited by max algorithm size, and each possible selection algorithm is optimal for some EA configuration applied to a particular problem class. Therefore, improved performance is likely to be obtained by tuning an EA's selection …

A Study On End-Anchorage And Bond Behavior Of Steel-Fiber Reinforced Cementitious Matrix Composites Externally Bonded To A Concrete Substrate, Christopher Michael Moore

Masters Theses

"Fiber reinforced cementitious matrix (FRCM) composites are a strengthening material consisting of continuous fibers embedded in an inorganic matrix that have the potential to provide additional flexural and shear strength to concrete and masonry members. When used for external strengthening, however, debonding of the material is often observed due to slippage of the fiber with respect to the matrix, causing loss of composite action and a reduction in load carrying capacity. The composite utilized in this study consisted of continuous steel fibers embedded in an inorganic cementitious matrix bonded to a concrete prism. Additionally, an end-anchorage system was implemented with …

Evaluation Of Naturally Occurring And Anthropogenic Contamination In Missouri Streams, Christina Jane Sehrt

Masters Theses

"The goal of this study is to observe the values and variability of water quality parameters and benthic macroinvertebrates in watersheds with very little anthropogenic impact and to compare these values with those acquired in watersheds with more anthropogenic impact. The following five HUC 12-digit watersheds had very little anthropogenic impact and were considered "pristine": Rogers Creek, Mill Creek, Middle West Fork-Black River, Bee Fork, and Ottery Creek. Five largely urban sub-basins were also considered; these basins are: Grand Glaize Creek, Glaize Creek, Sugar Creek, Hominy Creek, and Grindstone Creek. For each watershed, both water quality parameters and benthic macroinvertebrates …

Program Management For Concurrent University Satellite Programs, Including Propellant Feed System Design Elements, Shannah Withrow-Maser

Masters Theses

"Propulsion options for CubeSats are limited but are necessary for the CubeSat industry to continue future growth. Challenges to CubeSat propulsion include volume/mass constraints, availability of sufficiently small and certified hardware, secondary payload status, and power requirements. A multi-mode (chemical and electric) thruster was developed by at the Missouri University of Science and Technology to enable CubeSat propulsion missions. Two satellite buses, a 3U and 6U, are under development to demonstrate the multi-mode thruster's capabilities. Two key challenges related to these missions are the development of the feed system to support the thruster and management of the two bus programs' …

Computational Fluid Dynamics Modeling Of Proppant Static Settling Velocity In High Viscosity Friction Reducers, Chen Yuan

Masters Theses

"In the current petroleum fracturing industry, it is necessary to understand the downhole migration and settling velocity of the proppant. If we can master this information well, it will be a great help to obtain effective propped fracture conductivity. In order to study the transport of proppants in the well, we used laboratory experiments and computer numerical simulations to compare the results to get a meaningful conclusion. We spent a lot of time building models on a powerful computer and comparing the experimental conclusions. We finally decided to use computational fluid dynamics (CFD) as the simulation platform, discrete phase method …

Impact Of Framing And Base Size Of Computer Security Risk Information On User Behavior, Xinhui Zhan

Masters Theses

"This research examines the impact of framing and base size of computer security risk information on users' risk perceptions and behavior (i.e., download intention and download decision). It also examines individual differences (i.e., demographic factors, computer security awareness, Internet structural assurance, self-efficacy, and general risk-taking tendencies) associated with users' computer security risk perceptions. This research draws on Prospect Theory, which is a theory in behavioral economics that addresses risky decision-making, to generate hypotheses related to users' decision-making in the computer security context. A 2 x 3 mixed factorial experimental design (N = 178) was conducted to assess the effect of …

Modeling Overpressure Development During Shale Rock Compaction Coupling Poroelasticity And Permeability Evolution Above 3km Depth, Wenyu Zhao

Masters Theses

"The evolution of pore pressure including overpressure during sedimentation is an important process to consider when analyzing whether high pore pressure causes rock failure. High pore pressure is caused by under-compaction due to the rapid burial of low-permeability sediments, and as a result, porosity decreases less rapidly with depth than in normally compacted sediments where porosity decreases exponentially with depth. While under-compaction related pore pressure magnitudes have been determined empirically, in most numerical modeling approaches, the pore pressure is either applied as a static magnitude or coupled to a fluid flow simulator. This study simulates the pore pressure evolution during …

Coupling Path Visualization Based On Reciprocity Theorem, Yang Zhong

Masters Theses

"A new method to visualize coupling path is proposed to help solve EMI problems. Based on the reciprocity theorem and the concept of reaction, coupling coefficient (CC) is defined to characterize coupling power density. For two-port networks, surface integral of CC can represent coupled voltage on the open-circuited port or coupled power on the loaded port. For dipole-moment based systems, surface integral of CC can represent coupled field components. The calculated CC should be a complex scalar at each point. By properly adjusting the excitation phases, the imaginary part of surface integral of CC will be zero and thus can …

Using The Ert Method To Differentiate Resistivity Anomalies Attributed To Natural And Man-Made Activities, Ibrahim Faisal Alshareef

Masters Theses

"Karst terrain is considered to be a very complex topography compared with most other geological environments. Many features can be observed such as sinkholes, air-filled cavities, losing streams, and solution widened joints. These karst features can cause subsidence and damage infrastructure such as buildings and roads thus causing economic hardship and disruption of life. The typical geological and hydrological studies are not enough to understand the karst processes.

For this reason, two geophysical methods were involved in investigating the subsurface in the study area. In this research, the electrical resistivity tomography (ERT) and multichannel analysis of surface wave (MASW) data …

Advanced Techniques For Improving Canonical Genetic Programming, Adam Tyler Harter

Masters Theses

"Genetic Programming (GP) is a type of Evolutionary Algorithm (EA) commonly employed for automated program generation and model identification. Despite this, GP, as most forms of EA's, is plagued by long evaluation times, and is thus generally reserved for highly complex problems. Two major impacting factors for the runtime are the heterogeneous evaluation time for the individuals and the choice of algorithmic primitives. The first paper in this thesis utilizes Asynchronous Parallel Evolutionary Algorithms (APEA) for reducing the runtime by eliminating the need to wait for an entire generation to be evaluated before continuing the search. APEA is applied to …

Development Of Test Methods For Characterizing Extrudability Of Cement-Based Materials For Use In 3d Printing, Jonathan Thomas Kuchem

Masters Theses

"3D printing is the process of creating three-dimensional objects using an automated additive manufacturing process. The 3D printing process has been used with materials such as metals and polymers, but application with cement based materials for the construction industry has yet to be developed. In this research, two main problems were investigated for printing cement based composite materials: extrudability and tensile reinforcement. Fiber-reinforced concrete (FRC) was studied as an internal reinforcing system to increase tensile/flexural strength. First, FRC was studied to investigate mechanical properties and use of fibers from waste tires as an environmentally friendly option. A reference mixture with …

Temporal Changes Of Nutrients Within The Lower Grand River Watershed And Selected Sites, Weston Scott Duley

Masters Theses

"This report presents the results of a study carried out in collaboration with the U.S. Geological Survey (USGS) and the Missouri Department of Natural Resources (MDNR) to estimate total nitrogen (TN) and total phosphorus (TP) at five USGS monitoring sites within Lower Grand River Watershed (LGRW) and two monitoring sites on the Missouri River. The objective of this study was to quantify temporal changes in TN and TP concentrations and compare those to best management practices (BMPs).

In this study, the approach to the analysis of long-term surface water-quality data by using Weighted Regressions on Time, Discharge and Seasons models …

Characterization Of The Surface Condition In Aa6061 Resulting From Deep Rolling As A Function Of Common Industrial Parameters, Andrew Kenneth Layer

Masters Theses

"Roller burnishing is widely used in industry to improve the surface finish and fatigue life of components. As weight reduction continues to grow in the automotive and transportation industries, deep rolling can help maintain product performance by mitigating the increase in component stresses resulting from lower weight systems. Deep rolling parameters such as tool, applied angle, feed rate, spindle speeds, and relative tool direction all affect cycle time, product performance, and appearance. The effects of common industrial parameters on the resultant surface roughness and residual stress profiles were studied in this investigation. The samples were manufactured on a CNC lathe …

The Effect Of Cell Size And Surface Roughness On The Compressive Properties Of Abs Lattice Structures Fabricated By Fused Deposition Modeling, Leah Hope Mason

Masters Theses

"Postprocessing is an important step in many manufacturing methods, but it is especially important for additive manufacturing. Researchers looking to improve the surface roughness of acrylonitrile butadiene styrene (ABS) parts fabricated by fused deposition modeling (FDM) have determined that acetone smoothing not only achieves improved surface roughness but increases compressive strength as well. This could be very beneficial to lattice structures, which are known for already having an excellent strength to weight ratio. If the compressive strength of ABS lattice structures could be improved even further using acetone smoothing, it could expand the applications for plastic lattice structures and improve …

Small Satellite Earth-To-Moon Direct Transfer Trajectories Using The Cr3bp, Garrett Levi Mcmillan

Masters Theses

"The CubeSat/small satellite field is one of the fastest growing means of space exploration, with applications continuing to expand for component development, communication, and scientific research. This thesis study focuses on establishing suitable small satellite Earth-to-Moon direct-transfer trajectories, providing a baseline understanding of their propulsive demands, determining currently available off-the-shelf propulsive technology capable of meeting these demands, as well as demonstrating the effectiveness of the Circular Restricted Three Body Problem (CR3BP) for preliminary mission design. Using the CR3BP and derived requirements from NASA's Cube Quest Challenge, five different trajectory scenarios were analyzed for their propulsive requirements. Results indicate that the …

Design And Implementation Of Applications Over Delay Tolerant Networks For Disaster And Battlefield Environment, Karthikeyan Sachidanandam

Masters Theses

"In disaster/battlefield applications, there may not be any centralized network that provides a mechanism for different nodes to connect with each other to share important data. In such cases, we can take advantage of an opportunistic network involving a substantial number of mobile devices that can communicate with each other using Bluetooth and Google Nearby Connections API(it uses Bluetooth, Bluetooth Low Energy (BLE), and Wi-Fi hotspots) when they are close to each other. These devices referred to as nodes form a Delay Tolerant Network (DTN), also known as an opportunistic network. As suggested by its name, DTN can tolerate delays …

Near-Field Scanning Based Shielding Effectiveness Extraction For Board Level Shielding Cans, Harsh Shrivastav

Masters Theses

"The conventional definition of shielding effectiveness is well suited for calculating electromagnetic shielding in the far-field. However, in the near field, shielding effectiveness calculation is not so straight forward. In radio frequency interference problems, most of the field coupling occurs in near field. Having a well-defined method to calculate near-field shielding effectiveness is important for estimating the suppression of radio frequency interference using the shield cans. In this research, a method to extract the shielding effectiveness of board level shielding cans using near field scanning is developed. Shielding effectiveness is defined by modelling the shielded noise source as equivalent dipole …

Developing A Model System Of Liquid Lubricants For Space Applications: Multiple Alkylated Cyclopentane In Alumina Enclosed Surface, Vidit Singh

Masters Theses

"Lubricants are substances used for reducing friction wear tear and energy losses between two moving bodies. For space applications, normal lubricants cannot be used as they cannot survive the harsh and demanding conditions of space. Multiple Alkylated Cyclopentanes (MACs) have been utilized as space lubricants in recent times with tremendous results. NASA uses the MACs for their missions in space, in particular 1,3,4- tri-(2-octyldodecyl) cyclopentane sold by Nye Lubricants under the name of Pennzane^TM.

In this research, an effort has been made to identify appropriate potential models for simulating Pennzane molecules and to develop MD simulation codes to …

Experimental Characterization Of Common-Mode Sources For Prediction Of System Level Common-Mode Current On Cable Harnesses, Sameer Sudha Arun Walunj

Masters Theses

"Common-mode current on cable harnesses is often the primary source of radiated emissions below several hundred megahertz. It is difficult, however, to estimate common-mode currents that will occur in a system from component level tests because the common-mode impedances are different in the system. Research presents two methods for using simple component level tests to estimate equivalent common-mode source voltages and source impedances responsible for generating common-mode current. Key to these methods is assuming the harness can be represented with two transmission lines, one terminated with a short and one with an open. Equivalent sources are predicted for those circuits …

Multiphysics Prediction Model Of Microwave Curing For Thick Polymer Composites, Siva Dasari

Masters Theses

"Microwave curing technologies have many advantages over the traditional thermal curing methods for the manufacturing of fiber reinforced polymers, especially the processing speed and energy efficiency. Energy can be instantaneously transferred through applied electromagnetic fields and heat is generated based on dipolar rotational interactions. Microwave curing processes have been used for glass fiber composites but there are significant challenges associated with microwave curing of carbon fiber composites. Efficient heating may be difficult due to high dielectric loss associated with carbon fibers. Laminate quality will be highly dependent on the uniformity of the electromagnetic field in the material. In this work, …

Abrasion Resistant Concrete Mix Design For Cold Climates, Diane Mariah Murph

Masters Theses

“Studded tire usage in Alaska contributes to rutting damage on pavements resulting in high maintenance costs and safety issues. In this study, binary, ternary, and quaternary highly-abrasion resistant concrete mix designs using supplementary cementitious materials (SCMs) were developed. The properties of fresh concrete and mechanical, and durability properties of hardened concrete for these mix designs were then tested to determine an optimum highly-abrasion resistant concrete mixture which could be placed in cold climates to reduce rutting damage. SCMs used included silica fume, ground granulated blast furnace slag, and type F fly ash. Tests including workability, air content, drying shrinkage, compressive …

Methane Dry Reforming Reaction On Cr, V, In, And Ga Supported Sapo-34 Zeolite, Ehigiator Festus Ojo

Masters Theses

”The CO₂ reforming of methane is a significant research area in mitigating and transforming two greenhouse gases for the production of syngas. The reaction has been investigated for four different promoted catalysts to determine their reactant's conversion, product’s selectivity, and their respective syngas ratios.

The catalytic test was investigated under atmospheric conditions at 600⁰C for 6.5h with a WHSV of 4800 ml g^-1 h^-1. The conversion and selectivity of catalysts 9Al 1V-inc SAPO-34, 9Al 1Cr-inc SAPO-34, 9Al 1Ga-inc SAPO-34, and 9Al 1In-inc SAPO-34 were analyzed. The CH₄ conversion for the different catalysts are, 9Al 1Cr-inc …

Unmanned Aerial And Traversing Vehicle -- A Mobile Platform For Bridge Inspections, Clayton A. Fritsche

Masters Theses

“Unmanned aerial vehicles (UAVs), also known as drones, have been rapidly growing in popularity since their creation. This study aimed to create a robotic platform used to assist in the inspection process of the nation’s aging and deteriorating bridges. To this end, a multimodal inspection robot that utilized both flying and driving technologies, was designed, analyzed, and tested for aerial, traversing, and their transitional operability. The design, herein referred to as the “BridgeBot”, was evaluated both computationally and experimentally. A finite element model of the BridgeBot was established and analyzed under static loading scenarios to help determine stress distributions and …

Development Of Castrip Dual Phase Steel, Brenton Allen Hrebec

Masters Theses

“Thermomechanical processing necessary to produce DP 980 steel using CASTRIP hot band was investigated. The resultant steel has an ultimate tensile strength of 1038 MPa, yield strength of 744 MPa, and total elongation of 8.6%. These mechanical properties were achieved by batch annealing the hot band at 649°C for 48 hours and cold rolling to a 20% reduction. The steel was continuously annealed to simulate a galvanization cycle with an intercritical temperature of 810°C. The possibility of improving the texture of the steel by warm rolling under dynamic strain aging conditions was investigated. Dynamic strain aging in the CASTRIP hot …

Performance Of One-Part And Two-Part Class C Fly Ash-Based Alkali Activated Mortars, Cedric Chani Kashosi

Masters Theses

“Seeking an eco-friendly concrete, researchers have conducted studies to fully replace ordinary Portland cement (OPC) with fly ash (FA) producing alkali-activated concrete (AAC). Results showed better performance of AAC in terms of high early compressive strength, and durability compared to conventional concrete. However, much is still unknown about the behavior of AAC. From the type of materials used, the curing procedure, and long-term strength development of these binders; a thorough investigation is needed in order to fill the existing gap from previous studies and thus make a step forward to the safely use of AAC in the construction industry. The …

Feasibility Study For Sustainable Controlled Low-Strength Material (Clsm) Incorporating Off-Specification Fly Ash And Bottom Ash, Alexis K. Vandomelen

Masters Theses

“Controlled low-strength material (CLSM) is a self-consolidating cementitious material used in applications requiring high flowability and low strength. The primary components of this material, being cement and sand, however, negatively impact the environment. Cement is a large contributor to CO2 emissions, and the vast depletion of sand causes physical and political issues. Furthermore, over 100 million short tons of coal combustion products (CCP), including fly ash and bottom ash, are created annually in the United States, while nearly half of all CCP remain unused. No off-specification fly ash has been implemented in CLSM. This study uses coal ashes sourced from …

Laser Machining Countersinks In Carbon Fiber Reinforced Polymer, Leon James Neely Hill

Masters Theses

“Laser machining countersinks with a frequency doubled Q-switched diode pumped Nd:YAG laser is demonstrated. Tests were conducted in 0.100" thick IM7 prepreg CFRP with [0,90]3S orientation. The HAZ is minimized to avoid stress concentrations in the epoxy matrix. A chamber and filtration system was designed and built to contain the byproducts produced in the machining process. The variables investigated are the number of repetitions in the offset path, the plunge rate, and the line energy. The research was performed over one baseline study, one parameter space exercise, two full factorial experiments, and one repeatability study. Assessment was done under an …

Inclusion Engineering In Femnal Steels, Rairu Vaz Penna

Masters Theses

"Low density high Mn and Al steels, or FeMnAl steels, show great promise for military vehicles and automotive applications in which high strength and toughness is a requirement. However, these steels are subject to processing challenges including development of oxide and nitride inclusions during melting and casting as well as a large as-cast grain size and heavy interdendritic segregation. This can lead to non-uniform heat treatment response and cracking during subsequent hot rolling. Adding up to 10%Al lowers the density of these steels by as much as 15%, unfortunately, this also results in large amounts of hard and faceted AlN …

Exploration For Alteration Halos Around The Ag-W Deposits In Southeastern Missouri, Usa, Daniel Joseph Warbritton

Masters Theses

"The St. Francois Mountains in SE Missouri are an extensive terrane of granitic ring complexes and associated rhyolites. They were an important source of Ag, W, and Sn and mined intermittently from the 1800s until the 1950s. The Ag-W ores occur in the Silvermine Granite and rhyolite roof rocks. The deposits are classified as a xenothermal ore system with mineralization occurring in quartz veins and surrounding greisen (up to 2.5 m). Exploration for hydrothermal ore deposits often focuses on the identification of alteration halos in the surrounding host rocks. In the vast majority of xenothermal ore deposits, such as in …