Digital Commons Network^™

Interrelationship Of Transverse Anchorage And Adhesive Bond In Welded Wire Reinforcement, Alan Arthur Becker

Masters Theses

"...Welded Wire Reinforcement Fabric has been applied only to certain "light types" of reinforced concrete construction. It has not as yet been applied as main tension reinforcement for most concrete structures, mainly due to the fact that a thorough investigation of the potentialities and possibilities of welded wire fabric has not as yet been conducted. It is expected that the data collected in this investigation coupled with data collected in similar investigations performed at the Missouri School of Mines and Metallurgy will furnish the basis for a structural and economic comparison between welded wire fabric and ordinary reinforcing bars. The …

Aerodynamic Research For An Improved Rotor Control System On Helicopters, Delmar Wallace Breuer

Masters Theses

"Since the author has always been interested in Aeronautical Engineering, and in particular, rotary-winged-aircraft, the problem of research for aerodynamic improvement of rotary-wing control systems was chosen. This problem was suggested by the Army Aircorps Officials of Wright-Patterson Field of Dayton, Ohio as being a valuable and practical problem for the government. It is also valuable and practical for the author since it follows his general course of undergraduate study and since it fits closely into the field for which he is preparing himself...The requirement with which the author is most concerned is the design system for the producing of …

A Graphic Method For Determining Pressure Losses Due To Air Friction In Mine Airways, Robert F. Bruzewski

Masters Theses

"One of the most important factors that influence the selection of a fan or blower for circulating a desired quantity of air through mine workings is the total pressure that is required to overcome the resistance of the airways. Ordinarily, the major portion of this resistance is that caused by friction of the moving air on the surface of the airways. The pressure that is required to overcome this frictional resistance is calculated by means of the friction formula"--Introduction, page 1.

Analytical Investigation Of Thin And Moderately Thick-Walled Tubing Under Peripheral And Biaxial Loading, Frank Joseph Cizek

Masters Theses

"The problem then, resolves itself into a study of the behavior of thin-walled and moderately thick-walled cylinders under the effects of an external fluid pressure acting alone, or the effects of an external fluid pressure acting simultaneously with an axial loading. In this thesis a theoretical or analytical approach will be used. Some application and reference will be made to oil-well casings in particular, but the solutions will not be restricted to oil-well casing alone. it must be recognized that the tubing problem involves the problem of unstability before the proportional limit of the metal is exceeded and a similar …

An Investigation Of The Weavability Of Wire With Observations On The Defects Of Wire And Wire Cloth, Walston Chubb

Masters Theses

"In the course of this year's work under the auspices of the Ludlow-Saylor research fellowship many problems of interest to the wire weaving industry have been investigated. Some of these problems have no academic novelty; others were not completed and have been laid aside for future investigations. The major problem for investigation this year was to discover a method by which the weavability of wire might be evaluated. A second problem for investigation was to discover the causes of some of the defects of wire and wire cloth. In addition to presenting the results of these investigations, this thesis represents …

The Barite Industry In The United States, James Byron Chaney

Masters Theses

"Within the past few years, barite has become one of the most important non-metallic substance mined in the United States, as expressed by the large increase in production since 1943. The purpose of this treatise is to combine in a single volume important information concerning the geographical distribution, geology, mining methods, milling or beneficiation methods, production and utilization of barite in the United States. A large number of references has been used in preparing this treatment. The information has, as far as possible, been brought up-to-date. It is thought by the writer that the paper will present to the reader …

Further Studies - Heat Transfer Coefficients For Liquids In Forced Convection Normal To Banks Of Staggered Tubes, Terrell C. Claunch

Masters Theses

"The problem for these experiments may be divided into two sections. The first section of the problem consists of setting up procedure for duplicating data. The second section is that of studying and explaining characteristics of the resulting curves. Correlation of the data obtained will be necessary in order to obtain the curves. In order that the first section of the problem could be solved it was necessary to establish a standard of cleanliness for the apparatus used. Establishment of procedures for the operations and cleaning of the apparatus was necessary. Before Kenneth E. Rudert began his design and construction …

Effect Of Transition Elements On The Transmittance Of B₂O₃ Glasses, Chandubhai Gordhanbhai Amin

Masters Theses

"For many years, boric oxide has been used extensively as a minor constituents in silicate glasses, because of its beneficial influence on their physical properties as well as on glass melting processes; but when used without silica or in too large proportion, the resulting glasses lack chemical durability...Because of its detrimental effect as a major constituent in silicate glasses or in borate glasses, very little work has been done on borate glasses, especially on colored borate glasses...The purpose of this investigation is to find out the effect of the transition elements on the transmission curves of the colored borate glasses"--Introduction, …

Preparation Of Copper Single Crystals By Means Of Powder Metallurgy Methods, Wei-Kung Chang

Masters Theses

"Since different mechanical properties of metals result from different grain size became known, the metallurgists have been interested in finding out the true nature of the grain boundaries. Consequently, several different theories concerning the mechanism of recrystallization, grain growth, and the structure of metals were advanced and studied. These threw much light on the difference of properties between polycrystalline metals and single crystals of the same metals. The single crystals of metals were studied because they enabled the investigator to determine the important points of metallic behavior. The first work on single crystals was rather obscure and limited to isolated, …

A Correlation Of Formulas For The Flow Of Fluids In Pipes, John Gorman Duba

Masters Theses

"At present there exist two quite distinct fields in fluid flow in pipes, the one in water supply and the other in the petroleum industry. It is the purpose of this paper to discuss the various pipeline flow formulas as used in both fields and to correlate the exponential type formula which is much used in practice with the Nikuradse curves obtained in the laboratory"--A Brief Historical Review, page 5.

Evaluation Of Quenching Media Using The End-Quench Hardenability Test, Subodh C. Das Gupta

Masters Theses

"The purpose of the thesis was to evaluate the quenching speed of different quenching media by studying their behaviour in relation to hardenabilities of steels, using the standard A.S.T.M. End-quench Test. At the outset an understanding of the term "Hardenability", so extensively used in industrial heat-treatment, is necessary, The property of a steel, of hardening on quenching to various depths beneath the surface is referred to as the 'Hardenability". It may simply be called the "susceptibility to hardening". Hardenability should be distinguished from the "Hardening capacity", which represents the magnitude of the hardness achieved. The chief factors which affect the …

The Theory Of Limit Design As Applied To The Design Of A Continuous Beam Over Three Supports, Robert F. Davidson

Masters Theses

"The theory of Limit Design is the application of the theory of Plasticity to the estimation of the actual carrying capacity of a structure. In this theory, as it is applied to statistically indeterminate structures, the areas of most unfavorable stress are allowed to be stressed beyond the yield point and into the plastic range of stress. It was formerly held that, by assuming elastic behavior, all questions of strength of materials that concern the Structural Engineer were capable of solution. However, it is now becoming recognized, from actual measurements of deformations of structures and from tests carried to near …

An Investigation Of The Production Of Multicarbide Of Tungsten And Titanium From Wo₃ - Tih₂ - C Mixtures, Chi-Mei Hsiao

Masters Theses

"The purpose of this research was to investigate the possibility of producing the multicarbides of tungsten and titanium from a tungsten oxide-titanium hydride-carbon mixture. It appears to be worthwhile to carry out the reduction, carburization, and pre-alloying in one process, i.e. reducing tungsten oxide with the dissociated hydrogen from titanium hydride and the added carbon; then carburizing the reduced tungsten metal and dissociated titanium metal; at last, pre-alloying the mixture of TiC and WC. The replacement of titanium hydride with titanium oxide seems to be more direct, simple, and economical process; but the difficulty in the reduction of titanium oxide …

Reduction Of Zinc Sulphide In A Vacuum, Tien-Shih Liu

Masters Theses

"The successful large scale commercial application of high vacuum for high temperature metallurgical operations is a comparatively new development. The use of Pidgeon and the carbothermic processes for the production of magnesium during the war forced a perfection of both equipments and techniques for high vacuum operations. This opens broadly the way for a great expansion of vacuum metallurgy. Vacuum operation is thus no more a laboratory method - it is a kind of industrial practice. Many metallurgical operations, which cannot be carried out by ordinary processes, are made feasible when conducted in a reduced pressure. typical examples are the …

Design Of A Barge-Platform Marine Drilling Rig, Ely Schwartz

Masters Theses

"ln the quest for oil in the Gulf of Mexico, princi­pally off the coasts of Texas and Louisiana, unique types of drilling rigs able to cope with environmental conditions have been developed in the last several years. This development is highly specialized and has led to methods of operation revolutionary to the oil industry and is without precedent….

In designing a drilling platform there are three cardinal aims (1) low cost installation and operation, (2) ease of operation, (3) providing safe working condi­tions.

The initial problem is to extend the shore-based fabrication and reduce the offshore construction, foul weather delays, …

A Proposed Program For The Veterans’ Institute At Dowagiac, Michigan, Harold E. Telfer

Masters Theses

Chapter I

Introduction

The close of World War II and the return to civilian life of its large number of young men and women veterans has been a period of rapid adjustments. A large number of these adjustments have been facilitated, or at least affected, by the legislative provisions of the national government. These provisions, in turn, have been affected by the applications made of them by local communities and their agencies. One example of the local application of the aims of the veterans' benefit laws is the Veterans' Institute jointly sponsored in Dowagiac, Michigan, by the Cass Country Veterans' …

An Investigation Of The Amount And Kinds Of Material Pertaining To Safety Education To Be Found In Social Studies Textbooks, Dorothy D. Osborn

Masters Theses

Chapter I

Introduction

The Problem

In spite of the fact that safety education is acquiring a definitive place in elementary school curricula, there are still many secondary school educators who are indifferent to the need of including work in safety in the already crowded school program. However, our modern mode of living with its increased tempo and its concentration of population has intensified daily hazards to such an extent that the school must consider education for safety as part of its program. Time, effort, and money spent on education of children whose lives are to be taken in adolescence by …

The Effects Of Moisture In Grog Upon Dry Pressed Mixes Containing Grog, Charles L. Mckinnis

Masters Theses

"It has been found that the aging of clay-grog-water mixes before pressing proves to be quite beneficial. The purpose of the aging period is to allow the added water to disseminate throughout the mixture of clay (plastic) and grog (non-plastic) in an effort to bring about the best bonding action possible. The clay-grog-water mixture, if not aged, is of a sticky consistency; while, if the same mixture is aged for twenty-four (24) hours, it is readily workable. This process of aging has long been recognized as a "must" in the Ceramic Industry in obtaining mixtures of ideal workability"--Introduction, page 2.

Analysis Of Simultaneous Faults By The Method Of Symmetrical Components, Robert Marshall Montgomery

Masters Theses

"The object of this thesis is to present a method for the analytic determination of fault currents and voltages of a symmetrical three-phase system that is subjected to three simultaneous faults. The fault analysis is to be effected by the method of symmetrical components...Though relatively infrequent, simultaneous faults are important because relay systems, operating satisfactorily for single faults, may fail to isolate simultaneous faults. Therefore, it seems worthwhile to have in convenient form a method for calculating short-circuit currents and voltages caused by faults occurring at the same time at three separate and distinct points of a system. It is …

A Comprehensive Traffic Survey For The City Of Rolla, Phelps County, Missouri, Leon Hershkowitz

Masters Theses

"The ultimate aim of this comprehensive traffic survey for the city of Rolla, Phelps County, Missouri, is to furnish a guide or pattern together with the necessary forms, maps and charts, that can be followed and reproduced by any city having a population of less than 10,000 in a study to determine its particular traffic problems. This survey should serve as a guide in determining what corrective action can be taken in connection with the following: (1) The improvement of location of state highway trunk [sic] routes, by-pass routes, auxiliary routes, and county roads in the city's immediate area. (2) …

The Influence Of Grade Strength On The Efficiency Of Gelatin Dynamite, Kenneth George Ackermann

Masters Theses

"This study of the relative effectiveness of different grade-strengths of Special Gelatin dynamite in dolomitic limestone was conducted at the Experimental Mine of the Missouri School of Mines and Metallurgy, Rolla, Missouri"--Introduction, page 1.

A Study Of The Separation Of Wolframite From Tin-Oxide, Chih-Wen Ying

Masters Theses

"A number of mines in china, Bolivia, England, and other countries contain both tin-oxide and wolframite. Owing to the fact that the specific gravity of tin-oxide and wolframite is so nearly the same, considerable difficulty is experienced in making a gravity separation, and all attempts to do so by wet or dry concentration have given very poor results. The perfection of magnetic separators has done much to mitigate this difficulty, so that now complex ores of this nature can be treated in a satisfactory manner. The mixed concentrate from the tables or other concentrators, after being roasted to expel sulfur …

A Comparative Study Of Some Rock Drill Bits, Paul Louis Terrasson

Masters Theses

"This paper describes a comparative study which was made of the wear and efficiency of different types of rock-drill bits when used under various drilling conditions...The four types of experiments which were carried out had the following purposes: 1. Determine the influence of the size of the bit. 2. Determine the influence of the design of the bit. 3. Determine the influence of the type of hammer. 4. Compare the performances of steel and tungsten carbide bits in limestone and in granite"--Introduction, page 1.

A Test Method For Measuring The Flow In Refractory Materials At High Temperatures, Christen Knudsen

Masters Theses

"One of the most important properties of refractory materials is the ability to resist stress which may either be directly applied or originate in the material. The factors which govern the resistance to stress include the modulus of elasticity, the ultimate strength under different types of stress, and the "flow" characteristics which become of importance when the material is stressed at the temperature at which plasticity is developed. Systematic determinations of the mechanical properties such as modulus of elasticity and ultimate or breaking stress is rather difficult or more or less impossible to carry out at the temperature at which …

The Determination Of The Surface Tension Of Benzyl Ether, Sze-Kwei Min

Masters Theses

"The accurate determination of surface tension is of importance in the investigation of theories of surface structure, the structure of liquids, molecular cohesion, in the study of colloids, especially in physiological work, and in various lines of technical chemistry. The two methods most commonly used for determining surface tension are the capillary rise method and the drop weight method. The theory of the former is simple, but its technique is difficult. Its use in some cases is the cause of errors as high as 30%, due to its inapplicability to certain classes of substance, and is much more sensitive to …

Synthesis Involving Waste Carbon Dioxide, Glenn Eldon Brand

Masters Theses

"Many industries, ranging from power plants to breweries, produce large quantities of carbon dioxide as a by-product. The burning of limestone with natural gas produces a relatively clean gas in which the carbon dioxide content may exceed 40 per cent. It is with this type gas that the present thesis will be concerned. In this process the burning of the limestone is accomplished by using natural gas as a fuel, burning usually under a pressure of about two pounds, and obtaining carbon dioxide from the combustion of the gas and the decomposition of the limestone. Such a plant producing 70 …

The Effect Of Spontaneous Crystallization Of Some Inorganic Compounds At The Critical Temperature Of Their Solvents, John William Buttrey

Masters Theses

"For many years the phenomena which occur at the critical temperature of liquids have been investigated. And since 1912, when Laue and other discovered that a beam of x-rays could be made to yield a diffraction pattern by passing it through a crystal, scientists have been attempting to change the x-ray pattern for various crystals by somehow changing the arrangement of the atoms in the crystal lattice. Harvalik has already shown that crystallization occurs when a solvent reaches the critical point and his work indicates that under these conditions of crystallization there is a change in the crystal pattern. The …

Geology Of The Berryman Area, Washington County, Missouri, Jack Alexander James

Masters Theses

"Purpose and scope - The are discussed in this thesis was selected because of recent exploration for lead within this region and because of the need for more detailed information of the structure and geologic history of the area. The work constitutes part of a program of geologic mapping by the Missouri Geological Survey and Water Resources to complete the mapping of a strip of quadrangles extending across the Ozark Uplift from Rolla eastward to the Mississippi River"--Introduction, page 1.

The Application Of The Membrane Analogy To The Solution Of Heat Conduction Problems, Lloyd Hines Wilson

Masters Theses

"The purpose of this investigation is to determine the feasibility of applying the membrane analogy to the solution of two-dimensional heat conduction problems. This investigation will deal only with heat conduction in the steady state through homogeneous media"--Preface, page iii.

The Mechanical Anchorage Value Of The Transverse Wires In Welded Wire Reinforcement Fabric, Ernst August Weinel

Masters Theses

"The tests reported in this paper were performed in an effort to secure data concerning characteristic properties of Welded Wire Reinforcement Fabric. This fabric has been used, up to the present time, primarily for temperature reinforcement. Limited attention has been focused on its potentialities for use as main tension reinforcing steel, particularly concrete highway slabs and floor slab reinforcement for buildings. The manufacturers of the Welded Wire Reinforcement Fabric believe their product can be used to better advantage as main tension reinforcement in reinforced concrete structures both from an economic and structural viewpoint, than structural steel reinforcing bars"--Object of Research, …