Digital Commons Network^™

Computerized Work Measurement System, Vrajesh Shah

Theses

This thesis is concerned with the application of computerized work measurement to improve productivity and efficiency of production workers. In doing so, the techniques of MOST (Maynard Operation Sequence Technique) is studied to determine its appropriateness for industrial use. The advantages and disadvantages of the system are studied as to its value to large and small industries.

Development Of Dynamic Analysis Program Mini-Dymac, Shang-Rou Shien

Theses

The computer program DYMAC developed by B. Paul automatically generates and numerically integrates the equations of motion of closed loop multi-body mechanical systems. The theory behind this program is Larange's form of d'Alembert's principle. However, it is not an easy task for the beginners to understand this program completely. If there is a simplified version of the program, it will be of great help for those people to understand the essential organization of the program.

Using the same theory of DYMAC, computer program MINI-DYMAC is developed in this thesis and hoped to serve as an educational version of DYMAC. For …

Investigation Into The Feasibility Of Burning Hazardous Waste In Utility Boilers, Reuben Steinberg

Theses

Disposal of hazardous waste is of major concern in recent years in this country. Declining availability of landfills together with more stringent State and Federal regulations has necessitated the need to consider alternative means of hazardous waste disposal. It was suggested that burning hazardous wastes in presently operating utility boilers might be beneficial to the utilities and offer a solution to this social problem.

This thesis investigates the feasibility of this alternative given the technical, economic and regulatory considerations involved and discusses the findings of adopting this technology for hazardous waste disposal.

Based on the results of this study it …

Digital Signal Processing On Tms32010 Evaluation Module And Analog Interface Board, Jiming Sun

Theses

The TMS32010 Evaluation Module (EVM) and Analog Interface Board (AIB) have been used to implement a digital signal processing system. This new system will be the hardware basis for research and development in the DSP field at NJIT in the future. This thesis will serve as a user's guide and overall technical manual for the system.

TMS32010 Assembler, Linker and Simulator in VAX-11 are used to develop the system software, then we can down load the object codes to the EVM through the MODEM in order to test them. By using the A/D and D/A converter as input and output …

Graphic Display Of Robot Kinematics, Ramamurthy Vishwanathan

Theses

This thesis uses the HOUIE.BYLI graphics software package to simulate the kinematics of a six degree of freedom, MAKER I robot. The coordinate frames for the various links of the robot were established. The kinematic equations for the manipulator were developed snd solved using the techniques of inverse geometric transformations and transformations of objects in 3D space. A program was also developed to calculate the joint variables of the manipulator given any point on, and the orientation of, an object. These variable values are used to direct the robot end effector to the given point. This can be seen in …

Similitude Analysis Of Model Experiments Of Piles Driven To Rock, George Nicou Georghoudes

Theses

This thesis investigates the similitude requirements for the Dynamic Pile Driving Apparatus in the New Jersey Institute of Technology Laboratory. The apparatus is being used to perform model tests to study bearing stratum fracturing caused by driving pile groups to weak rock.

Two approaches were used to establish similitude between the model and actual field conditions. The first approach utilizes dimensional analysis to develop a relationship between the energy delivered to the rock mass by the pile and the unit length. The second approach proposes a procedure to establish an empirical relationship between the threshold energy to fracture the rock …

On Natural Frequency Of The Stiffened Hvac Ducts, Jin-Lian Ha

Theses

This thesis employs ANSYS program to calculate the natural frequency of a stiffened HVAC duct and to investigate the affect of these stiffeners to the values of the natural frequency.

Investigation through this thesis shows that increases in the number of transverse stiffeners mould increase the natural frequency of the HVAC duct and the installation of the axial stiffener mould also increase the duct natural frequency.

Electrochemical Reduction Of Quaternary Ammonium Salts, Rudolph K. Kapichak

Theses

The electrochemical reduction of two highly hindered quaternary ammonium salts was attempted. The reductions were performed in hexamethylphosphoramide at a controlled potential using platinum electrodes. It was anticipated that these reductions would provide a route to the formation of anti-Bredt bridgehead olefins. This work is an extension of the work of Dubois, Monvernay and Lacaze who electrochemically reduced quaternary ammonium salts such as trimethyl-t-butylammonium iodide (XX).

Trimethy1-2,4,4-trimethy1-2-pentylammonium iodide (XXIII) was reduced to form 2,4,4-trimethyl-l-pentene (XXVI) and 2,2,4-trimethylpentane (XXV). The yields of the two runs of this reduction were 10% and 20% and in the first run of the reduction 75% …

Optimization Of Reactive Ionized Cluster Beam (R-Icb) Technique For Deposition Of Gan Films, Veronica S. Kyriacou

Theses

The deposition of GaN film onto glass substrate, using the Reactive - Ionized Cluster Beam deposition technique was studied. The creation of clusters is dictated by various parameters such as the vacuum pressure inside and outside the crucible, the crucible temperature, and the nozzle diameter of the crucible. Optimization of these parameters was experimentally studied, and deposition of gallium films on glass substrates was tried as a first step.

The direct heating method was used at first to get the 1100¬1300°C crucible temperature which was required for the creation of gallium clusters. Although different tungsten wire diameters and different number …

The Gpib User's Manual For Hx-40, Ding-Tang Li

Theses

A completed RS-232 to GPIB interfacing system has been built for HX-40 to master the GPIB oriented machine through its serial port. GPIB commands and data can be transfered between HX-40 and the slave station, which is a HP 3582A spectrum analyzer in this project. The data acquisition from serial to GPIB is done by a well-made GPNET mode 10 interfacing board in a transmitting rate of 9600 baud rate. GPNET exchanges data and commands with HX-40 through a RS-232 port, and passes them to the slave station through a GPIB port which is coordinated by GPIB protocol. A software …

Microcomputer-Based System For The Measurement Of Facial Swelling, Michael Guy Demuth

Theses

The measurement of facial swelling after oral surgery can indicate the effect of anti-inflammatory drugs. A mechanical device was interfaced to a microcomputer to allow faster calculation of swelling. The mechanical system first established X and Y coordinates on the face. A feeler arm traced out the facial contours and two linear variable differential transformers (LVDTs) related X and Y displacements to voltages which were fed into a microcomputer via an A/D converter. Three BASIC programs were written which facilitated the analysis of patient swelling. MEASUREMENT stored the X-Y voltages from the LVDTs in a patient disk file. CALCULATION filtered …

Use Of Clay As A Landfill Liner, Mayur B. Desai

Theses

The purpose of this thesis is to study the factors affecting efficient functioning of clay material for containment of landfill materials. The study of liner-leacheate interaction is done from the consolidation and vane shear tests on various clays having different activities, and chemicals that are typically found in a municipal solid waste leachate and a leachate collected from an active landfill.

An effort was made to study the use of Atterberg limits to predict the suitability of a clay as a landfill liner for a given waste environment. The study indicates that there is a decrease in permeability of bentonite …

Simulation Of A Microprocessor Controlled Drill Press, Arun J. Ayyagari

Theses

The concept of flexible manufacturing systems has ushered new dimensions into machine tool design. The power of this new technique is that a high degree of flexibility in a machine tool can be easily achieved by developing a software based control system as against conventional hard wired systems in existence.

To demonstrate this point, a microprocessor based control system is developed, in this thesis, to control the automated drill press. The Motorola MC6808 8-bit microprocessor is chosen as an example.

The microprocessor first evaluates the optimum cutting parameters for the given cutter size, work material and operation. It then uses …

Dynamic Laryngeal Analysis : Hardware And Software, Augustine Chan

Theses

A data acquisition and analysis system has been built and tested for the study of laryngeal dynamics: The system uses a computer to control the digitizing rate and to coordinate the pitch prompting for the subject. Tokens of steady state laryngeal vibration are obtained from an electroglottograph when the subject intones a series of computer prompted pitches in a musically scalar sequence. The system digitize the data at a basic rate of 200 samples per laryngeal cycle: This procedure enables the system to perform a modal analysis of laryngeal function: The signal processing and analysis procedure developed displays voice registration …

Design And Construction Of An Atomic Nitrogen Source For Ion Cluster Beam Deposition Of Thin Film Nitrides, Sahar Elgharib

Theses

The objective of this thesis research was to generate atomic nitrogen to react with Ga being deposited by an Ion Cluster Beam method to prepare GaN thin films. An experimental reactor was designed and constructed to generate atomic nitrogen by making use of a microwave induced discharge to dissociate molecular nitrogen into atomic nitrogen. The concentration and the flow rate of the atomic nitrogen arriving at the substrate were measured by titration with nitrous oxide. The experiments were done with 0.32 square cm quartz tubing at room temperature over the nitrogen pressure range from 0.14 torr to 0.56 torr. Results …

Analysis And Evaluation Of The Developments In The Use Of Coal, Farid Najib Elkheshen

Theses

This thesis is a survey and evaluation of the developments in the use of coal. It deals with the social, economic, physical, and biological impacts of such a shift. It examines the complete coal system, from extraction to combustion, including the key steps and policy initiatives. The United States, with 6% of the world's population, consumes about 33% of its commerical energy supply - while the available reserve coal is about 80% of total energy in the United States, with coal use representing only 17%, oil and gas about 78% at present.

Technologies under development that might reduce costs, increase …

Effects Of Adhesion On The Active Pressure Exerted On A Retaining Wall, Thomas G. Gallagher

Theses

This paper investigated the effect of adhesion on the active pressure behind a retaining wall. No equation existed to solve for the active pressure for a sloped backfill that also takes into consideration cohesive and adhesive forces on a failure wedge. The trial—wedge solution(Culmann method) considers these parameters, but since it is a trial and error method it takes up too much time to solve. A shorter solution is desirable. An equation for the active pressure in terms of ρ(angle between horizontal and failure plane) was derived. A closed form solution for earth pressure was developed by setting the derivative …

Moderating Online Conferences, Revised Manuscript, Computerized Conferencing & Communications Center, Elaine B. Kerr

Computerized Conferencing and Communications Center Reports

While considerable lore has accumulated about effective leadership techniques for groups interacting electronically, until now it has not been systematically presented. This material is culled from the experiences of those who have moderated past online conferences, the knowledge common to the EIES User Consultants, and observed behavior from thousands of conferences convened on EIES in the past. While this is a system-specific guide, the general principles ought to be generalizable to other systems, with different structures for group discussion.

Robert Burns put it well:
The best laid schemes o' mice and men
Gang aft a-gley;
An' lea'e us nought but …

Graduate Catalog 1986-1988 New Jersey Institute Of Technology: The Technological University Of New Jersey, New Jersey Institute Of Technology

Course Catalogs

No abstract provided.

New Jersey Institute Of Technology, Undergraduate Catalog, 1985-1987, New Jersey Institute Of Technology

Course Catalogs

No abstract provided.

Determination Of Trace Quantities Of Selenium And Arsenic In Canned Tuna Fish Using Electroanalytical Techniques, Ann Marie Higham

Theses

Toxic metals are present in the environment and are known to be present in food. Selenium, which is considered an essential micronutrient, is recognized as a toxic metal at slightly higher concentrations. Arsenic is also recognized as a toxic metal. Selenium and Arsenic tend to accumulate in food, specifically fish and seafood.

Fifteen brands and types of tuna fish were analyzed for selenium using differential pulse cathodic stripping voltammetry. The cans with the high and low concentrations of selenium were analyzed for arsenic using differential pulse polarography. Three samples with three percent recoveries and a blank were analyzed for each …

Integrating Working At Home With Information Systems Management, Computerized Conferencing & Communications Center, Joseph C. Schuh

Computerized Conferencing and Communications Center Reports

The history of computerization has its origin in the automation of manual processes - searching out the segments that could be put on a computer. The intended result was that the entire job would be done faster and cheaper. Thus, current computer-based information systems tend to make more efficient use of computers than people. The management function, on the other hand, often seems to focus on competitive skills and salesmanship rather than on the ability to attract and hold talented people. But, such impersonal factors that have driven management practices are changing. There has been a complete reversal in the …

An Industrial Ethanol Azeotropic Distillation Process : Modeling, Analysis, And Simulation, Harpreet Singh Chawla

Dissertations

A steady state process simulator with extensive capabilities was developed for the simulation of process plants involving non-ideal multicomponent systems. A comprehensive stand alone program was developed to represent process systems encountering three phases. A computer program was also developed to handle simultaneous regression of vapor-liquid and liquid-liquid equilibria data to estimate the liquid phase activity coefficients via a global set of parameters for the ethanol azeotropic distillation process, using benzene as the entrainer.

An industrial ethanol azeotropic distillation process has been simulated using the developed process simulator (PROSIM). A study of the azeotropic column's aqueous ethanol feed composition reveals …

Further Development Of Preparation And Measurement Techniques For Triode-Sputtered Mercury Cadmium Telluride Thin Films, Tai-On Chan

Theses

The modified MRC 8800 R.F. triode sputtering system was used for mercury vapor sputtering (Hg^1-xCd^x)Te targets onto N-type (111) silicon substrates with a resistivity of 70 to 90 ohm-cm. Deposition rates were in the 2.6 to 3.6 A/sec range, A Hall mobility value, at 87°K, of 2550 Cm²/V•sec with a carrier concentration of 7(10¹⁵) cm^-3 was obtained for 9 μm thick films with an X-value of 0.25. Obtaining good sputtered films reliably was dependent on having targets that would not crack when bombarded with mercury ions. Improvements in the methods used …

Computer Analysis On Discontinuity Of Cylindrical Pressure Vessels With Various Heads, Ku-Shiang Sheu

Theses

This thesis uses FORTRAN programs to compute the maximum shear stresses of the cylindrical pressure vessel with various heads. They are cylindrical, spherical, ellipsoidal, flat and conic shapes. Also the maximum shear stresses for the bimetallic joints at the vessel wall and away from the vessel wall are analyzed. Numerical examples are given for each case to facilitate the applications.

A Survey Of The Literature On Moisture In Building Construction, Lawrence Charles Tiboldo

Theses

The aim of this thesis was to evaluate the literature on moisture in buildings for its usefulness in the understanding of the theory involved in moisture transfer in buildings. Because analysis of the effects of moisture migration and development of condensation control strategies in structures depends on the knowledge of heat and moisture transfer theory as well as on the documented data on building material properties, evaluation of the usefulness of the reference material will serve as an indication of the availability of pertinent information.

To fulfill this objective, the literature listed as references to Chapter 21 of the 1985 …

An Investigation Of The Application Of Utility Theory To Determine The Value Of Time: The Demand For Interactive Information Systems In Student Markets, Gordon S. Kalley

Theses

The economic rational of many contemporary businesses is the provision of services or labor saving equipment which their customers' pay for in order• to save themselves time. A major decision such an enterprise must make prior to entry into the market i=_ whether enough of a market exists to make its entry worthwhile. Such firms would be able to make better resource allocation decisions if they could have a quantitative measure of the relationship of their consumer's valuation of time vis a vi money. This study proposes such a measure.

Interactive information systems, whose viability depends to a large degree …

Reliability Evaluation Of Liquid Crystal Displays Under Accelerated Test Conditions, Ravi Sankar Kalyandrug

Theses

This study has determined the effects of high temperature and humidity on the reliability of liquid crystal dis-plays.

Reliability life testing was done on variety of LCD samples under different operating conditions. All the besting was done under accelerated conditions, including high temperature of 85°C and relative humidity of 70%. A number of failure modes were identified in the long series'of tests.

Among many failure modes such as peeling of seal, degradation of polarizers etc., the most important is the degradation of alignment of liquid crystal molecules. Leakage current measurements were made on all the LCD samples before and after …

Model Experiment Of Rock Fracturing Caused By Driving Piles, Dai-Heyng Lee

Theses

The geotechical construction problem of rock fracturing caused by pile driving is investigated using a laboratory model. One inch diameter closed bottom steel pipes were driven into a simulated rock mass consisting of masonry bricks having an average compressive strength 3,200 psi. Both single pile and five pile model groups were tested. The single pile tests indicated that a threshold of penetration behavior occurred at a theorical hammer energy of 100 ft-lb and this was used for the group tests. Penetration rates were measured using an optical level.

Piles in the five pile model group were initially driven to a …

Basic Concepts In Cad & Cam, Chao-Ming Liu

Theses

As the computer revolution is nearing its end, CAD/CAM concepts are being widely accepted and evolving rapidly. This thesis begins with a disscussion of the significance and advantages of CAD/CAM and their relationship with automation. Hardware and software components involved are then introduced. Product design under CAD is done by computers. Computers perform engineering analysis, necessary calculations, and dynamic simulation to complete the complex design. The geometric elements and operational primitives are provided by a data base system. The major components of CAM are then introduced. The term CAM is used in a broader sense to include CAPP, MRP, NC, …