Digital Commons Network^™

Volatilization Of Contaminants From Wastewater, Shaoyan Wu

Theses

Emission of volatile organic compounds (VOCs) from many industrial wastewater treatment facilities are a major source of air pollution, and getting much attention from EPA. In order to determine "Best Available Control Technology" and "Lowest Achievable Emission Rate" for controlling emissions of VOCs from industrial wastewater, the accurate estimation of VOCs emission rate and realistic modeling of contaminant volatilization are required.

In this research, the volatilization of three compounds (Toluene, Xylene, and Aniline) were studied under varying aeration, stirring, and quiescent scenarios. The concentrations of contaminant were analyzed by HPLC. Experimental rate constants were obtained by using the first order …

Improvement Of Waterjet And Abrasive Waterjet Nozzle, Zheng Li

Dissertations

This investigation is concerned with the improvement of the nozzle design for water and abrasive water jet machining. The mechanism of formation and characteristics of pure water and abrasive water jets are investigated in order to determine quasi-optimal process conditions.

To improve the pure water jet machining, a pulsed water jet nozzle, which employs the principle of the Helmholtz type resonator, is investigated experimentally and numerically. The experiments show the advantages of this nozzle over the commercial nozzle in cutting and cleaning. A numerical solution of the differential equations of continuity, momentum conservation, turbulent kinetic energy and dissipation for two …

Analytical And Simulation Models Of Weaving Area Operations Under Non-Freeway Conditions, Muhammad Shahid Iqbal

Dissertations

The Highway Capacity Manual covers adequately the operation of weaving areas on freeways. Weaving on non-freeway facilities, however, has not been addressed as yet. This research effort presents a state-of-the-art procedural analytical approach and simulation models for the analysis of the level of service and operation of non-freeway weaving areas. Weaving under non-freeway conditions is classified into two broad categories; basic weave and ramp weave. The analytical models for these two weaving categories are calibrated and validated based on data obtained from several sites selected in the states of New Jersey and New York. New level of service criteria are …

Local Thermal Stress Factor Of Pipe-Nozzle, David Chihwei Chen

Dissertations

A comprehensive study of local thermal stresses at the juncture of pipe-nozzle is presented in this thesis. The thermal loading is assumed to be a linear thermal gradient across the thickness of the pipe and nozzle. Currently, there exists neither experimental nor analytical data that is sufficient for pressure vessel designers to analyze the local thermal stresses at the juncture of pipe-nozzle. In order to provide a comprehensive database to calculate these thermal stresses, the finite element technique is used to provide a series of local thermal stress factor plots as a function of pipe-nozzle geometrical parameters.

For the local …

An Office Document Retrieval System With The Capability Of Processing Incomplete And Vague Queries, Qianhong Liu

Dissertations

TEXPROS (TEXt PROcessing System) is an intelligent document processing system. The system is a combination of filing and retrieval systems, which supports storing, classifying, categorizing, retrieving and reproducing documents, as well as extracting, browsing, retrieving and synthesizing information from a variety of documents. This dissertation presents a retrieval system for TEXPROS, which is capable of processing incomplete or vague queries and providing semantically meaningful responses to the users. The design of the retrieval system is highly integrated with various mechanisms for achieving these goals. First, a system catalog including a thesaurus is used to store the knowledge about the database. …

Local Stress Factors Of Pipe-Nozzle Under Internal Pressure, Jih-Lian Jack Ha

Dissertations

This thesis presents a comprehensive study of local stresses around a pipe-nozzle due to internal pressure. The finite element method (FEM) was employed to provide a numerical solution which will furnish a database for stress analysts to compute local stresses of pipe-nozzle due to internal pressure. The local pressure stresses for both the pipe and the nozzle around the pipe-nozzle juncture are first normalized into pressure stress factors which are then plotted as functions of geometrical parameters, beta, β, (nozzle mean radius / pipe mean radius) and gamma γ, (pipe mean radius / pipe thickness). These local pressure stresses at …

Autonomic Nervous System Evaluation Using Time-Frequency Analysis, Sanjay Fernando

Theses

Spectral analysis of heartrate variability (HRV) provided an estimate of the sympathetic and parasympatheticinfluences on heart rate without drugs or other invasive procedures.However, there are many situations where heart rate changed rapidlyover time and the control of those changes was of considerable interest.Time-frequency analysis was utilized to expand the concept of spectralanalysis of HRV to describe changes in vagal tone and sympatho-vagalbalance as a function of time. As a result the assessment of the autonomicnervous system during rapid changes in heart rate was made.

There were three advantagesto calculating vagal tone and sympatho-vagal balance by using timefrequencyanalysis. First, vagal tone …

Characterization Of Sleep Eeg, Seetharamiah Sateesh

Theses

The physiological relationship between the various components of sleep and its variation due to drug administration has been used as one of the primary tools to analyze the performance of drug. A number of studies have been performed in recent years in this direction. Electroencephalogram (EEG) has been characterized with the help of variables ranging from measurements of the duration of different sleep stages to the activities that define the stages themselves. Advances in computer hardware and software have improved the methods of data acquisition and storage. Analysis of long stretch of data has always been a problem considering the …

Building Oriented Surface Generation Through Iges Specification, Jujiang Bao

Theses

This thesis focuses the use of Initial Graphics Exchange Specification to generate automatically three dimensional surfaces. Currently, different CAD systems utilize their own data formats to generate graphic databases which are not compatible with one another. Besides, most of the existing CAD systems require an interactive data input process which is very much time consuming. In order to solve above problems, an efficient algorithm has been developed in this research to automatically generate portable graphic database following ICES specifications. This portable graphic database can be adopted by different commercial CAD/CAM systems. Using the proposed method, the current design process can …

Influences Of Cardiac And Respiratory Parameters On Heart Rate Variability, Melissa Leifer

Theses

Heart rate variability is a result of variation in the activity of the sympathetic and parasympathetic nervous systems. Methods have been developed to determine the level of parasympathetic activity by observing the heart rate variability spectrum. Most of the previously published research uses only level of parasympathetic activity and respiratory rate to draw conclusions about the interactions of the autonomic nervous system with physiological parameters. In order to gain a complete understanding of the autonomic nervous system and the mechanisms responsible for heart rate variability, respiratory volume, cardiac variables and pulmonary variables need to be considered. In addition, amount of …

Mbe Growth Of Inxga1-Xas/Gaas/Si Heterostructure System, Jun Liu

Theses

In this work, we grew the In_xGa_1-xAs/GaAs/Si (GaAs as buffer layer) by MBE technique. The surface of the buffer layer became microscopically rough as the thickness of the buffer layer increased and the growth mode of GaAs on Si underwent a change from three-dimensional to two-dimensional during the initial growth stage as indicated on the Reflection High Energy Electron Diffraction (RHEED) screen. The Scattering Electron Microscopy (SEM) observation of the etched surface of GaAs on Si showed that the structure of the buffer layer tended to be poly-crystalline and it was possible that a predominant orientation …

Subthreshold Channel Leakage Current In Gaas Mesfet's, Wei Long

Theses

In this thesis, a physical model including the subthreshold conpensation properties is presented. The Poisson equation is solved analytically in one dimension for GaAs MESFET's with undoped substrates in the subthreshold region. The solution is then used to derive expressions for subthreshold drain current and subshreshold swing in MESFET's with undoped substrates. Very good agreement between experimental and analytical results is achieved.

Two key parameters (Nilo and Iso) that determine the subthreshold Characteristics have been analyzed as a function of residual acceptor concentration Na, deep level EL2 concentration Nt, channel doping concentration Nd and threshold voltage Vt. It is shown …

Computerized Scoring Of Sleep Stage Data, Subbarao Narayana

Theses

Sleep is a non-uniform biological state which has been subdivided into different stages. The basic criteria behind staging are the amplitude and frequency variations of sleep data. The sleep analysis is carried out by considering the characteristic variation of all three EEG, EOG and EMG signals. The polygraphic recording of nocturnal sleep is a method of research widely used in neurophysiology laboratories, both for the clinical study of sleep and for the evaluation of the therapeutic effectiveness of drugs acting on sleep. The analysis of this method is carried out by an expert individual whose depth of knowledge regarding the …

Continuous Monitoring Of Volatile Organic Compounds In Air Emission Using Membrane Extraction Microtrap Gc System, Xin Zhang

Theses

A novel method for continuous monitoring volatile organic compounds (VOCs) in air at trace level is presented. A membrane module and a microtrap were used along with gas chromatographic analysis. The membrane module consisted of a bundle of silicone rubber hollow fibers and separated the VOCs from the gaseous stream. The microtrap which is a very small adsorbent trap played the roles of preconcentrator and injector. The VOCs selectively permeate across the membrane into a strip gas in the membrane module. Before entering the GC column, the VOCs are trapped and concentrated by the microtrap. Desorption of the VOCs is …

Passive Radiosonde Transducer Design For Remote Pressure Sensing Applications, Yang Gao

Theses

Intracranial pressure can be measured to accuracies within 1 milliTorr using passive microtransponders that are micromachined using silicon as a base technology. These microtransponders can operate with either a dual-oscillator or a phase-locked loop frequency scanned control system.

The current work describes the design of a totally implantable microsensor for biomedical applications with the aim to monitor and measure the epidural intracranial pressure . The implanting microsensor is basically an RLC device in which capacitance varies with fluid pressure. The resonant frequency of RLC Series connected device varies with chemically etched diaphragm electrode spacing and thereby measures the variations with …

Processor Allocation For Partitionable Multiprocessor Systems, Nicholaos C. Antoniou

Theses

The processor allocation problem in an n-dimensional hypercube multipro-cessor is similar to the conventional memory allocation problem. The main objective is to maximize the utilization of available resources as well as minimize the inherent system fragmentation. In this thesis, a new processor allocation strategy is proposed, and compared with the existing strategies, such as, the Buddy strategy, the Single Gray Code strategy (SGC), the Multiple Gray Code (MGC), and the Maximal Set of Subcubes (MSS). We will show that our proposed processor allocation strategy outperforms the existing strategies, by having the advantage of being able to allocate unused processors to …

Control Of Smart Structure Using Adaptive Dither, Tian Hong

Theses

In this thesis, a mathematical model of a piezoelectric stack actuator is presented to describe its voltage versus displacement hysteresis characteristices. This model can accommodate a wide range of piezoelectric materials, including the PZT (lead zirconate-lead titanate) type which is most popular in industrial applications.

Besides describing the conventional "single-loop" hysteresis, this model also accounts for the off-axis minor loops by augmenting the algorithm with loop indexing.

It is shown that the PZT hysteresis possesses certain "weak scalability" that enables the use of spectral analysis to measure the level of nonlinearity.

After a suitable mathematical model has been obtained, a …

Cad Study Of Linear Tapered Slot Antenna, Anthony W. Kwan

Theses

Linear Tapered Slot Antenna (LTSA) is an attractive candidate as a radiating element in frequency scanning arrays. LTSA element backed by a rectangular cavity had been investigated and is proven to posses various physical design parameters suitable to optimize its performance. This study is focused on the feed position variation to optimize the performance while maximum of the current density variation is maintained in the slot region. It was observed that if the stub base of the microstrip feed structure is located in the middle of the slot region, current maximum can be obtained within the slot region at the …

Measurement Of The Hall Coefficient And Electron Mobility Using Van Der Pauw Type Hall Effect Measurements, Hong-Sheng Luo

Theses

Hall effect measurement in the electrical characterization of semiconductor materials is very important. We set up the Hall effect measurement system and examined the system with a standard sample. The experimental results show that this Hall measurement system worked as well as expected. We also used this system to study the GaAs/GaAs and InGaAs/GaAs which grown by MBE. Finally, we disscussed and consided some common problems of Hall measurement. Some useful formulas and plots are presented.

The Influence Of Hydrodynamics And Particle Size On The Rejection Properties Of Ultrafiltration Membranes, Usama M. Shahin

Theses

A mathematical model based on the flow hydrodynamics is developed to calculate the treatment efficiency of ultrafiltration process. This model relates the treatment efficiency with the consideration of both fixed parameters and variable parameters. The fixed parameters are function of the intrinsic rejection coefficient, diffusion coefficient, and viscosity whereas the variable parameters can be related to the fluid velocity, volume flux, and cartridge dimensions. The model has been examined by solutions with solutes that have different molecular weights. The experimental data fits the proposed mathematical model very closely suggesting its suitability to evaluate the rejection efficiency in ultrafiltration. As such …

The Use And Evaluation Of Cleaner Wicks To Accelerate In Situ Bioremediation Of Organically Contaminated Groundwater And Soil, Brian Michael Sielski

Theses

The adaptation of Cleaner Wicks to accelerate in situ bioremediation of organically contaminated ground water and soil can be accomplished by making minor modifications to the Cleaner Wick design.

Once these changes in the Cleaner Wick design have been made the two primary ingredients necessary for aerobic microorganisms, nutrients and oxygen, can be delivered via the Cleaner Wick to the subsurface environment both above and below the water table to stimulate microbial growth and activity. Therefore, the microbial population will be able to biodegrade the target contaminants, rendering them harmless products such as carbon dioxide and water.

An adequate understanding …

Behavior Of Concrete And Slender Reinforced Concrete Columns Under Cyclic Axial Compression With Bidirectional Eccentricities, Byong Youl Bahn

Dissertations

A rational analysis of reinforced concrete (R/C) structures requires satisfactory modeling of the behavior of concrete under general loading patterns. The behavioral characteristics of concrete dominantly depends upon its load history. For the study of concrete behavior, parametric study and experimental investigation into the behavior of concrete under load history of random cycles are performed. Through parametric study, the applicability of the previous concrete models is examined and a physically motivated modeling for the cyclic stress-strain relationships is proposed. The present modeling of concrete under general cyclic loading is initiated to provide substantial applicability, flexibility of mathematical expressions and furthermore …

Theoretical Evaluation Of The Break Off Test For Concrete, Arjuna Priyara Ranasinghe

Dissertations

Strength of concrete is normally measured using the standard cylinder or cube. The measured strength is used for design. The accuracy of concrete strength is frequently challenged, particularly in large concrete structures where size effect of the test specimens is attributed for the differences. Many nondestructive tests were developed to evaluate concrete strengths. In recent years, it was obvious that these tests are unreliable. As the infrastructure decays, more nondestructive tests are required to evaluate the existing structures.

The Break Off Test is a recently developed nondestructive test. Although substantial amount of experimental investigations have been carried out on this …

Undergraduate Catalog, 1994-1997, New Jersey Institute Of Technology, New Jersey Institute Of Technology

Course Catalogs

No abstract provided.

Oxidation Of Pollutants In A Batch Recirculation Bioreactor With Immobilized Microorganisms, Jongtai Jung

Dissertations

The purpose of this work was to study bio-oxidative destruction of several substrates in an immobilized cell batch bioreactor in recirculation configuration. This system was used in three cases: a series of substrates usually used as monomers, ethylene glycol and its tetramer, and phenol under magnetic irradiation. In addition, kinetic studies were performed and experimental versus predicted results compared.

The substances styrene, methyl methacrylate (MMA), and β-hydroxybutyric acid (HBA), common monomers, were biologically treated using an acclimated mixed microbial community immobilized in calcium alginate gel. A comparison of biodegradation rates (3.3, 9.4, and 15 ppm/hr for styrene, MMA, and HBA, …

Motion Estimation Using Optical Flow Field, Jingning Pan

Dissertations

Over the last decade, many low-level vision algorithms have been devised for extracting depth from intensity images. Most of them are based on motion of the rigid observer. Translation and rotation are constants with respect to space coordinates. When multi-objects move and/or the objects change shape, the algorithms cannot be used.

In this dissertation, we develop a new robust framework for the determination of dense 3-D position and motion fields from a stereo image sequence. The framework is based on unified optical flow field (UOFF). In the UOFF approach, a four frame mode is used to compute six dense 3-D …

Adaptive Nonlinear Control Using Fuzzy Logic And Neural Networks, Shu-Chieh Chang

Dissertations

The problem of adaptive nonlinear control, i.e. the control of nonlinear dynamic systems with unknown parameters, is considered. Current techniques usually assume that either the control system is linearizable or the type of nonlinearity is known. This results in poor control quality for many practical problems. Moreover, the control system design becomes too complex for a practicing engineer. The objective of this thesis is to provide a practical, systematic approach for solving the problem of identification and control of nonlinear systems with unknown parameters, when the explicit linear parametrization is either unknown or impossible.

Fuzzy logic (FL) and neural networks …

Estimation And Cancellation Of Friction In Control Systems, Sofia Mentzelopoulou

Dissertations

The research reported in this dissertation concerns the estimation and cancellation of friction in control systems. For purposes of analysis, the Coulomb friction model, the "extended" Coulomb friction model as well as dynamic friction models are used. In addition, for systems with multiple degrees-of-freedom, a general matrix representation of friction is presented.

For the design of the friction estimators, the theory of nonlinear observers is applied. In particular, for a system with multiple degrees-of-freedom, holonomic constraints, and multiple friction sources, three different observers are presented to estimate the friction force or torque. The first (Generalized Coulomb Friction Observer) is designed …

Engineering Analysis Of A Packed-Bed Biofilter For Removal Of Volatile Organic Compound (Voc) Emissions, Zarook M. Shareefdeen

Dissertations

This study dealt with removal of VOC emissions from airstreams using an evolving new technology which is known as biofiltration. The basis of this technology is biodegradation of VOCs in biofilms formed around porous solids which are placed in packed-bed reactors.

A detailed model describing steady state biofiltration of single and mixed VOCs was developed, and experimentally validated. The model takes into account biodegradation kinetics, the effect of oxygen, kinetic interactions among structurally similar compounds, and mass transfer from the gas phase to the biolayer. It was found that oxygen (a factor neglected in all previous studies) plays a very …

Biological Denitrification : Fundamental Kinetic Studies, And Process Analysis For Sequencing Batch Reactor Operation, Jun-Hsien Wang

Dissertations

This study dealt with a detailed investigation of biological denitrification of nitrate and nitrite by a pure culture of Pseudomonas denitrificans (ATCC 13867), under anaerobic conditions.

In the first part of the study, the kinetics of denitrification were studied in serum-bottle experiments. It was found that reduction of both nitrate and nitrite follows inhibitory expressions of the Andrews type. It was also found that when nitrite is present at levels above 15 mg/L, nitrite and nitrate are involved in a cross-inhibitory, non-competitive, interaction pattern. Analysis of the kinetic data has shown that the culture used has severe maintenance requirements, which …