Digital Commons Network^™

A Study Of Segregation In Cast Aluminum-Uranium Alloys, B. L. Bramfitt

Masters Theses

"This investigation involves a photomicrographic study of the segregation resulting from the eutectic solidification characteristics of aluminum-uranium alloys, ranging from 5 to 30 weight percent uranium. The segregation can occur in either of two manners; the first, due to the gravitational forces acting upon the growing particles which nucleate in the melt and the second, due to the mode and rate of heat transfer through the material. It was found that segregation occurred only as the result of the latter factor due to the small volume of the ingot and the rapid rate of heat transfer. The segregation was measured …

An Evaluation Of The Resistance Element Method For Measuring Detonation Velocity Of An-Fo Mixtures Confined In Small Diameter Boreholes, William Stewart Breakey

Masters Theses

"Instrumentation and techniques employing a constant current in a 4 ft. length of Nichrome resistance wire embedded in an explosive mixture were developed to measure detonation velocity in small diameter boreholes.

The resistance element technique was evaluated by detonating mixtures in iron and clay pipes, and it was shown that the current in the circuit was not constant. Velocity measurements varied from 8,000 fps to 16,000 fps. Low velocity material provided poor time - voltage traces.

The resistance element method was compared to a pin oscillograph technique, and an explanation was offered for observed differences in velocity. The standard deviation …

Shear Stress Distribution In Haunched Beam Models, Manyu K. Mehta

Masters Theses

"The purpose of this thesis has been to give the distribution of shear stress inside a haunch. A haunch is generally provided to relieve high stress concentrations at the face of the column. However the nature of shear stress distribution inside the haunch is not known.

This stress distribution was determined from a photo- elastic study on a CR-39 model. It is noted that the haunch reduces the stress concentration at the face of the column but at the same time somewhere near the point where the haunch meets the beam there is a high stress concentration.

Shear stress changes …

A Weight Loss Technique For The Determination Of Phase Boundaries, Robert Lee Benner

Masters Theses

"An apparatus has been designed and constructed that would continuously record the weight loss of a sample in a flowing inert atmosphere, at a constant temperature.

A technique has been developed to determine the phase boundaries of a binary phase diagram.

Alloys of the magnesium-nickel, cadmium-antimony, copper-cadmium, copper-zinc, and magnesium-zirconium systems were subjected to investigation to verify the operation and resolve a number of limitations of the equipment.

These investigations disclosed that the apparatus gave the best results with alloys having vapor pressures in the range between 1 and 35 millimeters of mercury"--Abstract, page 2.

Stylolites And Sedimentary Structures In The Cave-In-Rock Fluorspar District, Southern Illinois, Won Choon Park

Masters Theses

"This thesis deals with stylolites, slump structures, sulfides in the oolitic limestone, and geometry of the bedded fluorite deposits in the Cave-In-Rock fluorspar district, southern Illinois. Stratigraphic zones studied were: 1) the upper part of the lower Fredonia limestone member, 2) the upper part of the upper Fredonia limestone member,,and 3) the upper part of the Renault formation.

Geometry of the ore rocks and related structures was investigated. Most of the ore is layered and constitutes part of the sedimentary strata.

Slump structures were observed and studied in detail. Most of the slump structures show evidence which indicates a sedimentary …

Commentary On The 1962 Edition, George Winter

American Iron and Steel Institute (AISI) Specifications, Standards, Manuals and Research Reports (1946 - present)

No abstract provided.

The Missouri Miner, October 06, 1961

The Missouri Miner Newspaper

No abstract provided.

Perfection Of The Lattice Of Dislocation-Free Silicon, Studied By The Lattice-Constant And Density Method, Martin E. Straumanis, Pierre Borgeaud, William Joseph James

Materials Science and Engineering Faculty Research & Creative Works

The lattice-constant and density method revealed that a high-purity silicon crystal free of dislocations has a perfect lattice without an excess of vacant sites or interstitials (n′=8.0000 4) within the limits of error, in agreement with the results obtained with the decoration method. The lattice constant of vacuum heated silicon powder of semiconductor purity was 5.43070±0.00004 A; that of the nonheat-treated powder was 5.43081 A at 25°C. The constants determined from crystal chips by the rotating crystal method were lower: between 5.43028-5.43048 A at 25°C. As the constants of each series of measurements could be reproduced very well (s=±0.00004 A), …

The Missouri Miner, May 12, 1961

The Missouri Miner Newspaper

No abstract provided.

The Missouri Miner, April 21, 1961

The Missouri Miner Newspaper

No abstract provided.

The Missouri Miner, April 07, 1961

The Missouri Miner Newspaper

No abstract provided.

Evaluation Of The Force Constants Of Non-Polar Gases From Viscosity Data, Kei-Sin Wei

Masters Theses

"The analytical expressions for the transport coefficients (i.e. viscosity, thermal conductivity, and diffusivity) of an ideal gas can be derived from the kinetic theory of gases. It is also possible to make these analytical expressions adequate for real gases if the intermolecular forces of attraction and repulsion for these gases have been taken into consideration.

The intermolecular forces have been studied by many investigators. The Lennard-Jones potential is one of the most realistic semi-empirical statements which represents particularly the intermolecular forces of attraction and repulsion for non-polar gases.

The values of the Lennard-Jones potential parameters or the force constants of …

Effect Of Lime & Cement Additives On The Dynamic Modulus Of Elasticity Of A Clay Soil, Ismail Yolar

Masters Theses

"This thesis is a study to determine the values and characteristics of modulus of elasticity and the modulus of rupture of a clay soil stabilized with lime and cement in an effort to pave the way for including these values in design criteria.

The modulus of elasticity and the Poisson's ratio were obtained by sonic method. Specimens were broken in flexure for modulus of rupture. Experiments were performed with; (1) untreated soil, (2) soil with 4, 6, and 12 percent cement additive, (3) soil with a 3 percent lime additive and 0, 4, 6, and 12 percent cement additive, (4) …

Geology Of The East-Central Portion Of The Nelson Quadrangle, Clark County, Nevada, Tedral Kantor

Masters Theses

"The purpose of this investigation was to determine the unusually complex geology of a little-known area south of the Eldorado mining district, southern Clark County, Nevada. The area, mapped at a scale of 1:24000, comprises a segment of the northerly-trending Eldorado mountains in the southeast corner of the Great Basin. This rugged desert area is on a drainage divide between the Great Basin and the Colorado River. The rocks of the area consist of Precambrian gneisses and schists invaded by successive generations of Upper Cretaceous (?) - Tertiary igneous rocks. The older rocks, mainly biotite-chlorite gneisses, have resulted from high-grade …

A Study Of The Difference Effects On Alpha Solid Solutions Of Oxygen In Titanium Dissolving In Hydrofluoric Acid, Kuo-Chin Chuang

Masters Theses

"Alpha solid solutions of oxygen in titanium dissolving in hydrofluoric acid exhibited a positive difference effect with k values of 5.7, being independent of the concentration of HF, within the compositional range studied 0 to 5 w/o oxygen. This indicates that various TiO_x alloys are polarizable to the same extent by the same strength of anodic current in hydrofluoric acid.

The difference effect observed on TiO_x alloys dissolving in HF-HCl revealed that the effect is dependent on the oxygen content of the solid solution as well as on the concentration of HCl. The presence of HCl results in …

Evaluation Of Protective Paint Films On Steel By X-Ray Diffraction Techniques, Donald Charles Knobeloch

Masters Theses

"Paints and related organic materials provide the most widely used means of protecting metals against corrosion. While corrosion measurements are based on a full range of quantitative methods in physical and analytical chemistry, the basic problem of evaluation work in the field of paint chemistry has been characterized by empirical testing procedures. Field tests are still of major importance and secondly, the relative value of paints may be predicted through exacting laboratory tests. However, the results of accelerated exposure tests have never successfully been correlated with service experience despite the efforts of many laboratories over a period of 35 years …

An Investigation Of The Factors Influencing The Design Of A Dense Prilled Ammonium Nitrate-Fuel Oil Mixture, Robert Bartley Hopler Jr.

Masters Theses

"The physical characteristics of dense ammonium nitrate prills were examined. The density was found to be 1.52 grams per cubic centimeter, and from this the specific surface was calculated for the size fractions of interest in the investigation. Theoretical loading densities were calculated for between 26.0 and 47.6 percent voids.

The explosive properties of discrete particle size fractions were investigated. The equation by Clark was found to predict the detonation velocity of the sizes smaller than 8/20 mesh. The equation by Cook could not be applied to dense prilled ammonium nitrate. The possibility of a very oxygen negative condition existing …

A Study Of Viscous Frictional Effects And Relay Characteristics On The Operation Of A Positional Relay Servomechanism, Earl F. Richards

Masters Theses

"The thesis describes some experimentally observed data and analytical approaches to the study of a relay servomechanism. The experimental data were secured from an analog simulation of a relay servo system. The results of this data were compared to the transient approach by use of the phase-plane method. The stability of the system was determined using a describing-function. The analytical approaches are described in the presentation.

A study of the effects of viscous friction is described, and the characteristic of the relay used in the system is given special attention. The response to input driving function was considered, and rise …

Correlation Of Dust-Count Results By Zeiss Konimeter And Midget Impinger, Chandmal Jain

Masters Theses

"In this modern age, the scientific and technological developments have advanced mechanized mining to the status wherein the attendant dust problems have reached very serious hazard proportions. The significant roles, which have been perfected for the Zeiss konimeter and the midget impinger, in evaluating dust concentrations and thereby revealing possible improvements in making the atmospheric conditions safer, cannot be over emphasized.

While introducing the subject of this paper in the first chapter, the author has presented a historical resume, wherein he pointed out that performances of these instruments have not been correlated in the past. However, the work reported on …

Isothermal Decomposition Of Austenite (In 1.4% Tungsten Steel) At Subcritical Temperatures, Samir Moustafa Riad

Masters Theses

"An experimental investigation was conducted in order to study the relationship between temperature, time and the decomposition of austenite in Tungsten steel of a given composition - and to plot the T-T-T Diagram for this steel.

The steel was prepared, homogenized and cut into identical specimens for further heat treatment and metallographic inspection. Precautions were taken to prevent these specimens from decarburizing during any heat treatment.

This experimental work may be divided into three main parts:-

I. Determination of the critical temperature range; i.e. the range of temperature Ae₁ and Ae₃ above which austenite is stable and below …

A Study Of The Transient State Of Transpiration Cooling, William C. Wolkenhauer

Masters Theses

"This thesis is a successful attempt to show a new approach to the transpiration cooling problem. Transpiration cooling has long been known as an effective way of removing heat from porous material.

It is shown here that transpiration cooling from a porous material, assuming a temperature difference between the coolant and the porous material, is less effective than where the coolant within the pores is assumed to be at the same temperature as the material adjacent to the pore. Previous investigators made the latter assumption.

The specific problem considered here is that of a uniform, porous plate with constant physical …

An Analog Method For The Determination Of The Deflection Of Beams Resting On End Supports And Design Of An Automatic Programming Device, Paul C. Jackson Jr.

Masters Theses

"This investigation shows that beam problems can be solved easily and accurately with an analog computer. Two problems were solved as to their shear, moment, slope and deflection along the length of the beam and the graphs drawn by the analog computer were compared with calculated values. Very little difference was found between them.

An electronic programmer was built to aid in handling beam problems as they were being run on the computer. This was capable of putting into the computer bits of data at specified intervals of time. The programmer proved reliable and repeatable once it was adjusted to …

Investigation Of Vertical Internal Spillways, Paul R. Munger

Masters Theses

"This investigation resulted in the development of a means of predicting the discharge of water through an internal spillway type rockfill dam. From the data obtained during the various tests, equations were developed by which the coefficient of discharge for an internal spillway type rockfill dam can be determined when the core height, rock size and head causing flow are known. The equations give results with an error of less than 5%, which is adequate for engineering works"--Abstract, page 2.

Electron Microscope Study Of The Systems Cadmium-Cadmium Chloride And Lead-Lead Chloride, Dennis O'Neill

Masters Theses

"The nature of the dispersed phase in the cadmium-cadmium chloride and lead-lead, chloride systems were investigated with the electron microscope.

Preliminary experiments on preparing and examining the dispersed phase showed that it was most feasible to study the material by electron-microscopic examination of replicas made from the surfaces of the fractured materials. Melting apparatus and methods were chosen so that samples of the melts could be easily quenched to different temperatures and so that the samples could be easily fractured with a minimum of surface contamination. Of the conventional replicating techniques tried, that of carbon replicas pre-shadowed with chromium was …

Apparatus For Inductive-Electromagnetic Model Studies, Won Ho Kim

Masters Theses

"The object of this research is to design, construct and calibrate an apparatus suitable for electromagnetic model studies. A portion of the thesis is devoted to general review and theoretical consideration of electromagnetic prospecting.

Theoretical analysis of electromagnetic survey data by mathematical methods can only be carried out for simple idealized subsurface conditions. Because of the difficulties of theoretical solutions, in contrast to the simplicity of the conditions of similitude in electromagnetic exploration, a model experiment offers a very useful means of studying and comparing the response of naturally occuring conducting mineral bodies.

An apparatus suitable for inductive-electromagnetic model studies …

A Vacuum Induction Furnace For Pyrometric Cone Equivalent Determinations, Robert E. Farris

Masters Theses

"Various furnaces which are commonly used for P.C.E. determinations were compared from a literature review. The inadequacies of these furnaces were noted and a furnace was designed, constructed, and evaluated in an effort to minimize or eliminate some of the indicated problems. For this furnace heat is developed in opposed cones (susceptors), which are fabricated from 0.005” molybdenum sheet, by induced (induction) currents from a 10 KW vacuum tube generator. The furnace components are enveloped by a pyrex cylinder in which a vacuum (approximately 1 to 5 micron pressure absolute) is maintained during operation"--Abstract, page ii.

The Effect Of Phosphoric Acid On Compaction And Shear Characteristics Of Pure Kaolin Clay, Bhupat Hargovinddas Mehta

Masters Theses

"The work presented is the investigation of the effect of phosphoric acid on the compaction and shear characteristics of pure kaolin. Pure Georgia kaolin clay average particle size of five microns was mixed with different percentages of phosphoric acid. These mixtures were permitted to react for varying periods of time. The results of the study indicate a notable and gradual increase in dry density of the kaolin with increasing percentages of phosphoric acid admixture. The acid admixture ranges from one up to nine percent of the dry weight of the clay. Increase in cohesion of the clay with increase of …

Explosive Performance Parameters: A Digital Computer Solution And Error Analysis, Robert T. Stelloh

Masters Theses

"A program was written for the determination of explosive performance parameters on the Royal-McBee LGP-30 electronic digital computer. The method developed by Dr. M. A. Cook was used, which is based on the thermohydrodynamic theory of detonation. This theory and the specific equations developed by Cook are presented.

General statements are made in regard to computer programming, and specific information given concerning the programming concepts used for this particular problem. A detailed explanation of the program operation is given, together with the tabular data required for its use.

Equations are presented for an analysis of the effects of roundoff error …

A Preferred Orientation Study Of Sheet Formed By Rolling Copper, Nickel, Titanium And Tungsten Metal Powders, Martin Franklin Marchbanks

Masters Theses

"Pole figure scans of strip rolled from copper, nickel, titanium, and tungsten metal powders were made on samples taken across the width of the strip, and with various amounts of surface material removed, to determine if any preferred orientation existed. No preferred orientation was found in any of the samples examined.

The method used was a modification of the Schultz technique, using the Norelco Pole Figure Fixture, whose geometry and operation is described, in conjunction with the Norelco diffractometer.

Defocusing resulting during the run of a pole figure is discussed and a method for reducing this defocusing is described.

The …

A Method Of Estimating Groundwater Influx Into A Vertical Mine Shaft, Morris T. Worley

Masters Theses

"Prediction of groundwater influx into mine openings is one of the more important pre-development problems encountered in mining. A satisfactory method of estimation would provide the information necessary for a mining company to dewater prior to shaft sinking, pre-grout the shaft area, or plan pumping schemes to handle the expected flow.

A standardized field method of estimating groundwater supply from pumping test data was developed by O. V. Theis and others. In the present research problem, the estimation procedure has been simplified by the use of nomograms. Certain modifications in the estimate must be made when a pumping well is …