Digital Commons Network^™

The Effect Of Submerged Jets On The Hydraulic Jump, Harvey E. Jobson

Masters Theses

"Tests were performed in order to determine the effects of forcing submerged jets of water into the base of a hydraulic jump. The specific energy of the water leaving the hydraulic jump, the length and the wave formation properties of the jump which had been modified by the introduction of submerged jets were determined and compared with the same characteristics of a normal hydraulic jump and a hydraulic jump which had been modified by the use of baffle piers.

Test results indicate: (a) the quantity of water flowing through the submerged jets is a primary factor in determining the specific …

Transient Temperature Distribution In A Finite Cylinder And An Infinite Cylinder Subjected To Some Boundary Conditions, Harng-Sen Huang

Masters Theses

"This thesis is concerned with the theoretical heat transfer analysis of solid cylinders. The first problem considered is the transient temperature distribution in a finite cylinder. This cylinder has a uniform initial temperature and a uniform constant surrounding temperature. This case is solved by the separation of variables. Combining the charts for the infinite cylinder and the charts for the infinite plate one can determine the solution to this case easily. If a uniform constant surface temperature is prescribed instead of a surrounding temperature, the solution can be obtained from the previous one by charging the Nusselt number to infinity. …

The Development And Evaluation Of An Experimental Technique To Determine Stress Distribution In Uniformly Loaded Flat Plates, James William Walker

Masters Theses

"This thesis reports and evaluates an experimental technique that was developed to determine and monitor the stresses in a simply supported, uniformly loaded circular plate. Deflections are less than half the thickness of the plate. The application of the developed technique to plates whose integrity has been compromised with holes in various locations is discussed.

Resistance strain gages were used to determine experimentally the stresses in a simply supported, uniformly loaded circular plate with and without a concentric hole. The accuracy of the experimental results was established to be within approximately six percent of theoretical.

Proper application of the experimental …

Cylinder-Head Surface Temperature And Maximum Pressure In A Diesel Engine, Jayant M. Patel

Masters Theses

"This report presents the result of an experimental investigation on the effect of 1) fuel consumption in a diesel engine on the mean cylinder-head surface temperature 2) engine speed and load on the maximum cylinder pressure.

A fast-response thermocouple was fixed in the cylinder head and temperatures were measured for various load and speed conditions. An attempt was made to record a transient surface temperature versus crank-angle diagram. Some doubt as to the reliability of this recording may arise because of the very small amount of time lag in the thermocouple action. This is immaterial to the subject of this …

A Study Of Certain Conservative Sets For Parameters In The Linear Statistical Model, Roger Alan Chapin

Masters Theses

"In the case of the linear statistical model, it has been shown that under certain conditions the confidence intervals obtained by considering the parameters one at a time are conservative when used as a joint confidence region, using the product of confidences as the confidence. However, nothing had been known of how conservative they are. This research provides accurate estimates of the true confidence for these cases.

Also, it has not yet been proved that they are indeed conservative for all cases. It is thought that they are, and the results of this research support this conjecture"--Abstract, page ii.

The Construction Of A Single Crystal Neutron Diffraction Unit And Measurement Of Effective Neutron Temperature, Larry Dean Thompson

Masters Theses

"The continued expansion of the nuclear reactor facility and the nuclear engineering program makes it desirable that a neutron spectrometer be available at the reactor facility. This unit would be available for use in graduate and undergraduate laboratories and for graduate research.

A single crystal, white radiation spectrometer including collimator, automatic controls, and shielding was designed and constructed.

The performance of the unit was checked using LiF and Cu crystals. A rocking crystal curve and a θ - 2θ curve was obtained with each crystal. The effective neutron temperature was then determined from the LiF crystal θ - 2θ curve"--Abstract, …

The Elastic And Anelastic Constants Of A Synthetic Fluor-Mica Formed By Glass-Ceramic Fabrication Techniques, John H. Ainsworth

Masters Theses

"A tetrasilicic fluor mica, K₂Mg₅Si₈O₂₀F₄, was synthesized using glass forming techniques. Density changes, weight losses, and shrinkage, as well as elastic and anelastic properties, were measured on bars heat-treated at selected temperatures between 500°C and 1150°C to determine the characteristics of this material. Phase changes were followed by determining thermal expansion, logarithmic decrement, and modulus of elasticity from room temperature to 800°C.

It was found that the elastic and anelastic constants decreased gradually with heat treatments from 600°C to 1000°C. This indicated progressively increased structural ordering. Heat treatments above 1000°C …

The Transmission Of Loads To Point Bearing Piles In Sand Beneath Retaining Walls, Alan Albert Kamp

Masters Theses

"An experimental investigation was made of the way in which loads were transmitted to point bearing H-piles in sand under a retaining wall. Using a plastic model, the moments and axial loads were determined along the length of the pile by measuring the strains with electric strain gages. A comparison was made of the experimental results at the top of the pile and the analytical results at this point; the latter obtained from the common practice used in design. The comparison was very poor because the excessive horizontal load (that part of the horizontal load which could not be carried …

Analysis Of Continuous Folded Plate Roofs, Yung-Ping Wang

Masters Theses

"This work presents an analysis of continuous folded plate roofs considering the effects of relative joint displacements. For this analysis the normal modes of the lateral beam vibration were used as the form of the deflection curve and the loading was sinusoidal. By using symmetry and anti-symmetry, a possible method of analyzing prismatic folded plate roofs comprising one bay transversely but continuous over two or more spans longitudinally is suggested"--Abstract, page ii.

Thermal Degradation Of Poly (Methyl Methacrylate) In Solutions In A Closed System, Vikram Pranjivandas Parikh

Masters Theses

"A study has been made of the thermal degradation of poly (methyl methacrylate) of two different molecular weights, 2,303,000 and 43,000, in 1,2-dichloroethane in a closed system. The results indicated that the polymer having a molecular weight of 2,303,000 undergoes degradation while the low molecular weight polymer 43,000 undergoes reverse polymerization, and the molecular weight remains constant. The molecular weight of high molecular weight samples after 48 hours decreased from 2,303,000 to 2,232,000 and 1,690,400 at 50⁰C and at 98.5⁰C, respectively"--Abstract, page [i].

Model Study Of A Folded Plate Roof, Graham G. Sutherland

Masters Theses

"The purpose of this study was to conduct a model study of a folded plate roof in order to determine the feasability [sic] of using model studies as a method of design. Dimensional analysis was used to derive prediction equations for determining the stresses in two prototype structures, when the stresses in the model were known. One model and two prototype folded plate roofs were constructed of plexiglas [sic]. SR-4 strain gages were attached to the structures and strain readings taken as a uniform vertical load was applied in increments. From the strains the stresses at various points in the …

Optimum Finite Memory Nonlinear Filter, Ching-Chyoun Yang

Masters Theses

"This thesis investigates the possibility of using the Zadah theory and a machine type computer to design an optimum finite memory nonlinear filter for extraction of Poisson distributed signal pulses from a background of Gaussian noise. Basically the procedure involves the technique of solving simultaneous equations by the computer. We demonstrate that it is possible to find the limitation of the filter of class N₁ in terms of an absolute minimum mean square error. However, due to the capacity of the computer we do not actually determine the absolute minimum. Nevertheless we do show that the mean square error decreases …

An Instrument For The Measurement Of Anelastic Properties Of Glass, Thomas Frederick Miller

Masters Theses

"An inverted torsion pendulum for measuring the internal friction and dynamic shear modulus of glass fibers over an extended temperature range has been constructed and calibrated. The calibration consists of the determination of the moment of inertia. Extraneous damping losses were investigated and primary sources were found to be (1) the suspension thread, (2) the method of securing the fiber and (3) air damping. Anelastic measurements were made on an annealed vitreous silica fiber and a soda-lime-silica fiber"--Abstract, page ii.

Discharge Characteristics Of Side Weirs, Edgar Snowden

Masters Theses

"The purpose of this study is to investigate the division of flow of water in a flume of rectangular cross-section when the flume is provided with a side weir. An equation has been derived so that the quantity of water flowing over the side weir compared to the quantity of water flowing in the main channel can be predicted. This ratio is acceptable only within the ranges of heads, velocities, and weir lengths imposed by the geometry of the system tested"--Abstract, page ii.

A Study Of Hot Shortness In Steels, Koang-Hwa Kung

Masters Theses

"In this investigation an attempt was made to study the deformation of a number of laboratory-melted and commercial steels. A compressive load was applied to the steels at constant temperature and also during heating. The amounts and rates of deformation in these two types of tests was not consistent: in the constant temperature tests the hot short steels deformed more than the others while they appeared to deform less during heating. Metallographic examination of the sulfides indicated that the sulfides in cast steel are not stable and that they change during heating and hot working"--Introduction, page 2.

The Effect Of Copper Upon The Eutectoid Reaction In The Zinc-Aluminum System, Paul Theodore Corcoran

Masters Theses

"A Leitz dilatometer was used to study the kinetics of the eutectoid reaction in the zinc-aluminum system and the effect of small additions of copper upon this reaction. Three alloys were investigated: a pure 78% zinc - 22% aluminum alloy; a 78% zinc - 21.9% aluminum - 0.1% copper alloy; a 78% zinc - 21% aluminum -1.0% copper alloy. It was found that this reaction was similar to the pearlite reaction in the iron-carbon system. The reaction occurred by diffusion processes and the products of the reaction looked similar to pearlite when examined under the microscope. Copper was found to …

The Kinetics And Mechanisms Of The Reaction Of Benzyl Chloride With Potassium T̲-Butoxide In T̲-Butyl Alcohol, Der-Rong Chen

Masters Theses

"Benzyl chloride is a moderately reactive halide. Substitution of the Cl⁻ by other nucleophiles, e.g., HO⁻, AcO⁻, S₂O₃⁻, Br⁻ etc. proceeds almost quantitatively in solutions at convenient temperatures ... The object of this study was to investigate if the less basic t̲-butoxide in t̲-butyl alcohol would afford the same product, viz., stilbene; and, if so, by what mechanism. A study of the products and kinetics of the interaction between benzyl chloride and potassium t̲-butoxide in t̲-butyl alcohol therefore has been initiated"--Introduction, page 1.

A Measurement Of Dead Space And Its Effect On The Homogeneous Nucleation Rate Of Water Vapor In Helium, Michael A. Grayson

Masters Theses

"The existence of a "dead space" surrounding each nucleated water droplet is demonstrated and measurements of its rate of development are made. The effects of this "dead space" are considered to be due to both the removal of vapor from the helium-water vapor mixture and the evolution of heat about the drop due to its growth. The results confirm the usefulness of the concept of a "dead space" and provide a means for its measurement with respect to time. Recommendations for further study and a method of correcting for dead space effects is given"--page [i].

Thermal Degradation Of Poly (Methyl Methacrylate) In Solution In Various Solvents, Ya-Chih Chen

Masters Theses

"A study has been made of the thermal degradation of poly (methyl methacrylate) of different molecular weights in toluene, ethyl acetate and chloroform. Four poly (methyl methacrylate) samples having molecular weights of 2,210,000, 733,000, 320,000, and 43,00, respectively were studied in this investigation. The results indicated that the polymer having a molecular weight of 2,210,000 undergoes degradation while the low molecular weight polymers having molecular weights of 733,000, 320,000, 43,000 undergo reverse polymerization"--Abstract, page [ii].

The Effect Of Small Alloy Additions On The Quench Induced Texture Of Alpha Uranium, Kenneth Ray Riggs

Masters Theses

"The preferential orientations produced in binary alloys of U-Si and U-Cr on plane sections perpendicular to the direction of heat flow by cooling from beta-phase temperatures were determined. The experimentally determined textures were presented using inverse pole figures. A definite and reproducible relationship was found to exist between the preferred orientation present at any position and the cooling rate which material at the position had experienced. It was found that the concentration of the alloying elements within the ranges studied had little detectable effect upon the observed relationship between the cooling rate and the resulting preferential orientation. It was postulated …

Effects Of Internal Pressure Upon The Buckling Of Thin Circular Cylindrical Shells Under Axial Compression, Leroy E. Thompson

Masters Theses

"An experimental investigation was made of the effects of internal pressure upon the buckling of thin circular cylindrical shells under axial compression. A comparison was made of the experimental and theoretical results; the latter were derived from the large-deflection theory. Results showed that the internal pressure had an appreciable strengthening effect upon the buckling of the cylindrical shell. The comparison showed that the experimental results were lower than the theoretical results for a given internal pressure. The discrepancy between the results can be expected since there were factors not included in the theory: imperfections, end conditions, lengths, and material irregularities"--Abstract, …

The Separation Of Radioactive Technetium And Zirconium By Electrodialysis And A Study Of The Behavior Of Technetium In Aqueous Solutions, William Victor Andoe

Masters Theses

"The rapid increase in radioisotope applications necessitates improved technology for separation and purification of the fission product elements. Electrodialysis techniques employing Permutit anion exchange membrane(3148) were used to separate technetium from zirconium. The method was based upon the stability of the pertechnetate ion in alkaline solutions and the precipitation of zirconium from alkaline solutions. The separation of radiotechnetium and radiozirconium was effected with a two cell electrodialysis unit employing an anion exchange membrane. The solution medium consisted of fluoride and nitrate ions which were made basic with sodium hydroxide. The minimum basicity for a good separation was 0.1N NaOH"--Abstract, page …

Field Permeability Determination Of Partially Saturated Fine Grained Soil, Edward G. Rapp

Masters Theses

"The determination of water permeability through a soil is necessary to estimate seepage losses from small reservoirs. At the present time, the methods available to conduct this determination in partially saturated fine grained soils are expensive and in most cases not commensurate with the cost or importance of the individual structure. This investigation was conducted to evaluate the use of a proposed, potentially inexpensive field procedure in this situation. A modified borehole apparatus was utilized in field tests to determine the permeability of a partially saturated soil deposit in place. Undisturbed samples from the same location were tested in the …

Equivalent Circuit Of Unsymmetrical Inductance Diode Using Linvill Lumped Model, Donald Lawrence Willyard

Masters Theses

"Integrated circuit techniques and applications are rapidly changing the electronics industry. A problem common to both state-of-the-art approaches to integrated circuit fabrication is that of miniaturizing and integrating inductors. It is found that, for a certain range of injection current levels, certain unsymmetrically doped junction diodes have an inductive small-signal impedance. This thesis discusses the theory of inductance diodes and applies finite difference equations and the Linvill lumped model to the differential equations that describe their carrier flow processes. The static I-V characteristic and the small-signal equivalent circuit at high injection densities are derived. The elements (R,L,C) of this equivalent …

Permeability And Additive Absorption And Extraction In Lubricating Greases, Eugene Hsiung-Jen Tu

Masters Theses

"A permeability apparatus was used to measure the permeability coefficients of eight Lithium-Calcium greases and ten Baragel greases in which the viscosity and type of the oil component were varied. The oil present in each grease was used for its permeability measurement.

An improved sample packing technique was developed to improve the repeatability of permeability measurements. Repeatability of ± 3% was achieved. In general the permeability coefficients of the non-soap Baragel greases were higher than those of the lithium-calcium greases with comparable oil components, and those of greases containing paraffinic oils were higher than these containing naphthenic oils. The effect …

A Study Of The Photomechanical Effect In Silicon, Ronald M. Oglesbee

Masters Theses

"This paper presents the results of an experimental investigation into the photomechanical effect in silicon. The effect was found to be very similar to the electromechanical effect. In both cases the phenomena observed is the softening of a thin surface layer of the material when it is either illuminated or when a current is flowing through the material. An anisotropy was observed in both the hardness and the photomechanical effect. Increasing temperatures tended to "washout" the photomechanical effect. The surface hardness and the photomechanical effect were found to depend heavily on proper surface preparation of the samples, however little dependence …

Stability Determination By Liapunov's Method In Nonlinear Control Systems, Neng-Chung Liao

Masters Theses

"An introduction to Liapunov's second method as it applies to control system stability is presented in this work. Main theorems and definitions of Liapunov's method are treated. In particular, Lur'e's method and Szego's method for testing the stability of a nonlinear system are presented, and several examples are used to illustrate these procedures"--Abstract, page ii.

Use Of Spent Sulphite Liquor For Stabilization Of Fractured Rock And Sealing Off Water Bearing Formations, Laxman Singh Sunda

Masters Theses

"The paper industry, in its process of manufacturing pulp from wood, produces large quantities of a substance called lignin, lignin sulphite, or lignosulphonate. This material has been disposed of as a waste product; however, it does have many potential uses. In this investigation, lignosulfonates were used as agents for bonding rock sections together and, as the chief component of gels, for filling the pores of artificial rock cores. The purposes of these tests were to find how this substance could be used in the mining industry, for stabilizing fractured ground around mine openings and for sealing off water influx into …

Effect Of Calcium Lignosulfonate On Properties Of Concrete At Early Ages, Lawrence Kong-Pu Wang

Masters Theses

"The objective of this investigation was to determine the effects of calcium lignosulfonate on the physical properties of concrete. Calcium lignosulfonate used as an admixture was tested for its effect on the tensile and compressive strength of plain concrete cylinders, and for its effect on the flexural strength of plain concrete beams. The effect of the admixture on shrinkage, slump, air content and unit weight was also studied. the test results showed that calcium lignosulfonate reduces the amount of water required to make a workable concrete mix; a more workable mix saves money because it is easier to place, thus …

Solid Solubility Of Sulfur, Selenium, And Tellurium In Molybdenum At 1100°C, Lattice Constants Thermal Expansion Coefficients, And Densities Of Molybdenum And The Molybdenum-Base Alloys, Ramesh Purushottamdas Shodhan

Masters Theses

"With the ever increasing requirement for engineering materials having adequate mechanical properties at ever higher temperatures there has been, in quite recent years, a considerable increase in the study of molybdenum and molybdenum-rich alloys. Since 1945 extensive information on the engineering properties of molybdenum and molybdenum-base alloys has gradually become more available ... The present work involves the determination of solid solubility of elements with large atoms such as sulfur, selenium, and tellurium in molybdenum at 1100°C using the parametric method. Furthermore, the thermal expansion coefficients of pure molybdenum and of molybdenum-base solid solutions containing the elements just mentioned were …