Digital Commons Network^™

Modification Of The Hydraulic Jump By Submerged Jets, Edward Leon Tharp

Masters Theses

"Tests were performed in order to determine the effect of submerged jets injecting water into the base of the hydraulic jump. The jump was studied in terms of the following properties: specific energy of the flow leaving the hydraulic jump, length of the hydraulic jump, tailwater depth, and wave formation properties. These properties for the hydraulic jump with submerged jets were compared to the natural hydraulic jump.

Results of the tests indicate that: submerged jets at any angle tested tend to decrease the specific energy of the water leaving the jump and are more effective than the impulse-momentum principle indicates, …

Minimum Cost Data Collection Techniques For Circulation Control At The University Of Missouri At Rolla Library, John Peter Shewchuk Sr.

Masters Theses

"Data collection is beginning to assume increased importance in the field of data processing. This thesis investigates a method for quantitatively selecting a portion of the library to place on an automated circulation control system that uses data collection as an entry into a data processing system.

The circulation function of the library was considered to be an inventory problem. Titles were considered as items of inventory and circulation of that title was considered to be a "sale" of that item. The IMPACT method was used to distribute items (titles) in a sample by age. Various ages were found to …

Analysis Of Sand Asphalt Mixtures, Maurice A. Sayegh

Masters Theses

"The objective or this investigation was to determine the optimum percent of asphalt which should be added to the sand asphalt mixture. Also the effects of filler on the properties or the sand-asphalt mixture were evaluated.

The variables in this study were mineral filler, asphalt cement, and asphalt content. The sand used in this study was sub-rounded, and uniformly graded. The asphalt was asphalt cement with two different penetrations, one of 85-100 penetration grade and the other of 120-150 penetration grade.

Three different groups of mixtures of sand-asphalt were prepared. The first group consisted of adding 85-100 penetration asphalt to …

A Crystallographic Study Of The Pbzro₃-Pbtio₃-Bifeo₃ Ternary System., Dannie R. Clarida

Masters Theses

"The purpose of this investigation was to conduct a crystallographic study of the PbZrO₃-PbTiO₃-BiFeO₃ ternary system, where all three components are perovskites. Lead zirconate is antiferroelectric, lead titanate is ferroelectric, and bismuth ferrate is thought to be ferroelectric. X-ray diffraction analysis was employed to determine the crystallographic structure and lattice parameters.

A tetragonal region was found to exist in the area of high PbTiO₃ content. A rhombohedral region occurred in the remainder of the system with high BiFeO₃ and PbZrO₃ content, except for an orthorhombic envelope along the PbZrO₃-BiFeO₃ side of the diagram up to approximately 70 per cent BiFeO₃.The …

A Study Of Modified Plug Designs For A Globe Valve, Robert W. Wagner

Masters Theses

"This thesis presents an empirical study of the characteristics of a cylindrical skirted disk valve used as a flow regulating device. Holes were drilled in two separate removable cylinders, which, when respectively attached to the valve plug adapter, provided control of the flow rate. These cylinders could be moved to permit exposure of more or less flow area by means of the valve stem and crank mechanism. At the closed position of the valve no holes were available for flow within the differential pressure zone of the valve, while at the full-open position all the drilled holes were within the …

Stable Predictor-Corrector Methods For First Order Ordinary Differential Equations, Terrell Lester Carlson

Masters Theses

"Because of the wide variety of differential equations, there seems to be no numerical method which will affect the solution best for all problems. Predictor-corrector methods have been developed which utilize more ordinates in the predictor and corrector equations in the search for a better method.

These methods are compared for stability and convergence with the well known methods of Milne, Adams, and Hamming"--Abstract, page ii.

The Development Of A Modified Soil Shear Vane, Vernelle Truman Smith

Masters Theses

"The purpose of this investigation was to determine how the soil shear graph could be modified to measure more accurately values of shear strength of fine-grained, cohesive soils. Several modifications were tried, however, the one that gave the most satisfactory results consisted of a vane and base plate mechanism.

A red clay of high plasticity obtained from a local cave was tested in both the natural or undisturbed state and in the remolded state. The only variable was the moisture content. Compaction effort was the same for all remolded specimens. Tests were conducted on undisturbed samples taken with thin walled …

An Investigation Of Consolidation On Compacted Partially Saturated Clarksville Soil, Ma-Tai Matthew Chen

Masters Theses

"The Terzaghi theory of consolidation and the assumption of his theory, pore pressure and effective stress, secondary compression and rheology were all reviewed and discussed. Eight compacted unsaturated samples made from Clarksville silty clay (CL) under different compaction efforts and moisture contents were subjected to consolidation load increments. Each load increment was maintained for 24 hours. An extra compacted sample was loaded for one month to investigate secondary compression.

From e-p curves, five settlement vs. compacted embankment height curves were derived for different compaction effort and moisture contents. These curves may be of practical use, when checked by field measurements …

Kinetics And Mechanisms Of Base-Catalysed Reactions, Rohit Panalal Sheth

Masters Theses

"Base-catalysed reactions normally involve complex series of transformations. their kinetics is usually governed by a variety of equilibria, participating in the overall and concurrent processes as well as by competitive side-reactions that interfere with the normal course of such reactions. Mechanisms which have been proposed, by and large, are primarily based on product, by-product and intermediate analyses together with some scattered kinetic and isotopic evidence. In the cases where kinetic studies have been attempted, highly complex mechanisms have usually been proposed due to the frequent necessity of using heterogeneous media or employing involved mathematical treatments to describe the kinetics of …

Mass Transfer In Droplets With Turbulent Internal Circulation - Mathematical Description, Jayantilal Mohanbhai Patel

Masters Theses

"This investigation was carried out to check the accuracy of the eigenvalues, λ_n, calculated by Wellek and Skelland, using some method other than the Rayleigh-Ritz technique and also, to determine the coefficients, B_n in series solution, which were not calculated before.
The eigenvalues were obtained by trial and error procedure using the standard Runge-Kutta method. The coefficients B_n were obtained by using eigenvalues. By using this information the fractional extraction was calculated as a function of droplet contact time.

The Wellek-Skelland modification was also solved by finite difference technique to compute fraction extracted as a function …

Nucleate Boiling Heat Transfer To Liquid Nitrogen At Atmospheric Pressure, Satish R. Parikh

Masters Theses

"The object of this investigation was to study the effect of micro-roughness, a thin layer of oil, and infra-red radiations on the cylindrical heat transfer surface of copper, in liquid nitrogen and at atmospheric pressure during nucleate boiling. An attempt was made to find any possible effect of orientation of the heat transfer element on nucleate boiling. A number of different runs were taken with different degrees of roughness, and different orientation positions. Nucleate boiling has been found to be nearly independent of the heat transfer surface roughness and of orientation while strongly dependent on the chemical nature of the …

An Ac Method Of Measuring The Conductivity Of Dielectric Liquids., Henry E. Fischer

Masters Theses

"The problem undertaken in this thesis is the presentation of a method of measuring the conductivity of dielectric liquids in which the liquid is used as the parallel tank circuit of a modified Wien-bridge oscillator. The main advantage of this method is that the frequency of the voltage applied to the liquid can be varied by simply varying the oscillator frequency. This allows the selection of a frequency which is best suited to the liquid in regard to polarization and relaxation time.

An oscillator was designed, built and used in the laboratory to measure the conductivity of the dielectric liquids …

Analysis Of Time-Varying Linear Multipole Filters With Sampled Nonstationary Random Inputs, Ming-Chwan Chow

Masters Theses

"In this thesis an analytical method is developed to determine an optimum time-varying linear filter in order to satisfy the following specifications. The filters are of sampled data multipole form with n inputs and m outputs. The signal of each input is a member of a nonstationary random process, and the signal is corrupted by stationary noise.

The statistical optimization theory developed by Wiener is extended to a linear time- varying filter with nonstationary input. Correlation functions are defined for nonstationary ensembles. The mean- square error is calculated in terms of these correlation functions. By minimization of the mean-square error, …

An Application Of The Variable Gradient Method Of Generating Liapunov Functions To Discrete Systems, Henry N. Peterson

Masters Theses

"The variable gradient method of generating Liapunov functions has been used only for continuous systems. This thesis presents an application of the variable gradient method to non-linear sampled data control systems.
Certain modifications to the variable gradient method are developed and several examples are presented which demonstrate the application. An attempt was made to synthesize the control system parameters, but due to the complexity of the ΔV functions, the synthesis in general cannot easily be obtained . To circumvent the problem of determining if the ΔV functions are negative definite, a set of computer programs were written to determine a …

Study Of Heat And Mass Transfer Through Non-Wettable Porous Membrane, Rajender Kumar Rohatgi

Masters Theses

"The object of this investigation was to study the use of non-wettable porous membranes for simultaneous heat transfer and mass transfer of water from a hot salt solution stream to a cold distilled water stream, the streams being in countercurrent flow separated by the membrane. This type of mass transfer was achieved in the experiments, and mass and heat transfer coefficients were measured.

The membranes studied in this work were made of fiberglas treated with Teflon dispersion and aluminum sulphate. The fiberglas membranes yielded desired results. Empirical correlations were proposed which predict values of heat and mass transfer coefficients close …

The Missouri Miner, November 12, 1965

The Missouri Miner Newspaper

No abstract provided.

The Missouri Miner, October 01, 1965

The Missouri Miner Newspaper

No abstract provided.

The Performance Of Beams And Columns Continuously Braced With Diaphragms - I, Gordon P. Fisher, S. J. Errera

CCFSS Library (1939 - present)

When properly attached, shear-rigid light-gage metal diaphragms, such as roof decking or wall sheathing, can be very effective as lateral bracing for slender columns and beams. At present, limited design use is made of this fact, because of inadequate information on the effectiveness and reliability of such bracing. In this thesis, previous theory on the stability of Isection beams and columns braced with shear-rigid diaphragms has been extended. Two energy methods are used, one employing the Euler-Lagrange conditions from the calculus of variations, and the other the Rayleigh-Ritz method. The problem initially considered is that of an I-section beam-column eccentrically …

The Missouri Miner, September 17, 1965

The Missouri Miner Newspaper

No abstract provided.

Structural Performance Of Light Gage Steel Diaphragms, Larry D. Luttrell, George Winter

CCFSS Library (1939 - present)

Light gage steel roof, wall, and floor systems may be used to transfer in-plane shear forces from one part of a framed structure to another, leading to reduced loads in parts of the structure. This is particularly noticeable in buildings having rigid end walls and under lateral loading. The diaphragms transfer forces from the interior frames into the foundation through the rigid end walls, resulting in lower loads for the interior frames. The amount of force transfer is dependent upon the in-plane shear strength and is particularly sensitive to the shear stiffness of the diaphragm. The results from some 60 …

Effects Of Cold-Forming On Light-Gage Steel Members, Kenneth W. Karren, George Winter

CCFSS Library (1939 - present)

Cold-forming may cause significant increases in tensile and in compressive yield strength in both the corner and flat elements of light-gage cold-formed steel members. The cumulative effects may raise the yield strength to as reuch as 70% above the virgin yield strength of the as-rolled sheet steel. The yield strength of corners is always considerably higher than that of any other portion of a cold-formed member because of the large plastic deformations which take place in the corners. Thus compact members with a large ratio of corner area to cross sectional area will have the largest increases in yield strength. …

The Missouri Miner, May 07, 1965

The Missouri Miner Newspaper

No abstract provided.

The Missouri Miner, February 12, 1965

The Missouri Miner Newspaper

No abstract provided.

Studies On The Conversion Of Indole Acetic Acid And Oxindole Acetic Acid By Hygrophorous Conicus, Barbara Ruth Patterson

Masters Theses

"The fungus, Hygrophorous conicus, produces the enzyme, indole acetic acid oxidase, when grown in the presence of indole acetic acid (IAA) or tryptamine. The IAA acts both as an inducer and a substrate for this intracellular enzyme. The product of the oxidation catalyzed by the IAA oxidase is oxindole acetic acid (OIAA). Since the IAA and OIAA absorb maximally at two different wavelengths the use of spectrophotometric analysis was possible for assaying for the IAA oxidase activity. Paper chromatography was used for qualitative identification of the IAA and OIAA. The rate of growth and the rate of formation of the …

Design Of A Photoelectric Transient Torque And Speed Meter, Raojibhai A. Patel

Masters Theses

"There are many situations in which it is desirable to know the speed of the shaft and the torque it is transmitting, when it is equally undesirable to make any mechanical connection to the shaft. This thesis describes the development and design of a device for measuring the torque and speed by photo-electric means. The basic principle is that a light beam parallel to the shaft may be used to pick up the desired information without adding friction to the system. The deflection of a torque tube inserted in the shaft opens or closes a set of apertures arranged in …

Comparison Of Methods To Select A Probability Model, Howard Lyndal Colburn

Masters Theses

"A comparison is made between the estimates of the parameters in a gamma distribution obtained by the method of moments with those obtained by a numerical approximation to the maximum likelihood estimates. The estimates obtained by the numerical approximation had a smaller mean squared error from the true value than the estimates obtained by the method of moments. Modifications to tests of fit are made in order to develop methods to select a distribution from a set of possible distributions for a population with an unknown distribution. These selection methods are compared in their ability to make correct selections. Although …

Determination Of The Temperature Distribution Of The Ionized Portion Of The Jet From A Vortex Stabilized Plasma Generator Operating On Argon, G. Douglas Schellman

Masters Theses

"The interim thesis deals with the determination of the temperature distribution of a plasma jet operating on argon. It is the purpose of this thesis to present in detail the experimental process used and make a correlation of the experimental and theoretical results.

A copper enclosure was placed around the protruding flame, and the embedded thermocouple readings were taken and recorded. A stagnation temperature probe was inserted in the enclosure and moved both axially and transversely toward the flame taking readings at each pre-chosen interval. The exit temperature of the jet was obtained from a total energy balance.

From the …

Turbulence In Journal Bearings, Kashyap R. Mehta

Masters Theses

"In this investigation, an experimental study was performed on a journal bearing under laminar and turbulent flow conditions. Using relationships for friction factor developed previously by other investigators a comparison was made with results of this present investigation. Since the flow changes from laminar to turbulent with a change in speed of rotation, curves for friction factor as a function of speed were plotted. Various attempts to make the recording and measuring systems more sensitive were also made and are discussed in this thesis"--Abstract, page ii.

A Photoelastic Study Of The Effect Of Certain Geometric Variables On The Plane Stress Distribution In An Electrical Insulator Body, Richard L. Pendleton

Masters Theses

"Photoelastic models were used to indicate stress patterns in various geometrically designed shapes. Each model represented a two-dimensional cross-section of the interior portion of an axially symmetrical porcelain electrical insulator. Five different loading pins were combined with three loading heads to produce eleven models. The maximum stress in each model was determined using a photoelastic method of stress analysis. An attempt was made to select the best structural design to be used in an electrical insulator. The test results indicate that the most desirable stress distribution is obtained using a single step loading pin and that the loading head angle …

Internal Friction Of Mixed-Alkali Silicate Glasses, James E. Shelby

Doctoral Dissertations

"The mixed alkali effect in silicate glasses was examined from internal friction measurements made over the temperature range from -190 to 500⁰C and at a frequency of 0.4 Hz. Supplemental measurements of the activation energy for the different internal friction peaks, dynamic shear modulus, density, and index of refraction were also made. All measurements were confined to silicate glasses containing mixtures of Li-Na, Li-K, Li-Rb, Li-Cs, Na-K, Na-Rb, Na-Cs, and K-Rb. Rötger's interpretation of the internal friction of mixed-alkali silicate glasses is shown to be incorrect. A previously unreported internal friction peak was observed whenever two different alkali oxides were …