Digital Commons Network^™

The Effect Of Nickel On Activated Sludge, James Robert Matthews

Masters Theses

"The primary objective of this investigation was to determine the effect of nickel on activated sludge over a comprehensive range of concentrations and to evaluate the ability of the sludge to acclimate and become more tolerant to the metal. Six one-liter fill and draw activated sludge units were fed domestic sewage; five of these units also received constant, increasing, and shock doses of nickel while the sixth was maintained as a control. Treatment efficiency was evaluated in terms of the chemical oxygen demand, suspended solids, and nickel content of the effluent. A Warburg respirometer was also employed and was operated …

Detection Of Stress Corrosion Cracking In U-Bend Brass Specimens By An Electro-Mechanical Method, Floyd Elwin Loftin

Masters Theses

"An apparatus was designed and built which held two u-bend specimens. When the specimens were exposed to a corrodent, losses in strength were detected as a result of stress corrosion cracking. The apparatus was used to study time to failure of cartridge brass u-bend specimens exposed to ammoniacal copper sulfate solutions which varied in pH. A minimum time to failure, 1.06 hours, was detected at pH 7.2. The maximum time to failure, for the range studied, was 28.36 hours at pH 7.7.

No useful data were obtained in the range from pH 6.6 - 6.8. thick, black surface coatings were …

The Effect Of Cadmium On Anaerobic Digestion, Lyle Lynn Pruitt

Masters Theses

"The main purpose of this study was to determine the effect of cadmium on anaerobic digestion. Metal concentrations in the form of regular and slug doses were considered. The possibility of acclimating anaerobic bacteria to higher cadmium levels was studied, and attempts were made to reestablish digestive action through re-seeding in digesters overcome by high cadmium concentrations"--Abstract, page [ii].

Thin Film Resistor Deposition, Rollie R. Herzog

Masters Theses

"Thin film techniques may be the key to future miniaturization of electrical equipment. The purpose of this thesis was to develop procedures for deposition of thin film resistors and to test these deposited resistors. Starting with a vacuum system, equipment was designed and built to hold and heat the substrate, monitor the substrate temperature and deposited resistance, and to evaporate the material to be deposited. Resistors were deposited and tested for resistance between resistors, capacitance between resistors, and resistance of resistors. A heat aging test was also used comparing resistors with and without a silicon monoxide coating"--Abstract, page ii.

The Design Of A Sensitive Probe For Mass Flux Measurements Of Water Vapor In Air, Devendra Vaikunthlal Mehta

Masters Theses

"This investigation pertains to the construction and investigation of a sensitive probe to determine the possibility of measuring the mass flux of water vapor in air under non-flow steady state conditions. The probe was a small electrolysis cell is which the electrolyte (partially hydrated phosphorus pentoxide) was used as the sensing element. The rate of mass transfer was determined by measuring the amount of direct current flowing through the acid film"--Abstract, page i.

A Second Study Of Homogeneous Nucleation Of Water Vapor In Helium, Raymond J. Schmitt

Masters Theses

"Absolute homogeneous nucleation rates in a supersaturated mixture of water vapor and helium are measured using a long sensitive time expansion chamber and a method devised by Kassner and Allard. A pulse technique is employed to produce the nucleation in an effort to suppress disturbing influences of vapor depletion and droplet growth. The time-varying nature of the supersaturation during the nucleation pulse is taken into account by an Integration over the pulse. Observed and theoretically predicted droplet concentrations are related by an assumed nucleation rate law which is adjusted until the total droplet populations predicted by integration of the assumed …

An Investigation Of Current Induced Mass Migration In Solid Metals, Steven Mitchell Kovel

Doctoral Dissertations

"In this investigation of current induced mass transport, the general phenomenological equations will be considered first so as to present a picture of the experimental situation. The theoretical computations are then divided into four sections: (1) the determination of the force on a defect due to electron scattering, (2) a discussion of how the force on the defect might be shared by the surrounding ions, (3) how an external force affects the diffusion frequency of an ion, and (4) what the rate of mass transport is under the influence of an electric field. So as to simplify the discussion and …

Pair Distribution For A Cell-Model Liquid, James M. Phillips

Doctoral Dissertations

"The pair distribution function for a cell-model liquid has been derived by Lund in the form of an integral equation which depends upon the cell-center distribution function and the cell model. From this integral equation an approximate integral equation is obtained by substituting a function, which is linearly dependent upon the molecular pair distribution function and a variable parameter for the cell-center distribution function. This approximate integral equation is solved for the molecular pair distribution and the variable parameter is shown to depend upon the difference between temperature and the critical temperature. Although the exact numerical solution of the molecular …

The Microbial Hydrolysis Of Cellulose And Some Factors Affecting The Production Of Cellulase In A Submerged Culture Of Alternaria Sp, Robert Murray Logan

Doctoral Dissertations

"A mile hydrolyzing procedure was utilized to degrade oak sawdust. Its capability of producing a suitable fermentatation [sic] medium was studied. In the interest of solubilizing, enzymatically, the carbohydrate portion of oak sawdust, an investigation was conducted in which various microorganisms were examined for their ability to utilize different forms of cellulose for their growth and to produce cellulose decomposing enzymes. The microorganisms included a myxobacterium, several fungi, and a wood-rotting basidiomycete. The fungi included two highly cellulolytic organisms, Myrothecium verrucaria and Trichoderma viride. The myxobacterium used was Sorangium cellulosum and the basidiomycete was Pleurotus ostreatus. The principla substrates employed …

Drag Reduction In Newtonian Polymer Solutions, Harry C. Hershey

Doctoral Dissertations

"Prior work in the area of drag reduction has been mainly limited to aqueous solutions. Theoretical and empirical analyses of the resulting data in aqueous solutions have been hindered by the fact that some polymers cause drag reduction and others do not...This investigation was directed to the study of how the size and configuration of the polymer molecule in solution affected drag reduction and the related phenomenon of turbulence suppression. Apparatuses were designed and built to measure viscometric flow, curves, friction factors, velocity profiles, and normal stresses (by a jet thrust technique developed by Metzner and associates)"--Summary, page 1-2.

A Study Of Near Surface Elastic-Anelastic Layers, Charles Allen Aldrich

Doctoral Dissertations

"Wave propagation through layered media is of importance in many disciplines. The near surface layers are of special significance, in that most measurements of waves are made within these layers. The purpose of this investigation was to formulate mathematical models with which to analyze the effects of near surface layering"--Introduction, page 1.

The Effect Of Varying Sea Coal Fineness On Sea Coal Activity In Molding Sands, Laurence A. Cooley

Masters Theses

"An experiment was conducted in an attempt to establish a relation between sea coal activity in a facing sand and the particle size of the sea coal added to the sand. It was felt that if a sufficient difference in distribution of volatiles was detected, a correlation between particle size and activity of the sea coal within the test specimens might be established. The lack of positive evidence to support such a relationship is indicative that a variation in particle size does not promote volatile re-deposition within the range of particle sizes investigated for the particular weight per cent of …

The Eccentric Orifice As A Flow Measuring Device In Small Diameter Pipes, James E. Casale

Masters Theses

"This thesis reports and evaluates the use of an eccentrically placed orifice as a flow measuring device in small pipe sizes. The orifice is placed in a concentric location and moved to increasingly eccentric locations until full eccentricity is reached. At full eccentricity the circumference of the orifice is tangent to the circumference of the pipe. The effects of increasing eccentricity are evaluated for four orifices...Flow coefficients for the orifices in different locations are plotted against Reynolds numbers. The eccentric orifice is a reliable, accurate flow measuring device for metering or controlling the flow of fluids. Design criteria can be …

Maximum Present Value Calculations With Digital Computers, James Boyd Robison

Masters Theses

"This paper discusses maximum present value calculations for a mineral property using digital computers. A semi-quantitative mathematical model to optimize operating conditions is considered. The model is based on a modified cash flow analysis. Many variables affect the solution, and their effect upon present value is described. Selected data (mining rate, costs, reserves, metal sales price, and others) for a hypothetical open pit copper mine are used in a set of solutions for present value. The results are discussed in detail. It is concluded that: (1) Digital computer methods are rapid and useful, (2) Changes in the mining rate, average …

A Graphical Method Of Estimating Heat Capacities Of Hydrocarbons, Pu-Ying Liu

Masters Theses

"Heat capacity arises because the individual particles comprising a substance are able to move and thus take up kinetic energy and usually also potential energy as the temperature rises. In many substances electrons do not absorb energy until very high temperatures are reached. Thus most heat capacity effects are interpreted in terms of the motion of the atoms neglecting electronic transitions. The total internal energy of a material is, therefore, equal to the sum of the energies due to translational and rotational motion of the molecules and to the vibrational motion of the atoms making up the molecules...The objective of …

Finite Difference Solution For Triangular Plates, Hao-Yang Huang

Masters Theses

"In this thesis the finite difference method is used to solve triangular plates with uniformly distributed transverse load. As a matter of convenience triangular coordinates are used. The supporting conditions as well as the shape of plate are varied. All calculations are performed by digital computer. The patterns of differential operators in triangular coordinates, the deflections of plates, and the moment distributions are shown and discussed. The results obtained for some special cases are compared with published solutions"--Abstract, page i.

Measurement Of Stray Load Loss Of D.C. Machines, Kanaiyalal Ramanlal Shah

Masters Theses

"For many years the standard practice, in calculation of conventional efficiency of d.c. machines, has been to include stray load losses as equal to 1% of the output. This assumption may be true for large, compensated d.c. machines but it is known to be small for smaller, uncompensated, general-purpose, industrial-type machines of open design. An A.I.E.E. Committee on Rotating Machines was formed to investigate whether the present practice of assigning 1% for the stray load loss is justified or not. They reached a conclusion, reported in 1949, after investigating 243 stray loss tests on different motors ranging from 1/2 hp …

Drop Growth In A Supersaturated Vapor, Roger Buecher

Masters Theses

"Using kinetic theory and the thermodynamics of phase transitions, a method is derived for finding the growth rate and temperature increase of a droplet in water vapor which has been supersaturated by the expansion of a cloud chamber. Calculations are performed for a specific numerical example and compared to other work in this field"--Abstract, page [2].

Taxonomic Study Of Fossil And Recent Otoliths Of Certain Cuskeels, Gary Neal Pointer

Masters Theses

"Otoliths are calcareous structures occurring in the auditory labyrinths of teleost (bony) fishes. Three pairs of these earstones normally are found: the sagitta, in the sacculus; the asteriscus, in the lagena; and the lapillus in the utriculus. In fishes other than the Order cypriniformes (carp, catfishes, and related forms), the sagitta is the largest otolith, and it may be used in taxonomic and other studies. Fossil earstones of cuskeels (Family Ophidiiae-Brotulidae), constituting the Preophidion complex, occur in relative abundance at various levels in the Claiborne, Jackson, and Vicksburg groups of the Lower Tertiary on the Gulf Coast. The present study …

Temperature Distribution In Thermal Boundary Layers (In Free Convection) Using A Modified Schlieren Method, Philip Ling Chen

Masters Theses

"A simple optical apparatus, the Schlieren interferometer, was constructed for the quantitative investigation of free convection heat transfer from solid bodies. The photographic results, checked by using thermocouples, were used in evaluating the temperature distribution, the key to the solution of these problems. Interpretation of the photographic results was made using the simple calculation for the conventional interferogram and the Dale-Gladstone law. Although the experiments were limited to a heated flat plate and a heated wire, two dimensional test pieces of irregular configuration can be investigated by the same apparatus with simple modifications. The photographs of the conventional Schlieren, the …

Construction Of A Capillary Viscometer And The Study Of Non-Newtonian Liquids, Hsun Kuang Yang

Masters Theses

"A capillary tube viscometer was built for the purpose of investigating the fluid properties of non-Newtonian aqueous CMC and Carbopol solutions. The viscometer was tested with Newtonian liquids (glycerine, water and two different oils) having known viscosities to insure that the viscometer was operating correctly. The shear stress-shear rate data obtained for different concentrations of CMC and Carbopol solutions were correlated using the simple power law model. The power law constants were only slightly affected by saturating the solution with iodine and carbon tetrachloride. Aging had very little effect on the viscosities of the CMC solutions but had a considerable …

Application Of The Photoelastic Coating Method To Evaluate The Stress Distribution On The External Surface Of The Cap Of An Electrical Insulator, Harijeetsinh Jagtiani

Masters Theses

"The Photoelastic Coating Method was applied to find the surface stresses on the cap of an electrical insulator. The strain distribution was observed and photographed. This color photograph indicated a visible geography of the maximum shear strain distribution in the region of the insulator where the birefringent plastic was bonded with a reflective cement. The Oblique Incidence technique was used to determine the principal stresses from the maximum shear strain (or the principal strain difference) readings, obtained from Normal Incidence. The critical cross-section of the insulator head was optically located, giving an initiative for the re-design of the insulator cap. …

Operating Characteristics Of A Cloud Chamber Suited For Condensation Measurements, Donald L. Packwood

Masters Theses

"It is the main purpose of this research to investigate the validity of using the adiabatic laws to determine the temperature from the pressure ratio. Some of the effects which might invalidate the use of the adiabatic laws will be studied. Special consideration will be given to the accurate calculation of [gamma]. Carstens' approximate calculation of the heat flow into the chamber due to conduction will be checked. A measurement will be made of how long the chamber remains adiabatic after an expansion when the continuing expansion technique is used. The static temperature gradient throughout the chamber will be measured …

A Study Of Re-Evaporation Nuclei, Ronald Dawbarn

Masters Theses

"Classical considerations of the evaporation of a homogeneously nucleated droplet in an atmosphere of low humidity, indicates complete evaporation of the drop. Experimental results however, show that there is left behind a residual nucleus that is quite stable. Condensation occurs on these nuclei at comparatively low supersaturations. Using a specially instrumented cloud chamber, experimental procedures are described which attempt to investigate some of the properties of these nuclei. Various possibilities causing this stability are examined and compared to the experimental results obtained"--page [ii].

Instrumentation Of A Diesel Engine For Measuring Cylinder Head Temperature, And Pressure At Various Crank Angles, Raman A. Patel

Masters Theses

"In this investigation, an attempt has been made to measure the instantaneous pressures in the cylinder and the transient temperatures of cylinder head versus crank angle in a Diesel engine. A strain-gage pressure transducer and a sensitive surface thermocouple were used. The pressure transducer was practically free from temperature influence and strain effects caused by installation. It had a greatly reduced sensitivity to vibrations compared with other available types of pressure transducers. The thermocouple had a very short response time. A device enabling very accurate measurement of crank-angle was constructed. Appropriate quantities were displayed on the screen of an oscilloscope …

Study Of Deformation Of Non-Oscillating Droplets In Liquid Media, Arun Kumar Agrawal

Masters Theses

"The object of this investigation was to find a method for predicting the deformation of non-oscillating liquid droplets which are moving in liquid media, from a knowledge of droplet size and the physical properties of the continuous and dispersed phase systems. The deformation of thirteen liquid-liquid systems was experimentally studied in this investigation"--Abstract, page i.

Free Convection Heat Transfer From An Inclined Heated Flat Plate In Air, Shu Chien Yung

Masters Theses

"An experimental investigation has been performed to determine the free convection heat transfer from a heated flat plate in air moved from the vertical position through three inclined positions to the horizontal position. The hot surface of the plate was facing downward for the horizontal and three inclined positions. Tests were performed at plate surface temperatures from 120°F up to 404°F. Data for the plate surface temperature at about 165°F with the plate in the vertical position agrees very well with previous experimental work. This same data was used to determine a new parameter, introduced into the Pholhausen free convection …

An Apparatus To Measure Capillary Jet Thrusts And The Evaluation Of Normal Stresses In Fluids, Charles Donald Green

Masters Theses

"The purpose of this work was to design, construct and calibrate simple, inexpensive apparatus which could be used to measure the normal stresses and tangential shear stresses of a fluid. For normal stress measurements, the capillary jet thrust principle was selected. A standard analytical balance was modified so that capillary tubes could be fitted on it horizontally. It was designed so that the thrust produced by a jet of fluid from the tube caused a deviation from the zero balance position. The weights needed to rezero the balance gave a measure of the thrust"--Summary, page 1.

Order-Disorder In Fe₃Al At Various Temperatures Induced By Neutron Irradiation, Robert F. Toma Jr.

Masters Theses

"Resistivity measurements were made on ordered and disordered Fe₃Al samples while irradiated by neutrons.

In the ordered as well as the disorder state, the different Fe₃Al samples were heated to 100, 150, 200, 250, and 300°C respectively, and were irradiated by a fast neutron flux of 0.534 x 10¹⁰ neutrons/cm²-sec. The ordered Fe₃Al measurements were characterized by an increase in resistivity denoting an advancement toward disorder. The disordered Fe₃Al measurements were characterized by a decrease in resistivity denoting an advancement toward order. In the Fe₃Al ordered and disordered samples …

The Shear Graph And Cohesive Soil, Charles Rees Nickerson

Masters Theses

"Some existing test procedures for measuring shearing properties of soils are reviewed. the correlation between the shear strength of two fine-grained soils as indicated by the unconfined compression test and the shear graph test is investigated. This is accomplished by comparing the test results at varying moisture contents and dry densities. One of the soils used is a red plastic clay, the other a silty clay. The test results indicate that for soils wet of optimum the shear graph strength can be taken as being equal to the unconfined compressive strength. This will be conservative for soils that exhibit an …