Digital Commons Network^™

Transpiration Cooling Of A Plane Porous Plate, Raymond George Posgay

Masters Theses

"The transient temperatures were determined in a porous plate for one dimensional heat flow and one dimensional counter coolant flow. One surface of the porous plate was heated by a hot gas by convective heat transfer. A general discussion of the problem is considered and the procedure described for working all such problems dealing with transpiration cooling.

The solution of such problems is illustrated by two examples employing a ceramic plate one inch thick and cooled by a uniform flow of air in a direction counter to the flow of heat, while one surface of the ceramic plate was heated …

Investigation Of Vertical Internal Spillways, Paul R. Munger

Masters Theses

"This investigation resulted in the development of a means of predicting the discharge of water through an internal spillway type rockfill dam. From the data obtained during the various tests, equations were developed by which the coefficient of discharge for an internal spillway type rockfill dam can be determined when the core height, rock size and head causing flow are known. The equations give results with an error of less than 5%, which is adequate for engineering works"--Abstract, page 2.

Transient Temperature Distribution In Solid Sphere Subjected To Radiation Heat Exchange, William H. Stocklin

Masters Theses

"The author believes that numerical analysis is the most feasible approach to calculating the transient temperature distribution in a solid sphere subjected to various surface conditions; heat flow within the sphere is radial.

Numerical analysis is employed to arrive at a series of equations for calculating the transient temperature at selected points of a solid sphere. A study is made to determine a method for calculating temperatures with these equations; a computing device is found to be the most practical method for this purpose. The equations for temperatures at internal points of the solid sphere are general.

The equations have …

The Effect Of The Ultraviolet Portion Of The Sun Spectrum On Chlorine Residuals In Water Supplies, Tumkur Mohmed Ameer Ahmed

Masters Theses

"The effect of sunlight on chlorine residuals in water supplies was investigated to provide original and basic information of value to the water purification field.

Three different water systems were employed: (a) The Simplified Water System, (b) The Ground Water System, and (c) The Surface Water System. The RS Sunlamp provided an appropriate source of ultraviolet radiation. A 10 mg/1 chlorine concentration was used. The pH values of 7 and 10 and the illumination intensities of 145 and 200 foot candles were employed. Iodometric determination of chlorine residuals was the main parameter used.

It was found that the chlorine residuals …

Analyses Of Two New Electrode Configurations For Earth Resistivity Surveying, Chi-Chao Chang

Masters Theses

"Two new electrode configurations for the electrical resistivity- surveying are introduced: the A-configuration, consisting of a closely spaced pair of current electrodes separated at larger distance from the closely spaced pair of potential electrodes, and the B-configuration, in which each closely spaced pair consists both current and potential electrode. Because electrode pairs can be carried as units, the new configurations can be applied to continuous resistivity surveying more easily than the Wenner configuration....

Theoretical apparent resistivity values are derived, by Maxwell's theory of images, for the A- and B-configuration over a two layered earth using the depth probe method, and …

Design Of A Square Loop Magnetic Integrating Device, Fred Leland Grismore Jr.

Masters Theses

"The problem investigated in this research was the development of a static integrating circuit applicable to closed loop feedback control systems. Investigation of various methods of attack indicated that square loop magnetic cores offered characteristics required for the integration process. These include the ability to sum input information and the ability to store information for an indefinite period of time.

An experimental program was carried out, investigating the various properties of square loop magnetic materials and required design parameters. Through this work it was verified that the process of integration could be realized by using the partial switching volt-second absorption …

An Investigation Of The Factors Influencing The Design Of A Dense Prilled Ammonium Nitrate-Fuel Oil Mixture, Robert Bartley Hopler Jr.

Masters Theses

"The physical characteristics of dense ammonium nitrate prills were examined. The density was found to be 1.52 grams per cubic centimeter, and from this the specific surface was calculated for the size fractions of interest in the investigation. Theoretical loading densities were calculated for between 26.0 and 47.6 percent voids.

The explosive properties of discrete particle size fractions were investigated. The equation by Clark was found to predict the detonation velocity of the sizes smaller than 8/20 mesh. The equation by Cook could not be applied to dense prilled ammonium nitrate. The possibility of a very oxygen negative condition existing …

Underground Methods Of Working Coal, Hemendra Nath Datta

Masters Theses

"'Underground Methods of Working Coal' is the subject of this thesis. It is the purpose of this investigation to summarize all the mining methods under various conditions of working.

The underground methods of mining have been classified under three headings; viz., (a) Room and Pillar, (b) Longwall and (c) Horizon Mining. The conditions suitable for the applicability of each system and their relative merits and demerits are fully discussed.

The principles of the design of the workings of both room and pillar and longwall systems to have effective roof control in the area of the workings are pointed out.

Distinct …

A Resistivity Study Of Hot Short Ferrous Alloys, Harold Alfred Koelling

Masters Theses

"Resistivity measurements were performed at elevated temperatures on four special ferrous alloys and one commercial iron. The alloys were pure iron, iron with .023 per cent sulfur, iron with .33 copper, iron with .32 copper and .024 sulfur. Other elements were held to the minimum amounts possible in order to determine the actual effects of sulfur and copper. The commercial alloy was Armco Iron.

Measurements of resistivity versus temperature were taken at slow heating rates to determine if the iron sulphide liquid film formed in the grain boundaries of red-short steels had any effect on the electrical resistivity"--Abstract, page 7.

Scatter Matrix Analysis Of Plane Waves In A Layered Media, Bill W. Ashworth

Masters Theses

"The problem was the application of matrix theory to the solution of the reflection and transmission coefficients for a plane wave incident on a layered media. Background material relating to the problem was reviewed. Equations that were used in the solution of the problem were either derived or explained. The derivations for the reflection and transmission coefficients were carried out in order, starting with the simple case of normal incidence on a junction of two infinite media and progressing through the more difficult case of oblique incidence on a layer of finite thickness separating two infinite media. Scatter matrix analysis …

A Study Of The Hood Inlet And Its Possible Use As An Overflow Structure For A Sanitary Lagoon, Richard Irwin Boe

Masters Theses

"A closed conduit, such as an overflow pipe for a conservation pond or a sanitary lagoon, will not flow full if laid on a slope that is hydraulically steep unless the pipe entrance receives special attention. A steep conduit slope is necessary to insure that the pipe entrance controls flow.

The recently introduced hood inlet will permit the closed conduit to flow full, even if on a hydraulically steep slope, upon a slight submergence of the inlet crown. The hood inlet is formed by cutting the pipe at an angle so that the crown of the inlet projects beyond the …

A Preferred Orientation Study Of Sheet Formed By Rolling Copper, Nickel, Titanium And Tungsten Metal Powders, Martin Franklin Marchbanks

Masters Theses

"Pole figure scans of strip rolled from copper, nickel, titanium, and tungsten metal powders were made on samples taken across the width of the strip, and with various amounts of surface material removed, to determine if any preferred orientation existed. No preferred orientation was found in any of the samples examined.

The method used was a modification of the Schultz technique, using the Norelco Pole Figure Fixture, whose geometry and operation is described, in conjunction with the Norelco diffractometer.

Defocusing resulting during the run of a pole figure is discussed and a method for reducing this defocusing is described.

The …

A Study Of Viscous Frictional Effects And Relay Characteristics On The Operation Of A Positional Relay Servomechanism, Earl F. Richards

Masters Theses

"The thesis describes some experimentally observed data and analytical approaches to the study of a relay servomechanism. The experimental data were secured from an analog simulation of a relay servo system. The results of this data were compared to the transient approach by use of the phase-plane method. The stability of the system was determined using a describing-function. The analytical approaches are described in the presentation.

A study of the effects of viscous friction is described, and the characteristic of the relay used in the system is given special attention. The response to input driving function was considered, and rise …

Transient Temperature Distribution In An Infinite Plate Subjected To Convection And Radiation Heat Exchange, Billy W. Marshall

Masters Theses

"The desired result of this paper is a method of calculating transient temperatures in an infinite plate. The resulting equations are general to the extent possible for aerodynamic heating and radiation boundary conditions. The possible methods of calculation were investigated, and it was felt that a numerical analysis presented the most feasible approach.

Numerical analysis was employed to arrive at a series of equations for calculating the temperatures at selected positions in an infinite plate. A study was then made to determine a method of solving these equations by means of some high speed computing device.

The equations were adapted …

Correlation Of Dust-Count Results By Zeiss Konimeter And Midget Impinger, Chandmal Jain

Masters Theses

"In this modern age, the scientific and technological developments have advanced mechanized mining to the status wherein the attendant dust problems have reached very serious hazard proportions. The significant roles, which have been perfected for the Zeiss konimeter and the midget impinger, in evaluating dust concentrations and thereby revealing possible improvements in making the atmospheric conditions safer, cannot be over emphasized.

While introducing the subject of this paper in the first chapter, the author has presented a historical resume, wherein he pointed out that performances of these instruments have not been correlated in the past. However, the work reported on …

Design, Construction And Operation Of Equipment For The Study Of Evaporation Of Aqueous Solutions Using A Simplified Reactor Design Approach, Virendra Kumar Mathur

Masters Theses

"The study of simultaneous heat and mass transfer in flow reactors has attracted the attention of many workers for a long time due to its wide application in the industrial field. These heat and mass transfer studies play an important role in determining the rate equations and in turn the size of the reactor itself. A large number of chemical reactions have been studied by various workers….

The purpose of this work comprised only the initial or exploratory phase of this overall project, and deals with the design, construction and assembling of the equipment necessary to carry out the vaporization …

Test 806: International Td-20 (Diesel), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Australian Tractor Tests : Report On Test No. 34 : Fordson Power Major, G H. Vasey, W. F. Baillie

Journal of the Department of Agriculture, Western Australia, Series 4

THIS Report is taken from the full Technical Report No. 34 of this test; test results are shown here in briefer form: fuller explanations are added.

Values quoted may be rounded out to two instead of three significant figures; to this extent the values may differ slightly but not significantly from those shown in the Technical Report

Some values are taken from graphs shown in the Technical Report, which are not shown here.

Blasting. Part 1. Explosives And The Farmer, G A. Greaves

Journal of the Department of Agriculture, Western Australia, Series 4

ABOUT 3,000 tons of commercial blasting explosives of various types are used every year in Western Australia of which approximately two thirds is utilised by mining industries and the remainder goes mainly to quarrying and public works.

The farmer and orchardist actually use only very small amounts but nevertheless explosives are a very useful working tool for the primary producer.

Australian Tractor Tests : Zetor 50 Super : Report On Test No.35, G H. Vasey

Journal of the Department of Agriculture, Western Australia, Series 4

T H I S Report is taken from the full Technical Report No. 35; results are shown here in briefer form: fuller explanations are added. Values quoted may be rounded out to two instead of three significant figures.

The Effect Of Phosphoric Acid On Compaction And Shear Characteristics Of Pure Kaolin Clay, Bhupat Hargovinddas Mehta

Masters Theses

"The work presented is the investigation of the effect of phosphoric acid on the compaction and shear characteristics of pure kaolin. Pure Georgia kaolin clay average particle size of five microns was mixed with different percentages of phosphoric acid. These mixtures were permitted to react for varying periods of time. The results of the study indicate a notable and gradual increase in dry density of the kaolin with increasing percentages of phosphoric acid admixture. The acid admixture ranges from one up to nine percent of the dry weight of the clay. Increase in cohesion of the clay with increase of …

Crustacean Gastroliths From The Jackson Eocene Of Louisiana, Donna L. Frizzell, Wayne C. Horton

Missouri School of Mines and Metallurgy Bulletins

Wechesia louisianae, n. sp., is described from upper Eocene beds at Montgomery, Louisiana. Second species of the genus, it extends the range of Wechesia Frizzell and Exline from Claiborne (middle) Eocene and validates the generic diagnosis.

New Genera And Species Of Myripristid Fishe~ In The Gulf Coast Cenozoic, Known From Otoliths (Pisces, Beryciformes), Donna L. Frizzell, C. Kurt Lamber

Missouri School of Mines and Metallurgy Bulletins

Studies of fossil and Recent otoliths (sagittae) supply an important line of evidence, bearing on classification of teleost fishes, supplementary to that of anatomy, osteology, and "phylogenetic" paleo ichthyology.

Squirrelfishes (" Holocentridae" of authors) are generalized forms in which evolutionary divergence of some magnitude is reflected in unpreservable details of anatomy, inconspicuous skeletal structures, and striking differentiation of the sagittae. Otoliths show the holocentroid complex to consist of one homogeneous unit (l\fyripristidae, elevated) and another more heterogeneous group (Holocentridae, restricted). These lineages have been separated at least since the middle Eocene.

A revised classification, based on available lines of evidence …

Impact Energy Coupling And Impact Seismic Refraction Using Electronic Timing, Roderick D. Carroll

Masters Theses

"The use of impact energy sources in lieu of explosives for shallow seismic investigations is limited chiefly by the low energy available. Means of increasing the energy transmission of an impact source are investigated, using a weight drop arrangement and an oscilloscope. The energy of refracted arrivals is investigated by direct overburden impacts, compaction of the overburden at the point of impact and the use of steel and aluminum plates as coupling devices. Energy transmission is shown to be greatly increased, using a suitable coupling device and the conditions for optimum coupling are discussed. The elastic constants of the ground …

An Analog Method For The Determination Of The Deflection Of Beams Resting On End Supports And Design Of An Automatic Programming Device, Paul C. Jackson Jr.

Masters Theses

"This investigation shows that beam problems can be solved easily and accurately with an analog computer. Two problems were solved as to their shear, moment, slope and deflection along the length of the beam and the graphs drawn by the analog computer were compared with calculated values. Very little difference was found between them.

An electronic programmer was built to aid in handling beam problems as they were being run on the computer. This was capable of putting into the computer bits of data at specified intervals of time. The programmer proved reliable and repeatable once it was adjusted to …

Electron Microscope Study Of The Systems Cadmium-Cadmium Chloride And Lead-Lead Chloride, Dennis O'Neill

Masters Theses

"The nature of the dispersed phase in the cadmium-cadmium chloride and lead-lead, chloride systems were investigated with the electron microscope.

Preliminary experiments on preparing and examining the dispersed phase showed that it was most feasible to study the material by electron-microscopic examination of replicas made from the surfaces of the fractured materials. Melting apparatus and methods were chosen so that samples of the melts could be easily quenched to different temperatures and so that the samples could be easily fractured with a minimum of surface contamination. Of the conventional replicating techniques tried, that of carbon replicas pre-shadowed with chromium was …

Effect Of Deflections For A Flat Plate By Slope-Deflection-Gyration Method, William Hsin-Loo Ying

Masters Theses

"Since the procedure for the theoretical solution of a rectangular flat plate or slab is complex, many approximate methods for determining the moments and deflections of such plate have recently been developed. One of these methods is the so called Slope-Deflection-Gyration Method which is performed by means of basically well-known structural theories - slope-deflection and torsion.

For a given plate, it is assumed that the plate is to be divided up into a grid of strips or equivalent beams at right angles to each other. The joints of this grid are assumed to be rigidly intersected and be permitted to …

Apparatus For Inductive-Electromagnetic Model Studies, Won Ho Kim

Masters Theses

"The object of this research is to design, construct and calibrate an apparatus suitable for electromagnetic model studies. A portion of the thesis is devoted to general review and theoretical consideration of electromagnetic prospecting.

Theoretical analysis of electromagnetic survey data by mathematical methods can only be carried out for simple idealized subsurface conditions. Because of the difficulties of theoretical solutions, in contrast to the simplicity of the conditions of similitude in electromagnetic exploration, a model experiment offers a very useful means of studying and comparing the response of naturally occuring conducting mineral bodies.

An apparatus suitable for inductive-electromagnetic model studies …

Transpiration Cooling, Herbert S. Brahinsky

Masters Theses

"In the investigation of the problem, it is shown that the process of transpiration cooling is an effective method of cooling. This process may be applied to heat screens or heat shields, as was done in the sample problems worked out here. A porous plate with coolant flowing counter to the flow of heat was used.

The plate temperature is determined by the amount of heat flux, coolant flow, thermal conductivity of the material used as a plate, the specific heat of the fluid, the specific heat of the plate material, the density of the plate material and its porosity. …

Some Aspects Of Miscible Phase Displacement As Applied To The Recovery Of Oil Reservoir Crude, David D. Friend

Masters Theses

"Recent application of the miscible sing displacement process as a method to increase recovery from petroleum reservoirs has resulted in a great deal of laboratory investigation, none of which provided conclusive evidence as to the amount of mixing taking place between the displacing and displaced fluids. This investigation attempts to provide a possible insight into the rate and degree of mixing of two fluids with respect to flow path transversed and the rate of advance of the fluids. The laboratory investigation consisted of displacing a fluid from a packed core with another fluid under completely miscible conditions.

Experimental evidence indicates …