Digital Commons Network^™

A Study Of Air Cleaners And The Effect Of Air Cleaner Design On Horsepower, Roger D. Mcculley

Graduate Research Papers

It is the purpose of this study to investigate air cleaners and the effect of air cleaner housing design, intake snorkel tube design and filter media on engine horsepower. In doing the investigation, the writer will determine how horsepower is affected by: (1) the size and shape of the intake snorkel, (2) the placement of the intake snorkel in the engine compartment, (3) the size (volume) of the air cleaner housing, (4) the type of filtering media used, (5) the size of the filter element, (6) breather holes drilled in the filter housing, and (7) a partially clogged filter element.

Electrical Lighting Design, Thermthip Chamarakula

Graduate Research Papers

In any given space for lighting design, each space presents a unique lighting problem which must be studied. These problems can be considered as physical characteristics of the space and its occupancy and usage.

With respect to. these problems a number of questions must be asked.

1. What are the actual seeing tasks?

2. Is the usage uniform or are different areas utilize< for seeing tasks of varying severity?

3. How should the lighting equipment be?

4. How can the proper quantity and quality of light be established?

5. Will the area be used during both daylight hours and at night, and, if so, are the …

On The Performance Of Some Sequential Multiple-Decision Procedures, Thomas S. Edrington Ii

Electrical and Computer Engineering ETDs

The performance of several sequential procedures for the following multiple-decision problem is investigated. Samples from k random processes (or populations) are available, k at a time (one from each process), to a receiver or data processor. One process contains a signal; the other k - 1 are statistically-identical noise. The receiver is to select the odd process (locate the signal), with prescribed probability of error. The optimal receiver makes the selection in minimum average time. All computation is done under the hypothesis that the processes sampled are Rayleigh; however, a method for extrapolating results to other cases is given. The …

Fabrication Of The Pewee Nozzle; Brazing Nozzles For Rockets Powered By Nuclear Reactors, William C. Turner

Chemical and Biological Engineering ETDs

This thesis describes the steps taken to develop an improved process for brazing nozzles for nuclear-powered rockets. It defines the state of the art prior to this work. It gives an evaluation of the brazing alloys available for use. It shows the methods employed to develop the use of positive fixturing. It describes the use of full-scale sectors to refine processing. This thesis also describes the use of such new processing techniques in the successful production of two nozzles. Gold-nickel-palladium brazing alloys are used. Vacuum atmosphere performs superbly. Bands are used to hold U-tubes into slots in the shell. Problems …

Field Manual Fm 55-8, Transportation Intelligence, 12 March 1970, Robert Bolin , Depositor

United States Department of Defense Military Intelligence

Obviously, reliable information about potential enemy transportation equipment, facilities, systems, capabilities is vital, since our forces may need to prevent an enemy from using them and we may need to use them. Transportation or mobility intelligence is such reliable information. This is a very thorough document describing the collection, production, and dissemination of transportation intelligence. The emphasis of this manual is collection of relevant information in the field.

The manual describes organizations and personnel in the army responsible for collecting transportation related information. It identifies the national-level military intelligence production agencies as:

(a) The Defense Intelligence Agency (DIA) which was …

Electron Emitter Tips And Method, P. D. Ownby

Materials Science and Engineering Faculty Research & Creative Works

Boron is deposited on the (110) plane facet at the center of a tungsten electron emitter tip by chemical vapor deposition of boron triiodide. The emission current density is greatest in the center of the emitting area (FIG. 2).

Ole Miss Engineer 1970

Ole Miss Engineer

No abstract provided.

Pavement Slipperiness Studies, James L. Burchett Jr., Ronalds L. Rizenbergs

Kentucky Transportation Center Research Report

Studies of pavement skid resistance in Kentucky have been in progress since 1956. In 1964, an extensive investigation into the use of an automobile as a testing tool was undertaken and an interim standard method of test was selected. Since then, investigations with the device have continued, both to facilitate meaningful interpretation of skid-test data and to evaluate the skid resistance performance of pavement surfaces.

Variables associated with the testing device, procedures and pavement surfaces were investigated. Several paving projects were tested to determine the number of sites required to obtain a representative result. It was found that on most …

Hydrologic Inventory Of The Uintah Study Unit, Lloyd H. Austin, Gaylord V. Skogerboe

Reports

The 1963 Utah State Legislature authorized the Utah Water and Power Board (now the Utah Division of Water Resources) to develop a state water plan in order to give coordination and direction to the activities of all state and federal agencies concerned with Utah's water resources. To facilitate the development of this plan, a proposal was submitted through the State Planning Coordinator in the Governor's Office to the Urban Renewal Administration of the Housing and Home Finance Agency. Funding was approved effective May 19, 1966, under the Urban Planning Assistance Program authorized by Section 701 of the Housing Act of …

Closed Conduit To Open Channel Usu Stilling Basin, Gordon H. Flammer, Gaylord V. Skogerboe, Chi-Yuan Wei, Hameed Rasheed

Reports

Criterion have been developed for designing a stilling basin to serve as a transition from closed conduit flow to open channel flow for a fully submerged pipe outlet. The unique feature of the stilling basin is the short-pipe energy dissipater so located and designed as to provide maximum energy dissipation for the basin configuration. The expanding characteristics of a submerged jet were used in establishing the length of the stilling basin. The unsteadiness of the water surface and the relative boil height in the model basin were used as the criteria for evaluating the effectiveness of the structure for energy …

Interior Corrosion Of Structural Steel Closed Sections, American Iron And Steel Institute

CCFSS Library (1939 - present)

A survey of light poles, water-tank stanchions, orthotropic deck bridges, marine tubular catwalks, davits and welded steel columns strongly suggests, contrary to some beliefs, that interior surfaces of closed steel sections rust but little in the atmosphere, even when not fully sealed. Only light rusting occurs because amounts of oxy'gen and water in entrapped air are limited and condensation necessary for rusting is infrequent. Computations based on the oxidation reaction taking into account inside surface, volume of entrapped air, relative humidity and air changes show that the loss of iron thickness due to such rusting is negligible. Use of closed …

Freeze-And-Thaw Phenomena In Concretes And Aggregates, James H. Havens

Kentucky Transportation Center Research Report

This report summarizes several years of research relating to damage to concrete and aggregates undergoing freezing and thawing. Basic principles involving freezing and attendant pressures are considered. Application of these principles to the evaluation of concrete was accomplished in experiments on concrete having low and high air contents. The effects of air entrainment upon freeze-thaw resistance were demonstrated.

Freeze-thaw characteristics of saturated aggregates relative to their physical properties such as porosity, absorption and bulk specific gravity were studied by submerging individual particles in pre-chilled mercury. Pressures associated with popouts in concrete were monitored and are presented along with accompanying theoretical …

An Investigation Of Low-Strength Concrete And Resulting Structural Failure In A Bridge Deck, James H. Havens

Kentucky Transportation Center Research Report

This investigation concerns the discovery of weak concrete in a portion of the deck of the Elkhorn City bridge, APD 640(4), within a year after it was opened to traffic. The deck concrete was placed between April 14 and June 14, 1968. The bridge serves heavy coal-trucks traffic. Failures occurred in the eastern-most span (No. 5) in April or May of 1969, Undoubtedly, the heavy loading contributed to early disclosure of defective concrete.

A preliminary investigation was made in May 1969, and reported by memorandum May 21, 1969. The bottom third or half of concrete in the affected portion, Span …

Locating And Tracing Seepage Water In Unstable Slopes, Yasin A. Alkhoja, Gordon D. Scott

Kentucky Transportation Center Research Report

With the increase in modern highway construction, the occurrence of landslides has been growing proportionally due to the use of deeper cuts and higher fills. It has been observed that landslides on highways often occur in fills on hillsides. Accumulation of water in the embankment, usually seeping from a nearby hill, may reduce the shear strength of the embankment soil and result in failure at a later time. Many landslides on Kentucky highways have occurred a few years after construction and obviously have been caused by the gradual weakening of the embankment due to a damming and accumulation of water. …

Slip-Form Paving, Kerry P. Magan

Kentucky Transportation Center Research Report

The proper placement, consolidation, and finishing of low-slump concrete without the aid of pre-erected side, forms has been widely acclaimed as an economical and effective procedure in the construction of portland cement concrete pavements. This construction procedure, commonly referred to as slip-form paving, depends upon the ability of low-slump concrete to remain in place after consolidation and removal of forms.

Slip-form pavers differ from conventional pavers in that no fixed side forms are required inasmuch as the slip-form paver has side forms that advance with the machine. Concrete is merely deposited on the prepared subgrade in front of the machine, …

Final Performance Report On Experimental Use Of Thermoplastic Pavement-Striping Materials, Assaf S. Rahal, Ronald D. Hughes

Kentucky Transportation Center Research Report

This study was undertaken in order to: 1) evaluate the performance of thermoplastic striping materials, 2) compare their performance on both portland cement concrete and bituminous concrete pavements to that of conventional traffic paints, and 3) to evaluate the economics of thermoplastics in terms of cost per mile per day of useful life. The performance of two brands of thermoplastic striping materials and conventional traffic paints applied at nine test sites in both rural and urban areas is reported herein. Application procedures, site locations, repair histories and materials specifications are included. Accumulative costs for each material at all sites for …

Slurry Seal Maintenance Applications, Robert L. Florence, Herbert F. Southgate

Kentucky Transportation Center Research Report

A slurry seal mixture consists of graded fine aggregate (normally minus 3/8-inch material), mixing grade emulsified asphalt (SS-1 or SS-lH), and water. The water is added to aid in mixing and to provide a free-flowing consistency so that the mixture can be spread in thin layers on the surface of an existing pavement. After the mixture is spread, the water evaporates and the remaining material, aggregate and base asphalt, forms a thin seal on the pavement surface which resembles a fine-grained asphaltic-concrete surface. As a result of the free-flowing consistency and the fineness of the aggregate, a slurry mixture readily …

Fluid Friction Reduction By Water Soluble Linear High Polymers, Arthur Edward Davis

Theses

The effects of various dilute aqueous linear high polymer solutions on turbulent pipe flow were studied to determine the polymer most suitable for testing as the drag reducing component in the proposed coating. Results of this study are presented for commercial schedule 40 1/4 inch NPS black iron pipe. Tests were conducted at Reynolds numbers of 6.2x10⁴,8.3x10⁴ and 9.8x10⁴.

Attempts were made to prepare a coating containing a friction drag reducing polymer - Polyhall 295 polyacrylamide - utilizing various techniques of polymer incorporation into the paint including several grinding and dispersion methods, adding the polymer …

Commentary On The 1968 Edition Of The Specification For The Design Of Cold-Formed Steel Structural Members, George Winter

American Iron and Steel Institute (AISI) Specifications, Standards, Manuals and Research Reports (1946 - present)

No abstract provided.

Proceedings Of The International Symposium On Low Cost Housing Problems Related To Urban Renewal And Development, Oktay Ural

International Symposia on Low Cost Housing Problems

PREFACE TO SECOND EDITION--We are very happy to have a second printing of the Proceedings of the First International Symposium on Low-Cost Housing Problems Related to Urban Renewal and Development. The rather quick and large demand of this publication proved to us, once more, the importance and timeliness of the concern on the topic of housing technology and production. The contributions from eighteen nations painted a real picture of housing conditions and needs around the world.

The fifty-one technical papers included in this volume have been selected intentionally in various aspects of housing to draw a complete and meaningful picture …

Column Research Council: Proceedings 1970, Column Research Council

CCFSS Library (1939 - present)

The purposes of Column Research Council are to study and discuss problems related to the stability and strength of metal compression members; to organize research in this field; to disseminate information; and to formulate design rules for consideration by specification-writing bodies. The activities of the Council in 1970 are summarized in this report. A particular feature is the Proceedings of the 1970 Annual Technical Session. As in the past, the rosters of members of the Council and the By-Laws are also included. The support and technical contributions of the members and investigators are sincerely appreciated. Those individuals and organizations that …

Effects Of Cold Work In Cold-Formed Steel Structural Members, S. J. Britvec, Alexander Chajes, K. W. Warren, Jairo Uribe, George Winter

CCFSS Library (1939 - present)

No abstract provided.

Influence Of Ductility On The Structural Behavior Of Light-Gage Cold-Formed Steel Members, A. K. Dhalla, George Winter, S. J. Errera

CCFSS Library (1939 - present)

Ductility parameters defined in the second progress report were previously obtained by conducting tension coupon tests on specially produced A and S steels. In this report, tension coupon test results are presented for a 20 gage commercial low ductility steel, i.e. an ASTM Grade E steel, herein designated as steel B. Its behavior is compared with that of the specially rolled A and S steels to test the validity of conclusions arrived at in the second progress report. Test programs were set up to study the behavior of B steel under static tension loading, one program for single bolted connections …

Systems Reliability Using The Flow Graph, Kenneth Edward Farrier

Dissertations and Theses

The problem of calculating the reliability of a complex system of interacting elements is delineated to a linear system, no element of the system having a reliability distribution in terms of any other e1ement of the system, where only one path is taken through the system at a time. A precise definition is then developed to specify the reliability of the linear, single path at a time, system. A precise and concise generating function is found that effortlessly produces the reliability of the linear, single path at a time, system directly from the reliability flew graph of the system.

Case Study And Analysis Of A Low Cost Housing Project In An Urban Area In India, P. Purusothaman, Jawalker K. Sridhar Rao

International Symposia on Low Cost Housing Problems

An urban development project involving residential and school buildings as an extension of Madras city is described. The analysis of the project is made using the systems approach as a problem of human settlements. The methods adopted for efficient utilisation of space at optimal cost by functional planning, use of prefabricated units and use of new constructional procedures is described. The interrelationship between environmental, technical, social, cultural, psychological, economic, financial and management factors in making decisions for the project is discussed.

A Case For University Credits For Industry's In-House Continuing Education Programs, Robert E. Carlile

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

The minerals industries have long recognized the tangible and intangible returns from continuing education programs for their technical scientific and administrative personnel. These programs originate from the mutual desires of the employer to upgrade the professional competence of the employee and the employee's concurrent desires to keep abreast of new developments to review the state of the art of specialized subjects and to better qualify himself to compete in an every changing technology. In-house training and continuing education programs to provide such review and education for the employee are becoming a recognized function of companies comprising this industry. These company-sponsored …

A Theory On Interpreting Engine Noises, Robert C. Erickson

Undergraduate Student Work

Mechanics have always used sounds to "trouble shoot" an engine. To a trained ear, each sound is different. Since an ear can be this sensitive, this paper will attempt to prove that electronic equipment can be considerably more accurate in detecting engine problems. The writer of this paper has attempted a project in which he hopes to prove that valve and bearing problems can be located by studying oscilloscope displays. These displays would picture the sound frequencies of valve and bearings in operation. The writer assumed that a comparison could be made of the displays of a normal engine operation …

A History Of Maine Roads 1600 - 1970, State Highway Comission

Maine Collection

A History of Maine Roads 1600 - 1970.

State Highway Commission, Augusta, Maine, 1970.

Sections: Two Transportation Firsts, Early Roads, The Stagecoach Arrives, Steamboats and Railroads, Better Roads Movement, The Automobile, State Roads, First Highway Commissioner, State Highway Department, State Highway Commission, Patrol Maintenance, Bridge Law, Federal Aid, Highway Finances, World War 1, First Route Markers, Traffic Counts, Snow and Ice Control, Planning Activities, World War 2, The Maine Turnpike, Right of Way, Division Offices, Chairman Full-Time Position, Engineering Tools and Techniques, Engineering Pioneers, The Interstate Program, Roadside Beauty, Highway Safety, Operation of the Department Today.

The Proposed Eastern Nebraska International Airport Plan, George T. C. Peng, Joseph H. Bain

Nebraskiana Publications: Resources and Materials on the 37th State

Excerpt from the prologue:

Passenger growth has led to expansion of facilities at both the Omaha and Lincoln airports; but like many others in the nation, they are rapidly becoming congested. The Federal Aviation Administration, the State Government officials, and many civic leaders in Nebraska are now becoming aware of the need for establishing a regional airport for the Eastern Nebraska region in order to promote and handle international air transportation for the future. People are also beginning to think of such a modern airport as an essential factor in bringing new industries to Nebraska and in shaping the urbanization …

Test 1045: International Farmall 826 Diesel (Also International 826 Diesel), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT

GENERAL CONDITIONS

East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers.

PREPARATION FOR PERFORMANCE RUNS

The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …