Digital Commons Network^™

Optimum Energy Allocation For Detection In Wireless Sensor Networks, Krishna Kishore Gunturu

LSU Master's Theses

The problem of binary hypothesis testing in a wireless sensor network is studied in the presence of noisy channels and for non-identical sensors. We have designed a mathematically tractable fusion rule for which optimal energy allocation for individual sensors can be achieved. In this thesis we considered two methods for transmitting the sensor observations; binary modulation and M-ary modulation. In binary modulation we are able to allocate the energy among the sensors and protect the individual quantized bits where as the M-ary modulation provides optimum energy allocation only among the sensors. The goal is to design a fusion rule and …

Development Of A Biomass Transducer For Automated Microalgal Bioreactors, Amar Shivaram Hegde

LSU Master's Theses

A highly sensitive miniaturized biomass transducer is necessary for continuous and reliable monitoring of the microalgal biomass in a computer controlled, automated microalgal bioreactor. Previous known methods to determine microalgal biomass applicable in these bioreactors are based on single wavelength turbidimetric or fluorescence. The objectives of this research were to (1) determine the light absorption characteristics of some commercially applicable microalgae in the electromagnetic wavelength range of 200-800 nm (2) design and construct a new miniaturized biomass transducer (3) process the transducer output to correlate with the biomass. Wavelength sensitivity analysis was conducted on the commercially important microalgal species - …

Study Of Demolding Process In Thermal Imprint Lithography Via Numerical Simulation And Experimental Approaches, Zhichao Song

LSU Master's Theses

The objective of present study was to analyze the mechanical behavior of polymer resist during the demolding process, such as stress distribution and evolution; distortion and tilt of microstructures in thermal imprint lithography, a new emerging technique in mass production of micro/nanoscale patterns. One of the most challenging technical issues for thermal imprint lithography is the structural damages during demolding process. Thermal stress, adhesion force and friction force all play important roles in determination of the success of demolding and it is crucial to understand the underlying physics in order to optimize the structure and process design. In present study, …

Experimental And Modeling Studies Of Contaminant Transport In Capped Sediments During Gas Bubble Ebullition, Qingzhong Yuan

LSU Doctoral Dissertations

Fluxes of the three organics and eighteen metals from sediments were measured with diffusion chambers, and the effectiveness of a sand cap ascertained. The influence of sediment consolidation on contaminant flux and the mass transfer coefficient at the sediment-water interface was studied. A two-layer diffusion-advection model and consolidation model were coupled to elucidate the effect of sediment consolidation on chemical transport in the sediment-cap system. The model was tested and verified by the experimental data from microcosms, and then was used to predict phenanthrene flux under field conditions. The simulation results showed that consolidation could accelerate phenanthrene breakthrough and enhance …

Measuring Skeletal Kinematics With Accelerometers On The Skin Surface, Kevin Curtis Ayer

LSU Master's Theses

The most common motion analysis method uses cameras to track the position of markers on bodily surfaces over time. Although each species has a common skeletal frame to reference recorded motions, the soft tissue covering each is not rigid. Markers, therefore, experience motion relative to the bone and do not accurately portray underlying bone activity. This limits clinical use of motion studies and the understanding of joint motion. Use of MEMS accelerometers for removing soft tissue artifact, motion relative to the bone, from surface measurements and determining the position of the underlying bone was investigated. An animal limb was modeled …

Measurements And Computations Of The Flow In Full-Scale Sugar Evaporative-Crystallizers And In Lab-Scale Models, Luis Fernando Echeverri

LSU Doctoral Dissertations

The circulation of massecuite is a key factor in achieving efficient heat transfer and crystallization in sugar evaporative crystallizers, and should be as high as practically possible for recovery, quality, and capacity reasons. This research report presents results on the circulation obtained applying modern experimental and numerical techniques. The main goals are contributing to expand the understanding of the process in sugar crystallizers; developing realistic models for the simulation of the circulation; and studying the effect of different design parameters. The circulation of massecuite is driven by buoyancy force due to density difference between the vapor generated and the surrounding …

Juvenile Crawfish (Procambarus Clarkii) Lc50 Mortality From South Louisiana Crude, Peanut And Mineral Oil, Okey Umejuru

LSU Master's Theses

Nearly every continent has species of crawfish that inhabit wetlands or are near coastal areas where petroleum and other oils are produced, transported, and accidentally released. Most crawfish cannot tolerate polluted water. Thus, they could serve as biomonitors of fossil fuel, biofuel, and other oil releases and assess potential negative impacts such oils have on wetland and coastal ecosystems. The objectives of this study were to estimate the acute toxicity of three oils to juvenile crawfish and determine if toxicity was due to poisoning or interference with oxygen transfer across the gills. Juvenile crawfish (Procambarus clarkii) were tested for acute …

Direct White Sugar Production: Optimization And Chemical Regeneration Of Fixed-Bed Activated Carbon Adsorbers, Raul Alejandro Cortes

LSU Master's Theses

A system for the direct production of white sugar from clarified sugar cane juice in a raw sugar factory has been developed at the Audubon Sugar Institute. This Direct White Sugar Production (DWiSP) system employs a series of columns packed with adsorbent media. Activated carbon is used in the first column(s) as a filter and bulk decolorizer. Ion exchange resins are then used to remove ash and remaining color. Batch testing was performed in order to determine equilibrium parameters. An analytical model was utilized in conjunction with column loading tests to determine dynamic characteristics of the carbon adsorber for use …

Characterization Of Polyethylene Glycol Hydrogels For Biomedical Applications, Anushree Datta

LSU Master's Theses

Polyethylene glycol is one of the most widely used synthetic materials for biomedical applications. Its biocompatibility, flexibility, and 'stealth' properties make it ideal for use in drug delivery applications. The main objective of this paper is to characterize the structural and mass transfer properties of polyethylene glycol hydrogels for applications in drug delivery and biological immobilization. Swelling behavior of the gels was studied to determine the mesh size, and other significant structural parameters of the gel. For accurate design of drug delivery device, along with network design, mathematical modeling of release profiles was performed. The study of PEG hydrogels was …

Development Of Micropump For Microfluidic Applications, Dong Eun Lee

LSU Doctoral Dissertations

This dissertation covers the research work on two types of micropumps, one is based on magnetohydrodynamic (MHD) principle that utilizes Lorentz force for actuation, and the other is based on electrochemical actuation. The AC-type MHD micropump was designed and analyzed as a solution to the bubble formation problem encountered in DC-type MHD micropump. A UV-LIGA process using thick layer of SU-8 negative photoresist was successfully developed to microfabricate the AC MHD micropump. Preliminary studies and tests of the AC MHD micropumps demonstrate that bubble formation was significantly reduced to permit the proper function of the micropump. A continuous flow was …

Measurement And Modeling Of Light Transmission Through Turbid Media, Alois (Al) J. Adams, Michael Fahrenwald, Long Do

Journal of the Arkansas Academy of Science

No abstract provided.

Non-Intrusive Pressure Measurement In Microchannels, Derek Fultz

Dissertations, Master's Theses and Master's Reports - Open

A non-intrusive interferometric measurement technique has been successfully developed to measure fluid compressibility in both gas and liquid phases via refractive index (RI) changes. The technique, consisting of an unfocused laser beam impinging a glass channel, can be used to separate and quantify cell deflection, fluid flow rates, and pressure variations in microchannels. Currently in fields such as microfluidics, pressure and flow rate measurement devices are orders of magnitude larger than the channel cross-sections making direct pressure and fluid flow rate measurements impossible. Due to the non-intrusive nature of this technique, such measurements are now possible, opening the door for …

Security Architecture Methodology For Large Net-Centric Systems, Njideka Adaku Umeh

Masters Theses

"This thesis describes an over-arching security architecture methodology for large network enabled systems that can be scaled down for smaller network centric operations such as present at the University of Missouri-Rolla. By leveraging the five elements of security policy & standards, security risk management, security auditing, security federation and security management, of the proposed security architecture and addressing the specific needs of UMR, the methodology was used to determine places of improvement for UMR"--Abstract, page iii.

Bridge Damage Detection Using An Intelligent Engineering System, Dionysios N. Danilatos

Masters Theses

"This thesis concerns the design of an algorithm that is capable to detect structural damage in civil infrastructure bridges. The algorithm, which will be dubbed Damage Diagnostics System throughout the thesis, is the software component of a broader Bridge Health Monitoring System. This broader system integrates software and hardware,such as sensors and data acquisition components...The rationale for the Structural Damage Diagnosis is based on the principle of the structural vibration testing. The Health Monitoring System captures the vibration signals, as the bridge responds to excitation from various sources. The purpose of the Diagnostic System is to extract information from the …

Analysis Of Soil Erosion Based On Soil Properties, Preetha Veeraraghavan

Masters Theses

"The objectives of this research were to identify the major soil parameter(s) that affect the erosion rate of soil and to estimate the erosion rate based on those soil parameters. Both prepared samples and natural samples were used in this research. The soil properties analyzed were the water content, unit weight, Atterberg limits, and soil cohesion. The erosion rate was determined using a rectangular flume and a linear relation between the erosion rate and shear stress was established from the flume experiment. The slope of the linear relation was a good indicator of the soil's erosion rate. The erosion rate …

Adhesion-Delamination Mechanics Of Linear And Axisymmetric Film At Film-Substrate Interface, Ming-Fung Wong

Masters Theses

"This thesis is to characterize the thin membrane adhesion-delamination phenomena which occur in biological cells and micro-electro-mechanical systems (MEMS) operation. The delamination of a thin film adhered to a rigid substrate is subjected to the coupling effects of tensile residual stress and interfacial adhesion energy. The adhesion-delamination mechanics is derived using the classical linear elasticity and thermodynamics energy balance. The membrane deformation is here dominated by a mixed plate-bending and membrane-stretching, while the concomitant stress is neglected. An 1-dimensional model is first investigated where a pre-stressed rectangular film clamped at both ends delaminates from a rigid punch of the same …

Synthesis, Characterization And Application Of Pd-Pt Bimetallic Nanoparticles And Carbon Nanotubes Supported Nanocomposites, Guoqiang Ren

Masters Theses

"A study on the synthesis of Pd-Pt alloy nanoparticles and composition evolution of the alloys was reported. The synthesis followed a hot organometallic route, with Pd and Pt acetylacetonate as the metal precursors and trioctylphosphine as the solvent. The size of the Pd-Pt nanoparticles narrowed down with time and reached a final size of 3.5 nm in about 10 min. The alloy compositions evolved with time and reached the preset Pd to Pt ratio of precursors in 120 min. An atomic exchange process between the Pt-TOP complex and the Pd atoms at the nanoparticle surface was proposed to elucidate this …

Development, Modeling, And Simulation Of A Nano Aerial Vehicle Using Empirical Data, Wyatt Emery Davenport

Masters Theses

"The ultimate goals of this study were to use experimental data to estimate the flight capabilities of a flapping wing nano aerial vehicle (NAV), estimate the power required to provide such flight, and develop a controller approach for future use in the design of this aircraft. The experimental data is a collection of measurements of the normal force on a flapping wing taken in stationary water, and was used to develop empirical coefficient derivatives for use in the dynamic modeling of the NAV"--Abstract, page iii.

Indot Guidance Document For In-Situ Soil Flushing, Linda S. Lee, Xihong Zhai, Jaesun Lee

JTRP Technical Reports

Many of the Indiana Department of Transportation (INDOT) sites are contaminated with aromatic hydrocarbons and chlorinated solvents; these contaminants often occur in the form of light non-aqueous phase liquids (LNAPLs) or dense non-aqueous phase liquids (DNAPLs). Considerable effort has recently been focused on developing in-situ technologies for removing or destroying NAPL source zones, and several potentially viable methods have emerged including cosolvent-enhanced source zone removal. Most recently, site-specific remedial designs involving a combination of in-situ methods (often referred to as a treatment train) have been proposed for which data are still sparse. The primary goal of the laboratory experiments is …

2007 Civil And Environmental Engineering Department News, Department Of Civil And Environmental Engineering, Michigan Technological University

Department of Civil, Environmental, and Geospatial Engineering Newsletters

Table of Contents

• Student Memorial Awards
• Student Awards
• Engineers Without Borders
• CEE Fulbright Scholars
• New Faculty
• Faculty Grants
• Faculty Awards
• Haltenhoff Memorial
• Environmental Outreach Center
• University Transportation Center
• Environmental Research
• Department Info
• Concrete Canoe

Dispersion Of Water For Impulse Propagation, Shu Xiao, Karl H. Schoenbach

Bioelectrics Publications

This paper calculates the dispersive loss of water when a Gaussian impulse, or a step function impulse travels over a distance. The minimum risetime t_mr was calculated.

Biotechnology, Life Sciences And Control Engineering:Some Synthesis Issues, Aidan O'Dwyer

Conference papers

The synthesis of biotechnology, life sciences and control engineering is receiving increasing interest. The purpose of this contribution (and the associated poster) is to raise awareness of some of this synthesis work.

A Pda Based Recording System To Investgate Heart Rate, Marcos Efren Bolanos

Open Access Theses & Dissertations

Diabetes is one of most afflicting diseases in society which is caused by the inability of the body to appropriately use insulin to balance sugar levels. Type 1 diabetics require monitoring of their glucose levels to ensure a normal glucose level is maintained between 90 and 130 mg/dL (milligrams per deciliter). Unfortunately, current methods of monitoring are based on invasive and painful sampling of the blood. It was imperative that noninvasive and painless methods of monitoring glucose should be explored. A proven noninvasive technique utilizing infrared light to detect the fluctuations in the heart rate was used to determine if …

Understanding Behavior Of System Of Systems Through Computational Intelligence Techniques, Nil H. Kilicay, Cihan H. Dagli

Engineering Management and Systems Engineering Faculty Research & Creative Works

The world is facing an increasing level of systems integration leading towards systems of systems (SoS) that adapt to changing environmental conditions. The number of connections between components, the diversity of the components and the way the components are organized can lead to different emergent system behavior. Therefore, the need to focus on overall system behavior is becoming an unavoidable issue. The problem is to develop methodologies appropriate for better understanding behavior of system of systems before the design and implementation phase. This paper focuses on computational intelligence techniques used for analysis of complex adaptive systems with the aim of …

The Case Method: Using Case Based Instruction To Increase Ethical Understanding In Engineering Courses, Brock Barry, Aman Yadav

School of Engineering Education Graduate Student Series

The case method: Using case-based instruction to increase ethical understanding in engineering courses Introduction

The paper presents a discussion of how case-based instruction is performed and the perceived benefits of its application. We begin with a brief discussion of the historical background of case- based instruction and then discuss the use of case methodologies within various educational contexts. Connections are then made to its use in general ethics instruction, as well as specifically engineering ethics instruction. Finally, we conclude the paper with a call for rigorous education research to compare the various methods of ethics instruction, including case-based instruction, and …

Storm Chamber Technology For Storm Water Storage And Gray Water Management And Reuse, Purdue Ect Team

ECT Fact Sheets Archive

StormChamber™ is an open bottom, arch-shaped, HDPE infiltration chamber which functions in both permeable and non-permeable soils for subsurface retention, detention, recharge and reuse of storm water, or gray water, designed to overcome the deficiencies of other technologies. It provides a higher level of nutrient and pollutant removal by taking advantage of the natural biological and physical properties of the soil. StormChamber™ systems mimic pre-development conditions by putting post-construction run off back into the ground approximately where it used to go, maintaining base flow to streams, wetlands, lakes, ponds and countering salt-water intrusion in coastal areas.

Air Ventilation Protection System For Building Security, Purdue Ect Team

ECT Fact Sheets Archive

The new technology to solve the limitation of conventional Collective protection equipment (CPE) system has been developed as "Combined ESP/ESF/PCO and microfibrous media CPE application". This concept of this new technology is the combination of the both systems; 1) Microfibrous Material Technology, and 2) Photocataytic Oxidation Technology.

Funnel & Gate System, Purdue Ect Team

ECT Fact Sheets Archive

The limited success and high cost of traditional 'active' ground-water-contaminant plume management efforts (i.e., pump-and-treat systems) has stimulated a search for less expensive 'passive' plume interception and in-situ treatment technologies. The 'funnel and gate system,' which uses heterogeneous (surface-mediated) reactions on porous media to degrade dissolved contaminants, is one passive technology under consideration.

Chemical Cleaning Process For Porable Water Distrubution Pipe Systems, Purdue Ect Team

ECT Fact Sheets Archive

Aging potable water distribution pipe systems are becoming a major concern throughout the world. Deterioration of water quality and service as a result of micro biological tuberculation and corrosion continues to increase. Major costs for replacement or rehabilitation of distribution systems are being faced by most communities. The chemical cleaning solution is an organic oxide scavenger which is mixed with a predetermined quantity of muriatic acid and circulated through an isolated section of the water main.

Plasma Arc Torch Technology, Purdue Ect Team

ECT Fact Sheets Archive

For many years, in-situ thermal vitrification has been recognized as one method to remediate contaminated soils and help stabilize land fills. However, the complexity of the process and the uncertainty of the results have limited the use of this remediation technique.A plasma is a gas that has been ionized by the electric arc of a plasma torch and can therefore respond to electrical and magnetic fields. Plasma arc technology can create plasma using almost any type of gas (oxygen, nitrogen, carbon monoxide, air, etc.) and in a wide range of pressures (vacuum to 20 atmospheres).The process of plasma remediation of …